Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nozzle Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Preliminary static tests of a simulated upper-surface blown jet-flap configuration utilizing a full-size turbofan engine

The investigation was conducted to evaluate the static turning performance and the pressure and temperature environment of an upper-surface-blown wing and flap utilizing a small turbofan engine. The tests involved modifications of the engine primary nozzle designed to alleviate high temperature problems on the wing and flaps and yet provide acceptable static turning performance over the desired range of flap deflections and thrust conditions.

Shivers, J. P.↗
NASA NTRS1974

Effect of gaseous and solid simulated jet plumes on an 040A space shuttle launch configuration at m=1.6 to 2.2

The effect of plume-induced flow separation and aspiration effects due to operation of both orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the Space Shuttle Vehicle is determined. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold-gas jet supplied by an auxiliary 200-atm air supply system and solid-body plume simulators. The aerodynamic effects produced by these two simulation procedures are compared. The parameters most significantly affected by the jet plumes are pitching moment, elevon control effectiveness, axial force, and orbiter wing loads. The solid rocket motor (SRM) plumes have the largest effect on the aerodynamic characteristics. The effect of the orbiter plumes in combination with the SRM plumes is also significant. Variations in the nozzle design parameters and configuration changes can reduce the jet plume-induced aerodynamic effects.

Dods, J. B., Jr.↗
NASA NTRS1974

The 3.3K thrust chamber life prediction

The cause of low-cycle fatigue failure of the 3.3K Thrust Chamber was investigated. This thrust chamber typifies the current trend in rocket nozzle design which calls for high performance coupled with weight and volume limitations as well as the requirement of reusability. The analysis was performed with the BOPACE finite-element computer program which provides capability to determine viscoplastic response of a structure subjected to cyclic thermal and mechanical loading. Results are presented which show the critical region for low-cycle fatigue and the history of strain within that region for each thermo-mechanical loading cycle in the 3.3K thrust chamber. The predicted behavior was used to evaluate the low-cycle fatigue life near the throat plane of the chamber. The results show that BOPACE provides an extremely accurate prediction of structural behavior; the critical region was identified and the life determined from computed strains was within 154 cycles of the observed failure at 1013 cycles.

Armstrong, W. H.↗
NASA NTRS1976

Laser Doppler spectrometer method of particle sizing

A spectrometer for the detection of airborne particulate pollution in the submicron size range is described. In this device, airborne particles are accelerated through a supersonic nozzle, with different sizes achieving different velocities in the gas flow. Information about the velocities of the accelerated particles is obtained with a laser-heterodyne optical system through the Doppler shift of light scattered from the particles. Detection is accomplished by means of a photomultiplier. Nozzle design and signal processing techniques are also discussed.

Weber, F. N.↗
NASA NTRS1976

Three dimensional thrust chamber life prediction

A study was performed to analytically determine the cyclic thermomechanical behavior and fatigue life of three configurations of a Plug Nozzle Thrust Chamber. This thrust chamber is a test model which represents the current trend in nozzle design calling for high performance coupled with weight and volume limitations as well as extended life for reusability. The study involved the use of different materials and material combinations to evaluate their application to the problem of low-cycle fatigue in the thrust chamber. The thermal and structural analyses were carried out on a three-dimensional basis. Results are presented which show plots of continuous temperature histories and temperature distributions at selected times during the operating cycle of the thrust chamber. Computed structural data show critical regions for low-cycle fatigue and the histories of strain within the regions for each operation cycle.

Armstrong, W. H.↗
NASA NTRS1976

Results and progress on the NASA Lewis H2-O2 MHD program

A rocket test facility at the NASA Lewis Research Center has been used to develop interelectrode insulating materials, measure heat losses, and determine the fluid dynamic and electrical properties of MHD ducts and the cesium-seeded H2-O2 working fluid. Test results show that flame sprayed ceramic coatings on combustion chamber and nozzle walls permit operation with hot walls, eliminating problems associated with seed condensation; however, the net heat transfer was unexpectedly increased over that of cold copper walls. Pressure disturbances associated with oblique pressure waves were measured in a rocket nozzle designed to achieve low weight rather than perfectly parallel flow at the exit. Electrical conductivity measurements were in good agreement with theory except at low combustion pressures and/or high seed/oxygen mass flow ratios. The discrepancy is thought to result from poor atomization of the seed, producing droplets which do not completely vaporize during their residence time.

Smith, J. M.↗
NASA NTRS1978

Toward scramjet aircraft

The possibility for civil, military, and remotely-piloted aviation above Mach 5 is discussed with reference to the scramjet. Actively cooled aircraft structures of low weight are described, together with jet nozzle design and combustion parameters. The scramjet is seen as operating alone or in tandem with ramjet propulsion, which would power an aircraft up to scramjet speeds. Attention is given to the specific impulse of the scramjet engine, with hydrogen as the primary fuel. Applications include: advanced reconnaissance and interceptor aircraft, strategic cruise (both aircraft and missiles), highly-maneuverable interceptor missiles, transports, aircraft-type launch vehicles, first stages for Space Shuttle launching craft, and single-stage-to-orbit vehicles. Research has focused on increasing the propulsion power of the scramjet engine, while reducing drag on the accompanying airframe.

Jones, R. A.↗
NASA NTRS1979

Laser rocket system analysis

The laser rocket systems investigated in this study were for orbital transportation using space-based, ground-based and airborne laser transmitters. The propulsion unit of these systems utilizes a continuous wave (CW) laser beam focused into a thrust chamber which initiates a plasma in the hydrogen propellant, thus heating the propellant and providing thrust through a suitably designed nozzle and expansion skirt. The specific impulse is limited only by the ability to adequately cool the thruster and the amount of laser energy entering the engine. The results of the study showed that, with advanced technology, laser rocket systems with either a space- or ground-based laser transmitter could reduce the national budget allocated to space transportation by 10 to 345 billion dollars over a 10-year life cycle when compared to advanced chemical propulsion systems (LO2-LH2) of equal capability. The variation in savings depends upon the projected mission model.

Jones, W. S.↗
NASA NTRS1980

Recent development of a jet-diffuser ejector

The paper considers thrust augmenting ejectors in which the processes of mixing and diffusion are partly carried out downstream of the ejector solid surfaces. A jet sheet surrounding the periphery of a widely diverging diffuser prevents separation and forms a gaseous, curved surface to provide effective diffuser ratio and additional length for mixing of primary and induced flows. Three-dimensional potential flow methods achieved a large reduction in the length of the associated solid surface; primary nozzle design further reduced the volume required by the jet-diffuser ejectors, resulting in thrust augmentation in excess of two, and an overall length of about 2 1/2 times the throat width.

Alperin, M.↗
NASA NTRS1980

Shuttle subscale ablative nozzle tests

Recent subscale nozzle tests have identified new and promising carbon phenolic nozzle ablatives which utilize staple rayon, PAN, and pitch based carbon cloth. A 4-inch throat diameter submerged test nozzle designed for the 48-inch Jet Propulsion Laboratory char motor was used to evaluate five different designs incorporating 20 candidate ablatives. Test results indicate that several pitch and PAN-based carbon phenolic ablatives can provide erosion and char performance equivalent or superior to the present continuous rayon-based SRM ablative.

Powers, L. B.↗
NASA NTRS1983

Sodium Spray Would Speed Silicon Production

Production rate of solar-grade silicon in sodium/silicon tetrafluoride reactor increase by spray feed. Liquid-sodium droplet size is controlled by pressure of argon gas and by nozzle design. Baffle helps to prevent reactor opening from becoming clogged by reaction products.

Sancier, K. M.↗
NASA NTRS1985

Shock associated noise of inverted-profile coannular jets. II - Condition for minimum noise. III - Shock structure and noise characteristic

The generation of noise by the shock-turbulence interaction with shock cells in an inverted-profile coannular jet with nozzle exit velocity aligned with the jet axis is investigated analytically, interpreting the optical measurements of Tanna et al. (1985). The noise-intensity minimum at slightly supersonic primary-flow velocities is related to the weakness of the primary-stream shock-cell structure and the lack of such a pattern in the outer fan stream. The discrepancies between this finding and those of Dosanjh et al. (1977 and 1978) are attributed to nozzle design, the definition of minimum noise, and different interpretative approaches. A first-order shock-cell model is then developed to derive formulas for the peak frequencies and the scaling of noise intensity. The results of computations using these formulas are presented in graphs and found to be in good agreement with the experimental data.

Tam, C. K. W.↗
NASA NTRS1986

Improvements in Ionized Cluster-Beam Deposition

Lower temperatures result in higher purity and fewer equipment problems. In cluster-beam deposition, clusters of atoms formed by adiabatic expansion nozzle and with proper nozzle design, expanding vapor cools sufficiently to become supersaturated and form clusters of material deposited. Clusters are ionized and accelerated in electric field and then impacted on substrate where films form. Improved cluster-beam technique useful for deposition of refractory metals.

Fitzgerald, D. J.↗
NASA NTRS1986

The optimum hypersonic wind tunnel

The capabilities of existing hypersonic wind tunnels in the U.S. are assessed to form a basis for recommendations for a new, costly facility which would provide data for modeling the hypervelocity aerodynamics envisioned for the new generation of aerospace vehicles now undergoing early studies. Attention is given to the regimes, both entry and aerodynamic, which the new vehicles will encounter, and the shortcomings of data generated for the Orbiter before flight are discussed. The features of foreign-gas, impulse, aeroballistic range, arc-heated and combustion-heated facilities are examined, noting that in any hypersonic wind tunnel the flow must be preheated to prevent liquefaction upon expansion in the test channel. The limitations of the existing facilities and the identification of the regimes which must be studied lead to a description of the characteristics of an optimum hypersonic wind tunnel, including the operations and productivity, the instrumentation, the nozzle design and the flow quality. Three different design approaches are described, each costing at least $100 million to achieve workability.

Trimmer, L. L.↗
NASA NTRS1986

Flight effects on noise from coaxial dual flow. II - Heated jets

This paper is a continuation of the study described in Part I and deals with the flight effects on noise from heated jets. The present work shows that coaxial exhaust flows with inverted profiles are much quieter than flows with conventional profiles. Among all possible coaxial configurations with only one of the streams heated conventional profile, inverted profile, and the variable stream control engine (VSCE) cycle - and holding constant mass flow and thrust, a VSCE cycle is the best possible engine cycle as it provides over 18-dB reduction in sound pressure level (as compared to noise from a conventional profile cycle) at all angles, both statically and in flight. The study also indicates that, if both the coaxial streams are heated unequally, a duct-burning profile, combined with the variable stream control engine (DB-VSCE) concept, gives rise to a powerful coaxial device which generates the least noise, both statically and in flight. This concept will be of paramount importance as one of the most variable nozzle designs of the future.

Dash, R.↗
NASA NTRS1986

The preferred spatial mode of instability for a Mach 2 jet

Phase-averaged schlieren video and an array of azimuthally oriented microphones were used in the experiments performed to determine the preferred spatial structure associated with supersonic nozzle design for an exhaust Mach number of 2. The jet flow was unheated, chemically inert, and submerged in a static environment, conditions that are satisfactory for the quasi-linear wave-analytical model of Tam and Morris (1980) and Tam and Burton (1984). For general conditions of undeterminate phase-averaged optical records, a conditional sampling method was devised, based on fundamental multimode components. This method uncovers the preferred spatial structure, and shows that in addition to the dominant jet flapping mode, there is also a significant contribution from the axisymmetric mode. Near-field correlations with a moving microphone indicate that the flapping plane is nearly stationary, and not spinning as in the Westley and Wolley (1975) experiment.

Seiner, J. M.↗
NASA NTRS1987

Computational analysis of hypersonic airbreathing aircraft flow fields

The general problem of calculating the flow fields associated with hypersonic airbreathing aircraft is presented. Unique aspects of hypersonic aircraft aerodynamics are introduced and their demands on computational fluid dynamics are outlined. Example calculations associated with inlet/forebody integration and hypersonic nozzle design are presented to illustrate the nature of the problems considered.

Dwoyer, Douglas L.↗