Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nickelates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Fretting of Nickel-Chromium-Aluminum Alloys at Temperatures to 816 C

A series of four nickel-based alloys containing 10 percent and 20 percent chromium in combination with 2 percent and 5 percent aluminum were fretted in dry air at temperatures to 816 C. At all temperatures, the alloys showed far less fretting wear than did high-purity nickel. This was attributed to the formation of protective oxide films on the alloys, the result of the selective oxidation of the alloy constituents. Increasing the aluminum concentration reduced fretting wear at all temperatures. Increasing the chromium concentration from 10 percent to 20 percent resulted in decreased fretting wear at 23 and 540 C, but increased fretting wear at 650 and 816 C.

Bill, R. C.↗
NASA NTRS1974

A nickel base alloy, NASA WAZ-16, with potential for gas turbine stator vane application

A nickel-base superalloy based on the nickel-aluminum-tungsten system designated WAZ-16 was developed for high strength in the 1095 C (2000 F) to 1205 C (2200 F) range. Its tensile strength at the latter temperature is approximately 186 MN/m2 (27,000 psi). The combination of properties of the alloy suggest that it has potential as a stator vane material in advanced gas turbine engines.

Waters, W. J.↗
NASA NTRS1974

Study of process variables associated with manufacturing hermetically-sealed nickel-cadmium cells

A two year study of the major process variables associated with the manufacturing process for sealed, nickel-cadmium, areospace cells is summarized. Effort was directed toward identifying the major process variables associated with a manufacturing process, experimentally assessing each variable's effect, and imposing the necessary changes (optimization) and controls for the critical process variables to improve results and uniformity. A critical process variable associated with the sintered nickel plaque manufacturing process was identified as the manual forming operation. Critical process variables identified with the positive electrode impregnation/polarization process were impregnation solution temperature, free acid content, vacuum impregnation, and sintered plaque strength. Positive and negative electrodes were identified as a major source of carbonate contamination in sealed cells.

Miller, L.↗
NASA NTRS1974

Fabrication and testing of negative-limited sealed nickel-cadmium cells

Negative-limited sealed nickel-cadmium cells are a possible means toward increasing the life of nickel-cadmium cells to about a decade or more. The purpose of this program is to design, construct, and test 100, 20 Ah and 100, 30 Ah negative-limited sealed cells. The cell design was completed and hardware was ordered during the first quarter. Electrode fabrication was started in the first quarter and carried on through the second quarter. The fabrication and selection of the necessary electrodes has been completed during the third quarter. Cell construction has been completed and the preparatory cell cycling is underway. The preliminary testing to select the initial delivery cell has been started.

Gordy, D. J.↗
NASA NTRS1974

Effects of composition and testing conditions on oxidation behavior of four cast commercial nickel-base superalloys

Four cast nickel-base superalloys were oxidized at 1000 and 1100 C for times up to 100 hr in static air and a Mach 1 gas stream. The oxidation resistance was judged by weight change, metal thickness loss, depletion-zone formation, and oxide formation and morphology. The alloys which formed mostly nickel aluminate (NiAl2O4) and aluminum oxide (Al2O3) (B-1900, VIA, and to a lesser extent 713C) were more oxidation resistant. Poorer oxidation resistance was associated with the appearance of chromium sesquioxide (Cr2O3) and chromite spinel (738X). Refractory metal content had little effect on oxidation resistance. Refractory metals appeared in the scale as tapiolite (NiM2O6, where M represents the refractory metal). Thermal cycling in static air appeared to supply sufficient data for the evaluation of oxidation resistance, especially for alloys which form oxides of low volatility. For alloys of higher chromium levels with high propensities toward forming a chromium-bearing scale of higher volatility, testing under conditions of high gas velocity is necessary to assess fully the behavior of the alloy.

Lowell, C. E.↗
NASA NTRS1974

Dispersion strengthened nickel-yttria sheet alloy produced from comminuted powders

Report on initial efforts to dispersion-strengthen nickel with Y2O3 in an attempt to replace radioactive ThO2 as the strengthening phase in dispersion-strengthened alloys. Nickel-Y2O3 powders were processed by the NASA comminution and blending (NASCAB) method and subsequently thermomechanically worked. Experimental variables included volume per cent Y2O3 (2% and 4%), powder cleaning temperature (315, 371, and 426 C), a screening step in the process, and the number (up to 23) of cold-roll-anneal cycles. Tensile strengths, determined at 1093 C, as well as some stress-rupture life data, are presented.

Sikora, P. F.↗
NASA NTRS1973

Remanent magnetization and structural effects due to shock in natural and man-made iron-nickel alloys

Explosive shock or meteorite impact are significant remagnetization processes. The mechanisms of remagnetization associated with the dynamic processes depend on the peak shock pressure, the nature of the shocked materials, and the behavior of the shock in the material. Magnetic measurements can be used to classify products formed during a shock process, and magnetic measurements can be used to investigate the process itself because of the special characteristics of the remanent magnetization vectors. The magnetic coercive force increases more rapidly in quenched and annealed iron-nickel alloys as nickel is added than it does in the alloys which have been shocked.

Wasilewski, P. J.↗
NASA NTRS1973

M553 sphere forming experiment: Pure nickel specimen evaluation

A region or cap of very fine two-dimensional surface growth structure was observed at the top of three of the six pure nickel flight specimens. Such two-dimensional surface growth structures have been observed both on the ground-based specimens and on other surface areas of the flight specimens. However, the fine structures observed on the three flight samples are at least an order of magnitude finer than those previously observed, and resemble similar localized, fine, two-dimensional surface structures observed in both ground and flight specimens for the nickel alloys. The two-dimensional growth areas consist primarily of fine equiaxed grains, specimen SL-2.6, fine dendrites, specimen SL-2.5, or a core of fine equiaxed grains surrounded by a ring of fine dendrites, specimen SL-1.9.

Johnson, P. C.↗
NASA NTRS1975

Comparison under a simulated sun of two black-nickel-coated flat-plate solar collectors with a nonselective black-paint-coated collector

A performance evaluation was made of two, black nickel coated, flat plate solar collectors. Collector performance was determined under a simulated sun for a wide range of inlet temperatures, including the temperature required for solar powered absorption air conditioning. For a basis of comparison a performance test was made on a traditional, two glass, nonselective, black paint coated, flat plate collector. Performance curves and performance parameters are presented to point out the importance of the design variables which determine an efficient collector. A black nickel coated collector was found to be a good performer at the conditions expected for solar powered absorption air conditioning. This collector attained a thermal efficiency of 50 percent at an inlet temperature of 366 K (200 F) and an incident flux of 946 watts/sq m (300 Btu/hr-sq ft).

Simon, F. F.↗
NASA NTRS1976

Improvement of black nickel coatings

Selectively absorbing black nickel coatings are among the most optically efficient low cost coatings for use on flat plate solar collectors. However, a current Ni-Zn-S-O coating in use is quite susceptible to a humid environment, degrading badly in less than ten days at 38 C (100 F) at 95 percent relative humidity. Therefore, a black nickel formula was developed which can withstand such exposures with no loss of optical efficiency, solar absorption of 0.92 and an infrared emittance (at 100 C) of 1.00 were still present after 14 days of humidity exposure. This compares to a solar absorptance of only 0.72 for the previous formula after a similar time period. The electroplating bath and conditions were changed to obtain the more stable coating configuration. The effect of bath composition, temperature, pH, and plating current density and time on the coating composition, spectral optical properties and durability were investigated systematically.

Peterson, R. E.↗
NASA NTRS1976

Low cycle fatigue life of two nickel-base casting alloys in a hydrogen environment

Samples of two nickel-base casting alloys, Mar-M-246 (a Martin Company alloy) and 713LC (a low-carbon modification of the alloy 713C developed by International Nickel Company) were tested as candidate materials for the high-pressure fuel and high-pressure oxidizer turbopump turbine nozzles. The samples were subjected to tensile tests and to low cycle fatigue tests in high-pressure hydrogen to study the influence of the hydrogen environment. The Mar-M-246 material was found to have a three times higher cyclic life in hydrogen than the 713LC alloy, and was selected as the nozzle material.

Cooper, R. A.↗
NASA NTRS1977

Fabrication and testing of large size nickel-zinc cells

The design and construction of nickel zinc cells, containing sintered nickel electrodes and asbestos coated inorganic separator materials, were outlined. Negative electrodes were prepared by a dry pressing process while various inter-separators were utilized on the positive electrodes, consisting of non-woven nylon, non-woven polypropylene, and asbestos.

Klein, M.↗
NASA NTRS1977

Nickel base alloy

A nickel base superalloy for use at temperatures of 2000 F (1095 C) to 2200 F (1205 C) was developed for use as stator vane material in advanced gas turbine engines. The alloy has a nominal composition in weight percent of 16 tungsten, 7 aluminum, 1 molybdenum, 2 columbium, 0.3 zirconium, 0.2 carbon and the balance nickel.

Freche, J. C.↗
NASA NTRS1978

Strainrange partitioning behavior of the nickel-base superalloys, Rene' 80 and in 100

A study was made to assess the ability of the method of Strainrange Partitioning (SRP) to both correlate and predict high-temperature, low cycle fatigue lives of nickel base superalloys for gas turbine applications. The partitioned strainrange versus life relationships for uncoated Rene' 80 and cast IN 100 were also determined from the ductility normalized-Strainrange Partitioning equations. These were used to predict the cyclic lives of the baseline tests. The life predictability of the method was verified for cast IN 100 by applying the baseline results to the cyclic life prediction of a series of complex strain cycling tests with multiple hold periods at constant strain. It was concluded that the method of SRP can correlate and predict the cyclic lives of laboratory specimens of the nickel base superalloys evaluated in this program.

Halford, G. R.↗
NASA NTRS1978

Nine percent nickel steel heavy forging weld repair study

The feasibility of making weld repairs on heavy section 9% nickel steel forgings such as those being manufactured for the National Transonic Facility fan disk and fan drive shaft components was evaluated. Results indicate that 9% nickel steel in heavy forgings has very good weldability characteristics for the particular weld rod and weld procedures used. A comparison of data for known similar work is included.

Young, C. P., Jr.↗
NASA NTRS1978

Effects of thermomechanical processing on strength and toughness of iron - 12-percent-nickel - reactive metal alloys at -196 C

Thermomechanical processing (TMP) was evaluated as a method of strengthening normally tough iron-12-nickel-reactive metal alloys at cryogenic temperatures. Five iron-12 nickel alloys with reactive metal additions of aluminum, niobium, titanium, vanadium, and aluminum plus niobium were investigated. Primary evaluation was based on the yield strength and fracture toughness of the thermomechanically processed alloys at -196 C.

Stephens, J. R.↗
NASA NTRS1978

Strainrange partitioning behavior of the nickel-base superalloys, Rene 80 and 100

A study has been made to assess the ability of the method of Strainrange Partitioning (SRP) to both correlate and predict high-temperature low-cycle fatigue lives of nickel-base superalloys for gas turbine applications. SRP is shown to correlate the cyclic lives of the baseline tests to within factors of nearly two. The partitioned strainrage versus life relationships for uncoated Rene 80 and cast IN 100 have also been determined from the ductility normalized-strainrange partitioning equations. These were used to predict the cyclic lives of the baseline tests. Predicted and observed cyclic lives agreed to within factors of nearly three. The life predictability of the method is also verified for cast IN 100 by applying the baseline results to the cyclic-life prediction of a series of complex strain-cycling tests with multiple hold periods at constant strain. It is concluded that the method of SRP can correlate and predict the cyclic lives of laboratory specimens of the nickel-base superalloys evaluated in this program.

Halford, G. R.↗