Search NASA⌕ Search

SEARCH · Search NASA

Results for “Panel method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Computing induced velocity perturbations due to a helicopter fuselage in a free stream

The velocity field of a representative helicopter fuselage in a free stream is computed. Perturbation velocities due to the fuselage are computed in a plan above the location of the helicopter rotor (rotor removed). The velocity perturbations computed by a source-panel model of the fuselage are compared with experimental measurements taken with a laser velocimeter. Three paneled fuselage models are studied: fuselage shape, fuselage shape with hub shape, and a body of revolution. The velocity perturbations computed for both fuselage shape models agree well with the measured velocity field except in the close vicinity of the rotor hub. In the hub region, without knowing the extent of separation, modeling of the effective source shape is difficult. The effects of the fuselage perturbations are not well-predicted with a simplified ellipsoid fuselage. The velocity perturbations due to the fuselage at the plane of the measurements have magnitudes of less than 8 percent of free-stream velocity. The velocity perturbations computed by the panel method are tabulated for the same locations at which previously reported rotor-inflow velocity measurements were made.

Berry, John D.↗
NASA NTRS1988

Viscous/inviscid interaction procedure for high-amplitude oscillating airfoils

A coupling procedure between an inviscid potential theoretical panel method and an unsteady interactive boundary layer calculation procedure has been developed for calculating unsteady airloads on oscillating airfoils in the high-incidence regime. A coordinate transformation into a time-dependent surface coordinate has been incorporated into the boundary layer code to avoid a quasi-steady treatment of the viscous flow equations in the leading edge region. The upper and lower sides of the airfoil are calculated with the complete set of unsteady equations. The interactive region of the boundary layer calculation can be straightforwardly extended over the complete upper surface of the airfoil while accounting for interaction areas in the region of strong adverse pressure gradients with incipient separation. Comparisons of sample calculations with experimental data show reasonably good agreement even for unsteady drag coefficients.

Geissler, W.↗
NASA NTRS1988

Emerging technology for transonic wind-tunnel-wall interference assessment and corrections

Several nonlinear transonic codes and a panel method code for wind tunnel/wall interference assessment and correction (WIAC) studies are reviewed. Contrasts between two- and three-dimensional transonic testing factors which affect WIAC procedures are illustrated with airfoil data from the NASA/Langley 0.3-meter transonic cyrogenic tunnel and Pathfinder I data. Also, three-dimensional transonic WIAC results for Mach number and angle-of-attack corrections to data from a relatively large 20 deg swept semispan wing in the solid wall NASA/Ames high Reynolds number Channel I are verified by three-dimensional thin-layer Navier-Stokes free-air solutions.

Newman, P. A.↗
NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗
NASA NTRS1990

Concurrent processing adaptation of aeroplastic analysis of propfans

Discussed here is a study involving the adaptation of an advanced aeroelastic analysis program to run concurrently on a shared memory multiple processor computer. The program uses a three-dimensional compressible unsteady aerodynamic model and blade normal modes to calculate aeroelastic stability and response of propfan blades. The identification of the computational parallelism within the sequential code and the scheduling of the concurrent subtasks to minimize processor idle time are discussed. Processor idle time in the calculation of the unsteady aerodynamic coefficients was reduced by the simple strategy of appropriately ordering the computations. Speedup and efficiency results are presented for the calculation of the matched flutter point of an experimental propfan model. The results show that efficiencies above 70 percent can be obtained using the present implementation with 7 processors. The parallel computational strategy described here is also applicable to other aeroelastic analysis procedures based on panel methods.

Janetzke, David C.↗
NASA NTRS1989

Probabilistic modeling for simulation of aerodynamic uncertainties in propulsion systems

The numerical simulation of the probabilistic aerothermodynamic response of propulsion system components to randomness in their environment was explored. The reusable rocket engine turbopumps were selected as an example because of the severe cryogenic environment in which they operate. The thermal and combustion instabilities, coupled with the engine thrust requirements from start up to shut down, lead to randomness in the flow variables and uncertainties in the aerodynamic loading. The probabilistic modeling of the turbopumps aerodynamic response was accomplished using the panel method coupled with fast probability integration methods. The aerodynamic response in the form of probabilistic rotor blades and splitter loading were predicted and the results presented for specified flow coefficient and rotor preswirl variance. Possible future applications of the aerothermodynamic probabilistic modeling in engine transient simulation, condition monitoring and engine life prediction are briefly discussed.

Hamed, Awatef↗
NASA NTRS1990

The simulation of fluid dynamic uncertainties in the SSME turbopump

The aerodynamic uncertainties in the reusable rocket engine turbopumps due to randomness in their cryogenic environment are investigated. The probabilistic simulation of the turbopumps' aerodynamic response was accomplished using the panel method coupled with Fast Probability Integration methods. The results are presented for the probabilistic rotor blades and splitter loading and their sensitivity to specified flow coefficient and rotor preswirl variance.

Hamed, Awatef↗
NASA NTRS1990

Parametric analysis of swept-wing geometry with sheared wing tips

A computational parameter study is presented of potential reductions in induced drag and increases in lateral-directional stability due to sheared wing tips attached to an untwisted wing of moderate sweep and aspect ratio. Sheared tips are swept and tapered wing-tip devices mounted in the plane of the wing. The induced-drag results are obtained using an inviscid, incompressible surface-panel method that models the nonlinear effects due to the deflected and rolled-up wake behind the lifting surface. The induced-drag results with planar sheared tips are compared to straight-tapered tip extensions and nonplanar winglet geometries. The lateral-directional static-stability characteristics of the wing with sheared tips are estimated using a quasi-vortex-lattice method. For certain combinations of sheared-tip sweep and taper, both the induced efficiency of the wing and the relevant static-stability derivatives are predicted to increase compared to the wing with a straight-tapered tip modification.

Fremaux, C. M.↗
NASA NTRS1990

Application of boundary layer control to HSCT low speed configuration

The feasibility of using boundary layer control (BLC) on a high speed civil transport (HSCT) high lift configuration for low speed performance improvement is studied. The possibility of using a part of the suction system previously designed for cruise laminar flow control (LFC) for low speed BLC mode was explored. A suction scheme for BLC was devised for the HSCT high lift configuration. The extent of the suction regions and levels were determined via panel method based inviscid flow analysis coupled with three-dimensional boundary layer analyses. The compatibility of the BLC suction requirements was assessed, and the modifications necessary to operate the system in both modes of operation, were determined. An assessment of the potential aerodynamic performance improvement resulting from an implementation of the BLC concept compared to an optimized simple flap configuration without BLC was made by an Euler code analysis of the simple flap configuration.

Parikh, P. G.↗
NASA NTRS1989

Calculation of the rotor induced download on airfoils

Interactions between the rotors and wing of a rotary wing aircraft in hover have a significant detrimental effect on its payload performance. The reduction of payload results from the wake of lifting rotors impinging on the wing, which is at 90 deg angle of attack in hover. This vertical drag, often referred as download, can be as large as 15 percent of the total rotor thrust in hover. The rotor wake is a three-dimensional, unsteady flow with concentrated tip vortices. With the rotor tip vortices impinging on the upper surface of the wing, the flow over the wing is not only three-dimensional and unsteady, but also separated from the leading and trailing edges. A simplified two-dimensional model was developed to demonstrate the stability of the methodology. The flow model combines a panel method to represent the rotor and the wing, and a vortex method to track the wing wake. A parametric study of the download on a 20 percent thick elliptical airfoil below a rotor disk of uniform inflow was performed. Comparisons with experimental data are made where the data are available. This approach is now being extended to three-dimensional flows. Preliminary results on a wing at 90 deg angle of attack in free stream is presented.

Lee, C. S.↗
NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 4: Computer user's manual for UAAP turboprop aeroacoustic code

The Unified AeroAcoustic Program (UAAP) code calculates the airloads on a single rotation prop-fan, or propeller, and couples these airloads with an acoustic radiation theory, to provide estimates of near-field or far-field noise levels. The steady airloads can also be used to calculate the nonuniform velocity components in the propeller wake. The airloads are calculated using a three dimensional compressible panel method which considers the effects of thin, cambered, multiple blades which may be highly swept. These airloads may be either steady or unsteady. The acoustic model uses the blade thickness distribution and the steady or unsteady aerodynamic loads to calculate the acoustic radiation. The users manual for the UAAP code is divided into five sections: general code description; input description; output description; system description; and error codes. The user must have access to IMSL10 libraries (MATH and SFUN) for numerous calls made for Bessel functions and matrix inversion. For plotted output users must modify the dummy calls to plotting routines included in the code to system-specific calls appropriate to the user's installation.

Menthe, R. W.↗
NASA NTRS1990

Toward the routine aerodynamic analysis of complex configurations

An evaluation is made of the ability of the TranAir CFD code to routinely compute the aerodynamic characteristics of complex subsonic and supersonic aircraft configurations. TranAir solves the full-potential equation for transonic flow about completely arbitrary geometries, using the surface-paneling PanAir technique in geometry definition. The uniform global grid may be locally refined in regions where flow properties are rapidly changing, such as regions where shocks arise, and around wing leading edges. Unlike panel method codes, TranAir solutions are not undermined by small-perturbation assumptions. Illustrative results are presented for such configurations as the F-16A with wingtip-mounted missiles and underwing fuel tanks, a generic fighter configuration, and a model of NASA-Ames' 12-ft Pressure Wind Tunnel.

Madson, Michael D.↗
NASA NTRS1991

Estimation of additive forces and moments for supersonic inlets

A technique for estimating the additive forces and moments associated with supersonic, external compression inlets as a function of mass flow ratio has been developed. The technique makes use of a low order supersonic paneling method for calculating minimum additive forces at maximum mass flow conditions. A linear relationship between the minimum additive forces and the maximum values for fully blocked flow is employed to obtain the additive forces at a specified mass flow ratio. The method is applicable to two-dimensional inlets at zero or nonzero angle of attack, and to axisymmetric inlets at zero angle of attack. Comparisons with limited available additive drag data indicate fair to good agreement.

Perkins, Stanley C., Jr.↗
NASA NTRS1991

Unsteady fluid dynamic model for propeller induced flow fields

A potential flow based three-dimensional panel method was modified to treat time dependent flow conditions in which the body's geometry may vary with time. The main objective of this effort was the study of a flow field due to a propeller rotating relative to a nonrotating body which is otherwise moving at a constant forward speed. Calculated surface pressure, thrust and torque coefficient data for a four-bladed marine propeller/body compared favorably with previously published experimental results.

Katz, Joseph↗
NASA NTRS1990

Probabilistic modeling for simulation of aerodynamic uncertainties in propulsion systems

The numerical simulation of the probabilistic aerothermodynamic response of propulsion system components to randomness in their environment was explored. The reusable rocket engine turbopumps were selected as an example because of the severe cryogenic environment in which they operate. The thermal and combustion instabilities, coupled with the engine thrust requirements from start up to shut down, lead to randomness in the flow variables and uncertainties in the aerosynamic loading. The probabilistic modeling of the turbopumps' aerodynamic response was accomplished using the panel method coupled with fast probability integration methods. The aerodynamic response in the form of probabilistic rotor blades and splitter loading were predicted and the results presented for specified flow coefficient and rotor preswirl variance. Possible future applications of the aerothermodynamic probabilistic modeling in engine transient simulation, condition monitoring, and engine life prediction are briefly discussed.

Hamed, A.↗
NASA NTRS1993

Viscous/Inviscid Interaction On An Oscillating Airfoil

Viscous/inviscid-interaction procedure developed for computation of two-dimensional flow of air about airfoil, angle of attack of which oscillates at high amplitude. Purpose of procedure to study flow effects in dynamic stall. Bulk of flow treated as inviscid, while effects of viscosity treated only on surface of airfoil and in boundary layer. Inviscid part of flow simulated via time-marching, unsteady-subsonic-flow panel method incorporating appropriate distributions of unsteady surface and wake singularities.

Carr, L. W.↗
NASA NTRS1993

Analytical and experimental studies of a short compact subsonic diffuser for a two-dimensional supersonic inlet

An experimental study of a two-dimensional supersonic inlet with a short compact subsonic diffuser, length to exit diameter (dl/d) ratio of 1.25, was conducted to investigate the impact of the short diffuser on inlet performance at low speeds and to assess the diffuser subsonic performance for a simulated diffuser flow corresponding to high-speed inlet conditions near the design flight Mach number of 2.2. For the low-speed testing, a drooped lip was employed to improve the inlet performance at a high angle of attack. For the simulated high-speed testing, air was blown through slots or discrete nozzles as an active boundary-layer control. The results from the low-speed performance test were compared with the results from a previous test program on the same inlet with a long subsonic diffuser (dl/d = 4.5). The comparison indicates that inlet recovery was not affected by the use of the short diffuser for either the baseline (no droop) or the drooped cowl lip configuration. However, the inlet baseline distortion for the short diffuser configuration was substantially higher than for the long diffuser. A comparison of the two configurations with a 70 deg drooped lip showed no significant difference in distortion. For the portion of the experimental program in which diffuser conditions for high-speed flight were simulated, diffuser-induced flow separation occurred. This separation was predicted from an analytical study that used the Hess potential flow panel method and the Herring two-dimensional boundary-layer analysis computer codes. The flow separated mainly on the diffuser ramp. Subsequent tests in which boundary-control systems were utilized showed that blowing with either slots or discrete nozzles could suppress the flow separation in the short subsonic diffuser, thereby substantially improving the diffuser performance.

Iek, Chanthy↗
NASA NTRS1993

Transition aerodynamics for 20-percent-scale VTOL unmanned aerial vehicle

An investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to establish a transition data base for an unmanned aerial vehicle utilizing a powered-lift ejector system and to evaluate alterations to the ejector system for improved vehicle performance. The model used in this investigation was a 20-percent-scale, blended-body, arrow-wing configuration with integrated twin rectangular ejectors. The test was conducted from hover through transition conditions with variations in angle of attack, angle of sideslip, free-stream dynamic pressure, nozzle pressure ratio, and model ground height. Force and moment data along with extensive surface pressure data were obtained. A laser velocimeter technique for measuring inlet flow velocities was demonstrated at a single flow condition, and also a low order panel method was successfully used to numerically simulate the ejector inlet flow.

Kjerstad, Kevin J.↗