Search NASA⌕ Search

SEARCH · Search NASA

Results for “RF Measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Measured thermal ion environment of STS-3

The Plasma Diagnostic Package (PDP) on the third Space Shuttle Flight (STS- 3) included a Bennett RF ion mass spectrometer which surveyed the positive ion composition in the vicinity of the vehicle. The ion measurements both within and exterior to the Shuttle cargo bay show the pervasive influence of the Shuttle's own gaseous emissions on its immediate plasma environment. Within the bay the ion spectrometer detected copius quantities of ions when the Shuttle was in daylight and when the gas pressure at the surface of the PDP was enhanced. In general few cases of ion detection occurred when the bay was facing toward the Shuttle wake. The plasma near the Shuttle consisted predominately of O+ (16AMU) ions and ions with atomic masses of 18, 30, 32 and 44 AMU corresponding to H2O+, NO+, O2+, and CO2+. All of these ions with the exception of H2O+ and CO2+ are expected ambient ions at the Shuttle's altitude of 240 km. During some thruster firings the 18 and 30 AMU ion concentrations detected within the bay increase by up to an order of magnitude within the 2.4 second sweep of the instrument. During these latter events the O+ distributions did not show a similar change.

Grebowsky, J. M.↗
NASA NTRS1999

Measurements of Ion Energy and Ion Flux Distributions in Inductively Coupled Plasmas in CF4/O2/Ar Mixtures

We report mass spectrometric studies of energy distributions and absolute concentrations of ions generated in CF4/O2/Ar inductively coupled rf plasmas. The ions were collected through a 100 mm orifice in the grounded and water cooled lower electrode in a GEC cell configuration. The measurements were made at gas pressures in the 10-50 mTorr range and rf coil power in the 100-300 W range. The observed ions are CF3(+), CF2(+), CF(+), C(+), F(+), COF(+), CO(+), O2(+), and O(+). The relative abundance of these ions varies with pressure and rf power. The energy distribution and absolute concentrations are correlated with electron number density and floating plasma potential measured by a compensated Langmuir probe.

Rao, M. V. V. S.↗
NASA NTRS1972

System design of the ATS-F RFI measurement experiment.

Description of the system design of an RFI measurement experiment regarding optimal sharing of the 5.925- to 6.425-GHz frequency band between the ATS-F synchronous satellite and terrestrial telecommunication systems. The parametric measurements made will include transmitted and received power levels, propagation-path loss and variations as a function of range, elevation angle, RF polarization, and geographical location of interference sources. The technical objectives of the C-band RFI experiment are outlined, a functional diagram of the total system for the RFI measurement experiment is presented, and the design features of the receiver RF and IF circuits, the filters and detectors, and the computer control are summarized. A basic RFI measurement plan is presented which defines and briefly states the measurement procedure, which involves a number of different measurement modes, each of which is described in detail.

Henry, V. F.↗
NASA NTRS1984

Mobile spectrometer measures radar backscatter

The present article is concerned with a helicopter-borne spectrometer (Heloscat), which has been developed to permit high-quality scattering measurements from a mobile platform at remote sites. The term 'spectrometer' referes to a class of scatterometers. The term 'scatterometer' is employed to denote a specialized radar for measuring scattering coefficients as a function of angle. A spectrometer, on the other hand, is a scatterometer which can measure backscatter at several frequencies. The Heloscat system is discussed, taking into account two antennas, RF hardware, and an externally mounted pendulum for angle encoding. A dual-antenna configuration is used for cross-polarized measurements, while a single-antenna system is used for like-polarized measurements. Attention is also given to oscillator characteristics, efficient data handling, and aspects of calibration.

Gogineni, S.↗
NASA NTRS2021

Predicting near-saturated hydraulic conductivity in urban soils

Pedotransfer functions (PTFs) provide point predictions of soil hydraulic properties from more readily measured soil characteristics, yet uncertainties and biases in measurement methods, sampling distributions, and boundary conditions can limit accuracy when estimating near-saturated hydraulic conductivity (K(n)). These limitations may be particularly problematic in understudied urban landscapes that often contain altered hydraulic properties. To better treat deficiencies in PTF performance, we addressed three objectives, which were to: 1) develop PTFs to predict urban K(n), 2) assess bulk density and coarse fragments as explanatory variables; and 3) evaluate the predictive capability of these PTFs by comparing their output to measured hydraulic conductivity values from three other studies of urban soil hydraulics. We used artificial neural networks (ANN) and random forest (RF) approaches to predict urban K(n), with the training dataset including 307 tension infiltrometer tests and other measurements drawn from urban soil assessments in 11 U.S. cities. The PTFs utilized a hierarchy of inputs, starting with percentage sand, silt, clay, and then adding percentage coarse fragments and bulk density. The ANN models performed similar to the RF models, and all models exhibited similar or better predictive performance as models results collected from published articles. The inclusion of bulk density or coarse fragments did not improve accuracy over soil texture alone. Possible reasons for this result include low correlation between K(n) and bulk density and the exclusion of large voids during flow measurements with tension infiltrometers. The models have been made available as an open-source software package to encourage adoption by users working in urban systems.

Jinshi Jian↗
NASA NTRS1981

Investigation of semiconductor clad optical waveguides

The properties of semiconductor-clad optical waveguides based on glass substrates were investigated. Computer modeling studies on four-layer silicon-clad planar dielectric waveguides indicated that the attenuation and mode index should behave as exponentially damped sinusoids as the silicon thickness is decreased below one micrometer. This effect can be explained as a periodic coupling between the guided modes of the lossless structure and the lossy modes supported by the high refractive index silicon. The computer studies also show that both the attenuation and mode index of the propagating mode are significantly altered by conductivity charges in the silicon. Silicon claddings were RF sputtered onto AgNO3-NaNO3 ion exchanged waveguides and preliminary measurements of attenuation were made. An expression was developed which predicts the attenuation of the silicon clad waveguide from the attenuation and phase characteristics of a silicon waveguide. Several applications of these clad waveguides are suggested and methods for increasing the photo response of the RF sputtered silicon films are described.

Batchman, T. E.↗
NASA NTRS1991

Characterization of NbN films and tunnel junctions

Properties of NbN films and NbN/MgO/NbN tunnel junctions are discussed. NbN junctions are being developed for use in high-frequency, SIS quasiparticle mixers. To properly design mixer circuits, junction and film properties need to be characterized. The specific capacitance of NbN/MgO/NbN junctions has been measured as a function of the product of the normal-state resistance and the junction area (RnA), and it is found to vary by more than a factor of two (35-85 fF/sq microns) over the range of RnA measured (1000-50 ohm sq microns). This variation is important because the specific capacitance determines the RC speed of the tunnel junction at a given RnA value. The magnetic penetration depth of NbN films deposited under different conditions is also measured. The magnetic penetration depth affects the design of microstrip line used in RF tuning circuits. Control of the magnetic penetration depth is necessary to fabricate reproducible tuning circuits. Additionally, the critical current uniformity for arrays of 100 junctions has been measured. Junction uniformity will affect the design of focal-plane arrays of SIS mixers. Finally, the relevance of these measurements to the design of Josephson electronics is discussed.

Stern, J. A.↗
NASA NTRS1981

Station stability measurement

Methods and instrumentation are being developed to determine the frequency stability of Deep Space Stations. The efforts are presently focused on the verification of the stability of the X-band uplink and other RF and microwave subsystems which contribute to the overall stability of the system. The measurement methodology is presented as well as frequency stability data generated with the development measurement system. The system characteristics are highlighted and the potential areas where improvements could be made are discussed.

Sosa, E. N.↗
NASA NTRS1988

Fine structure in RF spectra of lightning return stroke wave forms

The power spectra of the wide-band (10 Hz to 100 kHz) magnetic-field signals for a number of lightning return strokes measured during a thunderstorm which occurred in Lindau in August, 1984 have been calculated. The RF magnetic field data are obtained with the engineering unit of the Galileo Jupiter Probe lightning experiment. Each return stroke data stream is passed through an adaptive filter designed to whiten its spectrum. The spectra of the magnetic field data definitely show fine structure, with two or three distinct peaks in the spectra of many of the waveforms. A peak at f of about 60-70 kHz is often seen in the power spectra of the waveform time segments preceding and following the rise-to-peak amplitude of the return stroke.

Lanzerotti, L. J.↗
NASA NTRS1975

An investigation of errors and data processing techniques for an RF multilateration system

The development of an RF Multilateration system to provide accurate position and velocity measurements during the approach and landing phase of Vertical Takeoff Aircraft operation is discussed. The system uses an angle-modulated ranging signal to provide both range and range rate measurements between an aircraft transponder and multiple ground stations. Range and range rate measurements are converted to coordinate measurements and the coordinate and coordinate rate information is transmitted by an integral data link to the aircraft. Data processing techniques are analyzed to show advantages and disadvantages. Error analyses are provided to permit a comparison of the various techniques.

Britt, C. L., Jr.↗
NASA NTRS1975

Modeling damaged wings: Element selection and constraint specification

The NASTRAN analytical program was used for structural design, and no problems were anticipated in applying this program to a damaged structure as long as the deformations were small and the strains remained within the elastic range. In this context, NASTRAN was used to test three-dimensional analytical models of a damaged aircraft wing under static loads. A comparison was made of calculated and experimentally measured strains on primary structural components of an RF-84F wing. This comparison brought out two sensitive areas in modeling semimonocoque structures. The calculated strains were strongly affected by the type of elements used adjacent to the damaged region and by the choice of multipoint constraints sets on the damaged boundary.

Stronge, W. J.↗
NASA NTRS1989

Carbon-14 activities in recently fallen meteorites and Antarctic meteorites

This paper reports C-14 measurements in meteorites using an extraction method which employs RF melting of samples as small as 0.1 g. A study of extraction of cosmic-ray-produced C-14 in samples of Bruderheim gave C-14 levels between 38 and 60 dpm/kg for samples which had been preheated in air between 250 and 700 C, with a mean value of 46.8 + or - 1.4 dpm/kg. A range of values between 35 and 59 dpm/kg was found for other falls of saturated meteorites preheated to 500 C. The preheating step is shown to be effective in removing terrestrial carbon contamination. A series of samples previously dated by Kr-81 as having ages of 120-310 kyr gave C-14 levels of between less than 0.16 and 0.37 + or - 0.10 dpm/kg. These levels are consistent with levels of in situ production by cosmic rays at the earth's surface.

Jull, A. J. T.↗
NASA NTRS1992

Analysis and applications of a general boresight algorithm for the DSS-13 beam waveguide antenna

A general antenna beam boresight algorithm is presented. Equations for axial pointing error, peak received signal level, and antenna half-power beamwidth are given. A pointing error variance equation is derived that illustrates the dependence of the measurement estimation performance on the various algorithm inputs, including RF signal level uncertainty. Plots showing pointing error uncertainty as function of algorithm inputs are presented. Insight gained from the performance analysis is discussed in terms of its application to the areas of antenna controller and receiver interfacing, pointing error compensation, and antenna calibrations. Current and planned applications of the boresight algorithm, including its role in the upcoming Ka-band downlink experiment (KABLE), are highlighted.

Alvarez, L. S.↗
NASA NTRS1993

Lower Extremity Muscle Thickness During 30-Day 6 degrees Head-Down Bed Rest with Isotonic and Isokinetic Exercise Training

Muscle thickness was measured in 19 Bed-Rested (BR) men (32-42 year) subjected to IsoTonic (ITE, cycle orgometer) and IsoKi- netic (IKE, torque orgometer) lower extremity exercise training, and NO Exercise (NOE) training. Thickness was measured with ultrasonography in anterior thigh-Rectus Femoris (RF) and Vastus Intermadius (VI), and combined posterior log-soleus, flexor ballucis longus, and tibialis posterior (S + FHL +TP) - muscles. Compared with ambulatory control values, thickness of the (S + FHL + TP) decreased by 90%-12% (p less than 0.05) In all three test groups. The (RF) thickness was unchanged in the two exercise groups, but decreased by 10% (p less than 0.05) in the NOE. The (VI) thickness was unchanged In the ITE group, but decreased by 12%-l6% (p less than 0.05) in the IKE and NOE groups. Thus, intensive, alternating, isotonic cycle ergometer exercise training is as effective as intensive, intermittent, isokinetic exercise training for maintaining thicknesses of rectus femoris and vastus lntermedius anterior thigh muscles, but not posterior log muscles, during prolonged BR deconditioning.

Ellis, S.↗
NASA NTRS1999

RF Transmission Lines on Silicon Substrates

A review of RF transmission lines on silicon substrates is presented. Through measurements and calculated results, it is shown that attenuation is dominated by conductor loss if silicon substrates with a resistivity greater than 2500 Ohm-cm are used. Si passivation layers affect the transmission line attenuation; however, measured results demonstrate that passivation layers do not necessarily increase attenuation. If standard, low resistivity Si wafers must be used, alternative transmission lines such as thin film microstrip and Co-Planar Waveguide (CPW) on thick polyimide layers must be used. Measured results presented here show that low loss per unit length is achievable with these transmission lines.

Ponchak, George E.↗
NASA NTRS1994

Advanced Biotelemetry Systems for Space Life Sciences

The Sensors 2000! Program at NASA-Ames Research Center is developing an Advanced Biotelemetry System (ABTS) for Space Life Sciences applications. This modular suite of instrumentation is planned to be used in operational spaceflight missions, ground-based research and development experiments, and collaborative, technology transfer and commercialization activities. The measured signals will be transmitted via radio-frequency (RF), electromagnetic or optical carriers and direct-connected leads to a remote ABTS receiver and data acquisition system for data display, storage, and transmission to Earth. Intermediate monitoring and display systems may be hand held or portable, and will allow for personalized acquisition and control of medical and physiological data.

Hines, John W.↗
NASA NTRSDate not supplied

Examination of Mars2020 Shock-Layer Conditions via Infrared Laser Absorption Spectroscopy of CO2 and CO

Amid-infrared laser absorption diagnostic was deployed to study a simulated Mars2020 shock layer in the Electric Arc Shock Tube (EAST) facility at NASA’s Ames Research Center. Rapid RF-diplexing techniques enabled quantitative temperature and number density measurements of CO2 and CO with μs-resolution over an incident shock velocity range of 1.39 – 3.75 km/s. Two interband cascade lasers were utilized at 4.17 and 4.19 μm to resolve eight CO2 asymmetric stretch fundamental band (𝜈3) transitions from two different vibrational levels: 0000 (ground state) and 0110 (first excited bending mode). The probed rotational levels span across J” = 58 to J” = 140. Results are compared to DPLR simulations of the shock layer using kinetic mechanisms of Johnston et al. and Cruden et al. At shock velocities below 3.1 km/s, the agreement between the measurements and the Johnston mechanism is typically within 5% for temperature and within 10% for number density. At shock velocities above 3.1 km/s, the CO2 measurement becomes sensitive to a thin boundary layer and corrections of this effect are presented. On test cases with enough energy to dissociate CO2, a quantum cascade laser scanned the P(2, 20), P(0, 31), and P(3, 14) transitions of the CO fundamental band at 4.98 μm. CO formation rate is measured to be close to the Johnston kinetic mechanism at low velocities, and then trending towards the Cruden kinetic mechanism at high velocities. On a few low velocity test cases, rovibrational relaxation of the Martian atmosphere is probed with μs resolution.

Laser Absorption↗
NASA NTRS2012

Strut Shaping of 34m Beam Waveguide Antenna for Reductions in Near-Field RF and Noise Temeperature

Struts shaping of the NASA's Deep Space Network (DSN) 34m Beam Waveguide (BWG) antenna has been implemented to reduce near-field RF exposure while improving the antenna noise temperature. Strut shaping was achieved by introducing an RF shield that does not compromise the structural integrity of the existing structure. Reduction in the RF near-field exposure will compensate for the planned transmit power increase of the antenna from 20 kW to 80 kW while satisfying safety requirements for RF exposure. Antenna noise temperature was also improved by as much as 1.5 K for the low elevation angles and 0.5 K in other areas. Both reductions of RF near-field exposure and antenna noise temperature were verified through measurements and agree very well with calculated results.

reflector↗