Search NASA⌕ Search

SEARCH · Search NASA

Results for “Internal Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Investigation of Inlet Concepts for Maneuver Improvement at Transonic Speeds

A 15 percent scale lightweight fighter type inlet forebody was tested in the Ames 14 foot transonic wind tunnel at Mach numbers of 0.7, 0.9, and 1.04. The inlet was a two dimensional horizontal ramp system designed for a Mach number of 2.2. Four inlet devices designed to prevent or delay cowl-lip boundary layer separation or to improve the inlet internal flow characteristics at high angles of attack were investigated. The devices used to control cowl-lip separation consisted of cowl leading edge flaps, slotted flaps, and tangential blowing. To improve the internal flow characteristics, discrete jet nozzle flows were directed downstream and parallel to the duct surface in the subsonic diffuser to energize the wall boundary layer. The discrete jets used in the subsonic diffuser were also tested in combination with each of the cowl leading edge devices. Test measurements included engine-face total pressure recovery, steady state distortion, dynamic distortion, duct boundary layer profiles, and duct-surface static pressures.

Latham, E.↗
DOE OSTI2021

A Poisson equation method for prescribing fully developed non-Newtonian inlet conditions for computational fluid dynamics simulations in models of arbitrary cross-section

Prescribing inlet boundary conditions for computational fluid dynamics (CFD) simulations of internal flow in complex geometries such as anatomical vascular models is challenging. In the absence of patient-specific inlet velocity data, a common approach for long blood vessels is to assume that the inlet flow is fully developed. In vessels of irregular cross section, however, prescribing fully developed conditions is complicated due to the lack of a general closed-form analytical solution. In this study, we develop a simple Poisson equation method for prescribing fully developed inlet conditions for the flow of either Newtonian or non-Newtonian fluids in CFD models of arbitrary cross-section. We first derive the generalized Poisson equation for fully developed flow of a non-Newtonian fluid and we then develop and verify a methodology for numerically computing the solution on any planar boundary domain. In addition, we develop a simple extension of the method for prescribing a non-orthogonal inlet velocity that represents fully developed flow from an upstream tube that is connected to the CFD inlet at a non-orthogonal angle. This may be used to investigate a common source of uncertainty in CFD simulations of internal flow that is due to a lack of information concerning the exact streamwise flow direction at the inlets. Comparison to several Newtonian and non-Newtonian benchmark verification solutions shows the method to be extremely accurate. As a practical demonstration case, we use the method to prescribe fully developed conditions on multiple non-circular inlets for the non-Newtonian flow of blood in a patient-specific model of the inferior vena cava (IVC). Finally, we further demonstrate the utility of the method by performing a sensitivity study using the patient-specific IVC model, wherein we investigate the influence of inlet velocity flow direction on the non-Newtonian IVC hemodynamics. Given its simplicity and computational efficiency, the method is shown to be far superior to alternative approaches for prescribing fully developed inlet conditions in such complicated geometries. In conclusion, to facilitate the adoption of our Poisson equation method, we have distributed our OpenFOAM source code and the associated test cases from this study as open-source software.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2004

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Biesiadny, Thomas J.↗
NASA NTRS1975

Internal cowl-separation at high incidence angles

Internal flow separation at large incidence angles is studied on the basis of wind-tunnel pressure data for six axisymmetric inlet geometries. The inlet geometric variables investigated are the angle of incidence, the throat Mach number, the internal lip contraction ratio, 'sharpness' of the external shape, and freestream velocity. It is shown that an increase in lip contraction ratio delays internal flow separation, while an increase in the sharpness of the external profile tends to reduce the angle of incidence at which complete flow separation occurs. It is also shown that inlet flow separation is subject to scale effects associated with the boundary layer on the cowl surface. The scale effects are particularly pronounced at very high throat Mach numbers.

Jakubowski, A. K.↗
NASA NTRS1995

General Fluid System Simulation Program to Model Secondary Flows in Turbomachinery

The complexity and variety of turbomachinery flow circuits created a need for a general fluid system simulation program for test data anomaly resolution as well as design review. The objective of the paper is to present a computer program that has been developed to support Marshall Space Flight Center's turbomachinery internal flow analysis efforts. The computer program solves for the mass. energy and species conservation equation at each node and flow rate equation at each branch of the network by a novel numerical procedure which is a combination of both Newton-Ralphson and successive substitution method and uses a thermodynamic property program for computing real gas properties. A generalized, robust, modular, and 'user-friendly' computer program has been developed to model internal flow rates, pressures, temperatures, concentrations of gas mixtures and axial thrusts. The program can be used for any network for compressible and incompressible flows, choked flow, change of phase and gaseous mixturecs. The code has been validated by comparing the predictions with Space Shuttle Main Engine test data.

Majumdar, Alok K.↗
NASA NTRS1987

Application of CFD codes to the design and development of propulsion systems

The internal flows of aerospace propulsion engines have certain common features that are amenable to analysis through Computational Fluid Dynamics (CFD) computer codes. Although the application of CFD to engineering problems in engines was delayed by the complexities associated with internal flows, many codes with different capabilities are now being used as routine design tools. This is illustrated by examples taken from the aircraft gas turbine engine of flows calculated with potential flow, Euler flow, parabolized Navier-Stokes, and Navier-Stokes codes. Likely future directions of CFD applied to engine flows are described, and current barriers to continued progress are highlighted. The potential importance of the Numerical Aerodynamic Simulator (NAS) to resolution of these difficulties is suggested.

Lord, W. K.↗
NASA NTRS1990

Real-time simulation of supersonic inlets

A previously published real-time simulation algorithm, the matrix stability region placement (MSRP) method, is used to simulate a small perturbation model of the NASA Lewis Mach 2.5 40-60 mixed compression inlet. The model is representative of high-speed internal flow propulsion systems which can be approximated as quasi-one-dimensional flows. The resulting system of equations, which is stiff, is also simulated by the second-order Adam-Bashforth method. It is shown that the MSRP method can be used to simulate small perturbation models of high-speed internal flow propulsion systems in real time.

Mossayebi, F.↗
NASA NTRS1990

Transitions from Hadley to Rossby flows in internally forced rotating spherical systems

The possibility of global-scale transitions between the Hadley and Rossby atmospheric regimes is investiated using a simple three-dimensional rotating spherical model without a boundary layer structure, bottom topography, or cumulus friction, and the expected occurrence of the Hadley to Rossby transition is demonstrated. It is shown that a transition from Hadley flow to wavenumber-5 Rossby flow is preferred, in agreement with standard baroclinic instability results. This result gives a reasonable Rossby wave bifurcation from the Hadley solution. For the cases examined, it was found that the upper symmetric Hadley regime does not exist and that the Hadley to Rossby transition depends on the values of the eddy viscosities.

Higgins, Wayne R.↗
NASA NTRS1983

A one-dimensional unsteady model of dual mode scramjet operation

A one-dimensional unsteady model and code have been developed which can handle internal flows involving area change, heat release, transients and coupled inviscid core-boundary layer flows. The model has been shown to work well in diverging channels with a supersonic entrance Mach number and unseparated boundary layers. Transient flows have also been studied. The model needs no prior knowledge of shock (or shocks) location and can be extended to two or three dimensions. The results show that the one-dimensional unsteady model developed here can be used for analysis of internal flows as occur in scramjet combustors.

Bussing, T. R. A.↗
DOE OSTI2020

Time-resolved 3D imaging of two-phase fluid flow inside a steel fuel injector using synchrotron X-ray tomography

The multiphase flow inside a diesel injection nozzle is imaged using synchrotron X-rays from the Advanced Photon Source at Argonne National Laboratory. Through acquisitions performed at several viewing angles and subsequent tomographic reconstruction, in-situ 3D visualization is achieved for the first time inside a steel injector at engine-like operating conditions. The morphology of the internal flow reveals strong flow separation and vapor-filled cavities (cavitation), the degree of which correlates with the nozzle's asymmetric inlet corner profile. Micron-scale surface features, which are artifacts of manufacturing, are shown to influence the morphology of the resulting liquid-gas interface. The data obtained at 0.1 ms time resolution exposes transient flow features and the flow development timescales are shown to be correlated with in-situ imaging of the fuel injector's hydraulically-actuated valve (needle). As more than 98.5% of the X-ray photon flux is attenuated within the steel injector body itself, we are posed with a unique challenge for imaging the flow within. Time-resolved imaging under these low-light conditions is achieved by exploiting both the refractive and absorptive properties of X-ray photons. The data-processing strategy converted these images with a signal-to-noise ratio of similar to 10 into a meaningful dataset for understanding internal flow and cavitation in a nozzle of diameter 200 mu m enclosed within 1-2 millimeters of steel.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1981

Navier-Stokes solutions for nonaxisymmetric nozzle flows

The compressible Navier-Stokes equations for two-dimensional and three-dimensional flow are solved for nonaxisymmetric nozzle configurations. Both internal flow alone and combined internal and external flow cases are considered. An implicit approximate factorization algorithm is employed to solve the governing equations which are cast in terms of a body-fitted coordinate system. Turbulence closure is accomplished with a composite algebraic model. Two-dimensional results for a wedge plug nozzle flow in the form of surface pressures compare favorably with experimental data. Three-dimensional calculations for two nonaxisymmetric nozzles are also presented and compared with data.

Swanson, R. C.↗
NASA NTRS1992

A two-phase restricted equilibrium model for combustion of metalized solid propellants

An Eulerian-Lagrangian two-phase approach was adopted to model the multi-phase reacting internal flow in a solid rocket with a metalized propellant. An Eulerian description was used to analyze the motion of the continuous phase which includes the gas as well as the small (micron-sized) particulates, while a Lagrangian description is used for the analysis of the discrete phase which consists of the larger particulates in the motor chamber. The particulates consist of Al and Al2O3 such that the particulate composition is 100 percent Al at injection from the propellant surface with Al2O3 fraction increasing due to combustion along the particle trajectory. An empirical model is used to compute the combustion rate for agglomerates while the continuous phase chemistry is treated using chemical equilibrium. The computer code was used to simulate the reacting flow in a solid rocket motor with an AP/HTPB/Al propellant. The computed results show the existence of an extended combustion zone in the chamber rather than a thin reaction region. The presence of the extended combustion zone results in the chamber flow field and chemical being far from isothermal (as would be predicted by a surface combustion assumption). The temperature in the chamber increases from about 2600 K at the propellant surface to about 3350 K in the core. Similarly the chemical composition and the density of the propellant gas also show spatially non-uniform distribution in the chamber. The analysis developed under the present effort provides a more sophisticated tool for solid rocket internal flow predictions than is presently available, and can be useful in studying apparent anomalies and improving the simple correlations currently in use. The code can be used in the analysis of combustion efficiency, thermal load in the internal insulation, plume radiation, etc.

Sabnis, J. S.↗
NASA NTRS1942

High-speed Tests of a Ducted Body with Various Air-outlet Openings

Test of a ducted body with Internal flow were made in the 8-foot high-speed wind tunnel for the purpose of studying the effects on external drag and an critical speed of the addition of efficient inlet and outlet openings to a basic streamline shape. Drag tests of a 13.6- inch-diameter streamline body of fineness ratio 6.14 were made at Mach numbers ranging from 0.20 to 0.75. The model was centrally mounted on a 9-percent-thick airfoil and was designed to have an efficient airfoil-body juncture and a high critical speed. An air inlet at the nose and various outlets at the tail were added: drag and internal-flow data were obtained over the given speed range. The critical speed of the ducted bodies was found to be as high as that of the streamline body. The external - drag with air flow through the body did not exceed the drag of the basic streamline shape. No appreciable variation in the efficiency of the diffuser section of the internal duct occurred throughout the Mach number range of the tests.

Becker, John V.↗
NASA NTRS1980

The effect of throat contouring on two-dimensional converging-diverging nozzles at static conditions

An experiment was conducted at static conditions to determine the internal performance effects of nozzle throat contouring, the result of increasing the circular-arc throat radius. Five nonaxisymmetric converging-diverging nozzles were tested at nozzle pressure ratios up to 9.0. Data are presented as internal thrust ratios, discharge coefficients, and static-pressure distributions. Comparisons of internal performance data for the five nozzles show that throat contouring increases the value of discharge coefficient but has no significant effect on internal thrust ratio except in cases of internal flow separation. To illustrate the use of the two dimensional converging-diverging (2-D C-D) nozzle data base, a two dimensional inviscid theory was applied to the five configurations. The generally good agreement of data with theoretical results indicates that two-dimensional inviscid theory can be successfully applied to the prediction of 2-D C-D nozzle internal flow.

Mason, M. L.↗
NASA NTRS2010

The NASA Langley Isolator Dynamics Research Lab

The Isolator Dynamics Research Lab (IDRL) is under construction at the NASA Langley Research Center in Hampton, Virginia. A unique test apparatus is being fabricated to support both wall and in-stream measurements for investigating the internal flow of a dual-mode scramjet isolator model. The test section is 24 inches long with a 1-inch by 2-inch cross sectional area and is supplied with unheated, dry air through a Mach 2.5 converging-diverging nozzle. The test section is being fabricated with two sets (glass and metallic) of interchangeable sidewalls to support flow visualization and laser-based measurement techniques as well as static pressure, wall temperature, and high frequency pressure measurements. During 2010, a CFD code validation experiment will be conducted in the lab in support of NASA s Fundamental Aerodynamics Program. This paper describes the mechanical design of the Isolator Dynamics Research Lab test apparatus and presents a summary of the measurement techniques planned for investigating the internal flow field of a scramjet isolator model.

Middleton, Troy F.↗
NASA NTRS1979

Analysis and computation of viscous subsonic primary and secondary flows

A new approximate flow analysis, designed to enable numerical solution as an initial value problem, is developed for a wide class of viscous subsonic flows at high Reynolds number and in straight or smoothly curved three-dimensional flow geometries. The analysis is coordinate-independent and corrects an a priori known inviscid primary flow for viscous and thermal effects, secondary flows, total pressure distortion, internal flow blockage and pressure drop. Computed results include laminar solutions for three-dimensional boundary layer flow, fully viscous flow in circular arc ducts, and also flow in a curved duct shaped like a turbine blade passage.

Briley, W. R.↗