Search NASA⌕ Search

SEARCH · Search NASA

Results for “MIXING RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Experimental measurements of soot formation in fuel-rich homogeneous mixtures using an optical rapid compression machine

Advanced combustion strategies are necessary for the use of more environmentally sustainable fuels than traditional diesel. Alcohol fuels and alcohol/gasoline blends are of particular interest as they are readily available in the marketplace. Heavy-duty engines typically use compression ignited, conventional diesel mixing controlled combustion. Mixing controlled combustion features a non-premixed diffusion flame with a wide range of local equivalence ratios, leading to potentially high rates of soot formation. This work studies the sooting behavior of iso-octane and ethanol as a function of equivalence ratio. Measurements are carried out in a rapid compression machine (RCM) and are reported for pre-ignition conditions of 10–30 bar and temperatures of 650–800 K. Theoretical equilibrium and bulk gas temperatures are calculated for both fuels. These data are used to identify the critical equivalence ratio, the lowest equivalence ratio where soot is detected with a single-pass laser extinction diagnostic. The critical equivalence ratio for iso-octane varies between 1.82 and 1.77 for compressed pressures of 10 and 20 bar, respectively. Ethanol, sometimes considered sootless, had a critical equivalence ratio between 2.37 and 2.12 for compressed pressures of 20 and 30 bar, respectively. When characterizing soot formation by oxygenated equivalence ratio, the critical equivalence ratios for ethanol approach those of iso-octane. This suggests the oxygenated nature of alcohol fuels reduces sooting tendency, but other factors such as fuel molecular structure and morphology may play a role. It was observed that ethanol will form soot at equivalence ratios only slightly higher than iso-octane, which could have implications in mixing controlled combustion. It was seen for both fuels that soot formation is pressure sensitive, with the critical equivalence ratio being inversely proportional to compressed pressure and the rate of soot formation. Future work will investigate the sooting behavior of gasoline/ethanol blends.

02 PETROLEUM↗
DOE OSTI2023

Effect of He seeding on hydrogen isotope permeation in tungsten by H-D mixed plasma exposure

Hydrogen (H) and deuterium (D) permeation fluxes for tungsten (W) by H-D mixed plasma were studied to clarify the hydrogen isotope effect on permeation by a newly designed plasma driven permeation (PDP) device at Shizuoka University. A mixed H-D plasma was produced by introducing H and D gasses with various ratios. The atomic ratio and permeation flux in the plasma were measured during the experiments. It was found that the H:D atomic ratio in the plasma was almost proportional to the introduced H:D gas ratio. When single species of H or D was irradiated, the H permeation rate showed approximately 1.6 times as high as that of D. Under H-D mixed plasma irradiation, the highest HD permeation rate was observed when the atomic ratio of H:D in the plasma was 50:50. In addition, the effect of He seeding on H-D mixed plasma driven permeation behavior was also evaluated. The recycling of hydrogen isotopes on the upstream side was enhanced due to the formation of He bubbles near the surface, which would prevent the dissolution of hydrogen isotopes into bulk W and enhance the reflection process during plasma exposure. H and D permeation fluxes were clearly reduced by seeding He in H-D mixed plasma. At lower temperature (~723 K), the ratio of steady permeation fluxes of H and D was about 75 : 25, confirming the high permeation flux of H . These results have demonstrated a significant hydrogen isotope effect, even if He was seeded or not. As the temperature increased, H and D permeation fluxes approached unity at 923 K. Therefore,this indicates that the hydrogen isotope effect was determined by the combination of recycling / reflection at or beneath the surface, which will be controlled by the temperature during plasma exposure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Cosmogenic nuclide and solute flux data from central Cuban rivers emphasize the importance of both physical and chemical mass loss from tropical landscapes

We use 25 new measurements of in situ produced cosmogenic 26 Al and 10 Be in river sand, paired with estimates of dissolved load flux in river water, to characterize the processes and pace of landscape change in central Cuba. Long-term erosion rates inferred from 10 Be concentrations in quartz extracted from central Cuban river sand range from 3.4–189 Mg km –2 yr –1 (mean 59, median 45). Dissolved loads (10–176 Mg km –2 yr –1 ; mean 92, median 97), calculated from stream solute concentrations and modeled runoff, exceed measured cosmogenic- 10 Be-derived erosion rates in 18 of 23 basins. This disparity mandates that in this environment landscape-scale mass loss is not fully represented by the cosmogenic nuclide measurements. The 26 Al / 10 Be ratios are lower than expected for steadystate exposure or erosion in 16 of 24 samples. Depressed 26 Al/ 10 Be ratios occur in many of the basins that have the greatest disparity between dissolved loads (high) and erosion rates inferred from cosmogenic nuclide concentrations (low). Depressed 26 Al/ 10 Be ratios are consistent with the presence of a deep, mixed, regolith layer providing extended storage times on slopes and/or burial and extended storage during fluvial transport. River water chemical analyses indicate that many basins with lower 26 Al/ 10 Be ratios and high 10 Be concentrations are underlain at least in part by evaporitic rocks that rapidly dissolve. Our data show that when assessing mass loss in humid tropical landscapes, accounting for the contribution of rock dissolution at depth is particularly important. In such warm, wet climates, mineral dissolution can occur many meters below the surface, beyond the penetration depth of most cosmic rays and thus the production of most cosmogenic nuclides. Our data suggest the importance of estimating solute fluxes and measuring paired cosmogenic nuclides to better understand the processes and rates of mass transfer at a basin scale.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Hybrid Doping Strategy with High‐Entropy Cu/Fe Surface Modification and Zr Bulk Incorporation for Ni‐Rich Cathodes

A hybrid doping strategy combining Zr 4+ bulk doping with high-entropy Cu 2+ /Fe 3+ surface doping is developed to enhance the structural and interfacial stability of Ni-rich layered oxide cathodes. Cu and Fe are selectively introduced at the particle surface via a surface-selective ion-exchange process, forming a ≈15 nm Fe-rich layer while preserving the layered framework. Compared to the pristine cathode, the hybrid sample exhibits significantly improved electrochemical performance in both half-cell and full-cell configurations. In half-cells, the hybrid retains 88.5% and 90.2% after 100 cycles at 1C under 4.6 and 4.5 V, respectively. During high-voltage full-cell cycling, the hybrid cathode maintains over 80% capacity retention, whereas the pristine counterpart retains less than 10% under identical conditions over the same cycling period. XPS, EELS, and DEMS analyses confirm improved oxygen retention, suppressed gas evolution, and stable surface chemistry, while DFT calculations indicate enhanced Me–O bonding in the selected Fe 0.75 Cu 0.25 (Mn 1/16 Co 2/16 Ni 13/16 )O 2 surface composition, which is identified through DFT-calculated mixing energy reaching a minimum at this ratio, indicating the most thermodynamically favorable configuration. In conclusion, these results demonstrate the effectiveness of this hybrid doping strategy in mitigating coupled degradation pathways in Ni-rich cathodes.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Removal of Antibiotics from Swine Wastewater Using an Environmentally Friendly Biochar: Performance and Mechanisms

Antibiotics used in the swine industry to treat diseases and improve animal growth are poorly absorbed by swine and have been classified as micropollutants due to their occurrence in surface water, wastewater, and soil. This study investigated the capacity of biochar produced from eastern red cedar to remove target antibiotics that have been extensively used in the swine industry. Biochar was produced by pyrolysis from eastern red cedar at 450 °C. The sorption tests were performed by mixing biochar and a solution (1:10 ratio) containing each antibiotic in 100, 300, 600, and 900 μg L –1 concentrations. The results indicate that red cedar biochar was able to effectively remove up to 99.93% tetracycline, 96.23% oxytetracycline, 98.28% chlortetracycline, 76.4% sulfadiazine, and 78.6% sulfamethazine at the lowest concentrations. The removal efficiencies at higher concentrations declined up to 83.52, 47.23, 64.16, 69.8, and 58.4% for tetracycline, oxytetracycline, chlortetracycline, sulfadiazine, and sulfamethazine, respectively. The biochar exhibited stronger adsorption capacity for chlortetracycline and sulfamethazine compared to the other antibiotics. The likely adsorption mechanisms driving the removal of tetracyclines and sulfonamides are hydrogen-bonding and π–π electron-donor–acceptor, supported by FTIR analyses of the biochar itself. Overall, the results highlighted the potential utilization of eastern red cedar biochar for practical applications, mitigating antibiotic residues from swine wastewater in a cost-effective and environmentally friendly manner due to its relatively low pyrolysis temperature (450 °C) and sustainable repurposing of an invasive tree species.

09 BIOMASS FUELS↗
DOE OSTI2022

Reduced models for ETG transport in the tokamak pedestal

This paper reports on the development of reduced models for electron temperature gradient (ETG) driven transport in the pedestal. Model development is enabled by a set of 61 nonlinear gyrokinetic simulations with input parameters taken from pedestals in a broad range of experimental scenarios. The simulation data have been consolidated in a new database for gyrokinetic simulation data, the multiscale gyrokinetic database (MGKDB), facilitating the analysis. The modeling approach may be considered a generalization of the standard quasilinear mixing length procedure. The parameter η, the ratio of the density to temperature gradient scale length, emerges as the key parameter for formulating an effective saturation rule. With a single order-unity fitting coefficient, the model achieves an error of 15%. A similar model for ETG particle flux is also described. We also present simple algebraic expressions for the transport informed by an algorithm for symbolic regression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A Computational Investigation of Engine Heat Transfer with Ducted Fuel Injection

Ducted fuel injection (DFI) is an innovative method that curtails or prevents soot formation in direct-injection compression-ignition engines. DFI uses a simple duct, positioned outside each injector hole, facilitating the fuel/charge gas mixing before ignition. This reduces the equivalence ratio below two, in the autoignition zone, which in turn decreases soot formation. But this method also reduces fuel-conversion efficiency. This study investigates the effects of DFI on in-cylinder heat transfer. Experiments with conventional diesel combustion (CDC) and DFI were performed at four different dilution levels. Computational fluid dynamics (CFD) simulations were carried out at conditions matching those of the experiments, and the simulations were validated by the experimental data. The CFD simulations enabled to examine of in-cylinder heat release and temperature distributions. The heat transfer to the piston, head, and cylinder was investigated. The results show that DFI increased the heat transfer to the walls compared to CDC under the same conditions. This could help explain why DFI has been observed to reduce fuel-conversion efficiency by approximately 1% (absolute) relative to CDC under certain conditions. The efficiency loss typically decreases with dilution, such that DFI can improve fuel-conversion efficiencies relative to CDC at higher dilution levels.

Şener, Ramazan↗
DOE OSTI2020

Process Intensification for Nanocomposite Aluminum Extrusions: CRADA 411 (Final Report)

The project evaluated the feasibility of using Shear Assisted Processing and Extrusion (ShAPE) for the fabrication of extrusions with a diameter of 0.5” and higher from an Al-alloy powder feedstock that contains nanoscale second phases for achieving enhanced elevated temperature strength. PNNL has previously extruded 0.2” diameter rods with high strength aluminum alloy powder Al-12.4TM. This project aimed to scale the process up to a diameter of 1.0” at a length of >24” while retaining the excellent mechanical properties achieved for the 0.2” diameter rods. As part of the project, extrusion dies were fabricated with various design features. As an example, scroll features on the tool die face was introduced to enhance powder mixing, and reduce extrusion load. Varying extrusion ratios were used to obtain better microstructural homogeneity. Use of tool design features together with the optimization of process parameters helped in the fabrication of extrusions that were up to 48” long with a diameter of 0.5” using Al-12.4 TM powder feedstock in a two-step process involving cold compaction followed by extrusion. Extrusions with a diameter of 1.0” could also be fabricated, but limitations on the extent of consolidation were experienced as a result of the torque and ram force capacity of the current ShAPE machine.

36 MATERIALS SCIENCE↗
DOE OSTI2022

WECC Wide-Area Oscillation Assessment and Trending Study Report

This project, Wide-area Oscillation Analysis and Trending Study, is sponsored by the Office of Electricity (OE) of the Department of Energy (DOE) who tasked Northwest National Laboratory (PNNL) to conduct this research. Staff of Federal Energy Regulatory Commission (FERC) have been involved in the project as observers and have provided advisory comments and suggestions. The primary objective of this study is to assess whether there are significant trends in the wide-area oscillatory behavior with respect to the significant generation-mix changes brought by the increased penetration of RES in the WECC system. The work performed in this project is considered to be complimentary to previous work by NERC/industry and covers the aspects that have not been studied or trended before. The trending analysis presented in this report can serve as reference for future grid planning and operation of the WECC system. In this report, how the changes in the generation mix can impact the frequency and damping ratio (DR) of WECC wide-area oscillation modes has been studied. Thorough data-based and model-based analyses have been carried out to analyze the current trends and then extended to evaluate the oscillation behaviors of the future WECC system.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Thermogravimetric Analysis (TGA) for Carbon Fiber and Glass Fiber Epoxy Composites and their Constituents

In this work, thermogravimetric analysis (TGA) was performed on samples of a carbon fiber epoxy composite, a glass fiber epoxy composite, and a mixed carbon fiber/glass fiber epoxy composite, as well on each constituent material (polymer epoxy, carbon fibers and glass fibers). TGA was conducted for heating rates from 1-20 C/min with purified purge gases of nitrogen and dry air. For the fiberglass composite, we find that ~70% of the material remains after heating in air to 1200 C. For the carbon fiber epoxy composite, we observe greater mass loss as the carbon fibers can oxidize, leaving little material by the end of the test. The mixed composite, which has a 2:1 ratio of glass fibers to carbon fibers, experienced a total mass loss between the two other composites. By determining the relationship between the thermal decomposition of a composite material and its constituent materials, we can predict the fire behavior of novel composites during the material design phase.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Direct Ink-Write Printing of Ceramic Clay with an Embedded Wireless Temperature and Relative Humidity Sensor

This research presents a simple method to additively manufacture Cone 5 porcelain clay ceramics by using the direct ink-write (DIW) printing technique. DIW has allowed the application of extruding highly viscous ceramic materials with relatively high-quality and good mechanical properties, which additionally allows a freedom of design and the capability of manufacturing complex geometrical shapes. Clay particles were mixed with deionized (DI) water at different ratios, where the most suitable composition for 3D printing was observed at a 1:5 w/c ratio (16.2 wt.%. of DI water). Differential geometrical designs were printed to demonstrate the printing capabilities of the paste. In addition, a clay structure was fabricated with an embedded wireless temperature and relative humidity (RH) sensor during the 3D printing process. The embedded sensor read up to 65% RH and temperatures of up to 85 °F from a maximum distance of 141.7 m. The structural integrity of the selected 3D printed geometries was confirmed through the compressive strength of fired and non-fired clay samples, with strengths of 70 MPa and 90 MPa, respectively. This research demonstrates the feasibility of using the DIW printing of porcelain clay with embedded sensors, with fully functional temperature- and humidity-sensing capabilities.

42 ENGINEERING↗
DOE OSTI2022

Influence of gasoline fuel formulation on lean autoignition in a mixed-mode-combustion (deflagration/autoignition) engine

We report stoichiometric spark-ignition engines suffer efficiency penalties due to throttling losses at low loads, a low specific-heat ratio of the stoichiometric working fluid, and limits on compression ratio due to end-gas autoignition leading to undesirable knocking. Mixed-Mode Combustion (MMC) mitigates these shortcomings by using a lean working fluid where a spark-initiated pilot-stabilized deflagrative flame front is followed by controlled end-gas autoignition. This MMC study investigates the effects of initial conditions (intake air temperature, intake pressure, equivalence ratio, and intake oxygen fraction) on autoignition tendency of four gasoline-range fuels with varying properties and composition. The use of fuels with varying octane sensitivity (S) allowed exploring the importance of low-temperature heat release in triggering autoignition. Fuels with high S were less reactive for conditions that promote low-temperature chemistry (operation at high intake air pressure or without N2 dilution). Conversely, an Alkylate fuel with low S showed a greater autoignition resistance at operating conditions that were unfavorable for low-temperature chemistry. Next, the effect of residual gas composition on autoignition tendency of fuels was examined with a chemical-kinetics model. Among the various molecules in the residual gas, nitric oxide (NO) enhanced the low-temperature chemistry and increased the autoignition tendency most significantly. The fuels’ autoignition response to increasing NO amount corroborates the experimental observations. Next, the sequential autoignition of the end-gas was assessed to be less impacted by thermal stratification because of lean mixtures showing relatively less low-temperature chemistry, when compared to stoichiometric mixtures. Next, the effect of changing equivalence ratio on the autoignition was found to be similar for all fuels, regardless of their S. With changing intake air temperature, the response of fuels’ autoignition tendency depended on the dilution level used. At high dilution (i.e. low intake [O2]), fuels’ reactivity increased with increasing intake air temperature. In contrast, for operation without dilution, the autoignition tendency of the low-S Alkylate fuel decreased with increasing intake air temperature, while that of high-S High Cycloalkane fuel still increased with increasing intake air temperature. In conclusion, conventional octane metrics (RON and MON) have utility in assessing the autoignition tendency under lean MMC operation. Moreover, the fuel requirements for MMC align with that of stoichiometric operation: i.e., high RON and high S fuels are desirable for stable non-knocking operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tuning the Structural and Magnetic Properties in Mixed Cation Mn x Co 2– x P 2 S 6

The metal thiophosphates (MTP), M 2 P 2 S 6, are a versatile class of van der Waals materials, which are notable for the possibility of tuning their magnetic properties with the incorporation of different transition-metal cations. Further, they also offer opportunities to probe the independent and synergistic role of the magnetically active cation sublattice when coupled to P 2 Q 6 polyhedra. Herein, we report the structural, magnetic, and electronic properties of the series of MTPs, Mn x Co 2– x P 2 S 6 ( x = 0.25, 0.5, 1, 1.5, 1.75) synthesized by the P 2 S 5 flux method. In this work, structural and elemental analysis indicates a homogeneous stoichiometry in the Mn x Co 2– x P 2 S 6 compounds. We observe that a correlation is apparent between the intensities of specific Raman modes and Raman shifts with respect to the alloying ratio between Mn and Co. Magnetic susceptibility measurements indicate that the alloyed systems adopt an ordered antiferromagnetic (AFM) configuration with a dependence of the Néel temperature on the alloying ratio. A possible magnetic frustration behavior was observed for the composition MnCoP 2 S 6 due to magnetic moment compensation as the alloying ratio between Mn and Co approaches parity. Interestingly, mixed oxidation states of the metal cation species are also observed in Mn x Co 2– x P 2 S 6 along with a linear dependence of the work function on the alloying ratio of Mn and Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The dependence of tungsten fuzz layer thickness and porosity on tungsten deposition rate and helium ion fluence

Abstract Fuzz formation on a heated tungsten surface in the presence of a helium-containing plasma and tungsten deposition source was investigated. Tungsten samples were exposed at 1123 K to pure helium plasma with ion incident energy of 76 eV, W/He ion flux ratio of ∼ 0.4 × 10 − 4 , and varied helium ion fluence from 0.18 to 3.4 × 10 26 m −2 . Fuzz thickness was measured by cross-sectional scanning electron microscopy to increase from 0.22 to 15 µ m with increasing helium ion fluence. No indication of saturation in fuzz thickness at high fluence was observed, in contrast to fuzz produced on a tungsten surface without tungsten deposition. Additional tungsten samples were exposed at 1123 K to pure helium plasma with ion incident energy of 76 eV, helium ion fluence of ∼ 3.4 × 10 26 m −2 , and varied W/He ion flux ratio from 0.26 to 3.0 × 10 − 4 . Fuzz thickness increased from 7.5 to 120 µ m with increasing W/He ion ratio. A final sample exposed at 1123 K to a mixed helium-deuterium plasma with ion incident energy of 76 eV, helium ion fluence of 0.18 × 10 26 m −2 , and W/He ion flux ratio of 2.2 × 10 − 4 developed nearly identical fuzz structures to that developed in a pure He plasma. As a function of deposited tungsten fluence, all results were found to trace out a single layer-growth curve given by a power law relation, indicating that fuzz thickness is independent of the W/He ion flux ratio in the range investigated and independent of any deuterium present in the plasma. As a result, for tungsten plasma facing walls in magnetic fusion devices at 1000–2000 K with 10 −4 W/He ion flux ratio, fuzz with thicknesses greater than hundreds of microns may form in as little as 10 4 s (in the absence of ELM-induced erosion or annealing), and may more significantly affect its thermophysical properties than fuzz generated without a tungsten deposition source.

Physics↗
DOE OSTI2021

Comparative study with two reduced test facilities for air-cooled RCCS scaling law

Korea Atomic Energy Research Institute (KAERI) and Argonne National Laboratory (ANL) conducted steady-state tests at constant heat flux conditions to investigate the scale effect on heat removal behavior of the air-cooled Reactor Cavity Cooling System (RCCS). Two differently scaled-down test facilities were used in this study, KAERI’s ¼ scale with 4.0-m cavity height, and ANL’s ½ scale with 6.8-m cavity height. Two scaling laws were proposed to simulate the radiation across the cavity and the buoyancy-driven duct flow in the riser, respectively. The test matrix for KAERI and ANL test facilities focused on the scaling effect of the heated riser length with constant heat flux at the PMR200 RCCS design. The test results showed that mixed convection in the riser duct is an important factor for accurately extrapolating the thermo-fluid behavior in the prototype from the test results in the scale-down facilities. The system analysis code, GAMMA+, with improved heat transfer models predicted fairly well the air-cooled RCCS test data from two facilities. GAMMA+ analysis results showed that the predicted radiation fractions on the heated plate in the scale-down test conditions were larger than those on the reactor vessel in the prototype. The scaling law for air-cooled RCCS was improved by considering the mixed convection in the riser duct and the same radiation fraction on the heated plate. The mixed convection effect was calculated by the height ratio. The same radiation fraction provided a conservative extrapolation from the scale-down test results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Annual Herbaceous Plants Exhibit Altered Morphological Traits in Response to Altered Precipitation and Drought Patterns in Semiarid Sandy Grassland, Northern China

The frequency and intensity of extreme precipitation events and severe drought are predicted to increase in semiarid areas due to global climate change. Plant morphological traits can reflect plant responses to a changing environment, such as altered precipitation or drought patterns. In this study, we examined the response of morphological traits of root, stem, leaf and reproduction meristems of annual herbaceous species to altered precipitation and drought patterns in a semiarid sandy grassland. The study involved a control treatment (100% of background precipitation) and the following six altered precipitation treatments: (1) P(+): precipitation increased by 30%, (2) P(++): precipitation increased by 60%, (3) P(-): precipitation decreased by 30%, (4) P(--): precipitation decreased by 60%, (5) drought 1 (D1): 46-day drought from May 1st to June 15th, and (6) drought 2 (D2): 46-day drought from July 1st to August 15th. P(++) significantly increased root length, flower length-to-width ratio, both P(+) and P(++) significantly increased stem length and flower number in the plant growing seasons, while all of them decreased under P(-) and P(--). The annual herbaceous plants marginally increased the number of second-level stem branches and stem diameter in order to better resist the severe drought stress under P(--). P(+) and P(++) increased the root, stem, leaf, and flower dry weight, with the flower dry weight accounting for a larger proportion than the other aboveground parts. Under D2, the plants used the limited water resources more efficiently by increasing the root-to-shoot ratio compared with P(-), P(--) and D1, which reflects biomass allocation to belowground increased. The linear mixed-effects models and redundancy analysis showed that the root-to-shoot ratio and the dry weight of various plant components were significantly affected by morphological traits and altered precipitation magnitude. Our results showed that the herbaceous species have evolved morphological trait responses that allow them to adapt to climate change. Such differences in morphological traits may ultimately affect the growing patterns of annual herbaceous species, enhancing their drought-tolerant capacity in semiarid sandy grassland during the ongoing climate change.

Sun, Shan-Shan↗
DOE OSTI2020

CI-MBPT and Intensity-Based Lifetime Calculations for Th II

Lifetime calculations of Th II J = 1.5 and 2.5 odd states are performed with configuration–interaction many-body perturbation theory (CI-MBPT). For many J = 2.5 states, lifetimes are quite accurate, but two pairs of J = 2.5 odd states and many groups of J = 1.5 states are strongly mixed, making theoretical predictions unreliable. To solve this problem, a method based on intensities is used. To relate experimental intensities to lifetimes, two parameters, one an overall coefficient of proportionality for transition rates and one temperature of the Boltzmann distribution of populations, are introduced and fitted to minimize the deviation between theoretical and intensity-derived lifetimes. For strongly mixed groups of states, the averaged lifetimes obtained from averaged transition rates were used instead of individual lifetimes in the fit. Close agreement is obtained. Then intensity branching ratios are used to extract individual lifetimes for the strongly mixed states. The resulting lifetimes are compared to available directly measured lifetimes and reasonable agreement is found, considering limited accuracy of intensity measurements. The method of intensity-based lifetime calculations with fit to theoretical lifetimes is quite general and can be applied to many complex atoms where strong mixing between multiple states exists.

74 ATOMIC AND MOLECULAR PHYSICS↗