SEARCH · Search NASA

Results for “PULSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Generating Submillimeter-Wave Frequencies From Laser Pulses

Semiconductor photoconductive switches generate electrical pulses containing submillimeter-wavelength carrier signals (frequency between 300 and 3,000 GHz) and harmonics thereof when illuminated with short-rise-time pulses from lasers. Device of this type used as local oscilator in heterodyne submillimeter-wave receiver. Electrical output of device coupled via transmission line, waveguide, or antenna to mixer circuitry of receiver. Phase delays between optically activated semiconductor switches determine output carrier frequencies. N electrical pulses generated by each laser pulse. Thus, fundamental output frequency is N times laser-pulse-repetition rate.

Spencer, Michael G.↗

NASA NTRS1993

The efficiency of photovoltaic cells exposed to pulsed laser light

Future space missions may use laser power beaming systems with a free electron laser (FEL) to transmit light to a photovoltaic array receiver. To investigate the efficiency of solar cells with pulsed laser light, several types of GaAs, Si, CuInSe2, and GaSb cells were tested with the simulated pulse format of the induction and radio frequency (RF) FEL. The induction pulse format was simulated with an 800-watt average power copper vapor laser and the RF format with a frequency-doubled mode-locked Nd:YAG laser. Averaged current vs bias voltage measurements for each cell were taken at various optical power levels and the efficiency measured at the maximum power point. Experimental results show that the conversion efficiency for the cells tested is highly dependent on cell minority carrier lifetime, the width and frequency of the pulses, load impedance, and the average incident power. Three main effects were found to decrease the efficiency of solar cells exposed to simulated FEL illumination: cell series resistance, LC 'ringing', and output inductance. Improvements in efficiency were achieved by modifying the frequency response of the cell to match the spectral energy content of the laser pulse with external passive components.

Lowe, R. A.↗

NASA NTRS1993

Response of silicon solar cell to pulsed laser illumination

The response of silicon solar cell(s) to pulsed laser illumination is discussed. The motivation was due to the interest of Earth to space/Moon power beaming applications. When this work began, it was not known if solar cells would respond to laser light with pulse lengths in the nanosecond range and a repetition frequency in the kHz range. This is because the laser pulse would be shorter than the minority carrier lifetime of silicon. A 20-nanosecond (ns) full width half max (FWHM) pulse from an aluminum-gallium/arsenide (Al-Ga-As) diode laser was used to illuminate silicon solar cells at a wavelength of 885 nanometers (nm). Using a high-speed digital oscilloscope, the response of the solar cells to individual pulses across various resistive loads was observed and recorded.

Willowby, D.↗

NASA NTRS1994

Modeling of high efficiency solar cells under laser pulse for power beaming applications

Solar cells have been used to convert sunlight to electrical energy for many years and also offer great potential for non-solar energy conversion applications. Their greatly improved performance under monochromatic light compared to sunlight, makes them suitable as photovoltaic (PV) receivers in laser power beaming applications. Laser beamed power to a PV array receiver could provide power to satellites, an orbital transfer vehicle, or a lunar base. Gallium arsenide (GaAs) and indium phosphide (InP) solar cells have calculated efficiencies of more than 50 percent under continuous illumination at the optimum wavelength. Currently high power free-electron lasers are being developed which operate in pulsed conditions. Understanding cell behavior under a laser pulse is important in the selection of the solar cell material and the laser. An experiment by NAsA lewis and JPL at the AVLIS laser facility in Livermore, CA presented experimental data on cell performance under pulsed laser illumination. Reference 5 contains an overview of technical issues concerning the use of solar cells for laser power conversion, written before the experiments were performed. As the experimental results showed, the actual effects of pulsed operation are more complicated. Reference 6 discusses simulations of the output of GaAs concentrator solar cells under pulsed laser illumination. The present paper continues this work, and compares the output of Si and GaAs solar cells.

Jain, Raj K.↗

NASA NTRS1994

Pulsed laser illumination of photovoltaic cells

In future space missions, free electron lasers (FEL) may be used to illuminate photovoltaic array receivers to provide remote power. Both the radio-frequency (RF) and induction FEL provide FEL produce pulsed rather than continuous output. In this work we investigate cell response to pulsed laser light which simulates the RF FEL format. The results indicate that if the pulse repetition is high, cell efficiencies are only slightly reduced compared to constant illumination at the same wavelength. The frequency response of the cells is weak, with both voltage and current outputs essentially dc in nature. Comparison with previous experiments indicates that the RF FEL pulse format yields more efficient photovoltaic conversion than does an induction FEL pulse format.

Yater, Jane A.↗

NASA NTRS1978

Synchronized flash photolysis and pulse deposition in matrix isolation experiments

An apparatus is described which permits flash photolysis of a pulse-deposited gas mixture in a matrix isolation experiment. This technique obviates the limitations of in situ photolysis imposed by the cage effect and by secondary photolysis. The matrix is deposited in pulses at 30-s intervals and photolyzed sequentially by four synchronized flashlamps approximately 1 ms before the pulse strikes the cold surface. Pulsed deposition maintains adequate isolation and causes line narrowing, which enhances spectral sensitivity. The efficacy of flash photolysis combined with pulsed deposition for producing and trapping transient species was demonstrated by infrated detection of CF3 (from photolysis of CF3I/Ar mixtures) and of ClCO (from photolysis of Cl2/CO/Ar mixtures). The apparatus was used to study the photolytic decomposition of gaseous tricarbonylironcyclobutadiene, C4H4Fe(CO)3. The results indicate that the primary photolytic step is not elimination of C4H4, as suggested earlier, but rather of CO.

Allamandola, Louis J.↗

NASA NTRS1994

A search for upstream pressure pulses associated with flux transfer events: An AMPTE/ISEE case study

On September 19, 1984, the Active Magnetospheric Particle Tracers Explorers (AMPTE) United Kingdom Satellite (UKS) and Ion Release Module (IRM) and International Sun Earth Explorers (ISEE) 1 and 2 spacecraft passed outbound through the dayside magnetopause at about the same time. The AMPTE spacecraft pair crossed first and were in the near-subsolar magnetosheath for more than an hour. Meanwhile the ISEE pair, about 5 R(sub E) to the south, observed flux transfer event (FTE) signatures. We use the AMPTE UKS and IRM plasma and field observations of magnetosheath conditions directly upstream of the subsolar magnetopause to check whether pressure pulses are responsible for the FTE signatures seen at ISEE. Pulses in both the ion thermal pressure and the dynamic pressure are observed in the magnetosheath early on when IRM and UKS are close to the magnetopause, but not later. These large pulses appear to be related to reconnection going on at the magnetopause nearby. AMPTE magnetosheath data far from the magnetopause do not show a pressure pulse correlation with FTEs at ISEE. Moreover, the magnetic pressure and tension effects seen in the ISEE FTEs are much larger than any pressure effects seen in the magnetosheath. A superposed epoch analysis based on small-amplitude peaks in the AMPTE magnetosheath total static pressure (nkT + B(exp 2)/2 mu(sub 0)) hint at some boundary effects, less than 5 nT peak-to-peak variations in the ISEE 1 and 2 B(sub N) signature starting about 1 min after the pressure peak epoch. However, these variations are much smaller than the standard deviations of the B(sub N) field component. Thus the evidence from this case study suggests that upstream magnetosheath pressure pulses do not give rise to FTEs, but may produce very small amplitude signatures in the magnetic field at the magnetopause.

Elphic, R. C.↗

NASA NTRS1993

Femtosecond pulses generated from a synchronously pumped chromium-doped forsterite laser

Kerr lens mode-locking (KLM) has become a standard method to produce femtosecond pulses from tunable solid state lasers. High power inside the laser resonator propagating through the laser-medium with nonlinear index of refraction, coupled with the stability conditions of the laser modes in the resonator, result in a passive amplitude modulation which explains the mechanism for pulse shortening. Recently, chromium doped forsterite was shown to exhibit similar pulse behavior. A successful attempt to generate femtosecond pulses from a synchronously pumped chromium-doped forsterite laser with intracavity dispersion compensation is reported. Stable, transform limited pulses with duration of 105 fs were routinely generated, tunable between 1240 to 1270 nm.

Seas, A.↗

NASA NTRS1995

Delta wing vortex manipulation using pulsed and steady blowing during ramp pitching

The effectiveness of steady and pulsed blowing as a method of controlling delta wing vortices during ramp pitching has been investigated in flow visualization experiments conducted in a water tunnel. The recessed angled spanwise blowing technique was utilized for vortex manipulation. This technique was implemented on a beveled 60 delta wing using a pair of blowing ports located beneath the vortex core at 40% chord. The flow was injected primarily in the spanwise direction but was also composed of a component normal to the wing surface. The location of vortex burst was measured as a function of blowing intensity and pulsing frequency under static conditions, and the optimum blowing case was applied at three different wing pitching rates. Experimental results have shown that, when the burst location is upstream of the blowing port, pulsed blowing delays vortex breakdown in static and dynamic cases. Dynamic tests verified the existence of a hysteresis effect and demonstrated the improvements offered by pulsed blowing over both steady blowing and no-blowing scenarios. The application of blowing, at the optimum pulsing frequency, made the vortex breakdown location comparable in static and ramp pitch-up conditions.

Moreira, J.↗

NASA NTRS1997

A Performance Comparison of Pulsed Plasma Thruster Electrode Configurations

Pulsed plasma thrusters are currently planned on two small satellite missions and proposed for a third. In these missions, the pulsed plasma thruster's unique characteristics will be used variously to provide propulsive attitude control, orbit raising, translation, and precision positioning. Pulsed plasma thrusters are attractive for small satellite applications because they are essentially stand alone devices which eliminate the need for toxic and/or distributed propellant systems. Pulsed plasma thrusters also operate at low power and over a wide power range without loss of performance. As part of the technical development required for the noted missions, an experimental program to optimize performance with respect to electrode configuration was undertaken. One of the planned missions will use pulsed plasma thrusters for orbit raising requiring relatively high thrust and previously tested configurations did not provide this. Also, higher capacitor energies were tested than previously tried for this mission. Multiple configurations were tested and a final configuration was selected for flight hardware development. This paper describes the results of the electrode optimization in detail.

Arrington, Lynn A.↗

NASA NTRS1999

Atmospheric Multiple Scattering Effects on GLAS Altimetry: Calculations of Single Pulse Bias - Part 1

Estimates of the effect of pulse stretching on satellite laser altimetry in particular the Geoscience Laser Altimeter System (GLAS), by cloud multiple scattering were made from an analytical method and from Monte Carlo calculations. The path delay of the return pulse was found to be largest for low-level clouds with particle radii (3-20 microns). The magnitude of the path delay was affected by several factors including cloud height, cloud optical depth, cloud particle size, particle shape, and receiver field of view. Polar aerosol and Rayleigh scattering usually added less than 1 cm to the overall path delay. Path delay estimates for all cloud conditions would be less if a simple Gaussian fit of the return pulse peak were used to measure the pulse's centroid. However, care must be taken in determining the centroid as factors such as pulse width, surface slope and the fitting method used will affect the estimate. A planned application for laser altimetry is high precision monitoring of the height change of polar ice sheets. In the absence of a correction algorithm, the required GLAS altimetry accuracies will not be achieved unless atmospheric channel information is used to remove profiles that are likely to be heavily contaminated by multiple scattering.

Duda, David P.↗

NASA NTRS1996

Pulse Shepherding in Nonlinear Fiber Optics

In a wavelength division multiplexed fiber system, where pulses on different wavelength beams may co-propagate in a single mode fiber, the cross-phase-modulation (CPM) effects caused by the nonlinearity of the optical fiber are unavoidable. In other words, pulses on different wavelength beams can interact with and affect each other through the intensity dependence of the refractive index of the fiber. Although CPM will not cause energy to be exchanged among the beams, the pulse shapes and locations on these beams can be altered significantly. This phenomenon makes possible the manipulation and control of pulses co-propagating on different wavelength beams through the introduction of a shepherd pulse at a separate wavelength. How this can be accomplished is demonstrated in this paper.

Yeh, C.↗

NASA NTRS1999

Lightning First Pulses Used in the "Last" (Time-of-Arrival) and "Atlas" (Single Station) Total Lightning Mapping Systems

The first RF pulse from "total lightning' discharges (cloud and ground flashes) has been used in different ways to locate the origin of flashes in two new types of lightning detection systems. The multisensor LASI time-of-arrival (TOA) system uses GPS timing of the first pulse. The ATLAS single sensor system uses the amplitude of the first pulse, which is invariant in magnitude and polarization for all lightning discharges, to determine distance from the sensor. It is significantly more accurate than past single sensor lightning mapping systems. The polarity of the first pulse generally identifies lightning type (IC or CG). Both systems utilize only the first pulse which makes signal processing much simpler than with previous lightning locating systems. Knowing the position where lightning begins (maximum electric fields, mixed phase hydrometeors and updrafts) is valuable for identifying convective cells producing the hazardous meteorological conditions caused by thunderstorms. It is also important for research studying thunderstorm electrification and associated microphysical problems.

Markson, Ralph↗

NASA NTRS2000

Energy Characteristics of Auroral Electron Precipitation: A Comparison of Substorms and Pressure Pulse Related Auroral Activity

The Polar Ultraviolet Imager (UVI) observes auroral responses to incident solar wind pressure pulses and interplanetary shocks such as those associated with coronal mass ejections. The arrival of a CME pressure pulse at the front of the magnetosphere results in highly disturbed geomagnetic conditions and a substantial increase in both dayside and nightside auroral precipitation. Our observations show a simultaneous brightening over broad areas of the dayside and nightside aurora in response to a pressure pulse, indicating that more magnetospheric regions participate as sources for auroral precipitation than during isolated substorms. We estimate the average energies of incident auroral electrons using Polar UVI images and compare the precipitation energies during pressure pulse associated events to those during isolated auroral substorms. Electron precipitation during substorms has average energies greater than 10 keV and is structured both in local time and magnetic latitude. For auroral intensifications following the arrival of a pressure pulse or interplanetary shock, electron precipitation is less spatially structured and has greater ux of lower energy electrons (Eave _ 7 keV) than during isolated substorm, onsets. The average energies of the precipitating electrons inferred from UVI are consistent with those measured in-situ by the FAST spacecraft. These observations quantify the differences between global and local auroral precipitation processes and will provide a valuable experimental check for models of sudden storm commencements and magnetospheric response to perturbations in the solar wind.

Chua, D.↗

NASA NTRS2001

A New Concept for Non-Volatile Memory: The Electric-Pulse Induced Resistive Change Effect in Colossal Magnetoresistive Thin Films

A novel electric pulse-induced resistive change (EPIR) effect has been found in thin film colossal magnetoresistive (CMR) materials, and has shown promise for the development of resistive, nonvolatile memory. The EPIR effect is induced by the application of low voltage (< 4 V) and short duration (< 20 ns) electrical pulses across a thin film sample of a CMR material at room temperature and under no applied magnetic field. The pulse can directly either increase or decrease the resistance of the thin film sample depending on pulse polarity. The sample resistance change has been shown to be over two orders of magnitude, and is nonvolatile after pulsing. The sample resistance can also be changed through multiple levels - as many as 50 have been shown. Such a device can provide a way for the development of a new kind of nonvolatile multiple-valued memory with high density, fast write/read speed, low power-consumption, and potential high radiation-hardness.

Liu, S. Q.↗

NASA NTRS2003

Effects of Two-Pulse Sequencing on Characteristics of Elementary Propellants for Ablative Laser Propulsion

This work continues on previous investigations of elementary propellants for Ablative Laser Propulsion (ALP). This paper details the experimental methods used for alignment of a non-colinear temporal pulse splitting apparatus. Spatial coincidence of the separate pulses is established, the pulses are delayed, and first data is reported on this pulse spacing effect on time-of-fight (TOF) measurements. This includes ion velocity and number density measurements, and this data is compared to results from a previous work. Also, first data on the experimental determination of the time required for the laser-induced plasma to become purely reflective to incident pulses is presented.

Thompson, M. Shane↗

NASA NTRS2003

A Simple Model of Pulsed Ejector Thrust Augmentation

A simple model of thrust augmentation from a pulsed source is described. In the model it is assumed that the flow into the ejector is quasi-steady, and can be calculated using potential flow techniques. The velocity of the flow is related to the speed of the starting vortex ring formed by the jet. The vortex ring properties are obtained from the slug model, knowing the jet diameter, speed and slug length. The model, when combined with experimental results, predicts an optimum ejector radius for thrust augmentation. Data on pulsed ejector performance for comparison with the model was obtained using a shrouded Hartmann-Sprenger tube as the pulsed jet source. A statistical experiment, in which ejector length, diameter, and nose radius were independent parameters, was performed at four different frequencies. These frequencies corresponded to four different slug length to diameter ratios, two below cut-off, and two above. Comparison of the model with the experimental data showed reasonable agreement. Maximum pulsed thrust augmentation is shown to occur for a pulsed source with slug length to diameter ratio equal to the cut-off value.

Wilson, Jack↗

NASA NTRS2003

Pulsed Ejector Wave Propogation Test Program

The development of, and initial test data from, a nondetonating Pulse Detonation Engine (PDE) simulator tested in the NASA Glenn 1 x 1 foot Supersonic Wind Tunnel (SWT) is presented in this paper. The concept is a pulsed ejector driven by the simulated exhaust of a PDE. This pro- gram is applicable to a PDE entombed in a ramjet flowpath, i.e., a PDE combined-cycle propulsion system. The ejector primary flow is a pulsed, uiiderexpanded, supersonic nozzle simulating the supersonic waves ema- nating from a PDE, while the ejector secondary flow is the 1 x 1 foot SWT test section operated at subsonic Mach numbers. The objective is not to study the detonation details, but the wave physics including t,he start- ing vortices, the extent of propagation of the wave front, the reflection of the wave from the secondary flowpath walls, and the timing of these events of a pulsed ejector, and correlate these with Computational Fluid Dynamics (CFD) code predictions. Pulsed ejectors have been shown to result in a 3 to 1 improvement in LID (length-to-diameter) and a near 2 to 1 improvement in thrust augmentation over a steady ejector. This program will also explore the extent of upstream interactions between an inlet and large, periodically applied, backpressures to the inlet as would be present due to combustion tube detonations in a PDE. These interactions could result in inlet unstart or buzz for a supersonic mixed compression inlet. The design of the present experiment entailed the use of an 2-t diagram characteristics code to study the nozzle filling and purging timescales as well as a series of CFD analyses conducted using the WIND code. The WIND code is a general purpose CFD code for solution of the Reynolds averaged Navier-Stokes equations and can be applied to both steady state and time-accurate calculations. The first, proof-of-concept, test entry (spring 2001) pressure distributions shown here indicate the simulation concept was successful and therefore the experimental approach is sound.

Fernandez, Rene↗