Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ionic Solutions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Imaging a solvent-swollen polymer gel network by open liquid transmission electron microscopy

Visualizing the network of a solvent-swollen polymer gel remains problematic. To address this challenge, open transmission electron microscopy (TEM) was applied to thin gel films permeated by a nonvolatile ionic liquid. The targeted physical gels were prepared by cooling concentrated solutions of poly(ethylene glycol) in 1-ethyl-3-methyl imidazolium ethyl sulfate [EMIM][EtSO 4 ]. During the cooling, gelation occurred by a frustrated crystallization of the dissolved polymer, leading to a percolated, solvent-permeated semicrystalline network in which nanoscale polymer crystals acted as crosslinks. Crystalline features ranging from ~5 to ~200 nm were observed, with the visible network strands dominantly consisting of long curvilinear crystallites of ~15–20 nm diameter. Nascent spherulites irregularly decorated the network, creating a complex structural hierarchy that complicated analyses. Lacking diffraction contrast, TEM did not visualize the many disordered, fully solvated PEG chains present in the voids between crystals. Finally, recognizing that a network's three dimensionality is ambiguous when assessed through two-dimensional microscopy projections, a small gel region was studied by TEM tomography, revealing a nearly isotropic three-dimensional arrangement of the curvilinear crystallites, which displayed remarkably uniform cylindrical cross sections.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chiral Electrokinetic Phenomena in Single Nanopores

Abstract The arrangement of solvent molecules and ions at solid–liquid interfaces determines electrochemical properties that are important in separations platforms, sensing technologies, and energy‐storage systems. Here we show that single glass and polymer pores in contact with propylene carbonate (PC) solutions of LiClO 4 exhibit an effective surface potential that is modulated by the enantiomeric excess of the solvent. In particular, electrochemical and electrokinetic measurements of ionic transport through glass pipettes and polymer pores reveal that the effective surface potential is significantly lower in solutions prepared using enantiomerically pure PC than in solutions prepared using racemic PC. Both pore systems became positively charged in all racemic solutions examined in the range of LiClO 4 concentrations between 1 mM and 100 mM, whereas solutions in ( R )‐(+)‐PC induced a positive surface potential only at concentrations above ~5 mM. The effective surface potential is quantified through asymmetry in current–voltage curves and zeta‐potential measurements. Vibrational sum‐frequency‐generation experiments on LiClO 4 solutions in racemic and enantiomerically pure PC indicate that the surface lipid‐bilayer‐like region in the former is more strongly organized than in the latter, dictating the favorable positions for lithium and perchlorate ions in each case. The more ordered molecular packing in the racemic liquid leads to accumulation of lithium ions on the outside of the bilayer, creating a higher effective positive charge. Our results highlight the extreme sensitivity of the interfacial potential on molecular organization of the solvent, and the relatively unexplored role that chirality can play in electrokinetic phenomena.

Alanis, Kristen↗
DOE OSTI2025

Influences of Alkali Metal Cation Interactions on N2 Coordination to Iron(I) Beta-Diketiminate Complexes in Electrolyte Solutions

N2 functionalization reactions often use stable, isolable N2-bound complexes and low temperatures or highly activated reagents. However, little work has focused on systems where N2 binds weakly, and the N2 binding equilibrium can be modulated. Here, we describe analysis of surprising trends in alkali metal cation solvation on the formation of an anionic iron(I) beta-diketiminate complex and the subsequent N2 binding equilibrium. Variable temperature UV-vis spectroscopy shows that increased ionic strength in the coordinating solvent tetrahydrofuran promotes N2 coordination. Additionally, less solvated alkali metal cations in noncoordinating 2-methyltetrahydrofuran (MeTHF) stabilize N2 coordination, likely through the formation of contact ion pairs in solution that have enhanced N2 binding. Ionic strength has little effect on the energetics of N2 coordination to these proposed contact ion pairs in MeTHF. When the electrochemical analysis is done at –78 °C, there is an irreversible reduction of iron(II) and an anodically shifted oxidation, which is attributed to the formation of the spectroscopically observed N2 complex. Finally, bulk electrolysis is used to verify the electrochemical formation of the N2-bound anionic iron(I) complex. These studies demonstrate a new strategy for promoting N2 coordination by changing solution properties, which is relevant to homogeneous electrochemical N2 reduction methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Elucidating the Microscale Behavior and Phase Separation Kinetics of Thermally Responsive Ionic Liquid–Water Mixtures

Thermally responsive ionic liquids (ILs) exhibit liquid-liquid phase separation into a water-rich (WR) and ionic-liquid-rich (ILR) phase when heated above a lower critical solution temperature (LCST). This phase behavior has been leveraged for applications ranging from forward osmosis (FO) desalination, where the IL acts as a draw solute, to refrigeration and dehumidification cycles, where the IL acts as a liquid desiccant. While significant effort has been devoted to characterizing the thermodynamic and thermophysical properties of LCST ILs, their phase separation kinetics have not been investigated. In this work, we describe the macroscale phase separation kinetics (phase separation time) by gleaning insight into the microscale colloidal behavior of aqueous mixtures of four different materials, P 4444 TFA (tetrabutylphosphonium-2,4-trifluoroacetate), P 4444 DMBS (tetrabutylphosphonium-2,4-dimethyl-benzenesulfonate), N 4444 Sal (tetrabutylammonium salicylate), and P 4444 Sal (tetrabutylphosphonium salicylate) as a function of IL concentration at a separation temperature of 70 °C. We report the discontinuous microscale size distributions for each material and correlate their theoretical settling velocities to experimental phase separation times. The results indicate that a simple Stokes' law model can predict the phase separation time within reasonable accuracy. Overall, this work lays the foundation for understanding the micro- to macroscale phase separation behavior and kinetics of LCST ILs for various water-energy applications.

LCST↗
DOE OSTI2021

Redox-Active Polymers Designed for the Circular Economy of Energy Storage Devices

Electrochemical energy storage is a keystone to support the rapid transition to a low-carbon-emission future for grid storage and transportation. While research on electrochemical energy storage devices has mostly dealt with performance improvements (energy density and power density), little attention has been paid to designing devices that can be recycled with low cost and low environmental impact. Thus, next-generation energy storage devices should also address the integration of recyclability into the device design. In this study, we demonstrate recyclable energy storage devices based on solution-processable redox-active conjugated polymers. The high electronic and ionic charge transport in these polymers enables the operation of single-phase electrodes in aqueous electrolytes with C-rates >100 with good electrochemical stability when the cell is charged to 1.2 V. Finally, we demonstrate the recyclability of these devices, achieving >85% capacity retention in each recycling step. Our work provides a framework for developing recyclable devices for sustainable energy storage technologies.

25 ENERGY STORAGE↗
DOE OSTI2020

99 TcO 4 - removal from legacy defense nuclear waste by an alkaline-stable 2D cationic metal organic framework

Removal of 99 TcO 4 - from legacy defense nuclear tank waste at Savannah River Site is highly desirable for the purpose of nuclear safety and environmental protection, but currently not achievable given the extreme conditions including high alkalinity, high ionic strength, and strong radiation field. Herein, we present a potential solution to this long-term issue by developing a two-dimensional cationic metal organic framework SCU-103, showing ultrahigh stability in alkaline aqueous media and great resistance to both β and γ radiation. More importantly, it is very effective for 99 TcO 4 - separation from aqueous media as demonstrated by fast exchange kinetics, high sorption capacity, and superior selectivity, leading to the successful removal of 99 TcO 4 - from actual Savannah River Site high level tank waste for the first time, to the best of our knowledge. In addition, the uptake mechanism is comprehensively elucidated by molecular dynamics simulation and density functional theory calculation, showing a unique chemical recognition of anions with low charge density.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2025

Spatiotemporal dynamics of ionic reorganization near biological membrane interfaces

Electrical signals in excitable cells involve spatially localized ionic fluxes through ion channels and pumps on cellular lipid membranes. Common approaches to understand how these fluxes spread assume that the membrane and the surrounding electrolyte comprise an equivalent circuit of capacitors and resistors, which ignores the localized nature of transmembrane ion transport, the resulting ionic gradients and electric fields, and their spatiotemporal relaxation. Here, we consider a model of localized ion pumping across a lipid membrane, and use theory and simulation to investigate how the electrochemical signal propagates spatiotemporally in and out of plane along the membrane. The localized pumping generates long-ranged electric fields with three distinct scaling regimes along the membrane: a constant potential near-field region, an intermediate monopolar region, and a far-field dipolar region. Upon sustained pumping, the monopolar region expands radially in plane with a steady speed that is enhanced by the dielectric mismatch and the finite thickness of the lipid membrane. For unmyelinated lipid membranes in physiological settings, we find remarkably fast propagation speeds of ∼ 40 m / s , allowing faster ionic reorganization compared to bare diffusion. Together, our paper shows that transmembrane ionic fluxes induce transient long-ranged electric fields in electrolyte solutions, which may play hitherto unappreciated roles in biological signaling. Published by the American Physical Society 2025

Row, Hyeongjoo (ORCID:000000033623512X)↗
NASA NTRS2011

Oxygen Extraction from Regolith Using Ionic Liquids

An important concern with long-duration manned space travel is the need to furnish enough materials to the vehicle, as well as the crew, for the duration of the mission. By extracting oxygen from the oxides present in regolith, propellant and life support could be supplied to the vehicle and the crew while in space, thereby limiting the amount of supplies needed prior to lift-off. Using a class of compounds known as ionic liquids, we have been able to lower the electrolysis operating temperature from 1600 C (molten oxide electrolysis) to less than 200 C, making this process much more feasible in terms of energy consumption and materials handling. To make this process ready for deployment into space, we have investigated what steps of the process would be affected by the low-gravity environment in space. In the lab, the solubilization of lunar regolith simulant in ionic liquid produces water vapor that is normally distilled out of solution and subsequently electrolyzed for oxygen production. This distillation is not possible in space, so we have tested a method known as pervaporation and have suggested a way this technique could be incorporated into a reactor design.

Barrios, Elizabeth A.↗
DOE OSTI2024

Mechanical and Ionic Characterization for Organic Semiconductor–Incorporated Perovskites for Stable 2D/3D Heterostructure Perovskite Solar Cells

Hybrid metal halide perovskite (MHP) materials, while being promising for photovoltaic technology, also encounter challenges related to material stability. Combining 2D MHPs with 3D MHPs offers a viable solution, yet there is a gap in the understanding of the stability among various 2D materials. The mechanical, ionic, and environmental stability of various 2D MHP ligands are reported, and an improvement with the use of a quater-thiophene-based organic cation (4TmI) that forms an organic-semiconductor incorporated MHP structure is demonstrated. It is shown that the best balance of mechanical robustness, environmental stability, ion activation energy, and reduced mobile ion concentration under accelerated aging is achieved with the usage of 4TmI. It is believed that by addressing mechanical and ion-based degradation modes using this built-in barrier concept with a material system that also shows improvements in charge extraction and device performance, MHP solar devices can be designed for both reliability and efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

Surface Reactivity Analysis of the Crude Oil–Brine–Limestone Interface for a Comprehensive Understanding of the Low-Salinity Waterflooding Mechanism

Low-salinity waterflooding (LSWF) has proven to improve oil recovery in carbonate formations through rock wettability alteration, although the underlying mechanism remains elusive. Multivalent ionic exchange and calcite dissolution have usually been investigated using geochemical analysis in secondary coreflooding. In this work, coreflooding, in tertiary mode, coupled with a surface reactivity analysis approach was employed to investigate the interplay of wettability alteration mechanisms such as mineral dissolution, electrostatic bond attraction, and the effect of pH at in situ conditions. Improved oil recovery (IOR) in tertiary mode observed by coreflooding in Indiana limestone rocks showed an ionic strength dependence, that is, reducing brine ionic strength resulted in an increase in oil recovery. Coreflooding results showed that the seawater and low-salinity brines deprived of Mg 2+ ions resulted in the lowest IOR in tertiary mode, indicating the significance of Mg 2+ on IOR in limestone rocks. Similar results were observed through the contact angle measurement showing the limestone rock wettability state dependence on ionic strength and the effect of Mg2+ ions. Surface reactivity analysis showed an increase in solution pH, Ca 2+ and Mg 2+ ions concentration in the effluent solution from the coreflooding in tertiary mode using low salinity brines (about 40 and 20% increase in the effluent composition for Ca 2+ and Mg 2+ , respectively). These changes in solution composition were used to calculate the in situ oil–brine and rock–brine zeta potential using a validated surface complexation model, showing the changes of zeta potential as brine is injected into limestone rocks. The results show that using seawater-like brine in tertiary mode resulted in no mineral dissolution or ionic exchange. However, improved oil recovery (IOR) using such seawater-like brine was due to wettability alteration caused by reduced electrostatic bond attraction associated with Mg 2+ ions [from 2.6 × 10 –13 (mol/m 2 ) 2 for formation water salinity to 1.5 × 10 –13 (mol/m 2 ) 2 for seawater salinity]. Using low-salinity brines in tertiary mode improved oil recovery by mineral dissolution, resulting in oil desorption and an increase in solution pH. Finally, the increase in solution pH also resulted in reduced electrostatic bond attraction which lead to rock wettability alteration using low-salinity brines.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Salt and ion transport in a series of crosslinked AMPS/PEGDA hydrogel membranes

Salt permeability and ionic conductivity are critical properties for membranes in water purification and energy applications. Both properties depend on individual ion sorption and diffusion coefficients, which are significantly influenced by polymer chemical and physical parameters such as fixed charge concentration and membrane water content. However, systematic studies connecting polymer structure to ion transport properties are still lacking. In this study, a series of uncharged and charged membranes were synthesized using poly(ethylene glycol) diacrylate (PEGDA) as a cross-linker and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) as a charged monomer. Membrane fixed charge concentration and water uptake were systematically varied by adjusting AMPS content in the pre-polymerization mixture. Salt sorption and permeability coefficients and ionic conductivity of these membranes were measured as a function of NaCl solution concentration (0.01–1 M). Combining the solution-diffusion model and Nernst-Planck equation, individual ion diffusion coefficients were calculated. Experimental Na + diffusion coefficients for all materials were well described by the Mackie and Meares tortuosity model, highlighting the strong influence of water content on ion diffusivity in both uncharged and charged polymers. Model predictions for Cl – diffusion coefficients agree reasonably well with experimental values, with some deviations occurring in more highly charged membranes. Finally, this discrepancy might result from interactions not captured by the Mackie and Meares model (e.g., fixed charge-ion interactions).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Final Technical Report: Transport of Complex Mixtures in Ion-Containing Polymer Membranes

Permselective ion-containing membranes are an integral component for many applications from water treatment, fuel cells, and solar fuels devices where the selective transport of molecules and ions is desired. In solar fuels devices, ion-containing polymer membranes are responsible for permitting selective transport of ions between electrodes to maintain overall charge neutrality yet limit transport of reaction products produced at the electrodes. While the transport of single solutes through such membranes has been fairly well described, binary and multicomponent transport is poorly understood due to the myriad of interactions that occur in these systems (i.e. between co-permeants and between permeants and the membrane). Solar fuels devices are just one example of an application where understanding the transport of multiple simultaneous species is critically important to improving device performance as product crossover leads to reductions in overall device performance. The objectives of this research was to improve our understanding of the complex array of factors that influence transport behavior of multiple solutes within ion-containing polymer membranes. This experimental project addressed the lack of fundamental understanding of multicomponent transport behavior by synthesizing ion exchange membranes with varied incorporation of comonomers (ionic and neutral moieties) to investigate fundamental relationships between membrane structure, membrane physiochemical properties, and transport behavior of solutes and complex solute mixtures through dense, hydrated membranes.

25 ENERGY STORAGE↗
DOE OSTI2026

Ionic Liquids for Direct Air Capture of CO 2 using Electric‐Field‐Mediated Moisture Gradient Process (Final Technical Report)

The final report provides executive summary, a list of publications, and information on training graduate students and postdoctoral researchers. We carried out computational and experimental research on understanding molecular-level mechanism of how CO 2 is absorbed in a solution containing ethylene glycol as the solvent and KOH as the salt in the presence of ionic liquids and under the influence of electric field. In doing so, we developed an automated high-throughput method which allowed us to measure the solubility of CO 2 in a large number of ionic liquids, considerably speeding up the CO 2 solubility measurement. We also demonstrated how varying the concentration of ionic liquids in ethylene glycol can result in a maximum in ionic conductivity. Reaction of CO 2 and subsequent release results in a 50% reduction when the process is operated at an ionic liquid-ethylene glycol concentration yielding maximum ionic conductivity amongst all the ionic liquid-ethylene glycol combinations studied as a part of this research. We utilized machine learning models to identify unique ionic liquid-solvent combinations with ionic conductivity much higher than that measured for ionic liquid-ethylene glycol combinations. We demonstrated that the rate of CO 2 reaction with KOH in ethylene glycol can be optimized with the type of ionic liquid and its concentration. Overall, the research led to publication of 10 peer-reviewed research articles and several presentations at national conferences. We are also in the process of developing additional manuscripts based on the research carried out as a part of this project. Two graduate students and two postdoctoral researchers were supported on the funding.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Tailoring Chemical Absorption-Precipitation to Lower the Regeneration Energy of a CO 2 Capture Solvent

Solvent-based CO 2 capture consumes significant amounts of energy for solvent regeneration. To improve energy efficiency, this study investigates CO 2 fixation in a solid form through solvation, followed by ionic self-assembly-aided precipitation. Based on the hypothesis that CO 3 2- ions may bind with monovalent metal ions, we introduced Na + into an aqueous hexane-1,6-diamine solution where CO 2 forms carbamate and bicarbonate. Then, Na + ions in the solvent act as a seed for ionic self-assembly with diamine carbamate to form an intermediate ionic complex. The recurring chemical reactions lead to the formation of an ionic solid from a mixture of organic carbamate/carbonate and inorganic sodium bicarbonate (NaHCO 3 ), which can be easily removed from the aqueous solvent through sedimentation or centrifugation and heated to release the captured CO 2 . Mild-temperature heating of the solids at 80–150 °C causes decomposition of the solid CO 2 -diamine-Na molecular aggregates and discharge of CO 2 . This sorbent regeneration process requires 6.5–8.6 GJ/t CO 2 . It was also found that the organic carbamate/carbonate solid, without NaHCO 3 , contains a significant amount of CO 2 , up to 6.2 mmol CO 2 /g-sorbent, requiring as low as 2.9–5.8 GJ/t CO 2 . In conclusion, molecular dynamic simulations support the hypothesis of using Na + to form relatively less stable, yet sufficiently solid, complexes for the least energy-intensive recovery of diamine solvents compared to bivalent carbonate–forming ions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Critical Role of Anion–Solvent Interactions for Dynamics of Solvent-in-Salt Solutions

Most polar solvent molecules are unstable toward electrode materials used in Li-based batteries. Solid electrolytes and ionic liquids are far more stable; however, they have relatively low conductivity, and therefore electrical energy storage devices based on them would suffer from low power. Solvent-in-salt (SIS) systems combine chemical stability with relatively high conductivity. Here, we show how the nature of the employed anion affects the structure and dynamics of SIS systems. The transport of ions in lithium bis(fluorosulfonyl)imide (Li-FSI) systems was determined to be always faster than that in lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI) systems. Moreover, we found that viscosity does not solely control conductivity and that the lower conductivity of TFSI – solutions is related to their stronger interaction with the solvent. This restricts solvent dynamics and slows down ion motions compared to that of FSI – . Interestingly, the TFSI–solvent interaction also leads to better charge separation (weaker ion–ion correlations) and a higher transference number for Li. Finally, our results suggest that the ability to tune the solvent network formed around the anions may further improve electrolyte conductivity and Li transference number for safer and more efficient energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Cyclopentadienyl coordination induces unexpected ionic Am-N bonding in an americium bipyridyl complex

Variations in bonding between trivalent lanthanides and actinides is critical for reprocessing spent nuclear fuel. The ability to tune bonding and the coordination environment in these trivalent systems is a key factor in identifying a solution for separating lanthanides and actinides. Coordination of 4,4'-bipyridine (4,4'-bpy) and trimethylsilylcyclopentadienide (Cp') to americium introduces unexpectedly ionic Am-N bonding character and unique spectroscopic properties. Here we report the structural characterization of (Cp' 3 Am) 2 (μ -4,4'-bpy) and its lanthanide analogue, (Cp' 3 Nd) 2 (μ - 4,4'-bpy), by single-crystal X-ray diffraction. Spectroscopic techniques in both solid and solution phase are performed in conjunction with theoretical calculations to probe the effects the unique coordination environment has on the electronic structure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Ionic Liquid Facilitated Solvent‐Phase Polymerization of Ultrasmooth Coatings of Polycatecholamines

Mussel-inspired polycatecholamine coatings and films have proven to be versatile materials for surface modification. However, the progress of chemically modified coatings with tailored properties has been slow due to the lack of definitive evidence of their polymeric structure. Polycatecholamines form aggregates during polymerization, and their formation mechanism has been a subject of debate owing to their insolubility in traditional molecular solvents. Exploiting the capability of ionic liquids (ILs) to exhibit strong electrostatic interactions, herein, the first solution-phase polymerization approach is reported to achieve polymerization of four catecholamines – dopamine (DA), norepinephrine (NE), L-3,4-dihydroxyphenylalanine (L-DOPA), and adrenaline (AD). Kinetic control over the polymerization process in the solution phase enabled it to follow the process with 1 H NMR spectroscopy, revealing the formation of structural features of resulting complex heterogeneous and soluble polymers. The polymers are both covalent and associative in nature. Solution phase polymerization prevented the formation of large aggregates in the solution, thus facilitating the formation of coatings that are ultra-smooth and have root mean square roughness of the order of sub-nm to nm scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Self-discharge of magnesium–sulfur batteries leads to active material loss and poor shelf life

Due to its high theoretical energy density and relative abundancy of active materials, the magnesium–sulfur battery has attracted research attention in recent years. A closely related system, the lithium-sulfur battery, can suffer from serious self-discharge behavior. Until now, the self-discharge of Mg–S has been rarely addressed. Herein, we demonstrate for a wide variety of Mg–S electrolytes and conditions that Mg–S batteries also suffer from serious self-discharge. For a common Mg–S electrolyte, we identify a multi-step self-discharge pathway. Covalent S8 diffuses to the metal Mg anode and is converted to ionic Mg polysulfide in a non-faradaic reaction. Mg polysulfides in solution are found to be meta-stable, continuing to react and precipitate as solid magnesium polysulfide species during both storage and active use. Mg–S electrolytes from the early, middle, and state-of-the-art stages of the Mg–S literature are all found to enable the self-discharge. The self-discharge behavior is found to decrease first cycle discharge capacity by at least 32%, and in some cases up to 96%, indicating this is a phenomenon of the Mg–S chemistry that deserves focused attention.

25 ENERGY STORAGE↗