Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optimized electrodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Optimization of La 2 NiO 4+δ Electrolysis Cell Oxygen Electrode through Surfactant-Enabled LaCoO 3±δ Nanocatalyst Deposition

Lanthanum nickelate (LNO) has shown promise as a Cr-resistant air electrode material for SOECs but has suboptimal surface oxygen exchange properties. Nanocoating of the LNO surface with lanthanum cobaltite (LCO) was chosen to improve cell performance as a surface oxygen conductor. The work focused on the implementation of a two-step nano-LCO film deposition utilizing catechol molecules in a porous LNO electrode. The subgoals of the work were to maintain nanosized LCO particles/ grains to increase active surface area and to control the regularity/ homogeneity of the coating across the microstructure. To achieve these goals, a novel surfactant-enhanced liquid infiltration method was utilized, where nucleation sites were spread across the electrode structure to control the location and size of LCO particles. Various catechol surfactant compositions were evaluated for their ability to control the kinetics of nanoparticle deposition and the homogeneity of the coating. Chelated LCO was characterized by X-ray diffraction (XRD), which found a substantial improvement in LCO formation with surfactant addition and determined polymerized norepinephrine to be the best-performing surfactant, with 88.4% pure LCO formed at low temperature. X-ray photoelectron spectroscopy (XPS) confirmed LCO nanostructures formed by the two-step infiltration process, showing no impurities and a stable perovskite structure. Deposition kinetics were analyzed using atomic force microscopy (AFM), correlating infiltration times and solution molarity to nanoparticle size and distribution, the results of which were confirmed in symmetrical cell samples by scanning electron microscopy (SEM). Electrochemical impedance spectroscopy (EIS) testing demonstrated substantial improvements in polarization resistance, where the nanocoating reduced the resistance by ∼55% to 0.152 Ω·cm 2 at 700 °C and 0.039 Ω·cm 2 at 800 °C. Electrical conductivity relaxation (ECR) at this temperature confirmed an improved surface oxygen exchange coefficient of the LCO + LNO heterostructure predicted by the Bode data from EIS, alongside a reduction in activation energy by about 30%.

Deposition↗

3D-printed micro ion trap technology for quantum information applications

Trapped-ion applications, such as in quantum information processing1, precision measurements, optical clocks and mass spectrometry, rely on specialized high-performance ion traps. The last three of these applications typically use traditional machining to customize macroscopic 3D Paul traps, whereas quantum information processing experiments usually rely on photolithographic techniques to miniaturize the traps and meet scalability requirements. Using photolithography, however, it is challenging to fabricate the complex 3D electrode structures required for optimal confinement. Here, in this work, we demonstrate a high-resolution 3D printing technology based on two-photon polymerization (2PP) that is capable of fabricating large arrays of high-performance miniaturized 3D traps. We show that 3D-printed ion traps combine the advantages, such as strong radial confinement, of traditionally machined 3D traps with on-chip miniaturization. We trap calcium ions in 3D-printed ion traps with radial trap frequencies ranging from 2 MHz to 24 MHz. The tight confinement eases ion cooling requirements and allows us to implement high-quality Rabi oscillations with Doppler cooling only. Also, we demonstrate a two-qubit gate with a Bell-state fidelity of 0.978 ± 0.012. With 3D printing technology, the design freedom is greatly expanded without sacrificing scalability and precision, so that ion trap geometries can be optimized for higher performance and better functionality.

quantum information↗

Electrophoretic deposition improves catalytic performance of Co 3 O 4 nanoparticles for oxygen reduction/oxygen evolution reactions

The effects of nanoparticle deposition on the catalytic activity of Co 3 O 4 nanoparticles for the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) are evaluated for two deposition methods: dropcasting and electrophoretic deposition (EPD). In this work it is found that the EPD catalyst films demonstrate better catalytic activity per unit mass than do the dropcast films, as defined by diffusion-limited current, by approximately 27% for ORR and 25% for OER. When accounting for different loading levels, the absolute activities of these catalysts are superior to those of other reported Co 3 O 4 colloidal nanoparticulate catalysts without conductive additives, showing that this material has excellent intrinsic activity for future optimization. Inspection of the electrode kinetics shows that EPD catalysts have more favorable characteristics as exhibited by their smaller Tafel slope (96 mV per decade for EPD versus 109 mV per decade for dropcast films). We analyze this enhancement by determining the metal oxide surface area for each catalyst film using a novel sequential metal deposition technique starting with electrodeposition of Ag followed by Pb underpotential deposition (UPD). Through UPD experiments we find, surprisingly, that EPD films have a smaller surface area than the dropcast films. We conclude that EPD films are more active per unit surface area. When accounting for surface area and mass, the EPD catalyst outperforms dropcast by a factor of 2.5 for ORR and 2.6 for OER. We anticipate that morphological differences in the EPD films relative to the dropcast ones, such as particle coverage and electrical conductivity, are responsible for this behavior. Such a result has important implications for future studies on the structure of EPD-manufactured nanoparticulate thin films and on the mechanisms for performance enhancement in such catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enzymatic X-ray absorption spectroelectrochemistry

X-ray absorption spectroelectrochemistry has the potential to provide insight into enzyme mechanisms. However, protein loading on the electrode surface must be optimized and controls in place to differentiate electrochemically driven changes from beam induced damage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Graphene oxide precursor effects on 3D-printed carbon scaffolds

Manganese oxide (MnO 2 ), an earth-abundant material, is a promising component for energy storage devices, with uses in both pseudocapacitors and batteries. However, high MnO 2 loading often leads to reduced performance due to poor ion diffusion. 3D printing, particularly using the direct ink writing (DIW) technique, offers a solution by enabling the fabrication of electrodes with hierarchical porous structures and open channels that enhance mass transport and ion diffusion. Previous work demonstrated that 3D-printed graphene aerogels with MnO 2 coatings exhibited excellent electrochemical performance, even with thick electrodes, due to their optimized structure. Building on this work, the current study investigates the performance differences between aerogels developed using graphene oxide (GO) and reduced graphene oxide (rGO) as carbon precursors. Both materials were incorporated into thixotropic inks, 3D-printed into lattice structures, and carbonized. Despite expected similarities between the final graphene aerogel, rGO-based aerogels exhibited superior areal capacitance, compared to GO-based aerogels. These differences are attributed to the lower oxygen content and defect density of rGO, which influence its interaction with cellulose viscosifiers in the ink formulation. Brunauer–Emmett–Teller (BET) surface area analysis revealed that rGO aerogels exhibit a larger surface area and mesoporous structure, further enhancing their performance. When coated with MnO 2 , rGO-based aerogels maintained their superior capacitive behavior over GO-based aerogels. This study highlights the effect of carbon precursor on the end performance of graphene aerogels.

Materials science↗

Design considerations for gallium arsenide pulse compression photoconductive switch

In this paper, we present the physics and design-space exploration of a novel pulse compression photoconductive switch (PCPS) using semi-insulating gallium arsenide (GaAs) operating in the negative differential mobility (NDM) regime of electron transport. We systematically quantify the relationship between the PCPS performance and various design options, including contact separation, laser energy and placement, and trap dynamics. Specifically, we report the full-width at half-maximum and the peak output current generated by the PCPS as a function of applied electrical and optical bias. We discuss the optimal spacing between the electrodes and the distance of the laser spot to the anode to achieve higher electron confinement and superior radio-frequency (RF) metrics. Reducing the laser energy is important to prevent the appearance of secondary peaks due to diffusive transport, but there exists a trade-off between the bandwidth and the maximum current of the PCPS. We also compare the PCPS response with and without trap dynamics and find that the electrostatic screening from the trap-induced space charge is time-independent when the trapping time constant is set larger than the recombination lifetime. Overall, trap dynamics are detrimental to performance, unless the compensation doping scheme to achieve semi-insulating GaAs is carefully selected. Results presented in this paper can be used by experimentalists to fine-tune the PCPS design parameters to meet the specifications of various RF applications. Moreover, our results will provide a strong theoretical basis to the measurements of PCPS devices using GaAs and other NDM materials under investigation.

42 ENGINEERING↗

Connection between the physicochemical characteristics of amorphous carbon thin films and their electrochemical properties

Connecting a material's surface chemistry with its electrocatalytic performance is one of the major questions in analytical electrochemistry. This is especially important in many sensor applications where analytes from complex media need to be measured. Unfortunately, today this connection is still largely missing except perhaps for the most simple ideal model systems. Here we present an approach that can be used to obtain insights about this missing connection and apply it to the case of carbon nanomaterials. In this paper we show that by combining advanced computational techniques augmented by machine learning methods with x-ray absorption spectroscopy (XAS) and electrochemical measurements, it is possible to obtain a deeper understanding of the correlation between local surface chemistry and electrochemical performance. As a test case we show how by computationally assessing the growth of amorphous carbon (a-C) thin films at the atomic level, we can create computational structural motifs that may in turn be used to deconvolute the XAS data from the real samples resulting in local chemical information. Then, by carrying out electrochemical measurements on the same samples from which x-ray spectra were measured and that were further characterized computationally, it is possible to gain insight into the interplay between the local surface chemistry and electrochemical performance. To demonstrate this methodology, we proceed as follows: after assessing the basic electrochemical properties of a-C films, we investigate the effect of short HNO 3 treatment on the sensitivity of these electrodes towards an inner sphere redox probe dopamine to gain knowledge about the influence of altered surface chemistry to observed electrochemical performance. Overall, these results pave the way towards a more general assessment of electrocatalysis in different systems and provide the first steps towards data driven tailoring of electrode surfaces to gain optimal performance in a given application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cavallo's multiplier for in situ generation of high voltage

Here, a classic electrostatic induction machine, Cavallo's multiplier, is suggested for in situ production of very high voltage in cryogenic environments. The device is suitable for generating a large electrostatic field under conditions of very small load current. Operation of the Cavallo multiplier is analyzed, with quantitative description in terms of mutual capacitances between electrodes in the system. A demonstration apparatus was constructed, and measured voltages are compared to predictions based on measured capacitances in the system. The simplicity of the Cavallo multiplier makes it amenable to electrostatic analysis using finite element software, and electrode shapes can be optimized to take advantage of a high dielectric strength medium such as liquid helium. A design study is presented for a Cavallo multiplier in a large-scale, cryogenic experiment to measure the neutron electric dipole moment.

47 OTHER INSTRUMENTATION↗

Demonstration of Spectral Selectivity of Efficient and Ultrafast GaN/AlGaN-Based Metal–Semiconductor–Metal Ultraviolet Photodiodes

Efficient and ultrafast (aluminum)-gallium-nitride-based metal-semiconductor-metal (Al x )Ga 1–x N ultraviolet photodiodes were implemented to investigate the spectral properties of GaN/AlGaN-based photodetectors. Al composition of the GaN templates were varied from 0-% to 30% to demonstrate the impact of Al mole fraction on the cutoff wavelength of these UV photodiodes. Asymmetric metal contact electrodes were fabricated to optimize the external quantum efficiency without compromising their ultrafast photoresponse. Here, the best performing devices exhibited a peak response of 4 V and an oscilloscope limited temporal pulse width of 61 ps at a 20-V bias with a peak spectral responsivity of 36.5 mA/W at 280 nm.

42 ENGINEERING↗

Strategies for Reducing the PGM Loading in High Power AEMFC Anodes

Anion Exchange Membrane Fuel Cells (AEMFCs) have experienced a significant rise in attention in recent years, largely motivated by the potential to overcome the costs that have plateaued for proton exchange membrane fuel cells. However, despite significant advances in power generation, membrane conductivity, membrane stability, and catalyst activity, the vast majority of high performing AEMFCs are fabricated with a high PGM loading (0.4-0.8 mg cm -2 ). This work demonstrates an electrode fabrication method that reduces the anode catalyst loading by 85 % while still achieving performance ca. 1 W cm -2 - accomplished by designing a multi-layered electrode comprised of an optimized ionomer:carbon:PGM ratio catalyst layer coupled with a hydrophobic microporous layer. If paired with a high-performing PGM-free cathode, this new anode can meet existing DOE PGM loading and performance targets.

30 DIRECT ENERGY CONVERSION↗

Material Design Strategies to Achieve Simultaneous High Power and High Energy Density

ABSTRACT Emerging applications require batteries to have both high energy and high power which are not necessarily compatible. The typical inverse relationship between power and energy in batteries is often due to the slow ion diffusion in electrode materials. While the optimization of current battery technology may be sufficient to fully address this issue, we present here that novel chemistry-focused strategies based on new fundamental understanding of materials may be applied to lead to the development of a new generation of batteries that store energy sufficiently and deliver it rapidly.

energy storage (including batteries and capacitors↗

Stationary Direct Methanol Fuel Cells Using Pure Methanol

This project developed stationary direct methanol fuel cells (DMFCs) using pure methanol as the fuel, integrating complementary institutional expertise on platinum group metals free (PGM-free) cathode catalyst (UB), supported anode catalysts (KSU), electrode fabrication, characterization, and optimization (CMU), and multi-phase mass transfer (KU). The proposed cost-effective prototype will deliver reliable and durable performance using a methanol-tolerant PGM-free cathode and a high-performance anode with low PtRu loading. At the end of the project, the research team is expected to deliver a single cell (50 cm 2 ) with ≤3 mg PGM /cm 2 that achieves 300 mW/cm 2 using pure methanol.

30 DIRECT ENERGY CONVERSION↗

Pulse Electrodeposition for Carbonate-Rich Deposits from Seawater

Seawater electrodeposition is gaining renewed interest in the context of sustainable development, both to build climate-resilient coastal infrastructure and for ocean-based decarbonization applications. Most of the applications benefit from CaCO 3 -rich deposits, but constant-voltage electrodeposition results in a mixture of CaCO 3 and Mg(OH) 2 , especially at higher voltages where precipitation rates are more desirable. The use of pulse voltages can help control interfacial pH that dictates the precipitation reactions. Here, we explore the use of pulse electrodeposition as a function of pulse frequency and duty cycle to control deposit composition. The most CaCO 3 -rich deposits were obtained under 10 Hz frequency and 10% duty cycle conditions for the voltage window investigated (-0.8 V to -1.2 V vs. SCE). While pulsing the voltage increases the amount of CaCO 3 deposited, the energy required per gram of CaCO 3 is significantly higher (14.5×) when compared to the base case of applying a constant voltage of -0.8 V vs. SCE. Further optimization of pulse conditions, electrode materials, and system configuration could lead to finding parameters that result in exclusively carbonate deposits without compromising precipitation rates, which may prove to be more useful for corrosion protection, coastal infrastructure, and other applications in sustainable development.

54 ENVIRONMENTAL SCIENCES↗

USFOE: Extended Summary - Lithium ion batteries and their manufacturing challenges

There is no one lithium ion battery. With the variety of materials and electrochemical couples at our disposal as shown in the previous talks, we have the opportunity to design battery cells specific for their applications. Such applications require optimization of voltage, state of charge utilization, lifetime needs, and safety considerations. Electrochemical couples allow for designing power and energy ratios and available energy for the application. Integration in a large format cell requires optimized roll to roll electrode manufacturing and active material utilization. Electrodes are coated on a current collector in a composite structure comprised of active material, binders, and conductive additives which requires careful control of colloidal chemistry, adhesion, and solidification. These added inactive materials and the cell packaging reduce energy density. Degree of porosity and compaction in the electrode can impede or enhance battery performance. Pathways are explored to bring batteries from currently commercially available 100Wh/kg and 200Wh/L at $500/kWh to 250Wh/kg and 400Wh/L at $125/kWh.

Daniel, Claus↗

X-ray Diffraction Studies of Single-Crystal Materials for Broad Battery Applications

Single-crystal materials have attracted growing interest in battery research due to their well-defined crystallographic orientation, absence of grain boundaries, and enhanced mechanical and electrochemical stability. This Review provides a comprehensive overview of recent advances in the synthesis, structural evolution, and performance optimization of single-crystal electrodes and solid electrolytes. Particular focus is placed on the application of advanced X-ray diffraction (XRD) techniques, including operando synchrotron diffraction, reciprocal space mapping, and Bragg coherent diffraction imaging, which have enabled in-depth investigations of lattice strain, cation disorder, phase transitions, and defect formation. Representative case studies across Ni-rich layered oxides, spinel-type cathodes, and garnet-based electrolytes are examined to highlight the structural features unique to single crystals. Additionally, the synergistic integration of XRD with machine learning, tomography, and spectroscopy is discussed as a powerful direction for real-time analysis and predictive modeling. Furthermore, these insights provide critical guidance for the rational design of high-performance single-crystal materials in lithium, sodium, and solid-state battery systems.

25 ENERGY STORAGE↗

Quarterly Report on Node (FY2018_Q2): Advanced Electrode and Solid Electrolyte Materials for Elevated Temperature Water Electrolysis to Support UTRC HTE Project

The team in Idaho National Laboratory (INL) has made a good progress towards the milestones in this program to support UTRC. This technical report highlights progress by the HydroGEN Super Proton-Conducting High Temperature Electrodes (SPC HTE) Materials Node Capability in the following areas: (1) measurements of conductivities of two BCZY electrolytes; and investigate their stability in moist conditions (50% H 2 O, 200 hours)., (2) development of PBSCF electrode in proton conducting SOEC button-cell device, (3) performance improvement by optimizing micro-structure of steam electrode to achieve the target in milestone, and (4) research plan for the next quarter, to support UTRC HTE project.

08 HYDROGEN↗