Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPELLANT TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1938

Tests of Five Full-Scale Propellers in the Presence of a Radial and a Liquid-Cooled Engine Nacelle, Including Tests of Two Spinners

Wind-tunnel tests are reported of five 3-blade 10-foot propellers operating in front of a radial and a liquid-cooled engine nacelle. The range of blade angles investigated extended from 15 degrees to 45 degrees. Two spinners were tested in conjunction with the liquid-cooled engine nacelle. Comparisons are made between propellers having different blade-shank shapes, blades of different thickness, and different airfoil sections. The results show that propellers operating in front of the liquid-cooled engine nacelle had higher take-off efficiencies than when operating in front of the radial engine nacelle; the peak efficiency was higher only when spinners were employed. One spinner increased the propulsive efficiency of the liquid-cooled unit 6 percent for the highest blade-angle setting investigated and less for lower blade angles. The propeller having airfoil sections extending into the hub was superior to one having round blade shanks. The thick propeller having a Clark y section had a higher take-off efficiency than the thinner one, but its maximum efficiency was possibly lower. Of the three blade sections tested, Clark y, R.A.F. 6, and NACA 2400-34, the Clark y was superior for the high-speed condition, but the R.A.F. 6 excelled for the take-off condition.

Biermann, David↗
NASA NTRS1982

A preliminary comparison between the SR-3 propeller noise in flight and in a wind tunnel

The noise generated by supersonic-tip-speed propellers is addressed. Models of such propellers were tested for acoustics in the Lewis 8-by-6-foot wind tunnel. One of these propeller models, SR-3, was tested in flight on the Jetstar airplane and noise data were obtained. Preliminary comparisons of the maximum blade passing tone variation with helical tip Mach number taken in flight with those taken in the tunnel showed good agreement when corrected to the same test conditions. This indicated that the wind tunnel is a viable location for measuring the noise of these propeller models. Comparisons of the directivities at 0.6 and 0.7 axial Mach number showed reasonable agreement. At 0.75 and 0.8 axial Mach number the tunnel directivity data fell off more towards the front than did the airplane data. A possible explanation for this is boundary layer refraction which could be different in the wind tunnel from that in flight. This may imply that some corrections should be applied to both the airplane and wind tunnel data at the forward angles. At and aft of the peak noise angle the boundary layer refraction does not appear to be significant and no correction appears necessary.

Dittmar, J. H.↗
NASA NTRS1976

Surface tension propellant control for Viking 75 Orbiter

The paper describes the selection, development and qualification of the surface tension system and includes results of low-g drop tower tests of scale models, 1-g simulation tests of low-g large ullage settling and liquid withdrawal, structural qualification tests, and propellant surface tension/contact angle studies. Subscale testing and analyses were used to evaluate the ability of the system to maintain or recover the desired propellant orientation following possible disturbances during the Viking mission. This effort included drop tower tests to demonstrate that valid wick paths exist for moving any displaced propellant back over the tank outlet. Variations in surface tension resulting from aging, temperature, and lubricant contamination were studied and the effects of surface finish, referee fluid exposure, aging, and lubricant contamination on contact angle were assessed. Results of movies of typical subscale drop tower tests and full scale slosh tests are discussed.

Dowdy, M. W.↗
NASA NTRS1930

Tests of Five Metal Model Propellers with Various Pitch Distributions in a Free Wind Stream and in Combination with Model VE-7 Fuselage

This report describes the tests of five adjustable blade metal model propellers both in a free wind stream and in combination with a model fuselage with stub wings. The propellers are of the same form and cross section but have variations in radial distributions of pitch. By making a survey of the radial distribution of air velocity through the propeller plane of the model fuselage it was found that this velocity varies from zero at the hub center to approximately free stream velocity at the blade tip. The tests show that the efficiency of a propeller when operating in the presence of the airplane is, over the working range, generally less than when operating in a free wind stream, but that a propeller with a radial distribution of pitch of the same nature as the radial distribution of air velocity through the propeller plane suffers the smallest loss in efficiency.

Lesley, E P↗
NASA NTRS1972

Liquid propellant thermal conditioning system test program

Results are presented from more than 1500 hours of testing on a liquid hydrogen thermal conditioning unit. Test parameters included: mixer and vent flow rates; tank size; ullage volume; pressurant gas; pressurant temperature; pressure level; and heat rate. Gaseous hydrogen and helium were used as pressurants. Analytical models were developed to correlate the test data and relate the performance to that anticipated in zero gravity. Experimental and theoretical results are presented which relate the variables controlling vapor condensation at a moving interface.

Bullard, B. R.↗
NASA NTRS1989

Liquid Rocket Booster (LRB) for the Space Transportation System (STS) systems study. Appendix A: Stress analysis report for the pump-fed and pressure-fed liquid rocket booster

Pressure effects on the pump-fed Liquid Rocket Booster (LRB) of the Space Transportation System are examined. Results from the buckling tests; bending moments tests; barrel, propellant tanks, frame XB1513, nose cone, and intertank tests; and finite element examination of forward and aft skirts are presented.

Source record↗
NASA NTRS1990

Noise of a simulated installed model counterrotation propeller at angle-of-attack and takeoff/approach conditions

Acoustic results for two model counterrotation propellers are presented. The propellers were tested over a range of rotational speeds and propeller axis angles of attack in both the baseline configuration and the installed configuration consisting of a simulated upstream nacelle support pylon and fuselage section. Acoustic data were taken with a polar microphone probe attached to the downstream propeller housing, capable of surveying directivities at several azimuthal locations. The forward and aft rotor power coefficients and fundamental rotor-alone tone levels are found to be directly controlled by propeller axis angle of attack. The second-order rotor-alone tones are strongly influenced by the upstream pylon wake at 80 percent speed; however, rotor-alone mechanisms control the tone level at 90 percent speed, while rotor-rotor interaction tones are essentially unaffected by the presence of the simulated installation.

Woodward, Richard P.↗
NASA NTRS1933

Tests of Nacelle-propeller Combinations in Various Positions with Reference to Wings. Part I : Thick Wing-N.A.C.A. Cowled Nacelle-Tractor Propeller

This report gives the results in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics on the interference drag and propulsive efficiency of a nacelle-propeller combination located in 21 positions with reference to a thick wing. The lift, drag, and propulsive efficiency were obtained at several angles of attack for each of the 21 locations. A net efficiency was derived for determining the over-all effectiveness of each nacelle location. Best results were obtained with the propeller about 25 per cent of the chord directly ahead of the leading edge. A location immediately above or below the wing near the leading edge was very poor.

Wood, Donald H↗
NASA NTRS1934

Negative Thrust and Torque Characteristics of an Adjustable-Pitch Metal Propeller

This report presents the results of a series of negative thrust and torque measurements made with a 4 foot diameter model of a conventional aluminum-alloy propeller. The tests were made in the 20-foot propeller-research tunnel of the National Advisory Committee for Aeronautics. The results show that the negative thrust is considerably affected by the shape and size of the body behind the propeller, that the maximum negative thrust increases with decrease in blade-angle setting, and that the drag of a locked propeller may be greatly reduced by feathering it into the wind. Several examples of possible applications of the data are given.

Hartman, Edwin P↗
NASA NTRS1999

Strutjet RBCC Engine Performance

In the past two years Strutjet Rocket Based Combined Cycle (RBCC) engine has been tested extensively under the Advanced Reusable Technology (ART) contract from NASA MSFC. RBCC Engines combine the high thrust to weight of the rocket with the high efficiency of the ramjet engine. This propulsion system has the potential to reduce the cost of launching payloads to orbit by up to a factor of 100. In the ART program we have conducted over 100 hot fire tests. The propellants have been hydrogen and oxygen. The Modes tested have included the Air Augmented Rocket (AAR) from M = 0 to 2.4, the Ramjet at M = 2.4 & 6, Scramjet at M = 6 & 8, Scram/Rocket at Mach 8 and Ascent Rocket in Vacuum. This invited paper will present an overview of these test results and plans for future development of this propulsion cycle.

Bulman, Mel↗
NASA NTRS1999

Results of a First Generation Propellant Energy Source Module Testing: Non-Nuclear Testing of Fission System

The use of resistance heaters to simulate heat from fission allows extensive development of fission systems to be performed in non-nuclear test facilities, saving time and money. Resistance heated tests on the Module Unfueled Thermal- hydraulic Test (MUTT) article has been performed at the Marshall Space Flight Center. This paper discusses the results of these experiments to date, and describes the additional testing that will be performed. Recommendations related to the design of testable space fission power and propulsion systems are made.

VanDyke, Melissa↗
NASA NTRS1953

Flight Test Results of Rocket-Propelled Buffet-Research Models Having 45 Degree Sweptback Wings and 45 Degree Sweptback Tails Located in the Wing Chord Plane

Three rocket-propelled buffet-research models have been flight tested to determine the buffeting characteristics of a swept-wing- airplane configuration with the horizontal tail operating near the wing wake. The models consisted of parabolic bodies having 45deg sweptback wings of aspect ratio 3.56, at aspect ratio of 0.3, NACA 64A007 airfoil sections, and tail surfaces of geometry and section identical to the wings. Two tests were conducted with the horizontal tail located in the wing chord plane with fixed incidence angles of -1.5deg on one model and 0deg on the other model. The third test was conducted with no horizontal tail. Results of these tests are presented as incremental accelerations in the body due to buffeting, trim angles of attack, trim normal- and side-force coefficients, wing-tip helix angles, static-directional-stability derivatives , and drag coefficients plotted against Mach number. These data indicate that mild low-lift buffeting was experienced by all models over a range of Mach number from approximately 0.7 to 1.4. It is further indicated that this buffeting was probably induced by wing-body interference and was amplified at transonic speeds by the horizontal tail operating in the wing wake. A longitudinal trim change was encountered by the tail-on models at transonic speeds, but no large changes in side force and no wing dropping were indicated.

Mason, Homer P.↗
NASA NTRS1999

Predicting Slag Generation in Sub-Scale Test Motors Using a Neural Network

Generation of slag (aluminum oxide) is an important issue for the Reusable Solid Rocket Motor (RSRM). Thiokol performed testing to quantify the relationship between raw material variations and slag generation in solid propellants by testing sub-scale motors cast with propellant containing various combinations of aluminum fuel and ammonium perchlorate (AP) oxidizer particle sizes. The test data were analyzed using statistical methods and an artificial neural network. This paper primarily addresses the neural network results with some comparisons to the statistical results. The neural network showed that the particle sizes of both the aluminum and unground AP have a measurable effect on slag generation. The neural network analysis showed that aluminum particle size is the dominant driver in slag generation, about 40% more influential than AP. The network predictions of the amount of slag produced during firing of sub-scale motors were 16% better than the predictions of a statistically derived empirical equation. Another neural network successfully characterized the slag generated during full-scale motor tests. The success is attributable to the ability of neural networks to characterize multiple complex factors including interactions that affect slag generation.

Wiesenberg, Brent↗