Results for “Jointed structures” — Page 15

NASA NTRS1984

Slant path rain attenuation and path diversity statistics obtained through radar modeling of rain structure

Single and joint terminal slant path attenuation statistics at frequencies of 28.56 and 19.04 GHz have been derived, employing a radar data base obtained over a three-year period at Wallops Island, VA. Statistics were independently obtained for path elevation angles of 20, 45, and 90 deg for purposes of examining how elevation angles influences both single-terminal and joint probability distributions. Both diversity gains and autocorrelation function dependence on site spacing and elevation angles were determined employing the radar modeling results. Comparisons with other investigators are presented. An independent path elevation angle prediction technique was developed and demonstrated to fit well with the radar-derived single and joint terminal radar-derived cumulative fade distributions at various elevation angles.

Goldhirsh, J.↗

NASA NTRS1980

Compression panel studies for supersonic cruise vehicles

Results of analytical and experimental studies are summarized for titanium, boron fiber reinforced aluminum matrix composite, Borsic fiber reinforced aluminum matrix composite, and titanium sheathed Borsic fiber reinforced aluminum matrix composite stiffened panels. The results indicate that stiffened panels with continuous joints (i.e., brazed, diffusion bonded or adhesive bonded joints) are more structurally efficient than geometrically similar panels with discrete joints (i.e., spotwelded or bolted joints). In addition, results for various types of fiber reinforced aluminum matrix stiffened panels indicate that titanium sheathed Borsic fiber reinforced aluminum matrix composite panels are the most structurally efficient. Analytical results are also presented for graphite fiber reinforced polyimide matrix composite stiffened panels and superplastically formed and diffusion bonded titanium sandwich panels.

Mcwithey, R. R.↗

NASA NTRS1995

Description of and preliminary tests results for the Joint Damping Experiment (JDX)

An effort is currently underway to develop an experiment titled joint Damping E_periment (JDX) to fly on the Space Shuttle as Get Away Special Payload G-726. This project is funded by NASA's IN-Space Technology Experiments Program and is scheduled to fly in July 1995 on STS-69. JDX will measure the influence of gravity on the structural damping of a three bay truss having clearance fit pinned joints. Structural damping is an important parameter in the dynamics of space structures. Future space structures will require more precise knowledge of structural damping than is currently available. The mission objectives are to develop a small-scale shuttle flight experiment that allows researchers to: (1) characterize the influence of gravity and joint gaps on structural damping and dynamic behavior of a small-scale truss model, and (2) evaluate the applicability of low-g aircraft test results for predicting on-orbit behavior. Completing the above objectives will allow a better understanding and/or prediction of structural damping occurring in a pin jointed truss. Predicting damping in joints is quite difficult. One of the important variables influencing joint damping is gravity. Previous work has shown that gravity loads can influence damping in a pin jointed truss structure. Flying this experiment as a GAS payload will allow testing in a microgravity environment. The on-orbit data (in micro-gravity) will be compared with ground test results. These data will be used to help develop improved models to predict damping due to pinned joints. Ground and low-g aircraft testing of this experiment has been completed. This paper describes the experiment and presents results of both ground and low-g aircraft tests which demonstrate that damping of the truss is dramatically influenced by gravity.

Bingham, Jeffrey G.↗

NASA NTRS1992

Development of a truss joint for robotic assembly of space structures

This report presents the results of a detailed study of mechanical fasteners which were designed to facilitate robotic assembly of structures. Design requirements for robotic structural assembly were developed, taking into account structural properties and overall system design, and four candidate fasteners were designed to meet them. These fasteners were built and evaluated in the laboratory, and the Hammer-Head joint was chosen as superior overall. It had a high reliability of fastening under misalignments of 2.54 mm (0.1 in) and 3 deg, the highest end fixity (2.18), the simplest end effector, an integral capture guide, good visual verification, and the lightest weight (782 g, 1.72 lb). The study found that a good design should incorporate chamfers sliding on chamfers, cylinders sliding on chamfers, and hard surface finishes on sliding surfaces. The study also comments on robot flexibility, sag, hysteresis, thermal expansion, and friction which were observed during the testing.

Parma, George F.↗

NASA NTRS1987

Structural design of an in-line bolted joint for the space shuttle solid rocket motor case segments

Results of a structural design study of an in-line bolted joint concept which can be used to assemble Space Shuttle Solid Rocket Motor (SRM) case segments are presented. Numerous parametric studies are performed to characterize the in-line bolted joint behavior as major design variables are altered, with the primary objective always being to keep the inside of the joint (where the O-rings are located) closed during the SRM firing. The resulting design has 180 1-inch studs, an eccentricity of -0.5 inch, a flange thickness of 3/4 inch, a bearing plate thickness of 1/4 inch, and the studs are subjected to a preload which is 70% of ultimate. The mass penalty per case segment joint for the in-line design is 346 lbm more than the weight penalty for the proposed capture tang fix.

Dorsey, John T.↗

NASA NTRS1989

Model reduction for flexible structures - Test data approach

A reduced model of a system is obtained by truncating part of its state variables. Hankel singular values and component costs determine which component is deleted or retained in the reduced model. In this paper Hankel singular values and component costs of a flexible structure are obtained from the resonance test data, rather than from the system matrices. Test data, besides system dynamics, include also actuators and sensors dynamics. For this reason, the reduced model obtained from test data can be far from the optimal one. In this paper the reconstruction of the flexible structure indices from the joint actuator-sensor-flexible structure indices is discussed.

Gawronski, Wodek↗

NASA NTRS1998

An Overview: NASA LeRC Structures Programs

A workshop on National Structures Programs was held, jointly sponsored by the AIAA Structures Technical Committee, the University of Virginia's Center for Advanced Computational Technology and NASA. The Objectives of the Workshop were to: provide a forum for discussion of current Government-sponsored programs in the structures area; identify high potential research areas for future aerospace systems; and initiate suitable interaction mechanisms with the managers of structures programs. The presentations covered structures programs at NASA, DOD (AFOSR, ONR, ARO and DARPA), and DOE. This publication is the presentation of the Structures and Acoustics Division of the NASA Lewis Research Center. The Structures and Acoustics Division has its genesis dating back to 1943. It is responsible for NASA research related to rotating structures and structural hot sections of both airbreathing and rocket engines. The work of the division encompasses but is not limited to aeroelasticity, structural life prediction and reliability, fatigue and fracture, mechanical components such as bearings, gears, and seals, and aeroacoustics. These programs are discussed and the names of responsible individuals are provided for future reference.

Zaretsky, Erwin V.↗

NASA NTRS2021

Latent Cure Epoxy Resins for Reliable Joints in Secondary-Bonded Composite Structures

In high-performance polymer matrix composite assemblies, adhesive bonding is generally superior to mechanical fastening in structural performance and manufacturing efficiency. However, adhesive bonds are susceptible to minute levels of contamination accumulated during assembly that can lead to unpredictable, weak bonds. Current methods of measuring bond strength are all destructive mechanical tests. To overcome these challenges, redundant load paths (e.g., mechanical fasteners) are often implemented in secondary-bonded, primary-structures, which can greatly reduce structural performance. This study investigated reformulated aerospace epoxy matrix resins with stoichiometric offset to inhibit cure of the matrix resin prior to assembly. Inhibited resins can reflow and mix across the joint interface, which eliminates the material discontinuity and forms a homogenous joint with reliable fracture properties. The goal of this study was to develop and demonstrate secondary composite assemblies that are mechanically and microscopically indistinguishable from a co-cured composite joint. This article describes the development of latent epoxy resins, the fabrication of test articles, and the mechanical properties measured from experimental joints compared with conventional, co-cured laminates. Methods of in-line quality control using and infrared spectroscopy and post-assembly forensics are also described. The final mode-II fracture toughness measured from precracked AERoBOND specimens was similar to that measured from co-cured laminates indicating that later cure epoxy materials could be a suitable replacement for secondary bonding.

Polymer-matrix composites (PMCs)↗

NASA NTRS2013

Robotic Finger Assembly

A robotic hand includes a finger with first, second, and third phalanges. A first joint rotatably connects the first phalange to a base structure. A second joint rotatably connects the first phalange to the second phalange. A third joint rotatably connects the third phalange to the second phalange. The second joint and the third joint are kinematically linked such that the position of the third phalange with respect to the second phalange is determined by the position of the second phalange with respect to the first phalange.

Ihrke, Chris A.↗

NASA NTRS2014

Robotic Finger Assembly

A robotic hand includes a finger with first, second, and third phalanges. A first joint rotatably connects the first phalange to a base structure. A second joint rotatably connects the first phalange to the second phalange. A third joint rotatably connects the third phalange to the second phalange. The second joint and the third joint are kinematically linked such that the position of the third phalange with respect to the second phalange is determined by the position of the second phalange with respect to the first phalange.

Ihrke, Chris A.↗

NASA NTRS2017

Strength Variation of Parachute Joints

A parachute joint is defined as a location where a component is sewn or connected to another component. During the design and developmental phase of a parachute system, the joints for each structural component are isolated and tested through a process called seam and joint testing. The objective of seam and joint testing is to determine the degradation on a single component due to interaction with other components; this data is then used when calculating the margin of safety for that component. During the engineering developmental phase of CPAS (Capsule Parachute Assembly System), the parachute system for the NASA Orion Crew Module, testing was completed for every joint of the six subsystems: the four parachutes (main, drogue, pilot, and FBCP [forward bay cover parachute]), the retention release bridle, and the retention panels. The number of joint tests for these subsystems totaled 92, which provides a plethora of data and results for further analysis. In this paper, the data and results of these seam and joint tests are examined to determine the effects, if any, of different operators and sewing machines on the strength of parachute joints. Other variables are also studied to determine their effect on joint strength, such as joint complexity, joint strength magnitude, material type, and material construction. Findings reveal that an optimally-run seam and joint test program could result in an increased understanding of the structure of the parachute; this should lead to a parachute built with optimal components, potentially saving system weight and volume.

Mollmann, Catherine↗

NASA NTRS1990

Spacecraft dynamics characterization and control system failure detection

Two important aspects of the control of large space structures are studied: the modeling of deployed or erected structures including nonlinear joint characteristics; and the detection and isolation of failures of the components of control systems for large space structures. The emphasis in the first task is on efficient representation of the dynamics of large and complex structures having a great many joints. The initial emphasis in the second task is on experimental evaluation of FDI methodologies using ground-based facilities in place at NASA Langley Research Center and Marshall Space Flight Center. The progress to date on both research tasks is summarized.

Vandervelde, Wallace E.↗

NASA NTRSDate not supplied

Innovations in Continuous Ultrasonic Welding of Thermoplastic Composites and Evaluation for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗

NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗

NASA NTRS1987

Space Station alpha joint bearing

Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

Everman, Michael R.↗

NASA NTRS2001

Reusable Solid Rocket Motor Nozzle Joint-4 Thermal Analysis

This study provides for development and test verification of a thermal model used for prediction of joint heating environments, structural temperatures and seal erosions in the Space Shuttle Reusable Solid Rocket Motor (RSRM) Nozzle Joint-4. The heating environments are a result of rapid pressurization of the joint free volume assuming a leak path has occurred in the filler material used for assembly gap close out. Combustion gases flow along the leak path from nozzle environment to joint O-ring gland resulting in local heating to the metal housing and erosion of seal materials. Analysis of this condition was based on usage of the NASA Joint Pressurization Routine (JPR) for environment determination and the Systems Improved Numerical Differencing Analyzer (SINDA) for structural temperature prediction. Model generated temperatures, pressures and seal erosions are compared to hot fire test data for several different leak path situations. Investigated in the hot fire test program were nozzle joint-4 O-ring erosion sensitivities to leak path width in both open and confined joint geometries. Model predictions were in generally good agreement with the test data for the confined leak path cases. Worst case flight predictions are provided using the test-calibrated model. Analysis issues are discussed based on model calibration procedures.

Clayton, J. Louie↗

NASA NTRS1992

Design of a welded joint for robotic, on-orbit assembly of space trusses

A preliminary design for a weldable truss joint for on-orbit assembly of large space structures is described. The joint was designed for ease of assembly, for structural efficiency, and to allow passage of fluid (for active cooling or other purposes) along the member through the joint. The truss members were assumed to consist of graphite/epoxy tubes to which were bonded 2219-T87 aluminum alloy end fittings for welding on-orbit to truss nodes of the same alloy. A modified form of gas tungsten arc welding was assumed to be the welding process. The joint was designed to withstand the thermal and structural loading associated with a 120-ft diameter tetrahedral truss intended as an aerobrake for a mission to Mars.

Rule, W. K.↗

NASA NTRS2016

Summary of LaRC 2-inch Erectable Joint Hardware Heritage Test Data

As the National Space Transportation System (STS, also known as the Space Shuttle) went into service during the early 1980's, NASA envisioned many missions of exploration and discovery that could take advantage of the STS capabilities. These missions included: large orbiting space stations, large space science telescopes and large spacecraft for manned missions to the Moon and Mars. The missions required structures that were significantly larger than the payload volume available on the STS. NASA Langley Research Center (LaRC) conducted studies to design and develop the technology needed to assemble the large space structures in orbit. LaRC focused on technology for erectable truss structures, in particular, the joint that connects the truss struts at the truss nodes. When the NASA research in large erectable space structures ended in the early 1990's, a significant amount of structural testing had been performed on the LaRC 2-inch erectable joint that was never published. An extensive set of historical information and data has been reviewed and the joint structural testing results from this historical data are compiled and summarized in this report.

Dorsey, John T.↗