Search NASA⌕ Search

SEARCH · Search NASA

Results for “ORIENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Tailoring copper current collector roughness and crystallographic orientation to improve lithium plating

Secondary lithium metal batteries are of great interest due to a high theoretical energy density, but rechargeability is limited by the formation of lithium dendrites that lead to internal short circuits and catastrophic cell failure. Mitigating dendrites through uniform current distribution at the current collector is a promising solution to enabling long cycle life of lithium metal electrodes. Here, the impact of copper crystal orientation and roughness on electrochemically deposited lithium morphology is studied. For 50 cycles, the capacity retention from greatest to least followed polycrystalline copper 95 ± 1 % (MC-PC) ≥ 94.55 ± 0.01 % Cu (110) > 93.0 ± 0.4 % Cu(111) > 75.8 ± 0.1 % Cu(100). Cu(100) performed the worst in all cases with shorts occurring frequently before reaching 50 cycles. Cryo-scanning electron microscopy images showed that after 50 cycles, MC-PC Cu had the best lithium morphology, but at early cycles, Cu(111) formed the densest lithium layer. MC-PC Cu had the most uniform lithium nucleation which may have been caused by increased roughness relative to the single crystal samples. When polycrystalline Cu (F-PC) roughness was systematically controlled, the cumulative Coulombic efficiency increased from about 0.3–0.5 with increasing roughness from an Ra of about 10–40 nm. Lastly, plating rates were studied. Slower rates of 0.25 mA/cm 2 exhibited denser lithium morphology in all cases as compared to 0.5 and 1.0 mA/cm 2 , but the relative porosity of Li deposited on the different current collectors depended on the rate applied.

Copper↗
DOE OSTI2021

Control of Surface Morphology during the Growth of (110)-Oriented GaAs by Hydride Vapor Phase Epitaxy

We present a study of the effect of hydride vapor phase epitaxy (HVPE) growth conditions on the morphology of GaAs grown on vicinal and nominally exact (110) GaAs substrates. We evaluate epilayer surfaces using a combination of Nomarski microscopy and atomic force microscopy. The surface morphology strongly depends on the growth conditions employed, as well as the substrate orientation. On substrates offcut 3° toward (111)A, faceting generally develops under conditions in which the growth is Ga-limited, although Ga-limited growth is not the only requirement for faceting. Low growth temperatures lead to a faceted morphology, while higher growth temperatures favor smooth growth and facet-free morphology. We show that the surface morphology is kinetically controlled and that the tendency to facet correlates with the growth rate. 3D growth occurs on nominally exact substrates, resulting in hillock formation, but reduction of the group V precursor partial pressure results in smooth morphology. Overall, our results are consistent with models for step-bunching-induced surface faceting that invoke a negative Ehrlich–Schwoebel step-edge barrier.

(110) oriented GaAs↗
DOE OSTI2024

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data provided valuable insights into another type of non-DLVO interaction, namely the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. In conclusion, our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Synthesis and Self-Assembly of Monodisperse Graphene Nanoribbons: Access to Submicron Architectures with Long-Range Order and Uniform Orientation

Fabricating organic semiconducting materials into large-scale well-organized architectures is critical for building high performance molecular electronics. While graphene nanoribbons (GNRs) hold enormous promise for various device applications, their assembly into a well-structured monolayer or multilayer architecture poses a substantial challenge. Here we report the preparation of length-defined monodisperse GNRs via the integrated iterative binomial synthesis (IIBS) strategy and their self-assembly into submicron-architectures with long-range order, uniform orientation as well as regular layers. Further, the use of short alkyl side chains benefits forming stable multi-layers through interlocking structures. By changing the length and backbone shapes of these monodisperse GNRs, various three-dimensional assemblies including multilayer stripes, monolayer stripes, and nanowires, can be achieved, leading to different photophysical properties and band gaps. The discovery of these intriguing self-assembly behaviors of length-defined GNRs is expected to open the door for various future applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Process‐Oriented Calibration of a Turbulence Scheme in the DOE's Global Storm‐Resolving Model Using Machine Learning

A process‐oriented calibration framework is developed for the Simplified Higher‐Order Closure (SHOC) turbulence scheme in DOE's Simple Cloud Resolving E3SM Atmospheric Model (SCREAM). This framework leverages machine learning surrogates and observational constraints to efficiently calibrate SHOC adjustable parameters across two convective regimes: clear‐sky dry convective boundary layer and fair‐weather shallow cumulus clouds from ARM observations. We use perturbed‐parameter ensembles of a doubly periodic version of SCREAM to train surrogates and apply Markov Chain Monte Carlo sampling guided by cost functions based on benchmarking large‐eddy simulations and observations to identify optimized parameter sets that perform well in both regimes. The calibrated SHOC parameters substantially improve boundary‐layer turbulence and cloud boundaries, and modeled cloud fraction and radiative effects align better with observations than the default. These results demonstrate that combining multiple process‐specific convective regimes with machine‐learning surrogates can reduce parametric uncertainties and yield a model more faithful to cloud–turbulence interactions.

58 GEOSCIENCES↗
DOE OSTI2026

Background-Oriented Schlieren Velocimetry of Helium Coolant Flow in Additively Manufactured Channels

High-pressure helium gas cooling is an attractive solution for thermal management of the fusion blanket first wall, as this coolant is chemically and neutronically inert and separable from hydrogenic species. However, due to the low thermal mass of helium, geometric optimization of these channels is required to provide sufficient cooling at manageable flow rates and pumping burdens. Increasingly, analysis and optimization of these coolant channels rely on computational fluid dynamics (CFD) simulations, and these require relevant experimental data for turbulence model validation. Toward this end, a high-pressure helium gas flow visualization system has been employed to image the flow of helium in flow channels with one-sided heating, mimicking the blanket first wall environment. Flow of helium at 4 MPa pressure and flow rates up to 68 g/s (Reynolds number 57 000) is supplied to rectangular channel test sections, with uniform heating applied to the bottom wall of the channel at heat fluxes varied between roughly 50 and 130 kW/m2. A high-speed camera is used to image index of refraction (IOR) gradients in the fluid via background-oriented schlieren (BOS), and temperature and pressure instrumentation are used to characterize thermal-hydraulic performance of each channel. Cross correlation of time-resolved BOS images is then used to calculate time-averaged 2-D helium velocity fields. Flow in additively manufactured (AM) channels is examined in this manner, including both featureless channels and those containing baffling as a heat transfer enhancement. The flow distribution seen in the featureless case differs significantly from that seen in prior simulations, whereas the flow in the baffled case shows the predicted behavior of flow forced along the heated wall. This augmented flow distribution is seen to increase the heat transfer coefficient in the baffled test section. Here, strategies are discussed for ongoing and future validation of these simulations, with the aim of model deployment for blanket cooling design and optimization.

Additive manufacturing↗
DOE OSTI2024

A high fidelity and user-friendly equation-oriented optimization model for carbon capture using a novel water-lean solvent

Research Triangle Institute (RTI) International and SLB have developed a novel water-lean solvent technology for carbon capture, demonstrating low specific reboiler duty (SRD) values at capture rates exceeding 90%. At the Technology Centre Mongstad (TCM) pilot plant, the technology achieved an SRD of 2.55 GJ/t-CO2 at 95% capture, utilizing an intercooler and a 5°C temperature approach in the lean/rich solvent cross exchanger. To meet varying carbon capture targets for Front End Engineering and Design (FEED) studies and to enable real-time optimization and advanced process control, an efficient optimization model is required. This model needs to minimize energy demand for a given capture rate and determine optimal operating parameters in response to fluctuating flue gas conditions. While an existing Aspen Plus simulation model, developed by RTI and SLB, accurately matches TCM plant data, its sequential modular (SM) strategy is too slow for real-time applications due to recycle streams and tight heat integration inherent in solvent-based carbon capture processes. Although an equation-oriented (EO) modeling strategy is more suitable for optimizing these processes, its adoption has been limited by several factors: feature limitations in Aspen Plus EO mode (e.g., lack of balance block support), a less user-friendly interface for variable identification and loop solving, complex troubleshooting of convergence issues, and the necessity for accurate initial values.

carbon capture↗
DOE OSTI2023

Multimodal Characterization of Crystal Structure and Formation in Rubrene Thin Films Reveals Erasure of Orientational Discontinuities

Abstract Multimodal multiscale characterization provide opportunities to study organic semiconducting thin films with multiple length scales, across multiple platforms, to elucidate crystallization mechanisms of the various microstructures that impact functionality. With polarized scanning transmission X‐ray and 4D‐scanning transmission electron microscopy, hybrid crystalline structures in rubrene thin films in which large crystalline domains surround a common nucleus and transition to a spherulite morphology at larger radii is observed. These high‐resolution techniques reveal how azimuthal orientational discontinuities at smaller radii are erased as spherulite morphology takes hold. In situ crystallization in the films with optical microscopy is also captured, discovering the importance of considering the initial temperature increase of a film during thermal annealing over the crystallization timescale. This kinetic information of the radial crystallization rate and of corresponding film heating kinetics is used to estimate the temperature at which the larger crystalline regions transition into a spherulite. By combining the results obtained from the different characterization modes, it is learned that thermal conditions can sensitively affect the crystallization of rubrene and other organic thin films. The observations suggest opportunities for more complex temperature‐dependent processing to maximize hybrid structures’ functionality in organic thin films and demonstrate that multimodal studies deepen the understanding of structure‐function dynamics.

Tan, Jenna A.↗
DOE OSTI2025

Atomistic Mechanisms of the Crystallographic Orientation‐Dependent Cu 1.8 S Conductive Channel Formation in Cu 2 S‐Based Memristors

Achieving multiple types of resistive switching in a single material with controlled ionic motion is a key challenge in neuromorphic computing, traditionally addressed by combining materials with distinct switching behaviors. Here, Cu 2-x S is identified as a promising candidate to overcome this limitation due to its hierarchical phase transitions. Using in situ biasing experiments, reversible and non-reversible phase transitions (and resistive switching) are demonstrated in γ-Cu 2 S by controlling the compliance current. The formation of parallel high-digenite Cu 1.8 S channels, orientated along the γ-Cu 2 S [201] crystallographic direction, drives the nonvolatile resistive switching. These channels emerge via an intermediate δ-Cu 2 S phase and are stabilized at room temperature by residual strains, alongside β-Cu 2 S phase. In conclusion, the work clarifies the complex, electrically triggered phase transformations in γ-Cu 2 S, and highlights the potential of Cu 2-x S as a versatile material for neuromorphic computing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Scan‐Path‐ and Initial‐State‐Dependent Superdomain Switching in (111)‐Oriented PZT

Polarization switching in ferroelectric materials arises from the collective evolution of complex domain hierarchies, yet deterministic control over these processes remains challenging. Here, we investigate scan-path- and initial-state-dependent switching in epitaxial (111)-oriented PbZr 0.2 Ti 0.8 O 3 thin films using automated AFM-based writing combined with quantitative 3D piezoresponse force microscopy. We show that the scan trajectory acts as an experimentally accessible control parameter for superdomain formation. Box-in-box raster scans reproducibly stabilize ordered stripe superdomains with a reduced subset of symmetry-allowed variants, whereas spiral trajectories generate frustrated mixed-variant states with a broader distribution of final microstructures. Automated pulsing experiments further show that the local superdomain configuration at the nucleation site strongly influences the final written morphology. Phase-field modeling qualitatively reproduces the contrast between representative initial-state geometries and supports the role of compatibility constraints among competing ferroelastic pathways. These findings establish scan-path and initial-state engineering as practical handles to program ferroic order in hierarchical ferroelectric domain structures.

Vasudevan, Rama K. [Oak Ridge National Laboratory ↗
DOE OSTI2022

Application of an equation‐oriented framework to formulate and estimate parameters of chemical looping reaction models

Abstract Accurate, predictive reaction models are critical for the design and optimization of chemical looping combustion (CLC) reactors. The formulation and estimation of kinetic parameters for these reaction models using a first‐principles equation‐oriented (EO) approach is particularly beneficial as large amounts of experimental data spanning process‐relevant conditions can be used to estimate parameters in a computationally tractable way. This work demonstrates the application of a novel EO framework to develop reduction reaction kinetic models of an iron‐based CLC oxygen carrier (OC). An optimization problem is formulated to estimate kinetic parameters that provide the best fit to the experimental data. The model predicts the state of the OC with mean square error values of 2.5%–4.4% across the full range of validation data, including multiple reduction cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A complementarity-based vapor-liquid equilibrium formulation for equation-oriented simulation and optimization

Vapor-Liquid Equilibrium (VLE) is a cornerstone of computer aided process engineering (CAPE). Embedded within process system models, VLE calculations are inherently procedural with non-smooth behavior that frequently require discrete decisions. Traditionally, these features resist the incorporation of VLE within efficient, large-scale equation-oriented (EO) process simulation and optimization strategies. On the other hand, recent reformulation of VLE models through the incorporation of complementarity constraints has broadened its scope to deal seamlessly with phase transitions and even supercritical excursions in process simulation and optimization. In this study, we extend these VLE complementarity models to EO frameworks where procedural thermodynamic property libraries are still required. Here, we develop an efficient, non-intrusive, and intuitive “square-flash” equation system that has been implemented within the IDAES Integrated Platform (IDAES-IP). Further, the effectiveness of this modular approach is demonstrated on case studies for non-ideal flash calculations and distillation optimization with disappearing phases and supercritical transitions.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Coconut oil derived five‐component synthetic oviposition deterrent for oriental fruit fly, Bactrocera dorsalis

Abstract BACKGROUND Bactrocera dorsalis, oriental fruit fly (OFF), is one of the most destructive agricultural pests. Although bait sprays can effectively control OFF,resistance development has been a concern. We evaluated the oviposition deterrent activity of coconut free fatty acids (CFFA), a mixture of eight coconut oil‐derived fatty acids known to repel hematophagous insects and deter their feeding and oviposition, against OFF females. RESULTS In laboratory 72‐h two‐choice assays using guava‐juice infused‐agar as an oviposition substrate, CFFA deterred OFF oviposition in a dose‐dependent manner with the greatest reduction of 87% at 20 mg dose compared to the control. When the eight CFFA components were tested individually, four compounds (caprylic, capric, oleic, and linoleic acids) significantly reduced OFF oviposition (‘negative‐compounds’), two (lauric and myristic acids) had no effect (‘neutral‐compounds’), and two (palmitic and stearic acids) stimulated OFF oviposition (‘positive‐compounds’). In two‐choice tests, the ‘negative‐compounds’ blend failed to elicit the same level of oviposition reduction as CFFA at equivalent concentrations found in CFFA. Adding the two ‘neutral‐compounds’ recovered the oviposition deterrence similar to CFFA. Subsequent subtraction tests showed that four ‘negative‐compounds’ plus lauric acid was as effective as CFFA in reducing OFF oviposition in guava‐juice agar. This five‐component key‐deterrent blend also reduced OFF oviposition by 95 and 72% on papaya and tomato fruit, respectively. CONCLUSION CFFA acts as an oviposition deterrent for OFF. Given that CFFA compounds are generally regarded as safe for humans and the environment, CFFA and its bioactive components have potential use in behavioral control strategies against OFF. © 2023 Society of Chemical Industry. This article has been contributed to by U.S. Government employees and their work is in the public domain in the USA.

Agriculture↗
DOE OSTI2020

Effects of Surface Orientation and Termination Plane on Glass‐to‐Crystal Transformation of Lithium Disilicate by Molecular Dynamics Simulations

Glass‐to‐crystal transformation of lithium disilicate is studied using molecular dynamics simulations using an effective partial charge potential. The structural evolution of the interface between glassy and crystalline lithium disilicate is analyzed to simulate crystallization of glass on pre‐existing crystal seeds. Besides previously used atomic number density, the distribution of Q n species (Si tetrahedra with n bridging oxygen) is shown to be an effective parameter for following this transformation quantitatively. The early stages of crystal growth are significantly affected by the orientation and termination of the surface of adjacent crystal, as indicated by calculated atomic density, partial ordering, atomic segregation, and an increase in Q 3 concentration. In particular, under‐coordinated Si within the outer crystal layer is found to be most effective in transforming the amorphous structure toward crystallinity. The increase in Q 3 in the glass close to interface region most clearly shows the initial stage of lithium disilicate crystal growth.

Sun, Wei↗
DOE OSTI2021

Identifying build orientation of 3D-printed materials using convolutional neural networks

The advent of additive manufacturing (AM) processes brought with it intense research into various materials and manufacturing processes. At the same time, the need for validation of material properties, as well as study and forecasting of aging, has arisen. Modern imaging techniques, like X-ray computed tomography (XCT), are a convenient vehicle for such studies; however, the large datasets they produce require novel analysis techniques to efficiently extract critical information. Here, we present our work on developing a 3D extension of the ResNet architecture to distinguish between two build orientations of tensile bars produced by AM. Using only information from XCT, our method achieves a 99.3% correct classification at a misidentification of 1%.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quantized Grain Boundary States Promote Nanoparticle Alignment During Imperfect Oriented Attachment

Oriented attachment (OA) has become a well-recognized mechanism for the growth of metal, ceramic, and biomineral crystals. While many computational and experimental studies of OA have shown that particles can attach with some misorientation then rotate to remove adjoining grain boundaries, the underlying atomistic pathways for this “Imperfect OA” process remain the subject of debate. In this paper, molecular dynamics and in situ TEM were used to probe the crystallographic evolution of up to 30 gold and copper nanoparticles during aggregation. It was found that Imperfect OA occurs because (1) grain boundaries become quantized when their size is comparable to the separation between constituent dislocations and (2) kinetic barriers associated with the glide of grain boundary dislocations are small. In support of these findings, TEM experiments show the formation of a single crystal aggregate after annealing 9 initially misoriented, agglomerated particles with evidence of dislocation slip and twin formation during particle/grain alignment. These observations motivate future work on assembled nanocrystals with tailored defects and call for a revision of Read-Shockley models for grain boundary energies in nanocrystalline materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Comparison of Solid Electrolyte Interphase Formation and Evolution on Highly Oriented Pyrolytic and Disordered Graphite Negative Electrodes in Lithium–Ion Batteries

The presence and stability of solid electrolyte interphase (SEI) on graphitic electrodes is vital to the performance of lithium-ion batteries (LIBs). However, the formation and evolution of SEI remain the least understood area in LIBs due to its dynamic nature, complexity in chemical composition, heterogeneity in morphology, as well as lack of reliable in situ/operando techniques for accurate characterization. In addition, chemical composition and morphology of SEI are not only affected by the choice of electrolyte, but also by the nature of the electrode surface. While introduction of defects into graphitic electrodes has promoted their electrochemical properties, how such structural defects influence SEI formation and evolution remains an open question. In this work, utilizing nondestructive operando electrochemical atomic force microscopy (EChem-AFM) the dynamic SEI formation and evolution on a pair of representative graphitic materials with and without defects, namely, highly oriented pyrolytic and disordered graphite electrodes, are systematically monitored and compared. Complementary to the characterization of SEI topographical and mechanical changes during electrochemical cycling by EChem-AFM, chemical analysis and theoretical calculations are conducted to provide mechanistic insights underlying SEI formation and evolution. The results provide guidance to engineer functional SEIs through design of carbon materials with defects for LIBs and beyond.

25 ENERGY STORAGE↗
DOE OSTI2024

Automatic Digitization and Orientation of Scanned Mesh Data for Floor Plan and 3D Model Generation

This paper describes a novel approach for generating accurate floor plans and 3D models of building interiors using scanned mesh data. Unlike previous methods, which begin with a high resolution point cloud from a laser range-finder, our approach begins with triangle mesh data, as from a Microsoft HoloLens. It generates two types of floor plans, a “pen-and-ink” style that preserves details and a drafting-style that reduces clutter. It processes the 3D model for use in applications by aligning it with coordinate axes, annotating important objects, dividing it into stories, and removing the ceiling. Its performance is evaluated on commercial and residential buildings, with experiments to assess quality and dimensional accuracy. Our approach demonstrates promising potential for automatic digitization and orientation of scanned mesh data, enabling floor plan and 3D model generation in various applications such as navigation, interior design, furniture placement, facilities management, building construction, and HVAC design.

Sharma, Ritesh↗