SEARCH · Search NASA

Results for “LIFTING BODY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Orbit on demand - Will cost determine best design?

Eleven design concepts for vertical (V) and horizontal (H) take-off launch-on-demand manned orbital vehicles are discussed. Attention is given to up to three stages, Mach numbers (sub-, 2, or 3), expendable boosters, drop tanks (DT), and storable (S) or cryogenic fuels. All the concepts feature lifting bodies with circular cross-section and most have a 7 ft diam, 15 ft long payload bay as well as a crew compartment. Expendable elements impose higher costs and in some cases reduce all-azimuth launch capabilities. Single-stage vehicles simplify the logistics whether in H or V configuration. A two-stage H vehicle offers launch offset for the desired orbital plane before firing the rocket engines after take-off and subsonic acceleration. A two-stage fully reusable V form has the second lowest weight of the vehicles studied and an all-azimuth launch capability. Better definition of the prospective mission requirements is needed before choosing among the alternatives.

Macconochie, J. O.↗

NASA NTRS1985

Transitional, hypervelocity aerodynamic simulation and scaling in light of recent flight data

Simulation and scaling procedures applicable to maneuvering vehicles for the transitional hypervelocity flow regime are discussed with reference to certain discrepancies between lifting reentry flight data and predicted results. Low-density hypervelocity wind-tunnel data are compared with CFD and in-flight measurements. A general correlation parameter for transitional flow is produced by incorporation of a new geometric term into a form of Reynolds number. It is shown that normalized drag coefficients of a variety of shapes, including spheres, blunt-nosed cones, lifting bodies, and an STS orbiter are correlated by the parameter. A provisional bridging formula for the coefficients is presented.

Potter, J. L.↗

NASA NTRS1986

High speed viscous flow calculations about complex configurations

Applications of the NASA Ames Parabolized Navier-Stokes (PNS) code to a variety of complex generic configurations is presented. The algorithm, boundary conditions, initial conditions, and grid generators are discussed as applied to these configurations. The PNS code was used as the mainline procedure to numerically simulate the viscous supersonic flow over these generic configurations. The turbulence model that was used in this study is the Baldwin-Lomax model. The boundary conditions are the usual viscous no slip at the wall, and a characteristic procedure is used to fit the bow shock wave which is the outermost boundary. An elliptic grid generator is employed to discretize the flow domain. In addition, an equilibrium air capability has been incorporated into the code. It uses the curve fits of Tannehill, et al. The flow regimes vary from a Mach number of 2 up to 25. Both laminar and turbulent flow are considered. Varying angles of attack have also been computed. Configurations vary from simple cone-type bodies to lifting winged bodies, such as the space shuttle or the generic supersonic cruise fighter.

Chaussee, D. S.↗

NASA NTRS1987

A survey of aerobraking orbital transfer vehicle design concepts

The five existing design concepts of the aerobraking orbital transfer vehicle (namely, the raked sphere-cone designs, conical lifting-brake, raked elliptic-cone, lifting-body, and ballute) are reviewed and critiqued. Historical backgrounds, and the geometrical, aerothermal, and operational features of these designs are reviewed first. Then, the technological requirements for the vehicle (namely, navigation, aerodynamic stability and control, afterbody flow impingement, nonequilibrium radiation, convective heat-transfer rates, mission abort and multiple atmospheric passes, transportation and construction, and the payload-to-vehicle weight requirements) are delineated by summarizing the recent advancements made on these issues. Each of the five designs are critiqued and rated on these issues. The highest and the lowest ratings are given to the raked sphere-cone and the ballute design, respectively.

Park, Chul↗

NASA NTRS1987

Transition to space - A history of 'space plane' concepts at Langley Aeronautical Laboratory 1952-1957

The supersonic speeds of X-series aircraft and wind tunnel data in the early 1950s demonstrated that hypersonic flight was an achievable goal. A blunt-nosed vehicle was found to form a bow shock that deflected much of the heating an aircraft would otherwise experience at high speeds. It was felt that critical aspects of hypersonic flight, e.g., aerodynamic performance and heating, controllability, etc., could not be fully explored in wind tunnels. The X-15 project was initiated by NASA in 1954 to produce a vehicle capable of Mach 7 flight to altitudes that would permit short evaluations of human performance in microgravity. Design tradeoffs examined in the program are discussed, with emphasis on lifting bodies and winged vehicles with high L/D ratios. Political pressures created by the public triumph of the Sputnik in 1958 removed much of the impetus for development of a manned spaceplane, and long-term goals that eventually led to the Shuttle were delayed by a short-term program oriented toward ballistic manned capsules.

Hansen, James R.↗

NASA NTRS1988

Prediction of time-dependent fuselage pressures in the wake of a helicopter rotor

A method is described for the analysis of the unsteady, incompressible potential flow associated with a helicopter. The fuselage, rotor, and rotor wake are considered together in forward flight. This method is particularly useful in low advance ratio flight due to the contribution of the deformed wake to the airloads imposed on the fuselage. The rotor geometry is prescribed and the unsteady wake geometry is computed from the local flow perturbation velocities. The fuselage is modeled as a non-lifting body of source panels and the rotor and its wake are modeled as a full vortex lattice. The rotor geometry is arbitrary and several rotor blades can be represented. The unsteady airloads are computed in the presence of the deformed rotor wake by a time-stepping technique. The wake is started impulsively from rest, allowing a natural convection of the wake with time.

Berry, John D.↗

NASA NTRS1989

Aerodynamic characteristics of proposed assured crew return capability (ACRC) configurations

The aerodynamic characteristics of seven reentry configurations suggested as possible candidate vehicles to return crew members from the U.S. Space Station Freedom to earth has been reviewed. The shapes varied from those capable of purely ballistic entry to those capable of gliding entry and fromk parachute landing to conventional landing. Data were obtained from existing (published and unpublished) sources and from recent wind tunnel tests. The lifting concepts are more versatile and satisfy all the mission requirements. Two of the lifting shapes studied appear promising - a lifting body and a deployable wing concept. The choice of an ACRC concept, however, will be made after all factors involving transportation from earth to orbit and back to earth again have been weighed.

Ware, George M.↗

NASA NTRS1989

Integration of scramjets with waverider configurations

This paper presents a parametric study of a scramjet propulsion system integrated into a waverider lifting-body configuration. The analysis explores the effect of inlet geometry, internal cross-section-area distribution of the combustor section, the distribution of the heat release of the reacting mixture, the heat transfer, and the friction on the performance of the propulsion system. The Mach number, temperature, and pressure distributions within the scramjet model are studied parametrically, and the effects on the thrust are obtained. The results provide insight on the design concepts and problems that might arise for a given internal-flow configuration.

Rasmussen, M. L.↗

NASA NTRS1990

Preliminary Subsystem Designs for the Assured Crew Return Vehicle (ACRV), volumes 1-3

A long term manned facility in space must include provisions for the safety of the crew. The resolution of this need was the design of an Assured Crew Return Vehicle (ACRV). The main focus is on the braking and landing system of the ACRV. This subsystem of the ACRV was divided into three phases. The Phase 1 analysis showed that the use of a tether to aid in the reentry of the ACRV was infeasible due to cost and efficiency. Therefore, a standard rocket would be used for reentry. It was also found that the continental United States was an achievable landing site for the ACRV. The Phase 2 analysis determined the L/D of the vehicle to be 1.8, thus requiring the use of a lifting body for reentry. It was also determined that shuttle tiles would be used for the thermal protection system. In addition, a parachute sequence for further deceleration was included, namely a ringslot drogue chute, a pilot chute, and finally a ringsail main parachute. This sequence was found to be capable of slowing the vehicle to a descent velocity of 9 to 10 m/s, which is the required velocity for aerial recovery. The Phase 3 analysis proved that a Sikorsky CH-53E helicopter is capable of retrieving the ACRV at 5.5 km altitude with minimal g-forces induced on the ACRV and minimal induced moments on the helicopter upon hookup. The helicopter would be modified such that it could stabilize the ACRV close to the bottom of helicopter and carry it to the nearest designated trauma center.

Source record↗

NASA NTRS1990

Assured Crew Return Vehicle flowfield and aerodynamic characteristics

A lifting body has been proposed as a candidate for the Assured Crew Return Vehicle which will serve as crew rescue vehicle for the Space Station. The focus of this work is on body surface definition, surface and volume grid definition, and the computation of inviscid flowfields about the vehicle at wind-tunnel conditions. Very good agreement is shown between the computed aerodynamic characteristics of the vehicle at a freestream Mach number of 10 and those measured in wind-tunnel tests.

Weilmuenster, K. James↗

NASA NTRS1990

Predicted aerodynamics for a proposed personnel launch vehicle

The Langley Aerothermodynamic Upwind Relaxation Algorithm has been modified to compute equilibrium flows over shapes at hypersonic velocities. As an initial test of the modified code, solutions were obtained for a paraboloid at Mach 6 wind-tunnel test conditions in CF4 gas and at Mach 16.85 flight conditions in equilibrium air that approximated the normal shock density ratio for the experimental test. Solutions for a lifting-body concept that is proposed for a Personnel Launch System were compared with test results at Mach 6 in CF4 over an angle-of-attack range of 15 to 35 deg and with results for nominal entry flight conditions at Mach 15.

Greene, Francis A.↗

NASA NTRS1991

Stability of a non-orthogonal stagnation flow to three dimensional disturbances

A similarity solution for a low Mach number nonorthogonal flow impinging on a hot or cold plate is presented. For the constant density case, it is known that the stagnation point shifts in the direction of the incoming flow and that this shift increases as the angle of attack decreases. When the effects of density variations are included, a critical plate temperature exists; above this temperature the stagnation point shifts away from the incoming stream as the angle is decreased. This flow field is believed to have application to the reattachment zone of certain separated flows or to a lifting body at a high angle of attack. Finally, the stability of this nonorthogonal flow to self similar, 3-D disturbances is examined. Stability properties of the flow are given as a function of the parameters of this study; ratio of the plate temperature to that of the outer potential flow and angle of attack. In particular, it is shown that the angle of attack can be scaled out by a suitable definition of an equivalent wavenumber and temporal growth rate, and the stability problem for the nonorthogonal case is identical to the stability problem for the orthogonal case.

Lasseigne, D. G.↗

NASA NTRS1990

Personnel Launch System definition

A lifting-body Personnel Launch System (PLS) is defined for assured manned access to space for future U.S. space missions. The reusable craft described is configured for reliable and safe operations, maintainability, affordability, and improved operability, and could reduce life-cycle costs associated with placing personnel into orbit. Flight simulations show the PLS to be a very flyable vehicle with very little control and propellant expenditure required during entry. The attention to crew safety has resulted in the design of a system that provides protection for the crew throughout the mission profile. However, a new operations philosophy for manned space vehicles must be adopted to fully achieve low-cost, manned earth-to-orbit transportation.

Piland, William M.↗

NASA NTRS1990

A flight experiment to measure rarefied-flow aerodynamics

A flight experiment to measure rarefied-flow aerodynamics of a blunt lifting body is being developed by NASA. This experiment, called the Rarefied-Flow Aerodynamic Measurement Experiment (RAME), is part of the Aeroassist Flight Experiment (AFE) mission, which is a Pathfinder design tool for aeroassisted orbital transfer vehicles. The RAME will use flight measurements from accelerometers, rate gyros, and pressure transducers, combined with knowledge of AFE in-flight mass properties and trajectory, to infer aerodynamic forces and moments in the rarefied-flow environment, including transition into the hypersonic continuum regime. Preflight estimates of the aerodynamic measurements are based upon environment models, existing computer simulations, and ground test results. Planned maneuvers at several altitudes will provide a first-time opportunity to examine gas-surface accommondation effects on aerodynamic coefficients in an environment of changing atmospheric composition. A description is given of the RAME equipment design.

Blanchard, Robert C.↗

NASA NTRS1991

In-flight simulation at the NASA Dryden Flight Research Facility

An account of the in-flight simulation at the Dryden Flight Research Facility is presented and various aircraft and tests performed are discussed. In-flight simulation has been utilized for a variety of flying quality investigations including low-lift-to-drag ratio approach characteristics for vehicles like the X-15, the lifting bodies, and the Space Shuttle. Consideration is given to the effects of time delays on controllability of aircraft with digital flight-control systems, flight control systems for such aircraft as the X-29, and the causes and cures of pilot-induced oscillation in diverse aircraft.

Shafer, Mary F.↗

NASA NTRS1991

Utilization of simulation tools in the HL-20 conceptual design process

The role of simulations in the design of the HL-20, the crew-carrying unpowered lifting-body component of the NASA Personnel Launch System, is reviewed and illustrated with drawings and diagrams. Detailed consideration is given to the overall implementation of a real-time simulation of the HL-20 approach and landing phase, the baseline and experimental control laws used in the flight-control system, autoland guidance and control laws (vertical and lateral steering), the control-surface mixer and actuator model, and simulation results. The simulations allowed identification and correction of design problems with respect to the position of the landing gear and the original maximum L/D ratio of 3.2.

Jackson, E. B.↗

NASA NTRS1991

Numerical analysis and simulation of an assured crew return vehicle flow field

A lifting body was proposed as a candidate for the Assured Crew Return Vehicle (ACRV) which will serve as a crew rescue vehicle for the Space Station Freedom. The focus is on body surface definition, both surface and volume grid definition, and the computation of inviscid flow fields about the vehicle at wind tunnel conditions. Very good agreement is shown between the computed aerodynamic characteristics of the vehicle at M(sub infinity) = 10 and those measured in wind tunnel tests at high Reynolds numbers.

Weilmuenster, K. James↗

NASA NTRS1992

Cell volume control at a surface for three-dimensional grid generation packages

An alternate method of calculating the cell size for orthogonality control in the solution of Poisson's 3D space equations is presented. The method provides the capability to enforce a better initial guess for the grid distribution required for boundary layer resolution. This grid point distribution is accomplished by enforcing grid spacing from a grid block boundary where orthogonality is required. The actual grid spacing or cell size for that boundary is determined by the two or four adjacent boundaries in the grid block definition, which are two dimensional grids. These two dimensional grids are in turn defined by the user using insight into the flow field and boundary layer characteristics. The adjoining boundaries are extended using a multifunctional blending scheme, with user control of the blending and interpolating functions to be used. This grid generation procedure results in an enhanced computational fluid dynamics calculation by allowing a quicker resolution of the configuration's boundary layer and flow field and by limiting the number of grid re-adaptations. The cell size specification calculation was applied to a variety of configurations ranging from axisymmetric to complex three-dimensional configurations. Representative grids are shown for the Space Shuttle and the Langley Lifting Body (HL-20).

Alter, Stephen J.↗