Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA FOCUS DEVICES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Laser-heated capillary discharge waveguides as tunable structures for laser-plasma acceleration

Laser-heated capillary discharge waveguides are novel, low plasma density guiding structures able to guide intense laser pulses over many diffraction lengths and have recently enabled the acceleration of electrons to 7.8 GeV by using a laser-plasma accelerator (LPA). These devices represent an improvement over conventional capillary discharge waveguides, as the channel matched spot size and plasma density can be tuned independently of the capillary radius. This has allowed the guiding of petawatt-scale pulses focused to small spot sizes within large diameter capillaries, preventing laser damage of the capillary structure. High performance channel-guided LPAs require control of matched spot size and density, which experiments and simulations reported here show can be tuned over a wide range via initial discharge and laser parameters. In this paper, measurements of the matched spot size and plasma density in laser-heated capillary discharges are presented, which are found to be in excellent agreement with simulations performed using the MHD code MARPLE. Strategies for optimizing accelerator performance are identified based on these results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Role of the magnetic field in electron transportation in a beam-plasma generator

The passage of a concentrated beam through the extraction system of a beam plasma generator is investigated on the basis of analysis of variations in the beam diameter and emittance. Evolution of these parameters is analyzed in the final section of the extraction device, which is characterized by the high density gradient of the supplied gas. Much attention is given to the influence of the magnetic field on the features of electron beam propagation. It is demonstrated that focusing is favorable to decreasing not only the beam transverse size, but also the growth rate of the beam emittance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impurity Powder Injection Experiments in the Large Helical Device

The Impurity Powder Dropper (IPD) is a device capable of injecting controlled amounts of sub-millimetre powder into the plasma under the action of gravity. In 2019 the IPD was first installed on the Large Helical Device (LHD) in Japan, with the aim of improving the plasma performances through real time boronization and assessing the compatibility of this technique with steady state operation. Extensive series of experiments have been performed using the IPD, focused on the improvement of the plasma performance via low-Z powder injection and the understanding of the underlying physical phenomena. In this article, we review the experiments that took place in the period 2019-2024. The main results include the demonstration of the improvement of the wall conditions (reduction of intrinsic impurity content, wall recycling) both on a shot-to-shot basis and in real time. Furthermore, a reduced-turbulence improved confinement regime has been observed coincident with powder injection, resulting in an increase of the plasma temperature of the order of 25%, with enhancements that can reach up to 50% for ion temperature.

Nespoli, F. [Princeton Plasma Physics Laboratory (↗

Measurement of Magnetic Field using Doppler-Free Saturation Spectroscopy (DFSS) in C-2W FRC Plasma

The Cooperative Research and Development Agreement (CRADA) between Oak Ridge National Laboratory (ORNL) and TAE Technologies (TAE) focused on implementing an existing mobile Doppler-free saturation spectroscopy (DFSS) diagnostic to determine the direction of the equilibrium magnetic field within TAE’s C-2W field-reversed configuration (FRC) fusion device. Non-perturbative measurements of magnetic fields in the core of FRCs can provide critical information needed to constrain equilibrium models and for the continued advancement of the fusion research program at TAE. DFSS is a well-established, laser-based absorption spectroscopy technique used to suppress inhomogeneous (Doppler) broadening and reveal the Zeeman fine structure of the target emission lines. The collaboration involved the use of ORNL’s recently constructed mobile DFSS diagnostic. The DFSS diagnostic was shipped and installed on C- 2W in February 2023. TAE’s expertise was used to design and construct the mechanic support structures required to mount the optical hardware on C-2W. Additionally TAE provide critical input to minimize the noise imposed on the DFSS signal by vibrations of the mechanic support structure during operations. DFSS data was obtained for over 500 C-2W shots and will continue until the expiration of this CRADA on September 30 th 2023. Over the course of this work, significant progress was made to maximize the signal to noise (SNR) ratio. Analysis of recently acquired data is on-going, however, initial indications are highly suggestive that a DFSS signal above background has been successfully acquired in C-2W.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Doppler-Free Saturation Spectroscopy (DFSS) for Magnetic and Electric Field Measurements in an FRC plasma

The Cooperative Research and Development Agreement (CRADA) between Oak Ridge National Laboratory (ORNL) and TAE Technologies (TAE) focused on a feasibility study of Doppler-free saturation spectroscopy (DFSS) as a diagnostic strategy to measure the internal magnetic and electric fields of TAE’s C-2W field-reversed configuration (FRC) fusion device. Non-perturbative measurements of magnetic and electric fields in the core of FRCs can provide critical information needed to constrain equilibrium models and for the continued advancement of the fusion research program at TAE. DFSS is a well-established, laser-based absorption spectroscopy technique used to suppress inhomogeneous (Doppler) broadening linewidths and reveal Zeeman/Stark split hyperfine structures of target emission lines. The collaboration involved the use of ORNL’s suite of experimentally validated quantum mechanical modelling codes to simulate theoretical atomic spectra for a variety of machine parameters and laser beam configurations. TAE’s expertise was heavily used to provide measurements/models of the required machine parameters needed as inputs to the simulations. Results of an all-encompassing error analysis demonstrate the favourable capabilities of the diagnostic and provided invaluable insights as to how DFSS can be best used to accurately measure internal B/E-fields in C-2W.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quantify Plasma Response to Non-Axisymmetric (3D) Magnetic Fields in Tokamaks, Final Report for FES (Fusion Energy Sciences) FY2014 Joint Research Target

The goal of the 2014 Joint Research Target (JRT) has been to conduct experiments and analysis to investigate and quantify the response of tokamak plasmas to non-axisymmetric (3D) magnetic fields. Although tokamaks are conceptually axisymmetric devices, small asymmetries often result from inaccuracies in the manufacture and assembly of the magnet coils, or from nearby magnetized objects. In addition, non-axisymmetric fields may be deliberately applied for various purposes. Even at small amplitudes of order 10 -4 of the main axisymmetric field, such “3D” fields can have profound impacts on the plasma performance. The effects are often detrimental (reduction of stabilizing plasma rotation, degradation of energy confinement, localized heat flux to the divertor, or excitation of instabilities) but may in some case be beneficial (maintenance of rotation, or suppression of instabilities). In general, the magnetic response of the plasma alters the 3D field, so that the magnetic field configuration within the plasma is not simply the sum of the external 3D field and the original axisymmetric field. Typically the plasma response consists of a mixture of local screening of the external field by currents induced at resonant surfaces in the plasma, and amplification of the external field by stable kink modes. Thus, validated magnetohydrodynamic (MHD) models of the plasma response to 3D fields are crucial to the interpretation of existing experiments and the prediction of plasma performance in future devices. The non-axisymmetric coil sets available at each facility allow well-controlled studies of the response to external 3D fields. The work performed in support of the 2014 Joint Research Target has included joint modeling and analysis of existing experimental data, and collaboration on new experiments designed to address the goals of the JRT. A major focus of the work was validation of numerical models through quantitative comparison to experimental data, in order to gain confidence in their ability to predict the performance of ITER and other burning plasmas. An important element of this effort was also to verify experimentally the limits of validity of the models. The rest of this overview will summarize the key results of the work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Statistical analysis and modeling of intermittent transport events in the tokamak scrape-off layer

The turbulence observed in the scrape-off-layer of a tokamak is often characterized by intermittent events of bursty nature, a feature which raises concerns about the prediction of heat loads on the physical boundaries of the device. It appears thus necessary to delve into the statistical properties of turbulent physical fields such as density, electrostatic potential, and temperature, focusing on the mathematical expression of tails of the probability distribution functions. The method followed here is to generate statistical information from time-traces of the plasma density stemming from Braginskii-type fluid simulations and check this against a first-principles theoretical model. The analysis of the numerical simulations indicates that the probability distribution function of the intermittent process contains strong exponential tails, as predicted by the analytical theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

RF heating systems evolution for the WEST project

Tore Supra is dedicated to long pulse operation at high power, with a record in injected energy of 1 GJ (2.8 MW × 380 s) and an achieved capability of 12 MW injected power delivered by 3 RF systems: Lower Hybrid Current Drive (LHCD), Ion Cyclotron Resonance Heating (ICRH) and Electron Cyclotron Resonance Heating (ECRH). The new WEST project (W [tungsten] Environment in Steady-state Tokamak) aims at fitting Tore Supra with an actively cooled tungsten coated wall and a bulk tungsten divertor. This new device will offer to ITER a test bed for validating the relevant technologies for actively cooled metallic components, with D-shaped H-mode plasmas. For WEST operation, different scenarii able to reproduce ITER relevant conditions in terms of steady state heat loads have been identified, ranging from a high RF power scenario (15 MW, 30 s) to a high fluence scenario (10 MW, 1000 s). This paper will focus on the evolution of the RF systems required for WEST. For the ICRH system, the main issues are its ELM resilience and its CW compatibility, three new actively cooled antennas are being designed, with the aim of reducing their sensitivity to the load variations induced by ELMs. The LH system has been recently upgraded with new klystrons and the PAM antenna, the possible reshaping of the antenna mouths is presently studied for matching with the magnetic field line in the WEST configuration. For the ECRH system, the device for the poloidal movement of the mirrors of the antenna is being changed for higher accuracy and speed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measuring characteristic differences between high- and low-performing discharges on the MegaJOuLe Neutron Imaging Radiography (MJOLNIR) DPF

A dense plasma focus (DPF) is a compact coaxial plasma gun, which completes its discharge as a Z-pinch, producing short (<100 ns) pulses of ions, x rays, and/or neutrons. Lawrence Livermore National Laboratory recently constructed and began operating a new device, the MJOLNIR (MegaJOuLe Neutron Imaging Radiography) DPF, which is designed for single-pulse flash neutron radiography. This device has achieved neutron yields of up to 4.1×10 11 neutrons/pulse at 3.3 MA peak current, and higher-current commissioning is under way. Like most DPFs, MJOLNIR exhibits variable yields in some configurations. Here, we present evidence of the role of parasitic current paths within the gun in stochastically influencing the yield. First through “conditioning shots,” where new hardware has been introduced, we show that increased run-down and run-in speeds correlate with higher yields. These observations are consistent with current being delivered to the electrodes but not to the main plasma sheath, degrading the implosion-driving force. Once nominal conditions are established, we correlate low-performing discharges with smaller current dip and associated voltage spike for a fixed machine configuration. A snow-plow model is able to recreate small-magnitude current dips through the introduction of a parasitic current path, and particle-in-cell simulations establish how parasitic current paths lower the ion beam energy available to produce neutrons. Finally, we observe an increased likelihood of shots with low yield and smaller current dip with increasing fill pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Probing the plasma near high power wave launchers in fusion devices for static and dynamic electric fields (invited)

An exploratory study was carried out in the long-pulse tokamak Tore Supra, to determine if electric fields in the plasma around high-power, RF wave launchers could be measured with non-intrusive, passive, optical emission spectroscopy. The focus was in particular on the use of the external electric field Stark effect. The feasibility was found to be strongly dependent on the spatial extent of the electric fields and overlap between regions of strong (>∼1 kV/cm) electric fields and regions of plasma particle recycling and plasma-induced, spectral line emission. Most amenable to the measurement was the RF electric field in edge plasma, in front of a lower hybrid heating and current drive launcher. Electric field strengths and direction, derived from fitting the acquired spectra to a model including time-dependent Stark effect and the tokamak-range magnetic field Zeeman-effect, were found to be in good agreement with full-wave modeling of the observed launcher.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Integrated modeling of RF-induced tungsten erosion at ICRH antenna structures in the WEST tokamak *

This paper introduces STRIPE (Simulated Transport of RF Impurity Production and Emission), an advanced modeling framework developed to analyze material erosion and the global transport of eroded impurities originating from radio-frequency (RF) antenna structures in magnetic confinement fusion devices. STRIPE integrates multiple physics modules: SolEdge3x for scrape-off-layer plasma profiles, COMSOL for 3D RF rectified sheath potentials, RustBCA for erosion yields and surface interactions, and global impurity transport for 3D ion energy-angle distributions and impurity transport. The framework is applied to an ion cyclotron RF-heated L-mode discharge (#57877) in the WEST tokamak, where it predicts a thirty-fold increase in gross tungsten erosion at antenna limiters during the transition from ohmic to ICRH operation. Additionally, under ICRH conditions, a tenfold enhancement in erosion is observed when comparing RF sheath effects to purely thermal sheath conditions. High-charge-state oxygen ions ($\mathrm{O}$ 6+ and above) are identified as the dominant contributors to tungsten sputtering. To validate the model, a synthetic diagnostic tool based on inverse photon efficiency (S/XB coefficients) from the ColRadPy collisional-radiative model enables direct comparison with spectroscopic measurements. Model predictions using a plasma composition of 1% oxygen and 99% deuterium show good agreement with observed W − I (400.9 nm) emission for discharge #57877, supporting the accuracy of the STRIPE framework. This study focuses specifically on gross erosion calculations to demonstrate STRIPE’s capabilities. Future extensions of this work will incorporate net erosion, re-deposition, self-sputtering effects, and whole-device modeling of sputtered tungsten impurity transport. STRIPE is also being applied to other RF-heated linear and toroidal devices, offering valuable insights for antenna design, impurity control, and performance optimization in next-generation fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Relativistic Laser-Plasma Interactions

Ever since the much acclaimed paper of Akhiezer and Polovin plasma theorists have been attempting to comprehend complex dynamics related to the propagation of high and ultra-high intensity electromagnetic (EM) radiation through a plasma. This topic was successfully revisited a number of years later by Kaw and Dawson whose analysis threw more light on the propagation of coupled longitudinal-transverse waves of arbitrary intensity. The high phase velocity case was soon solved exactly by Max and Perkins, (early review). The problem of relativistic laser-plasma interactions is of particular interest concerning the fast ignition concept, relevant to contemporary laser inertial confinement fusion research. Moreover, the understanding of relativistic laser pulse evolution in a plasma is basic to many new applications, including optical-field-ionized x-ray lasers, plasma-based electron accelerator schemes, as well as, interpretation of some astrophysical phenomena, and references, therein). From a text given in two tutorial lectures, in a limited space, we mainly focus on an important paradigm of stimulated Raman scattering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental, numerical and analytical evaluation of j × B -thrust for fast-liquid-metal-flow divertor systems of nuclear fusion devices

Abstract Divertor systems of fusion devices are exposed to intense heat loads from plasmas, which degrade solid plasma-facing components. Fast liquid metal (LM) flow divertors may be more advantageous for this purpose but have risk of piling due to intense magnetohydrodynamic (MHD) drag. However, severe deceleration of the flow could be countered with the injection of currents that are transverse to external magnetic fields, allowing to thrust the flow with j × B (Lorentz) forces. Given that the injection of currents as an approach to propel LM-divertor flows has remained experimentally understudied, this article focuses on the evaluation of j × B -thrust and finding its drawbacks. j × B -thrust was experimentally tested with free-surface-LM flows, a vertical magnetic field and an externally applied current. Experiments were reviewed with a theoretical model, showing agreement in the trends of theory and experiments. Full 3D-MHD-free-surface-flow simulations were also performed with FreeMHD and confirmed the sensitivity to unstable flow behavior in LM systems when applying external currents. Furthermore, excessive power requirements are expected for the implementation of j × B -thrust at the reactor scale, making these systems inefficient for commercial devices. This paper evidences that the simple operation of a LM-flow divertor with j × B -thrust, without any of the instabilities caused from reactor plasmas or parasitic currents, already presents intrinsic challenges.

Magnetohydrodynamics↗

Growth of emittance in laser-plasma electron acceleration in guiding structures

We study angular characteristics, such as emittance and fraction of electrons emitted into a prescribed solid angle, for electron bunches that are accelerated in wake fields generated in various guiding structures – capillary waveguides and plasma channels, in which intense laser pulses propagate. The investigation is performed at various injection energies, which simulate input conditions to different cascades of a multistage electron accelerator. It is shown that, in contrast to the limitations issuing from the requirement of trapping and accelerating a substantial part of bunch electrons, the condition of maintaining the low emittance of the bunch, needed for successful transfer of the accelerated bunch to the entry of the next acceleration cascade or other device, imposes much more strict limitations on the accuracy of focusing of laser radiation to the guiding structure. (paper)

43 PARTICLE ACCELERATORS↗

Gas Puff Imaging Diagnostics of Edge Plasma Turbulence in Magnetic Fusion Devices

Gas puff imaging (GPI) is a diagnostic of plasma turbulence which usesa puff of neutral gas at the plasma edge to increase the local visiblelight emission for improved space-time resolution of plasmafluctuations. This paper reviews gas puff imaging diagnostics of edgeplasma turbulence in magnetic fusion research, with a focus on theinstrumentation, diagnostic cross-checks, and interpretationissues. The gas puff imaging hardware, optics, and detectors aredescribed for about 10 GPI systems implemented over the past ~15years. Comparison of GPI results with other edge turbulence diagnosticresults are described and many common features are observed. Severalissues in the interpretation of GPI measurements are discussed, andpotential improvements in hardware and modeling are suggested.

Gas puff imaging↗

Three Confinement Systems—Spherical Tokamak, Standard Tokamak, and Stellarator: A Comparison of Key Component Cost Elements

Since the 1950s “next-step” fusion devices and power plant studies have been developed for a number of magnetic confinement systems but an open question remains: can a magnetic fusion device be simplified to the point where it will be cost competitive and operate with high availability? Concept designs based on the ARIES advanced tokamak, spherical tokamak (ST), and the quasi-axisymmetric (QAS) stellarator option have progressed in recent years through a series of Princeton Plasma Physics Laboratory (PPPL) studies with an underlying intent to improve the engineering feasibility of each, giving special attention to concepts that simplify the device configuration and improve maintenance features. For the ST option, design details centered on a 3-m Fusion Nuclear Science Facility that evolved to incorporate vertical maintenance, high temperature superconductor magnets, a small inboard duel coolant lead lithium blanket, and a liquid metal divertor. In collaboration with the Korean fusion demonstration reactor (K-DEMO) and CFETR concept study teams the tokamak design has evolved to increase plasma component access within a vertical maintenance approach using enlarged toroidal field coils incorporating a low- and high-field Nb 3 Sn winding pack that provide a peak field of 16 T. A recent PPPL stellarator study focused on simplifying the stellarator winding topology to improve access to in-vessel components; combining coil optimization with winding surfaces that incorporated geometry constraints specified by engineering. This paper centered on a 1000-MW power plant design with a tokamak like vertical maintenance scheme that allows access to remove large internal blanket sectors. Results of three confinement studies (PPPL developed ST, K-DEMO, and QAS stellarator) will be presented to highlight concepts that simplify each device configuration and improved their maintenance features. Furthermore, scaling each option to a common 1000-MW net electric power plant mission allows comparisons to be made of key cost elements such as the size of major core components, sizing of the reactor hall, or external facilities needed to handle and store activated in-vessel components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

FOCUS: A full-orbit CUDA solver for particle simulations in magnetized plasmas

A Full-Orbit CUDA Solver for particle simulations in plasmas, FOCUS, has been developed. The code follows exact particle trajectories by solving Newton’s equations with the Lorentz force. The code can use fields calculated analytically or numerically and it is also possible to use the information provided by equilibrium reconstruction and transport codes. FOCUS has an elastic collisions module which covers the whole particle energy range in magnetic fusion devices. Moreover, an atomic collision module was also included to simulate the interaction of the test particles with neutral or partially ionized species. Regarding performance, the main feature is that the code runs on GPUs, allowing the simulation of a large number of particles using moderate computational resources. Different versions of the code have been used in several papers. Here we present a complete description of its capabilities, the basis physics included and detailed information about the numerical algorithms employed. Finally, some examples are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Conductive Channel for Energy Transmission

For many years the attempts to create conductive channels of big length were taken in order to study the upper atmosphere and to settle special tasks, related to energy transmission. There upon the program of creation of 'Impulsar' represents a great interest, as this program in a combination with high-voltage high repetition rate electrical source can be useful to solve the above mentioned problems (N. Tesla ideas for the days of high power lasers). The principle of conductive channel production can be shortly described as follows. The 'Impulsar' - laser jet engine vehicle - propulsion take place under the influence of powerful high repetition rate pulse-periodic laser radiation. In the experiments the CO{sub 2}-laser and solid state Nd:YAG laser systems had been used. Active impulse appears thanks to air breakdown (<30 km) or to the breakdown of ablated material on the board (>30 km), placed in the vicinity of the focusing mirror-acceptor of the breakdown waves. With each pulse of powerful laser the device rises up, leaving a bright and dense trace of products with high degree of ionization and metallization by conductive nano-particles due to ablation. Conductive dust plasma properties investigation in our experiments was produced by two very effective approaches: high power laser controlled ablation and by explosion of wire. Experimental and theoretical results of conductive canal modeling will be presented. The estimations show that with already experimentally demonstrated figures of specific thrust impulse the lower layers of the Ionosphere can be reached in several ten seconds that is enough to keep the high level of channel conductivity and stability with the help of high repetition rate high voltage generator. Some possible applications for new technology are highlighted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗