Search NASA⌕ Search

SEARCH · Search NASA

Results for “REINFORCEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗

Three-Dimensional Permeability of Thick-Section Glass Fabric Reinforced Polymer Composite by Vacuum-Assisted Resin Infusion Molding

Abstract Determination of permeability of thick-section glass fabric preforms with fabric layers of different architectures is critical for manufacturing large, thick composite structures with complex geometry, such as wind turbine blades. The thick-section reinforcement permeability is inherently three-dimensional and needs to be obtained for accurate composite processing modeling and analysis. Numerical simulation of the liquid stage of vacuum-assisted resin infusion molding (VARIM) is important to advance the composite manufacturing process and reduce processing-induced defects. In this research, the 3D permeability of thick-section E-glass fabric reinforcement preforms is determined, and the results are validated by a comparison between flow front progressions from experiments and from numerical simulations using ansys fluent software. The orientation of the principal permeability axes were unknown prior to experiments. The approach used in this research differs from those in literature in that the through-thickness permeability is determined as a function of flow front positions along the principal axes and the in-plane permeabilities and is not dependent on the inlet radius. The approach was tested on reinforcements with fabric architectures which vary through-the-thickness direction, such as those in a spar cap of a wind turbine blade. The computational simulations of the flow-front progression through-the-thickness were consistent with experimental observations.

Engineering↗

Black-box optimization of CT acquisition and reconstruction parameters: a reinforcement learning approach

Protocol optimization is critical in Computed Tomography (CT) for achieving desired diagnostic image quality while minimizing radiation dose. Due to the inter-effect of influencing CT parameters, traditional optimization methods rely on the testing of exhaustive combinations of these parameters. This poses a notable limitation due to the impracticality of exhaustive parameter testing. This study introduces a novel methodology leveraging Virtual Imaging Trials (VITs) and reinforcement learning to more efficiently optimize CT protocols. Computational phantoms with liver lesions were imaged using a validated CT simulator and reconstructed with a novel CT reconstruction Toolkit. The optimization parameter space included tube voltage, tube current, reconstruction kernel, slice thickness, and pixel size. The optimization process was done using a Proximal Policy Optimization (PPO) agent which was trained to maximize the Detectability Index (d’) of the liver lesion for each reconstructed image. Results showed that our reinforcement learning approach found the absolute maximum d’ across the test cases while requiring 79.7% fewer steps compared to an exhaustive search, demonstrating both accuracy and computational efficiency, offering a efficient and robust framework for CT protocol optimization. The flexibility of the proposed technique allows for use of varying image quality metrics as the objective metric to maximize for. Our findings highlight the advantages of combining VIT and reinforcement learning for CT protocol management.

Fenwick, David [Duke University Medical Center]↗

Low-velocity repeated impact behaviors of Polymer Fiber Reinforced Plastics (PFRPs)

Modern fiber-reinforced composites have become ubiquitous across multiple industries due to their excellent weight-to-strength ratio. Typically glass or carbon fibers are widely used. While Glass or Carbon Fiber-Reinforced Plastics (GFPRs or CFPRs) have good stiffness, strength, and fatigue life, they are expensive and difficult to recycle. Researchers are exploring Polymer Fiber-Reinforced Plastics (PFRPs) as an alternative solution. PFRPs utilize polymer fibers and a polymer matrix. A wide range of materials options is available, including low-cost thermoplastics such as polyethylene or polypropylene. These thermoplastics are easy to handle and recyclable without special methods. Manufacturing parts using thermoplastics are well-established as well. However, their mechanical performances have not been extensively studied compared to GFRPs or CFRPs. This study examines the low-velocity impact resistance of PFRPs made of different thermoplastics. The low-velocity impacts are applied through a drop-weight tower. The experiment is divided into two cases: a single perforation impact and low-energy repeated impacts. Energy absorption and the number of impacts to failure are measured. The results are compared to traditional CFRPs which have a thermoset matrix. The PFRPs demonstrate energy absorption capabilities comparable to or greater than those of CFRPs with respect to specimen thickness and density. Additionally, the PFRPs show significantly higher impacts-to-failure than the CFRPs in low-energy repeated impact tests. This is particularly noteworthy considering that the PFRPs are much simpler and more economical to manufacture than CFRPs. To further

Ko, Seunghyun↗

Recyclable Cellulose Fiber Reinforced Vitrimer Composite

Vitrimer is an innovative class of polymeric materials which demonstrates traditional thermoset-like mechanical and chemical resilience while still being able to flow on demand like a traditional thermoplastic through covalently adaptive dynamic linkages. Herein, high-performance cellulose fiber reinforced vitrimer composites are developed using an epoxy-based vitrimer and natural cellulose paper. The reinforced vitrimer composite was fabricated by impregnating the porous structure of cellulose paper with two curable monomers, followed by in-situ polymerization of the monomers inside the fibrous scaffold. The introduction of hydroxyl group present on the cellulosic framework assisted in a faster topological rearrangement of the crosslinked matrix through transesterification exchange reaction, thus imparting various sought-after properties like shape recovery and recyclability via simple thermal reprocessing. Moreover, the reinforced vitrimer composite exhibits superior tensile properties as high as 90 MPa with 15-25 volume% vitrimer loading due to the interfacial adhesion via ester exchange reaction between the epoxy matrix and functionalities on the cellulosic fibers. Noteworthily, the key ingredients of the resulting composite (i.e., epoxy-based vitrimer and cellulose fibers) can be comfortably recycled without using aggressive chemical treatment, enabling composite to be easily recycled or disposed of at the end of service life and assist in reducing the subsequent manufacturing cost. This study would shed light on the development of a recyclable polymer composite with exceptional mechanical properties while simultaneously demonstrating self-healing and shape memory capabilities.

Rohewal, Sargun Singh↗

Mutual reinforcement of pathophysiological host-microbe interactions in intestinal stasis models

Chronic diseases arise when there is mutual reinforcement of pathophysiological processes that cause an aberrant steady state. Such a sequence of events may underlie chronic constipation, which has been associated with dysbiosis of the gut. In this study we hypothesized that assemblage of microbial communities, directed by slow gastrointestinal transit, affects host function in a way that reinforces constipation and further maintains selection on microbial communities. In our study, we used two models – an opioid-induced consti- pation model in mice, and a humanized mouse model where germ-free mice were colonized with stool from a patient with constipation-predominant irritable bowel syndrome (IBS-C) in humans. We examined the impact of pharmacologically (loperamide)-induced constipation (PIC) and IBS-C on the structural and functional profile of the gut microbiota. Germ-free (GF) mice were colonized with microbiota from PIC donor mice and IBS-C patients to determine how the microbiota affects the host. PIC and IBS-C promoted changes in the gut microbiota, characterized by increased relative abundance of Bacteroides ovatus and Parabacteroides distasonis in both models. PIC mice exhibited decreased luminal concentrations of butyrate in the cecum and altered metabolic profiles of the gut microbiota. Colonization of GF mice with PIC-associated mice cecal or human IBS-C fecal microbiota significantly increased GI transit time when compared to control microbiota recipients. IBS-C-associated gut microbiota also impacted colonic contractile properties. Lastly, our findings support the concept that constipation is characterized by dis- ease-associated steady states caused by reinforcement of pathophysiological factors in host-microbe interactions.

60 APPLIED LIFE SCIENCES↗

Impact of Laboratory-Accelerated Aging Methods to Study Alkali–Silica Reaction and Reinforcement Corrosion on the Properties of Concrete

This study focuses on two separate investigations of the main aging mechanisms: alkali–silica reactivity (ASR) and the corrosion of reinforcing steel (rebar) concrete, both of which may result in a premature failure to meet the serviceability or strength requirements of a concrete structure. However, these processes occur very slowly, spanning decades. The impact of direct chemical additives to fresh concrete to accelerate ASR and the corrosion of reinforcing steel on the fresh and hardened properties of the ensuing material are investigated to inform the potential use of chemicals in large-scale studies. The deterioration of reinforced concrete (RC) is determined by means of expansion, cracking, bulk diffusivity and surface resistivity measurements, and compressive, split tensile and flexural strength tests. The results indicate that the addition of sodium hydroxide and calcium chloride can effectively accelerate the crack formation and propagation in concrete due to ASR and the corrosion of rebar, respectively. The ASR-induced cracks maintained a constant crack width from 0.05 mm to 0.1 mm over the measurement period regardless of the intensity of aging acceleration. Adding 4% chloride by weight of cement for accelerating rebar corrosion resulted in an average crack that was 82% larger than in the case of ASR accelerated with the addition of sodium hydroxide. The addition of alkali resulted in an increase in early-age (7-day) strength. At a total alkali loading of 2.98 kg/m3, 3.84 kg/m3 and 5.57 kg/m3, the 28-day compressive strength of concrete decreased by 3%, 10% and 24%, respectively. Similarly, a higher early-age strength and a lower later-age strength was observed for the concrete in the presence of corrosive calcium chloride. The results from this research are expected to inform future studies on the long-term performance of RC structures under accelerated ASR and corrosion.

36 MATERIALS SCIENCE↗

Glassy interphases reinforce elastomeric nanocomposites by enhancing percolation-driven volume expansion under strain

For nearly a century, introduction of nanoparticles to elastomers has yielded extraordinarily tough nanocomposites that are critical to technologies from actuators to tires. The mechanisms by which this reinforcement occurs have nevertheless remained a central open question in material science. One widely debated hypothesis posits that strong interactions between polymer and particles induce "glassy bridges" that cement particles into a cohesive percolating network that resists elongation. Here, molecular dynamics simulations show that glassy particle shells do not primarily provide elongational cohesion. Instead, they amplify an underlying mechanism wherein competition between filler and elastomer networks causes the elastomer's volume to increase on deformation. This induces contributions from the elastomer's bulk modulus, which is of order 1000 times larger than its Young's modulus. These findings establish a unified understanding of low-strain reinforcement in filled elastomers as emanating from volumetric competition between coexisting particulate and elastomeric networks. This reframes and unifies our understanding of low-strain reinforcement, provides a clear-cut diagnostic for the presence of glassy bridging, and offers a new design principle for tough elastomeric nanocomposites.

Computational Physics (physics.comp-ph)↗

Theory of fiber reinforced materials

A unified and rational treatment of the theory of fiber reinforced composite materials is presented. Fundamental geometric and elasticity considerations are throughly covered, and detailed derivations of the effective elastic moduli for these materials are presented. Biaxially reinforced materials which take the form of laminates are then discussed. Based on the fundamentals presented in the first portion of this volume, the theory of fiber-reinforced composite materials is extended to include viscoelastic and thermoelastic properties. Thermal and electrical conduction, electrostatics and magnetostatics behavior of these materials are discussed. Finally, a brief statement of the very difficult subject of physical strength is included.

Hashin, Z.↗

Bonding of reinforced Teflon to metals

Reinforced FEP Teflon composite material is bonded to a metal substrate by applying a thin layer of copper on the metal surface and disposing irregularly shaped copper particles on the coated surface. The reinforced Teflon is then assembled in contact with the particles, and the assembly is heated under pressure at an elevated temperature below the melting point of the Teflon. A diffusion bond stronger than the reinforced Teflon component is produced, thus enabling the fabrication of self-lubricating bodies with relatively high strength.

Laiacona, F. P.↗

Analytical and experimental investigation of aircraft metal structures reinforced with filamentary composites. Phase 2: Structural fatigue, thermal cycling, creep, and residual strength

Specimens representative of metal aircraft structural components reinforced with boron filamentary composites were manufactured and tested under cyclic loading, cyclic temperature, or continuously applied loading to evaluate some of the factors that affect structural integrity under cyclic conditions. Bonded, stepped joints were used throughout to provide composite-to-metal transition regions at load introduction points. Honeycomb panels with titanium or aluminum faces reinforced with unidirectional boron composite were fatigue tested at constant amplitude under completely reversed loading. Results indicated that the matrix material was the most fatigue-sensitive part of the design, with debonding initiating in the stepped joints. However, comparisons with equal weight all-metal specimens show a 10 to 50 times improved fatigue life. Fatigue crack propagation and residual strength were studied for several different stiffened panel concepts, and were found to vary considerably depending on the configuration. Composite-reinforced metal specimens were also subjected to creep and thermal cycling tests. Thermal cycling of stepped joint tensile specimens resulted in a ten percent decrease in residual strength after 4000 cycles.

Blichfeldt, B.↗

Metal aircraft structural elements reinforced with graphite filamentary composites

Strain compatibility equations are used to evaluate the thermal stresses existing when unidirectional graphite composites are bonded to aluminum structures. Based on thermal stresses and optimum placement of the composite, skin-stringer aluminum panels are optimized for minimum weight compression panels with selective composite reinforcement. Composite reinforced skin-stringer panels are thermal cycled to determine the effect of thermal fatigue on structural integrity. Both cycled and uncycled panels are tested in compression and tension. Test results are correlated with predicted loads. Use of filamentary graphite composites is an efficient method of reinforcing metal structures, but care must be taken to minimize thermal stresses.

Berg, K. R.↗

Analytical and experimental investigation of aircraft metal structures reinforced with filamentary composites. Phase 3: Major component development

Analytical and experimental investigations, performed to establish the feasibility of reinforcing metal aircraft structures with advanced filamentary composites, are reported. Aluminum-boron-epoxy and titanium-boron-epoxy were used in the design and manufacture of three major structural components. The components were representative of subsonic aircraft fuselage and window belt panels and supersonic aircraft compression panels. Both unidirectional and multidirectional reinforcement concepts were employed. Blade penetration, axial compression, and inplane shear tests were conducted. Composite reinforced structural components designed to realistic airframe structural criteria demonstrated the potential for significant weight savings while maintaining strength, stability, and damage containment properties of all metal components designed to meet the same criteria.

Bryson, L. L.↗

Reinforced structural plastics

Reinforced polyimide structures are described. Reinforcing materials are impregnated with a suspension of polyimide prepolymer and bonded together by heat and pressure to form a cured, hard-reinforced, polyimide structure.

Lubowitz, H. R.↗

A penny-shaped crack in a filament-reinforced matrix. I - The filament model. II - The crack problem

The study deals with the elastostatic problem of a penny-shaped crack in an elastic matrix which is reinforced by filaments or fibers perpendicular to the plane of the crack. An elastic filament model is first developed, followed by consideration of the application of the model to the penny-shaped crack problem in which the filaments of finite length are asymmetrically distributed around the crack. Since the primary interest is in the application of the results to studies relating to the fracture of fiber or filament-reinforced composites and reinforced concrete, the main emphasis of the study is on the evaluation of the stress intensity factor along the periphery of the crack, the stresses in the filaments or fibers, and the interface shear between the matrix and the filaments or fibers. Using the filament model developed, the elastostatic interaction problem between a penny-shaped crack and a slender inclusion or filament in an elastic matrix is formulated.

Erdogan, F.↗

An automated program for reinforcement requirements for openings in cylindrical pressure vessels

An automated interactive program for calculating the reinforcement requirements for openings in cylindrical pressure vessels subjected to internal pressure is described. The program is written for an electronic desk top calculator. The program calculates the required area of reinforcement for a given opening and compares this value with the area of reinforcement provided by a proposed design. All program steps, operating instructions, and example problems with input and sample output are documented.

Wilson, J. F.↗

Fracture and fatigue of discontinuously reinforced copper/tungsten composites

The strength, toughness and resistance to cyclic crack propagation of composites consisting of copper reinforced with short tungsten wires of various lengths have been studied and the results compared with the behavior of continuously reinforced composites manufactured by the same method, i.e., by vacuum hot-pressing. It has been found that whereas the resistance to fatigue crack growth of continuously reinforced composites is very similar to that of continuous Al/stainless steel composites reported elsewhere, the addition of short fibers completely changes the mode of fracture, and no direct comparisons are possible. In effect, short fibers inhibit single crack growth by causing plastic flow to be distributed rather than localized, and although these composites are much less strong than continuous fiber composites, they nevertheless have much greater fatigue resistance.

Harris, B.↗

Wire-reinforced superalloys

The problems and progress encountered in developing refractory-wire-reinforced superalloys for turbojet-engine applications at operating temperature within 1000-1200 C are reviewed. Particular attention is given to the problem of the compatibility of the fiber-reinforcement wire and the superalloy matrix and to the means of improving composite properties. Fiber development is described, since fibers with better properties would result in better composite properties. Matrix composition is discussed in terms of its functions, namely to enhance compatibility and provide strength, oxidation protection, and ductility. Advantages and shortcomings of different fabrication techniques are revealed, and the current state of development of wire-reinforced composites is outlined by indicating the properties achieved. Requirements for further development of the material and for application to engineering components are set forth.

Signorelli, R. A.↗