Search NASA⌕ Search

SEARCH · Search NASA

Results for “REYNOLDS NUMBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1955

Over-All Performance of J65-B3 Turbojet Engine for Reynolds Number Indices from 0.8 to 0.2

The steady-state over-all performance characteristics of the J65-B3 turbojet engine were determined in an altitude test chamber for four exhaust-nozzle areas at Reynolds number indices of 0.8, 0.4, and 0.2. This range of Reynolds number indices corresponds to a range of altitudes from about sea level to 51,500 feet at a flight Mach number of 0.8. Generalized data are presented to allow calculation of engine performance at any flight condition corresponding to a Reynolds number index within the range investigated. Engine performance calculated from these generalized data is presented for seven altitudes over a range of flight speeds from zero to about 1100 knots. The use of an exhaust nozzle sized to give rated perforce at sea level would permit operation near the point of minimum specific fuel consumption for a wide range of flight conditions and engine speeds.

Fenn, David B.↗
NASA NTRS1972

The high Reynolds number cryogenic wind tunnel.

Theoretical considerations indicate that cooling the wind-tunnel test gas to cryogenic temperatures will provide a large increase in test Reynolds number with no increase in dynamic pressure while reducing the tunnel drive-power requirements. Studies have been made to determine the expected variations of Reynolds number and other parameters over wide ranges of Mach number, pressure, and temperature with due regard to avoiding liquefaction and adverse real-gas effects. Practical operational procedures have been developed in a low-speed prototype cryogenic wind tunnel. Aerodynamic experiments in the facility have demonstrated the theoretically predicted variations in Reynolds number and drive power. Force and moment measurements on a wing model mounted on a water-jacketed strain-gage sting balance have demonstrated the feasibility of operation of such balances in a cryogenic environment.

Goodyer, M. J.↗
NASA NTRS1978

Reynolds number and pressure gradient effects on compressible turbulent boundary layers

A detailed investigation of attached supersonic turbulent boundary layers over an extensive range of Reynolds numbers (12 x 10 to the 6th to 314 x 10 to the 6th) is presented. Experimental measurements were obtained for adverse pressure gradients ranging in magnitude from those of previous investigations to those approaching separation. The measurements include mean values of surface pressure and skin-friction, mean-flow profiles, and profiles of the three turbulent velocity fluctuation components and turbulent shear stress. Numerical solutions, employing three turbulence models of various degrees of complexity have been compared with the details of the measured flow fields. Generally, it was found that the more sophisticated turbulence models are superior to a mixing length model for predicting the Reynolds number and pressure gradient effects. However, some details of the turbulent fluctuations as well as the exact Reynolds number trends indicated by the data were not accurately predicted with any of the turbulence models considered.

Acharya, M.↗
NASA NTRS1983

Cryogenic wind tunnels for high Reynolds number testing

The present investigation has the objective to provide an overview of the development of cryogenic wind tunnels and their application to high Reynolds number testing. The current need for wind tunnels reflects the fact that many complex three-dimensional flows cannot yet be adequately dealt with analytically. Imperfections of wind tunnels are partly related to the fact that for most wind tunnel tests the Reynolds number is much too low. The best solution to this problem appears to be an operation of the tunnel at cryogenic temperatures (arbitrarily defined as temperatures of 150 K or less. In addition to decreasing the temperature, there are three other approaches for increasing the Reynolds number. These approaches include the use of a heavy gas, an increase in the model size, and an increase in pressure. Attention is given to the variable density tunnel concept, problems with high dynamic pressures, low-speed cryogenic tunnel results, transonic cryogenic tunnel tests, and the injection of liquid nitrogen into the tunnel.

Kilgore, R. A.↗
NASA NTRS1977

Transonic high Reynolds number stability and control characteristics of a 0.015-scale remotely controlled elevon model (44-0) of the space shuttle orbiter tested in calspan 8-foot TWT (LA70)

Transonic Wind Tunnel tests were run on a .015 scale model of the space shuttle orbiter vehicle in the 8-foot transonic wind tunnel. Purpose of the test program was to obtain basic shuttle aerodynamic data through a full range of elevon and aileron deflections, verification of data obtained at other facilities, and effects of Reynolds number. Tests were performed at Mach numbers from .35 to 1.20 and Reynolds numbers from 3,500,000 to 8,200,000 per foot. The high Reynolds number conditions (nominal 8,000,000/foot) were obtained using the ejector augmentation system. Angle of attack was varied from -2 to +20 degrees at sideslip angles of -2, 0, and +2 degrees. Sideslip was varied from -6 to +8 degrees at constant angles of attack from 0 to +20 degrees. Aileron settings were varied from -5 to +10 degrees at elevon deflections of -10, 0, and +10 degrees. Fixed aileron settings of 0 and 2 degrees in combination with various fixed elevon settings between -20 and +5 degrees were also run at varying angles of attack.

Parrell, H.↗
NASA NTRS2008

Turbulence Model Behavior in Low Reynolds Number Regions of Aerodynamic Flowfields

The behaviors of the widely-used Spalart-Allmaras (SA) and Menter shear-stress transport (SST) turbulence models at low Reynolds numbers and under conditions conducive to relaminarization are documented. The flows used in the investigation include 2-D zero pressure gradient flow over a flat plate from subsonic to hypersonic Mach numbers, 2-D airfoil flow from subsonic to supersonic Mach numbers, 2-D subsonic sink-flow, and 3-D subsonic flow over an infinite swept wing (particularly its leading-edge region). Both models exhibit a range over which they behave transitionally in the sense that the flow is neither laminar nor fully turbulent, but these behaviors are different: the SST model typically has a well-defined transition location, whereas the SA model does not. Both models are predisposed to delayed activation of turbulence with increasing freestream Mach number. Also, both models can be made to achieve earlier activation of turbulence by increasing their freestream levels, but too high a level can disturb the turbulent solution behavior. The technique of maintaining freestream levels of turbulence without decay in the SST model, introduced elsewhere, is shown here to be useful in reducing grid-dependence of the model's transitional behavior. Both models are demonstrated to be incapable of predicting relaminarization; eddy viscosities remain weakly turbulent in accelerating or laterally-strained boundary layers for which experiment and direct simulations indicate turbulence suppression. The main conclusion is that these models are intended for fully turbulent high Reynolds number computations, and using them for transitional (e.g., low Reynolds number) or relaminarizing flows is not appropriate.

Rumsey, Christopher L.↗
NASA NTRS2008

Turbulence Model Behavior in Low Reynolds Number Regions of Aerodynamic Flowfields

The behaviors of the widely-used Spalart-Allmaras (SA) and Menter shear-stress transport (SST) turbulence models at low Reynolds numbers and under conditions conducive to relaminarization are documented. The flows used in the investigation include 2-D zero pressure gradient flow over a flat plate from subsonic to hypersonic Mach numbers, 2-D airfoil flow from subsonic to supersonic Mach numbers, 2-D subsonic sink-flow, and 3-D subsonic flow over an infinite swept wing (particularly its leading-edge region). Both models exhibit a range over which they behave 'transitionally' in the sense that the flow is neither laminar nor fully turbulent, but these behaviors are different: the SST model typically has a well-defined transition location, whereas the SA model does not. Both models are predisposed to delayed activation of turbulence with increasing freestream Mach number. Also, both models can be made to achieve earlier activation of turbulence by increasing their freestream levels, but too high a level can disturb the turbulent solution behavior. The technique of maintaining freestream levels of turbulence without decay in the SST model, introduced elsewhere, is shown here to be useful in reducing grid-dependence of the model's transitional behavior. Both models are demonstrated to be incapable of predicting relaminarization; eddy viscosities remain weakly turbulent in accelerating or laterally-strained boundary layers for which experiment and direct simulations indicate turbulence suppression. The main conclusion is that these models are intended for fully turbulent high Reynolds number computations, and using them for transitional (e.g., low Reynolds number) or relaminarizing flows is not appropriate.

Rumsey, Christopher L.↗
NASA NTRS1972

Boundary-Layer Edge Conditions and Transition Reynolds Number Data for a Flight Test at Mach 20 (Reentry F)

A flight experiment, designated Reentry F, was conducted to measure heat-transfer rates for laminar, transitional, and turbulent boundary layers on a 5 deg half-angle cone 3.962 m (13 ft) long with a preflight nose radius of 2.54 mm (0.10 in.). Data were obtained over an altitude range from 36.58 to 18.29 km (120 000 to 60 000 ft) at a flight velocity of about 6.096 km/sec (20 000 ft/sec). The nominal values of the free-stream total enthalpy, sharp-cone Mach number, and the wall-to-total enthalpy ratio were 18 MJ/kg (8000 Btu/lb), 15, and 0.03, respectively. Calculated boundary-layer edge conditions that account for effects of the entropy layer and corresponding local transition Reynolds numbers are reported in the present paper. Fully developed turbulent flow occurred with essentially constant boundary-layer edge conditions near the sharp-cone values. Transition data were obtained with local edge Mach numbers ranging from about 5.55 to 15. Transition Reynolds numbers, based on local condition, were as high as 6.6 x 10(exp 7) with an edge Mach number of about 14.4 at an altitude of 24.38 km (80 000 ft). The transition could be correlated with previous flight data taken over a Mach number range from 3 to 12 in terms of parameters including the effects of local unit Reynolds number, boundary-layer wall-to-edge enthalpy ratio, and local Mach number.

Johnson, Charles B.↗
NASA NTRS2015

DNS/LES Simulations of Separated Flows at High Reynolds Numbers

Direct numerical simulations (DNS) and large-eddy simulations (LES) simulations of flow through a periodic channel with a constriction are performed using the dynamic Smagorinsky model at two Reynolds numbers of 2800 and 10595. The LES equations are solved using higher order compact schemes. DNS are performed for the lower Reynolds number case using a fine grid and the data are used to validate the LES results obtained with a coarse and a medium size grid. LES simulations are also performed for the higher Reynolds number case using a coarse and a medium size grid. The results are compared with an existing reference data set. The DNS and LES results agreed well with the reference data. Reynolds stresses, sub-grid eddy viscosity, and the budgets for the turbulent kinetic energy are also presented. It is found that the turbulent fluctuations in the normal and spanwise directions have the same magnitude. The turbulent kinetic energy budget shows that the production peaks near the separation point region and the production to dissipation ratio is very high on the order of five in this region. It is also observed that the production is balanced by the advection, diffusion, and dissipation in the shear layer region. The dominant term is the turbulent diffusion that is about two times the molecular dissipation.

Balakumar, P.↗
NASA NTRS1983

Experimental studies of the boundary layer on an airfoil at low Reynolds numbers

An experimental wind tunnel investigation was carried out to study the effect of laminar separation bubbles on a NACA 66(3)-018 airfoil for Reynolds numbers less than 4.0 x 10 to the 5th. Leading edge laminar separation bubbles formed for angles of attack of approximately 7 to 12 deg. To study the leading edge separation bubble more closely, hotwire anemometer measurements were made in the airfoil a Reynolds number of 8.0 x 10 to the 4th. Velocity and turbulence intensity profiles were obtained and boundary layer parameters were calculated. Frequency spectra were also calculated at key points in the airfoil boundary layer for this case. Correlation of the anemometry data with static pressure distributions, and flow visualization data provided insight into laminar separation bubble behavior at low Reynolds numbers.

Jansen, B. J., Jr.↗
NASA NTRS1990

The Stealth Biplane: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

The Stealth Biplane is conceived and constructed to serve as a remotely piloted vehicle designed to navigate a low-level figure-eight course at a target Reynolds number of 100,000. This flight vehicle will combine the latest in lightweight radio controlled hardware in conjunction with current low Reynolds number aerodynamic research to demonstrate feasible operation in a variety of applications. These potential low Reynolds number applications include high altitude atmospheric sampling, search and rescue, and even law enforcement. Design specs and fabrication technique are discussed.

Walsh, Timothy E.↗
NASA NTRS1982

The cryogenic wind tunnel for high Reynolds number testing

The development of cryogenic wind tunnels is reviewed with reference to the theory and advantages of cryogenic tunnels, problems common to wind tunnels and their solution, and application of cryogenic wind tunnels to high Reynolds number testing. It is shown that cryogenic wind tunnels can achieve full-scale Reynolds number with reasonable tunnel size, dynamic pressure, and drive power; the use of such tunnels also makes it possible to separate the effects of Reynolds number, Mach number, and aeroelasticity. Application of the cryogenic tunnel concept is illustrated by three examples, namely an atmospheric low-speed cryogenic tunnel, a 0.3-meter transonic cryogenic tunnel, and the National Transonic Facility now nearing completion.

Kilgore, R. A.↗
NASA NTRS1984

Hot wire in low Reynolds number flow

Progress reports were issued on the following experiments: (1) low Reynolds number flow phenomenon of periodic vortex shedding in the wake behind a cylinder as studied by applying the hot wire anemometer technique of flow measurement. The downstream diffusion of these shed vortices was of prime concern. An evaluation of the performance of the hot wire at low Reynolds number is also considered. (2) A brief examination of the back sections of the Wright Brothers wind tunnel circuits were conducted to establish whether or not gross flow deviations were present at corners, or turning vane regions. A calibration of the test sections was done. (3) The attractiveness of using rembedded grids for airfoil calculations modeled by the Euler equations was explored. These calculations were extended to C-type grids and then to Navier-Stokes calculations,

Kolb, M. A.↗
NASA NTRS1974

An experimental investigation of wall boundary layer transition Reynolds numbers in an expansion tube

Experimental measurements of boundary-layer transition in an expansion-tube test-gas flow are presented along with radial distributions of pitot pressure. An integral method for calculating constant Reynolds number lines for an expansion-tube flow is introduced. Comparison of experimental data and constant Reynolds number calculations has shown that for given conditions, wall boundary-layer transition occurs at a constant Reynolds number in an expansion-tube flow. Operating conditions in the expansion tube were chosen so that the effects of test-gas nonequilibrium on boundary-layer transition could be studied.

Weilmuenster, K. J.↗
NASA NTRS1976

Experimental investigation to validate use of cryogenic temperatures to achieve high Reynolds numbers in boattail pressure testing

An investigation has been conducted in the Langley 1/3 meter transonic cryogenic tunnel to validate the use of cryogenic temperatures to achieve high Reynolds numbers in nozzle boattail pressure testing. Tests were conducted at 0 degree angle of attack and at Mach numbers of 0.60, 0.85, and 0.90 on two wing-body configurations with differing boattail geometries. Test data were obtained by using two different techniques, the cryogenic method and the conventional method, to obtain the same Reynolds number. Later, the test data obtained from the two techniques on boattail pressure coefficient distributions and pressure drag coefficients were compared; results from the comparisons show excellent repeatability for all test conditions and indicate no measurable errors when using cryogenic temperatures to achieve high Reynolds numbers for nozzle boattail pressure testing.

Reubush, D. E.↗