Search NASA⌕ Search

SEARCH · Search NASA

Results for “RUDDERS - DEFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1941

Supplement to Comparison of automatic control systems

This analysis deals with the indirect regulator, wherefrom the behavior of the direct regulator is deduced as a limiting case. The prime mover is looked upon as "independent of the load": a change in the adjusting power (to be applied) for the control link (as, for example, in relation to the adjusting path (eta) with pressure valves or the rudder of vessels) does not modify the actions of the prime mover. Mass forces and friction are discounted; "clearance" also is discounted in the transmission links of the regulator.

Oppelt, W↗
NASA NTRS1931

Combined pitching and yawing motion of airplanes

This report treats the following problems: The beginning of the investigated motions is always a setting of the lateral controls, i.e., the rudder or the ailerons. Now, the first interesting question is how the motion would proceed if these settings were kept unchanged for some time; and particularly, what upward motion would set in, how soon, and for how long, since therein lie the dangers of yawing. Two different motions ensue with a high rate of turn and a steep down slope of flight path in both but a marked difference in angle of attack and consequently different character in the resultant aerodynamic forces: one, the "corkscrew" dive at normal angle, and the other, the "spin" at high angle.

Baranoff, A V↗
NASA NTRS1930

Determination of the Maximum Control Forces and Attainable Quickness in the Operation of Airplane Controls

This report is intended to furnish bases for load assumptions in the designing of airplane controls. The maximum control forces and quickness of operation are determined. The maximum forces for a strong pilot with normal arrangement of the controls is taken as 1.25 times the mean value obtained from tests with twelve persons. Tests with a number of persons were expected to show the maximum forces that a man of average strength can exert on the control stick in operating the elevator and ailerons and also on the rudder bar. The effect of fatigue, of duration and of the nature (static or dynamic) of the force, as also the condition of the test subject (with or without belt) were also considered.

Hertel, Heinrich↗
NASA NTRS1930

Calculation of Pressure Distribution on Airship Hulls

These calculations were based on the shape of the ZR III, with the following simplifications: cars, fins, and rudders removed; all cross sections replaced by equivalent circular cross sections. Under these assumptions the pressure distribution was calculated for the following cases: symmetrical case, or flow parallel to the axis; unsymmetrical case, or flow at an angle to the axis. In both cases the simple potential flow first forms the basis for the determination of the pressure distribution.

Von Karman, Theodor↗
NASA NTRS1930

Balanced and servo control surfaces

Many reports on various control systems are available, but the results cannot be generally applied since the effect of particular changes of surface-form and mounting are subject to variations depending upon airfoil section and influences of airplane layout. This report presents a simple analysis of several control systems in more general use. Elevators, ailerons, and rudders are all discussed.

Source record↗
NASA NTRS1993

Apparatus and method for improving spin recovery on aircraft

Previous research on airplane spinning and recovery has shown that at potential spin conditions (high angles of attack with rotation) the horizontal tail, depending upon its location, can create a wake about the vertical tail and rudder which can adversely affect airplane spin and recovery characteristics. Many methods of altering the tail geometry to modify these interference effects were investigated for improving airplane spin and recovery characteristics. Examples of changes includes relocation of the horizontal tail, increasing control surface travel, and use of a 'flip tail' that can be rotated to extreme angles for spin recovery. A device is provided which improves the spin recovery characteristics of aircraft which involves attaching the horizontal tail of the aircraft to the aircraft such that a gap remains between the root end of each horizontal tail section and the fuselage or vertical tail of the aircraft. The gaps measure between about 15 and 30 percent of the tail semispan. The gaps may be covered by shields which are released should a spin occur.

Stough, H. Paul, II↗
NASA NTRS1993

Aircraft empennage structural detail design

This project involved the detailed design of the aft fuselage and empennage structure, vertical stabilizer, rudder, horizontal stabilizer, and elevator for the Triton primary flight trainer. The main design goals under consideration were to illustrate the integration of the control systems devices used in the tail surfaces and their necessary structural supports as well as the elevator trim, navigational lighting system, electrical systems, tail-located ground tie, and fuselage/cabin interface structure. Accommodations for maintenance, lubrication, adjustment, and repairability were devised. Weight, fabrication, and (sub)assembly goals were addressed. All designs were in accordance with the FAR Part 23 stipulations for a normal category aircraft.

Meholic, Greg↗
NASA NTRS1993

Cockpit control system conceptual design

The purpose of this project was to provide a means for operating the ailerons, elevator, elevator trim, rudder, nosewheel steering, and brakes in the Triton primary flight trainer. The main design goals under consideration were to illustrate system and subsystem integration, control function ability, and producibility. Weight and maintenance goals were addressed.

Meholic, Greg↗
NASA NTRS1994

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Ware, George M.↗
NASA NTRS1993

Cockpit control system

The purpose of this project is to provide a detail design for the cockpit control system of the Viper PFT. The statement of work for this project requires provisions for control of the ailerons, elevator, rudder, and elevator trim. The system should provide adjustment for pilot stature, rigging, and maintenance. MIL-STD-1472 is used as a model for human factors criterion. The system is designed to the pilot limit loading outlined in FAR part 23.397. The general philosophy behind this design is to provide a simple, reliable control system which will withstand the daily abuse that is experienced in the training environment without excessive cost or weight penalties.

Lesnewski, David↗
NASA NTRS1993

The Bunny: A simulated commercial air transportation study

The Bunny is a single-engine, 100 passenger commercial transport designed to serve the high density short-to-medium range markets in AEROWORLD. The aircraft's design range is 10,000 feet at a cruise velocity of 30 ft/s. The aircraft features a low wing which incorporates polyhedral for roll control. Yaw and pitch control are accomplished by a rudder and elevator, respectively. Propulsion is provided by a nose-mounted Astro 15 electric motor powered by thirteen 1.2 V, 1000 mah batteries with a Zinger 12-6 propeller. The aircraft is structurally designed with a safety factor of 1.5 and is constructed primarily of balsa, bass, and birch wood. Passenger seating is arranged on two levels, with three-abreast on the lower level and two-abreast on the upper level. The factors which had the most significant influence on the final design were the direct operating cost and the take-off distance. The primary strength of The Bunny is its ability to compete economically with the HB-40. At full capacity and mid-range fuel costs, the cost per seat per thousand feet (CPSK) of this aircraft is 25% less than the HB-40. Another principal strength is its ability to operate in all airports in AEROWORLD. Also, The Bunny's two-piece removable wing is an advantage from a transportability standpoint.

Fulton, David↗
NASA NTRS1994

Controls design with crossfeeds for hovering rotorcraft using quantitative feedback theory

This work is extending the research accomplished on project NCC2-751. A newly implemented helicopter model has been used to simulate 25 flight configurations near hover for the UH-60 RASCAL aircraft. A new engine model has been installed in the FORECAST simulation (alias UMGENHEL) for the better prediction of the yaw and heave responses. By applying the decoupling metric from project NCC 751 it was determined that the aileron to pitch and the elevator to yaw responses do not indicate the need for crossfeeds since both of them have a decoupling metric value over 20 dB (less than 10 percent coupling). In the case of the aileron to heave and the elevator to heave responses, the large size and the overlapping of the templates indicate that a low-order dynamic crossfeed cannot be found. The low-order dynamic crossfeed selection is proceeding, however, for the remaining eight crossfeeds. Note that most of them have successfully decoupled the system by 20 dB or more, except for the rudder to heave crossfeed (18.2 dB). It is probable that the engine model needs more accuracy to further improve the heave to yaw crossfeed decoupling metric value. To see how the new low-order dynamic crossfeeds perform, a simulation was accomplished using MATLAB SIMULINK.

Biezad, Daniel J.↗
NASA NTRS1992

ANOPP/VMS HSCT ground contour system

This viewgraph shows the integration of the Visual Motion Simulator with ANOPP. ANOPP is an acronym for the Aircraft NOise Prediction Program. It is a computer code consisting of dedicated noise prediction modules for jet, propeller, and rotor powered aircraft along with flight support and noise propagation modules, all executed under the control of an executive system. The Visual Motion Simulator (VMS) is a ground based motion simulator with six degrees of freedom. The transport-type cockpit is equipped with conventional flight and engine-thrust controls and with flight instrument displays. Control forces on the wheel, column, and rudder pedals are provided by a hydraulic system coupled with an analog computer. The simulator provides variable-feel characteristics of stiffness, damping, coulomb friction, breakout forces, and inertia. The VMS provides a wide range of realistic flight trajectories necessary for computing accurate ground contours. The NASA VMS will be discussed in detail later in this presentation. An equally important part of the system for both ANOPP and VMS is the engine performance. This will also be discussed in the presentation.

Rawls, John, Jr.↗
NASA NTRS1994

Fusion interfaces for tactical environments: An application of virtual reality technology

The term Fusion Interface is defined as a class of interface which integrally incorporates both virtual and nonvirtual concepts and devices across the visual, auditory, and haptic sensory modalities. A fusion interface is a multisensory virtually-augmented synthetic environment. A new facility has been developed within the Human Engineering Division of the Armstrong Laboratory dedicated to exploratory development of fusion interface concepts. This new facility, the Fusion Interfaces for Tactical Environments (FITE) Facility is a specialized flight simulator enabling efficient concept development through rapid prototyping and direct experience of new fusion concepts. The FITE Facility also supports evaluation of fusion concepts by operation fighter pilots in an air combat environment. The facility is utilized by a multidisciplinary design team composed of human factors engineers, electronics engineers, computer scientists, experimental psychologists, and oeprational pilots. The FITE computational architecture is composed of twenty-five 80486-based microcomputers operating in real-time. The microcomputers generate out-the-window visuals, in-cockpit and head-mounted visuals, localized auditory presentations, haptic displays on the stick and rudder pedals, as well as executing weapons models, aerodynamic models, and threat models.

Haas, Michael W.↗
NASA NTRS1994

The Development of a Highly Reliable Power Management and Distribution System for Civil Transport Aircraft

NASA is pursuing a program in Advanced Subsonic Transport (AST) to develop the technology for a highly reliable Fly-By-Light/Power-By-WIre aircraft. One of the primary objectives of the program is to develop the technology base for confident application of integrated PBW components and systems to transport aircraft to improve operating reliability and efficiency. Technology will be developed so that the present hydraulic and pneumatic systems of the aircraft can be systematically eliminated and replaced by electrical systems. These motor driven actuators would move the aircraft wing surfaces as well as the rudder to provide steering controls for the pilot. Existing aircraft electrical systems are not flight critical and are prone to failure due to Electromagnetic Interference (EMI) (1), ground faults and component failures. In order to successfully implement electromechanical flight control actuation, a Power Management and Distribution (PMAD) System must be designed having a reliability of 1 failure in 10(exp +9) hours, EMI hardening and a fault tolerance architecture to ensure uninterrupted power to all aircraft flight critical systems. The focus of this paper is to analyze, define, and describe technically challenging areas associated with the development of a Power By Wire Aircraft and typical requirements to be established at the box level. The authors will attempt to propose areas of investigation, citing specific military standards and requirements that need to be revised to accommodate the 'More Electric Aircraft Systems'.

Coleman, Anthony S.↗
NASA NTRS1994

The Elite: A high speed, low-cost general aviation aircraft for Aeroworld

The Elite is a six passenger, general aviation aircraft targeted at the upper middle class private pilot. The Elite is a low wing, conventional monoplane utilizing rudder, ailerons, and a stabilator. The Elite will create a new class of aircraft in Aeroworld. This class of aircraft will demonstrate a substantial improvement in cruise speed over the current existing commercial fleet of aircraft in Aeroworld. This new class will be capable of servicing all existing airstrips in Aeroworld, including rough and short airways. The drivers of this design were aesthetics, a high cruise speed, and take-off distance.

Rueter, Amy↗
NASA NTRS1995

Flight test of the X-29A at high angle of attack: Flight dynamics and controls

The NASA Dryden Flight Research Center has flight tested two X-29A aircraft at low and high angles of attack. The high-angle-of-attack tests evaluate the feasibility of integrated X-29A technologies. More specific objectives focus on evaluating the high-angle-of-attack flying qualities, defining multiaxis controllability limits, and determining the maximum pitch-pointing capability. A pilot-selectable gain system allows examination of tradeoffs in airplane stability and maneuverability. Basic fighter maneuvers provide qualitative evaluation. Bank angle captures permit qualitative data analysis. This paper discusses the design goals and approach for high-angle-of-attack control laws and provides results from the envelope expansion and handling qualities testing at intermediate angles of attack. Comparisons of the flight test results to the predictions are made where appropriate. The pitch rate command structure of the longitudinal control system is shown to be a valid design for high-angle-of-attack control laws. Flight test results show that wing rock amplitude was overpredicted and aileron and rudder effectiveness were underpredicted. Flight tests show the X-29A airplane to be a good aircraft up to 40 deg angle of attack.

Bauer, Jeffrey E.↗
NASA NTRS1992

Application of damage tolerance methodology in certification of the Piaggio P-180 Avanti

The Piaggio P-180 Avanti, a twin pusher-prop engine nine-passenger business aircraft was certified in 1990, to the requirements of FAR Part 23 and Associated Special Conditions for Composite Structure. Certification included the application of a damage tolerant methodology to the design of the composite forward wing and empennage (vertical fin, horizontal stabilizer, tailcone, and rudder) structure. This methodology included an extensive analytical evaluation coupled with sub-component and full-scale testing of the structure. The work from the Damage Tolerance Analysis Assessment was incorporated into the full-scale testing. Damage representing hazards such as dropped tools, ground equipment, handling, and runway debris, was applied to the test articles. Additional substantiation included allowing manufacturing discrepancies to exist unrepaired on the full-scale articles and simulated bondline failures in critical elements. The importance of full-scale testing in the critical environmental conditions and the application of critical damage are addressed. The implication of damage tolerance on static and fatigue testing is discussed. Good correlation between finite element solutions and experimental test data was observed.

Johnson, Jerry↗