Search NASA⌕ Search

SEARCH · Search NASA

Results for “Projection imaging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Constraints on the rate of discharge and duration of the Mangala Valles flood

Interest in Mangala Valles remains high within the planetary science community. This is justified because the survey mission images provide us with nearly complete coverage of the system at high resolution. Upcoming high resolution topography from the Mars Observer Laser Altimeter will enable the application of flood discharge models with an unprecedented level of detail. Previous work on the Mangala Valles problem has relied on the available low resolution topography. This has limited the ability of workers to constrain discharge calculations to only within several-order-of-magnitude estimates. Local determinations of channel depths via shadow length measurements and photoclinometric profiling are much more accurate, but can only be applied to steep slopes (and/or low sun elevations) in the case of shadow measurements, or across relatively short distances (to avoid changes in albedo along asymmetric photoclinometric profiles). We are taking stereo parallax measurements from medium resolution Viking Orbiter images, which provide a valuable intermediate check of the topography between those measurements made thus far and the upcoming Mars Observer data. The images used are from orbits 034A and 637A, and cover Mangala Valles from the source graben in Memnonia Fossae to the beginning of the bifurcated reach (at 9.5 deg lat., 151.5 deg lon.). These images are about 300 m/pixel and 250 m/pixel, respectively. Both sets of images were orthographically projected to 250 m/pixel. The separation angle between left-right pairs is approximately 52 degrees. This results in a vertical accuracy on the order of plus or minus 260 m. Though this is still somewhat coarse, the channel relief is clearly resolved. Preliminary profiles across Mangala Valles and the large topographic ridge to the east are shown on the following page. An east-west regional tilt that resulted from slight scaling differences in the digital data has been 'removed' by visually estimating a regional datum on the stereo pairs. North-south variations in scale have not yet been adjusted for, so the zero datum for each profile was simply taken to be the high water line of the channel itself. Our depth measurement for the source breach of about 750 m agrees reasonably well with values of 700-1000 m determined from shadow measurements.

Parker, T. J.↗
NASA NTRS1995

Effects of energy release on near field flow structure of gas jets

The primary objective is to understand how buoyancy affects the structure of the shear layer, the development of fluid dynamic instabilities, and formation of the coherent structures in the near-nozzle regions of gas jets. The secondary objectives are to study the role of buoyancy in lifting and reattachment process of diffusion flames, to evaluate the scaling behavior of diffusion flames, and to aid development and/or validation of theoretical models by providing quantitative data in the absence of buoyancy. Fast reacting hydrogen or hydrogen-inert fuels are used to isolate the effects of buoyancy on fluid dynamics without masking the flame behavior by soot and radiative heat transfer. This choice of fuel also permits an evaluation of simulating low gravity in low pressure ground experiments because the similarity constraints are relaxed for the fast reacting, nonsooting diffusion flames. The diagnostics consists primarily of a color schlieren system coupled with computer generated rainbow filters, video recording, and image analysis. The project involves (1) drop tower experiments, (2) ground experiments, and (3) theoretical analysis.

Agrawal, Ajay K.↗
NASA NTRS2003

Refinement of Protocols for Measuring the Apparent Optical Properties of Seawater

Ocean color satellite missions, like the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) or the Moderate Resolution Imaging Spectroradiometer (MODIS) projects, are tasked with acquiring a global ocean color data set, validating and monitoring the accuracy and quality of the data, processing the radiometric data into geophysical units using a set of atmospheric and bio-optical algorithms, and distributing the final products to the scientific community. The long-standing requirement of the SeaWiFS Project, for example, is to produce spectral water-leaving radiances, LW(lambda), to within 5% absolute (lambda denotes wavelength) and chlorophyll a concentrations to within 35% (Hooker and Esaias 1993), and most ocean color sensors have the same or similar requirements. Although a diverse set of activities are required to ensure the accuracy requirements are met (Hooker and McClain 2000), the perspective here is with field observations. The accurate determination of upper ocean apparent optical properties (AOPs) is essential for the vicarious calibration of ocean color data and the validation of the derived data products, because the sea-truth measurements are used to evaluate the satellite observations (Hooker and McClain 2000). The uncertainties with in situ AOP measurements have various sources: a) the sampling procedures used in the field, including the environmental conditions encountered; b) the absolute characterization of the radiometers in the laboratory; c) the conversion of the light signals to geophysical units in a processing scheme, and d) the stability of the radiometers in the harsh environment they are subjected to during transport and use. Assuming ideal environmental conditions, so this aspect can be neglected, the SeaWiFS ground-truth uncertainty budget can only be satisfied if each uncertainty is on the order of 1-2%, or what is generally referred to as 1% radiometry. In recent years, progress has been made in estimating the magnitude of some of these uncertainties and in defining procedures for minimizing them. For the SeaWiFS Project, the first step was to convene a workshop to draft the SeaWiFS Ocean Optics Protocols (hereafter referred to as the Protocols). The Protocols initially adhered to the Joint Global Ocean Flux Study (JGOFS) sampling procedures (JGOFS 1991) and defined the standards for optical measurements to be used in SeaWiFS calibration and validation activities (Mueller and Austin 1992). Over time, the Protocols were revised (Mueller and Austin 1995), and then recurringly updated on essentially an annual basis (Mueller 2000, 2002, and 2003) as part of the Sensor Inter-comparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) project. 98

Hooker, Stanford B.↗
NASA NTRSDate not supplied

Data & Reasoning Fabric (DRF) Outreach

The Data & Reasoning Fabric activity, under the Convergent Aeronautics Solutions (CAS) Project has developed images and content suitable for public outreach. Content and images are expected to be presented to National League of Cities, US Ignite, Association for Unmanned Vehicle Systems International (AUVSI), Federal Aviation Administration (FAA), cities, and local governments.

Data & Reasoning Fabric↗
NASA NTRS2022

NASA Data & Reasoning Fabric (DRF)

The Data & Reasoning Fabric activity, under the Convergent Aeronautics Solutions (CAS) Project has developed images and content for an e-brochure suitable for public outreach.

Data & Reasoning Fabric↗
NASA NTRS2022

Global geologic map of asteroid (101955) Bennu indicates heterogeneous resurfacing in the past 500,000 years

Global geologic maps are useful tools for efficient interpretation of a planetary body, and they provide global context for the diversity and evolution of the surface. We used data acquired by the OSIRIS-REx spacecraft to create the first global geologic map of the near-Earth asteroid (101955) Bennu. As this is the first geologic map of a small, non-spherical, rubble-pile asteroid, we discuss the distinctive mapping challenges and best practices that may be useful for future exploration of similar asteroids, such as those to be visited with the Hera and Janus missions. By mapping on two centimeter-scale global image mosaics (2D projected space) and a centimeter-scale global shape model (3D space), we generated three input maps respectively describing Bennu’s shape features, geologic features, and surface texture. Based on these input maps, we defined two geologic units: the Smooth Unit and the Rugged Unit. The units are differentiated primarily on the basis of surface texture, concentrations of boulders, and the distributions of lineaments, mass movement features, and craters. They are bounded by several scarps. The Rugged Unit contains abundant boulders and signs of recent mass movement. It also has fewer small(<20 m), putatively fresh craters than the Smooth Unit, suggesting that such craters have been erased in the former. Based on these geologic indicators, we infer that the Rugged Unit has the younger surface of the two. Differential crater size-frequency distributions and the distribution of the freshest craters suggest that both unit surfaces formed ~10–65 million years ago, when Bennu was located in the Main Asteroid Belt, and the Smooth Unit has not been significantly resurfaced in the past 2 million years. Meanwhile, the Rugged Unit has experienced resurfacing within the past ~500,000years during Bennu’s lifetime as a near-Earth asteroid. The geologic units are consistent with global diversity in slope, surface roughness, normal albedo, and thermal emission spectral characteristics. The site on Bennu where the OSIRIS-REx mission collected a regolith sample is located in the Smooth Unit, in a small crater nested within a larger one. So although the Smooth Unit is an older surface than the Rugged Unit, the impact-crater settingindicates that the material sampled was recently exposed. Several similarities are apparent between Bennu and asteroid (162173) Ryugu from a global geologic perspective, including two geologic units distinguishable by variations in the number density of boulders, as well as in other datasets such as brightness.

E R Jawin↗
NASA NTRS1995

Optical imaging of cloud-to-stratosphere/mesosphere lightning over the Amazon Basin (CS/LAB)

The purpose of the CS/LAB project was to obtain images of cloud to stratosphere lightning discharges from aboard NASA's DC-8 Airborne Laboratory while flying in the vicinity of thunderstorms over the Amazon Basin. We devised a low light level imaging package as an add-on experiment to an airborne Laboratory deployment to South America during May-June, 1993. We were not successful in obtaining the desired images during the South American deployment. However, in a follow up flight over the American Midwest during the night of July 8-9, 1993 we recorded nineteen examples of the events over intense thunderstorms. From the observations were estimated absolute brightness, terminal altitudes, flash duration, horizontal extents, emission volumes, and frequencies relative to negative and positive ground strokes.

Sentman, Davis D.↗
NASA NTRS1998

Clementine High Resolution Camera Mosaicking Project

This report constitutes the final report for NASA Contract NASW-5054. This project processed Clementine I high resolution images of the Moon, mosaicked these images together, and created a 22-disk set of compact disk read-only memory (CD-ROM) volumes. The mosaics were produced through semi-automated registration and calibration of the high resolution (HiRes) camera's data against the geometrically and photometrically controlled Ultraviolet/Visible (UV/Vis) Basemap Mosaic produced by the US Geological Survey (USGS). The HiRes mosaics were compiled from non-uniformity corrected, 750 nanometer ("D") filter high resolution nadir-looking observations. The images were spatially warped using the sinusoidal equal-area projection at a scale of 20 m/pixel for sub-polar mosaics (below 80 deg. latitude) and using the stereographic projection at a scale of 30 m/pixel for polar mosaics. Only images with emission angles less than approximately 50 were used. Images from non-mapping cross-track slews, which tended to have large SPICE errors, were generally omitted. The locations of the resulting image population were found to be offset from the UV/Vis basemap by up to 13 km (0.4 deg.). Geometric control was taken from the 100 m/pixel global and 150 m/pixel polar USGS Clementine Basemap Mosaics compiled from the 750 nm Ultraviolet/Visible Clementine imaging system. Radiometric calibration was achieved by removing the image nonuniformity dominated by the HiRes system's light intensifier. Also provided are offset and scale factors, achieved by a fit of the HiRes data to the corresponding photometrically calibrated UV/Vis basemap, that approximately transform the 8-bit HiRes data to photometric units. The sub-polar mosaics are divided into tiles that cover approximately 1.75 deg. of latitude and span the longitude range of the mosaicked frames. Images from a given orbit are map projected using the orbit's nominal central latitude. Polar mosaics are tiled into squares 2250 pixels on a side, which spans approximately 2.2 deg. Two mosaics are provided for each pole: one corresponding to data acquired while periapsis was in the south, the other while periapsis was in the north. The CD-ROMs also contain ancillary data files that support the HiRes mosaic. These files include browse images with UV/Vis context stored in a Joint Photographic Experts Group (JPEG) format, index files ('imgindx.tab' and 'srcindx.tab') that tabulate the contents of the CD, and documentation files.

Source record↗
NASA NTRSDate not supplied

NASA Power: Global Solar Insolation, Meteorological Parameter Data, and Web Services to Support Sustainable Building Design and Operations

The buildings industry is currently striving to adopt green solutions to make infrastructure more energy-efficient in order to meet the 2050 net-zero climate goals. This planning requires reliable environmental datasets that are crucial in designing, building, and maintaining our world’s-built environment, as well as other energy-related processes and investments. This webinar for the National Institute of Building Sciences provides an overview of NASA’s Prediction Of Worldwide Energy Resources (POWER) Project that informs decision-making and development for sustainable building design and operations by enabling public open discovery, efficient access, and convenient distribution of NASA’s Earth Observations and global atmospheric model datasets. POWER’s datastore is comprised of solar radiation and surface meteorology parameters, spanning nearly 40 years of hourly data, that are easily accessible via several access methods and tools to support three focus areas: 1) renewable energy deployment and management, 2) sustainable infrastructure, and 3) agroclimatology applications. POWER and NASA Earth Science both plan future data parameters, updated tools, and improved observations that could directly support U.S. and international sustainable development goals, climate strategies, and building information modeling. To this end, solar data from several NASA projects and meteorological data from NASA assimilation models have already been reformatted and disseminated to the public via a user-friendly web GIS-enabled based data portal through the POWER Project. POWER data is analysis-ready and accessible through an Application Programming Interface (API), ArcGIS Image Services, and the project’s Data Access Viewer enhanced (DAVe), an interactive online tool. The POWER DAVe also features data consistent with ASHRAE Climate Design Conditions and has developed web image services showing Building Climate Zones and their variability. Through those tools, the data can be downloaded into multiple formats that support the infrastructure community, including CSV and Energy Plus Weather (EPW). POWER’s entire data product catalog is available through Amazon Web Services (AWS) Open Data Registry (ODR) via a free and publicly accessible Simple Storage Service (S3). This webinar provides a full overview of the NASA POWER Project's data and services developed in collaboration with the sustainable infrastructure community. Examples of how the renewable energy and building communities have utilized POWER data products to make decisions and a preview of future data product expansion, including climate projections, and web services will also be provided. Additionally, use case stories from our broad community of users will be presented.

Paul W. Stackhouse↗
NASA NTRS1985

Optical stereo video signal processor

An otpical video signal processor is described which produces a two-dimensional cross-correlation in real time of images received by a stereo camera system. The optical image of each camera is projected on respective liquid crystal light valves. The images on the liquid crystal valves modulate light produced by an extended light source. This modulated light output becomes the two-dimensional cross-correlation when focused onto a video detector and is a function of the range of a target with respect to the stereo camera. Alternate embodiments utilize the two-dimensional cross-correlation to determine target movement and target identification.

Craig, G. D.↗
NASA NTRS2017

Image Navigation and Registration Performance Assessment Evaluation Tools for GOES-R ABI and GLM

The GOES-R Flight Project has developed an Image Navigation and Registration (INR) Performance Assessment Tool Set (IPATS) for measuring Advanced Baseline Imager (ABI) and Geostationary Lightning Mapper (GLM) INR performance metrics in the post-launch period for performance evaluation and long term monitoring. IPATS utilizes a modular algorithmic design to allow user selection of data processing sequences optimized for generation of each INR metric. This novel modular approach minimizes duplication of common processing elements, thereby maximizing code efficiency and speed. Fast processing is essential given the large number of sub-image registrations required to generate INR metrics for the many images produced over a 24 hour evaluation period. This paper describes the software design and implementation of IPATS and provides preliminary test results.

Image registration↗
NASA NTRS2017

Image Navigation and Registration Performance Assessment Evaluation Tools for GOES-R ABI and GLM

The GOES-R Flight Project has developed an Image Navigation and Registration (INR) Performance Assessment Tool Set (IPATS) for measuring Advanced Baseline Imager (ABI) and Geostationary Lightning Mapper (GLM) INR performance metrics in the post-launch period for performance evaluation and long term monitoring. IPATS utilizes a modular algorithmic design to allow user selection of data processing sequences optimized for generation of each INR metric. This novel modular approach minimizes duplication of common processing elements, thereby maximizing code efficiency and speed. Fast processing is essential given the large number of sub-image registrations required to generate INR metrics for the many images produced over a 24 hour evaluation period. This paper describes the software design and implementation of IPATS and provides preliminary test results.

image registration↗
NASA NTRS2003

IKONOS Spatial Resolution and Image Interpretability Characterization

This paper contains research from five individual projects to characterize the spatial performance of the IKONOS commercial imaging sensor. The end result of the projects is determination of the spatial image quality of IKONOS data prodicts in terms of the National Imagery Interpretability Rating Scale (NIIRS), the system Modulation Transfer Function (MTF), the system stability over the first year, the characteristics of the Space Imaging MTF Compensation (MTFC) procedure, and the application-specific capabilities of IKONOS imagery. Both panchromatic and multispectral imagery were evaluated. Major conclusions of this work are that the system was stable im imaging performance during the first year of operation, tha its MTF meets the specification for the NASA Scientific Data Purchase program, that the initial MTFC processing appears to be transposed in the in-track and the cross-track directions, that the MTFC results in a noise amplification of 2x to 4x in addition to sharpening the imagery, and that IKONOS panchromatic imagery achieves an average NIIRS rating of 4.5.

Ryan, Robert↗
NASA NTRS1998

NASA Image eXchange (NIX)

This paper discusses the technical aspects of and the project background for the NASA Image exchange (NIX). NIX, which provides a single entry point to search selected image databases at the NASA Centers, is a meta-search engine (i.e., a search engine that communicates with other search engines). It uses these distributed digital image databases to access photographs, animations, and their associated descriptive information (meta-data). NIX is available for use at the following URL: http://nix.nasa.gov./NIX, which was sponsored by NASAs Scientific and Technical Information (STI) Program, currently serves images from seven NASA Centers. Plans are under way to link image databases from three additional NASA Centers. images and their associated meta-data, which are accessible by NIX, reside at the originating Centers, and NIX utilizes a virtual central site that communicates with each of these sites. Incorporated into the virtual central site are several protocols to support searches from a diverse collection of database engines. The searches are performed in parallel to ensure optimization of response times. To augment the search capability, browse functionality with pre-defined categories has been built into NIX, thereby ensuring dissemination of 'best-of-breed' imagery. As a final recourse, NIX offers access to a help desk via an on-line form to help locate images and information either within the scope of NIX or from available external sources.

vonOfenheim. William H. C.↗
NASA NTRS2002

Method and apparatus for providing a seamless tiled display

A display for producing a seamless composite image from at least two discrete images. The display includes one or more projectors for projecting each of the discrete images separately onto a screen such that at least one of the discrete images overlaps at least one other of the discrete images by more than 25 percent. The amount of overlap that is required to reduce the seams of the composite image to an acceptable level over a predetermined viewing angle depends on a number of factors including the field-of-view and aperture size of the projectors, the screen gain profile, etc. For rear-projection screens and some front projection screens, an overlap of more than 25 percent is acceptable.

Johnson, Michael J.↗
NASA NTRS1989

Passive navigation using image irradiance tracking

Rotorcraft operating at low altitudes require navigational schemes for locating the terrain and obstacles. Due to the covert nature of missions to be accomplished, a passive navigation scheme is desirable. This paper describes the development of a passive navigation scheme combining image sequences from a vehicle mounted camera with vehicle motion variables. Geometric properties of perspective projection together with an image irradiance tracking scheme at each pixel are used to determine the range to various objects within the field-of-view. Derivation of the numerical algorithm and simulation results are given. Other applications of the proposed approach include navigation for autonomous planetary rovers and telerobots.

Menon, P. K. A.↗