Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reactor Kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Plasma-Coupled Flow Reactor Studies of Low-Temperature Plasma Assisted Kinetics of Methanol Blended with CO2

Ignition technologies based on low-temperature plasmas (LTP) have the potential to operate next generation engines at elevated pressures and increased dilution limits promoting higher efficiencies. From a practical standpoint, research on LTP igniters has shown to enhance combustion and ignition, improve flame stability, and extend the dilution limits of combustion. All of the aforementioned gains are complemented with higher ignition efficiencies. However, the biggest challenge with incorporating this technology into engines is the knowledge gap of how exactly plasma chemistry effects can enhance the basic combustion phenomena. This coupled with the lack of validated kinetic mechanisms for plasma-combustion chemistry is the biggest obstruction to recognize efficient ignition, especially for application relevant fuels and biofuels. In order to comprehensively evaluate the effects of LTP on an oxygenated fuel specific system, this present study examines the kinetics of methanol plasma-assisted pyrolysis and oxidation using a custom-built plasma flow reactor (PFR). Experimental regimes are also further extended to understand the effects of adding CO2 to the mixture and its consequence on reaction kinetics. The PFR is installed with a dielectric-barrier discharge (DBD) configuration to induce LTP into the fuel mixture. Non-equilibrium plasmas are generated by high-voltage pulses (nearing 20 KV) administered by a plasma pulser at high-pulse repetition rates (up to 10 kHz). In order to better understand and isolate plasma chemistry and its effect on neutral chemistry, the experiments were carried out by heavily diluting reactive mixtures in nitrogen at near isothermal conditions. This suppresses the effect of exothermic reactions on chemistry allowing stable intermediates and products to be detected and quantified using ex-situ GC/MS diagnostic methods. Experiments were carried out at 0.5 atm pressure and over a wide range of temperatures from 523 K to 1203 K. Experimental results depicted the enhancement in intermediates production as well as overall lower temperatures required for complete fuel consumption in the plasma specific cases as opposed to their pure thermal counterpart. Formation of oxygenated and nitrile compounds specific to plasma assisted pyrolysis cases illustrated the efficacy of LTP to introduce new reaction pathways accelerating fuel decomposition. Increase in reactivity at lower temperatures is sought to be an effect induced by plasma chemistry postulating the acceleration in intermediates production. The onset of thermal ignition in plasma assisted oxidation is seen 200 K earlier than thermal oxidation highlighting efficient fuel conversion to final byproducts. Enhanced collisional processes afforded by LTP is seen to perturb reaction pathways between oxygenated fuel radicals and N-atoms to alter overall chemical reactivity. New insights into kinetics are gained from this study highlighting governing plasma assisted combustion (PAC) pathways for oxygenated fuel reaction chemistry. The results from this study can be used to develop future mechanisms specific to plasma chemistry which can bridge the mechanistic knowledge gap for LTP ignition so that future engines can adopt LTPs in their design for efficient combustion.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

An improved external recycle reactor for determining gas-solid reaction kinetics

These improvements in the recycle system effectively eliminate initial concentration variation by two modifications: (1) a vacuum line connection to the recycle loop which permits this loop to be evacuated and then filled with the test gas mixture to slightly above atmospheric pressure; and (2) a bypass line across the reactor which permits the reactor to be held under vacuum while the rest of the recycle loop is filled with test gas. A three-step procedure for bringing the feed gas mixture into contact with the catalyst at time zero is described.

Miller, Irvin M.↗

Development of hydrothermal corrosion model and BWR metal coating for CVD SiC in light water reactors

SiC/SiC fiber composites with CVD SiC overcoats are potential candidates for light water reactor advanced accident tolerant cladding materials. Understanding its corrosion kinetics in Light Water Reactor (LWR) conditions is essential to evaluate the concept's viability. Existing models only account for the temperature and oxygen concentration effect on the hydrothermal corrosion behavior applicable to LWR operating conditions. However, the development of a general corrosion rate for CVD SiC that accounts for the impact of irradiated microstructure, flow rate, electrical resistivity, pH, and surface roughness is critical for the practical realization of SiC/SiC-based cladding concepts. After a rigorous experimental campaign, this work updates the existing hydrothermal corrosion model to predict hydrothermal corrosion in LWRs. Numerical radiation and coolant chemistry analysis for LWRs conducted based on the updated corrosion kinetic models suggests that CVD SiC is likely a viable environmental barrier coating for Pressurized Water Reactors while questionable for Boiling Water Reactors (BWR) when the effect of irradiation damage on SiC corrosion is considered. An effective mitigation strategy for the double-layer metal coating is proposed for BWR applications. The double-layer metal coating comprising a FeCrAl overcoat with an intermediate Cr bond coating was observed to provide a stable protective barrier against SiC dissolution in BWR conditions. Finally, the proposed metal coating was also fully adherent following quench and burst tests.

36 MATERIALS SCIENCE↗

Kinetic study of treatment of wastewater contains food preservative agent by anaerobic baffled reactor : An overview

The characteristic of wastewater of food industries with preservative substances is high content of organic substances, degradable and high total suspended solid. High organic content in this waste forced the treatment is biologically and pointed out to anaerobic treatment. Anaerobic showed the better performance of degradation than aerobic for high content organic and also for toxic materials. During that day the treatment of food wastewater is aerobically which is high consume of energy required and high volume of sludge produced. The advantage of anaerobic is save high energy, less product of sludge, less requirement of nutrients of microorganism and high efficiency reduction of organic load. The high efficiency of reduction will reduce the load of further treatment, so that, the threshold limit based on the regulation would be easy to achieve. Research of treatment of wastewater of food industries would be utilized by both big scale industries and small industries using addition of preservative substances. The type reactor of anaerobic process is anaerobic baffled reactor that will give better contact between wastewater and microorganism in the sludge. The variables conducted in this research are the baffled configuration, sludge height, preservative agent contents, hydralic retention time and influence of micro nutrients. The respons of this research are the COD effluent, remaining preservative agent, pH, formation of volatile fatty acid and total suspended solid. The result of this research is kinetic model of the anaerobic baffled reactor, reaction kinetic of preservative agent degradation and technology of treatment wastewater contains preservative agent. The benefit of this research is to solve the treatment of wastewater of food industries with preservative substance in order to achieve wastewater limit regulation and also to prevent the environmental deterioration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Qualification of CASMO5 / SIMULATE-3K against the SPERT-III E-core cold start-up experiments

SIMULATE-3K is a three-dimensional kinetic code applicable to LWR Reactivity Initiated Accidents. S3K has been used to calculate several international recognized benchmarks. However, the feedback models in the benchmark exercises are different from the feedback models that SIMULATE-3K uses for LWR reactors. For this reason, it is worth comparing the SIMULATE-3K capabilities for Reactivity Initiated Accidents against kinetic experiments. The Special Power Excursion Reactor Test III was a pressurized-water, nuclear-research facility constructed to analyze the reactor kinetic behavior under initial conditions similar to those of commercial LWRs. The SPERT III E-core resembles a PWR in terms of fuel type, moderator, coolant flow rate, and system pressure. The initial test conditions (power, core flow, system pressure, core inlet temperature) are representative of cold start-up, hot start-up, hot standby, and hot full power. The qualification of S3K against the SPERT III E-core measurements is an ongoing work at Studsvik. In this paper, the results for the 30 cold start-up tests are presented. The results show good agreement with the experiments for the reactivity initiated accident main parameters: peak power, energy release and compensated reactivity. Predicted and measured peak powers differ at most by 13%. Measured and predicted reactivity compensations at the time of the peak power differ less than 0.01 $. Predicted and measured energy release differ at most by 13%. All differences are within the experimental uncertainty. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Multiscale CFD simulation of biomass fast pyrolysis with a machine learning derived intra-particle model and detailed pyrolysis kinetics

Coupling particle and reactor scale models is as essential as reactor fluid dynamics and particle motion for accurate Computational Fluid Dynamic (CFD) simulations of biomass fast pyrolysis reactors due to intraparticle heat transfer and chemical reactions controlling conversion time and product distributions. Direct online coupling of a particle model with a reactor model is computationally expensive, while offline coupling is case-dependent. In this research, solutions from a series of particle pyrolysis simulations were regressed with Artificial Neural Network (ANN). Furthermoer, this machine learning-derived model predicted the same temperature and conversion profiles compared with particle resolved simulation while the isothermal approach overpredicted the temperature by 130 K and underpredicted the conversion time by 30 s. The ANN model was then integrated into CFD simulations of fluidized bed biomass fast pyrolysis with varied feedstocks via coupling PyTorch and MFiX. The averaged error of simulation predicted bio-oil yields with four feedstocks is 6.4%. This multi-scale approach provides an efficient tool for the coupled particle and reactor scale simulations of biomass pyrolysis.

09 BIOMASS FUELS↗

Benchmark specifications and data requirements for initial modeling of the China experimental fast reactor.

A specification is proposed for an initial transient benchmark analysis of the China Experimental Fast Reactor design based on the analysis capabilities of the SAS4A/SASSYS-1 code. For the initial benchmark, a single-channel protected transient overpower accident is defined. Reactivity feedback coefficients will not be required and simplified material properties are recommended. This report also describes the data required for developing the modeling input. This data includes assembly geometry, reactor power distributions, kinetics and decay heat data, and material properties. Comparisons of benchmark results will take place at a future SAS4A/SASSYS-1 training meeting planned to occur at Argonne National Laboratory. Future benchmark specifications will be planned to expand upon this initial model to include more complex reactivity feedback models, material properties, additional assembly geometry, and primary and intermediate coolant systems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Dynamics of Power Pulses in a Research Reactor with Neptunium Nuclear Fuel

The current trend in neutron-aided scientific research presupposes the development of new high-intensity pulsed sources. One variant of such an installation could be a pulsed reactor with a fissile-isotope core – {sup 237}Np. The present work is devoted to a study of the dynamics of power pulses of a neptunium reactor taking account of fast temperature feedback during pulse buildup. The problem is reduced to a simple model of a single frequency oscillator combined with the equation of single point kinetics of a reactor neglecting delayed neutrons. It is shown that on the basis of such an approximation, owing to feedback on the temperature of a fuel element the estimated energy of accidental power pulses decreases by almost a factor of 10 compared with a calculation neglecting fast feedback.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Visualization of Simulation and TAP Interaction

The Temporal Analysis of Products (TAP) Reactor applies transient kinetics to analyze sophisticated chemical reaction mechanisms, rapidly changing temperature, flow rate, pressure or concentration and then monitoring the system’s time dependent response. A simulation tool exists for the TAP reactor, but it requires a visualization platform to interface effectively with researchers. This graphical user interface remedies this problem, fixing many of the difficulties caused by users interacting directly with the simulation code by providing an intuitive web application that satisfies the simulation input parameters for fast generation of data. This tool will ensure robust and repeatable simulation results, expedite the data generating process and enhance the overall ability of TAP to produce significant findings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly sensitive silicon microreactor for catalyst testing

A novel microfabricated chemical reactor for highly sensitive measurements of catalytic activity and surface kinetics is presented. The reactor is fabricated in a silicon chip and is intended for gas-phase reactions at pressures ranging from 0.1 to 5.0 bar. A high sensitivity is obtained by directing the entire gas flow through the catalyst bed to a mass spectrometer, thus ensuring that nearly all reaction products are present in the analyzed gas flow. Although the device can be employed for testing a wide range of catalysts, the primary aim of the design is to allow characterization of model catalysts which can only be obtained in small quantities. Such measurements are of significant fundamental interest but are challenging because of the low surface areas involved. The relationship between the reaction zone gas flow and the pressure in the reaction zone is investigated experimentally. A corresponding theoretical model is presented, and the gas flow through an on-chip flow-limiting capillary is predicted to be in the intermediate regime. The experimental data for the gas flow are found to be in good agreement with the theoretical model. At typical experimental conditions, the total gas flow through the reaction zone is around 3x10{sup 14} molecules s{sup -1}, corresponding to a gas residence time in the reaction zone of about 11 s. To demonstrate the operation of the microreactor, CO oxidation on low-area platinum thin film circles is employed as a test reaction. Using temperature ramping, it is found that platinum catalysts with areas as small as 15 {mu}m{sup 2} are conveniently characterized with the device.

36 MATERIALS SCIENCE↗

Evaluation of Bosch-Based Systems Using Non-Traditional Catalysts at Reduced Temperatures

Oxygen and water resupply make open loop atmosphere revitalization (AR) systems unfavorable for long-term missions beyond low Earth orbit. Crucial to closing the AR loop are carbon dioxide reduction systems with low mass and volume, minimal power requirements, and minimal consumables. For this purpose, NASA is exploring using Bosch-based systems. The Bosch process is favorable over state-of-the-art Sabatier-based processes due to complete loop closure. However, traditional operation of the Bosch required high reaction temperatures, high recycle rates, and significant consumables in the form of catalyst resupply due to carbon fouling. A number of configurations have been proposed for next-generation Bosch systems. First, alternative catalysts (catalysts other than steel wool) can be used in a traditional single-stage Bosch reactor to improve reaction kinetics and increase carbon packing density. Second, the Bosch reactor may be split into separate stages wherein the first reactor stage is dedicated to carbon monoxide and water formation via the reverse water-gas shift reaction and the second reactor stage is dedicated to carbon formation. A series system will enable maximum efficiency of both steps of the Bosch reaction, resulting in optimized operation and maximum carbon formation rate. This paper details the results of testing of both single-stage and two-stage Bosch systems with alternative catalysts at reduced temperatures. These results are compared to a traditional Bosch system operated with a steel wool catalyst.

Abney, Morgan B.↗

Uniformity of GaAs solar cells grown in a kinetically-limited regime by dynamic hydride vapor phase epitaxy

We demonstrate solar cell devices grown on 50 mm diameter GaAs substrates by dynamic hydride vapor phase epitaxy (D-HVPE). In contrast to our prior D-HVPE devices, grown at 650 °C in a transport-limited regime, these devices were grown at 700 °C in a kinetically-limited growth regime in which the growth rate uniformity is controlled by thermally-activated surface reactions. These devices exhibit open-circuit voltages up to 1.07 V, nearly identical performance to the devices grown at lower temperature in a different growth regime. We evaluate the uniformity of device performance and find only a 1% variation in absolute, device efficiency across the majority of the wafer in devices without anti-reflection coating. We analyze the GaAs and GaInP thickness uniformity and GaInP compositional uniformity, using high-tresolution x-ray diffraction mapping, and find that any non-uniformity in device efficiency is not related to variations in these structural parameters. We combine three-dimensional computational fluid dynamics modeling of our reactor with a kinetic model for GaAs growth, and use the combined model to predict spatial GaAs growth rate over a 50 mm wafer area. We compare these predictions with experimental data from our D-HVPE reactor and find excellent agreement. We use the model to the gain insight into the specific mechanisms that control GaAs spatial uniformity in the kinetically-limitedgrowth regime. Furthermore, these results suggest a large parameter window for the growth of high-performance optoelectronic devices by D-HVPE, possibly with large area uniformity.

14 SOLAR ENERGY↗

Thermodynamic and kinetic modeling of Mn-Ni-Si precipitates in low-Cu reactor pressure vessel steels

Formation of large volume fractions of Mn-Ni-Si precipitates (MNSPs) causes excess irradiation embrittlement of reactor pressure vessel (RPV) steels at high, extended-life fluences. Thus, a new and unique, semi-empirical cluster dynamics model was developed to study the evolution of MNSPs in low-Cu RPV steels. The model is based on CALPHAD thermodynamics and radiation enhanced diffusion kinetics. The thermodynamics dictates the compositional and temperature dependence of the free energy reductions that drive precipitation. The model treats both homogeneous and heterogeneous nucleation, where the latter occurs on cascade damage, like dislocation loops. The model has only four adjustable parameters that were fit to an atom probe tomography (APT) database. The model predictions are in semi-quantitative agreement with systematic Mn, Ni and Si composition variations in alloys characterized by APT, including a sensitivity to local tip-to-tip variations even in the same steel. The model predicts that heterogeneous nucleation plays a critical role in MNSP formation in lower alloy Ni contents. Single variable assessments of compositional effects show that Ni plays a dominant role, while even small variations in irradiation temperature can have a large effect on the MNSP evolution. Within typical RPV steel ranges, Mn and Si have smaller effects. Furthermore, the delayed but then rapid growth of MNSPs to large volume fractions at high fluence is well predicted by the model. For purposes of illustration, the effect of MNSPs on transition temperature shifts are presented based on well-established microstructure-property and property-property models.

36 MATERIALS SCIENCE↗

Coupling of kinetic Monte Carlo simulations of surface reactions to transport in a fluid for heterogeneous catalytic reactor modeling

We have developed a method to couple kinetic Monte Carlo simulations of surface reactions at a molecular scale to transport equations at a macroscopic scale. This method is applicable to steady state reactors. We use a finite difference upwinding scheme and a gap-tooth scheme to efficiently use a limited amount of kinetic Monte Carlo simulations. In general the stochastic kinetic Monte Carlo results do not obey mass conservation so that unphysical accumulation of mass could occur in the reactor. We have developed a method to perform mass balance corrections that is based on a stoichiometry matrix and a least-squares problem that is reduced to a non-singular set of linear equations that is applicable to any surface catalyzed reaction. The implementation of these methods is validated by comparing numerical results of a reactor simulation with a unimolecular reaction to an analytical solution. Furthermore, the method is applied to two reaction mechanisms. The first is the ZGB model for CO oxidation in which inevitable poisoning of the catalyst limits the performance of the reactor. The second is a model for the oxidation of NO on a Pt(111) surface, which becomes active due to lateral interaction at high coverages of oxygen. This reaction model is based on ab initio density functional theory calculations from literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical looping conversion of CH4/CO2 to syngas on 5wt.%Ni@Ce0.6Zr0.4O2 catalyst: Impact of dynamic accumulation of surface carbon and oxygen vacancies

Syngas, a combination of carbon monoxide (CO) and hydrogen (H2), is a precursor to many chemicals and fuels, contributing to the billion-dollar global hydrocarbon industry. Chemical looping reforming (CLR) of the greenhouse gases methane (CH4) and carbon dioxide (CO2) allows for energy-efficient production of syngas. 5wt.% nickel (Ni) on ceria-zirconia (5wt%Ni@Ce0.6Zr0.4O2) mixed metal oxide catalyst was investigated here to explore pathways for enhanced syngas production on sustainable earth-abundant transition metal supported catalysts. The role of reduction-oxidation (redox) state of the catalyst, and carbon formation on the catalyst surface during chemical looping is explored to drive superior reaction kinetics, conversions, selectivity, and syngas ratios (H2/CO). The bulk and surface structure of the catalyst, along with carbon deposition features were characterized by electron microscopy, X-Ray diffraction, and ex situ Raman spectroscopy. The dynamic evolution of catalysts under CLR reaction conditions and the intrinsic reaction mechanisms were probed with in situ Raman spectroscopy, in situ Fourier transform spectroscopy, dynamic oxygen storage capacity (DOSC), and the Temporal Analysis of Products (TAP) reactor studies. Intrinsic kinetics of syngas production via CLR was correlated to the redox state of catalyst and the participation of nickel-catalyzed multiwalled carbon nanotube (CNT) growth, allowing enhanced CLR reaction performance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Interpretation of energy deposition data from historical operation of the transient test facility (TREAT)

The Transient Test Reactor (TREAT) at Idaho National Laboratory will resume operations in late 2017 after a 23 year hiatus while maintained in a cold standby state. Over that time period, computational power and simulation capabilities have increased substantially and now allow for new multiphysics modeling possibilities that were not practical or feasible for most of TREAT's operational history. Hence the return of TREAT to operational service provides a unique opportunity to apply state-of-the-art software and associated methods in the modeling and simulation of general three-dimensional steady state and kinetic behavior for reactor operation, and for coupling of the core power transient model to experiment simulations. However, measurements taken in previous operations were intended to predict power deposition in experimental samples, with little consideration of three-dimensional core power distributions. Hence, interpretation of data for the purpose of validation of modern methods can be challenging. For the research discussed herein, efforts are described for the process of proper interpretation of data from the most recent calibration experiments performed in the core, the M8 calibration series (M8-CAL). These measurements were taken between 1990 and 1993 using a set of fission wires and test fuel pins to estimate the power deposition that would be produced in fast reactor test fuel pins during the M8 experiment series. Because of the decision to place TREAT into a standby state in 1994, the M8 series of transients were never performed. However, potentially valuable information relevant for validation is available in the M8-CAL measurement data, if properly interpreted. This article describes the current state of the process of recovery of useful data from M8-CAL measurements and quantification of biases and uncertainties to potentially apply to the validation of multiphysics methods.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of a plant-wide dynamic model of an integrated gasification combined cycle (IGCC) plant

In this presentation, development of a plant-wide dynamic model of an advanced Integrated Gasification Combined Cycle (IGCC) plant with CO2 capture will be discussed. The IGCC reference plant generates 640 MWe of net power using Illinois No.6 coal as the feed. The plant includes an entrained, downflow, General Electric Energy (GEE) gasifier with a radiant syngas cooler (RSC), a two-stage water gas shift (WGS) conversion process, and two advanced 'F' class combustion turbines partially integrated with an elevated-pressure air separation unit (ASU). A subcritical steam cycle is considered for heat recovery steam generation. Syngas is selectively cleaned by a SELEXOL acid gas removal (AGR) process. Sulfur is recovered using a two-train Claus unit with tail gas recycle to the AGR. A multistage intercooled compressor is used for compressing CO2 to the pressure required for sequestration. Using Illinois No.6 coal, the reference plant generates 640 MWe of net power. The plant-wide steady-state and dynamic IGCC simulations have been generated using the Aspen Plus{reg_sign} and Aspen Plus Dynamics{reg_sign} process simulators, respectively. The model is generated based on the Case 2 IGCC configuration detailed in the study available in the NETL website1. The GEE gasifier is represented with a restricted equilibrium reactor model where the temperature approach to equilibrium for individual reactions can be modified based on the experimental data. In this radiant-only configuration, the syngas from the Radiant Syngas Cooler (RSC) is quenched in a scrubber. The blackwater from the scrubber bottom is further cleaned in the blackwater treatment plant. The cleaned water is returned back to the scrubber and also used for slurry preparation. The acid gas from the sour water stripper (SWS) is sent to the Claus plant. The syngas from the scrubber passes through a sour shift process. The WGS reactors are modeled as adiabatic plug flow reactors with rigorous kinetics based on the mid-life activity of the shift-catalyst. The SELEXOL unit consists of the H2S and CO2 absorbers that are designed to meet the stringent environmental limits and requirements of other associated units. The model also considers the stripper for recovering H2S that is sent as a feed to a split-flow Claus unit. The tail gas from the Claus unit is recycled to the SELEXOL unit. The cleaned syngas is sent to the GE 7FB gas turbine. This turbine is modeled as per published data in the literature. Diluent N2 is used from the elevated-pressure ASU for reducing the NOx formation. The heat recovery steam generator (HRSG) is modeled by considering generation of high-pressure, intermediate-pressure, and low-pressure steam. All of the vessels, reactors, heat exchangers, and the columns have been sized. The basic IGCC process control structure has been synthesized by standard guidelines and existing practices. The steady-state simulation is solved in sequential-modular mode in Aspen Plus{reg_sign} and consists of more than 300 unit operations, 33 design specs, and 16 calculator blocks. The equation-oriented dynamic simulation consists of more than 100,000 equations solved using a multi-step Gear's integrator in Aspen Plus Dynamics{reg_sign}. The challenges faced in solving the dynamic model and key transient results from this dynamic model will also be discussed.

97 MATHEMATICS AND COMPUTING↗

Gasificaton Transport: A Multiphase CFD Approach & Measurements

The objective of this project was to develop predictive theories for the dispersion and mass transfer coefficients and to measure them in the turbulent fluidization regime, using existing facilities. A second objective was to use our multiphase CFD tools to suggest optimized gasifier designs consistent with aims of Future Gen. We have shown that the kinetic theory based CFD codes correctly compute: (1) Dispersion coefficients; and (2) Mass transfer coefficients. Hence, the kinetic theory based CFD codes can be used for fluidized bed reactor design without any such inputs. We have also suggested a new energy efficient method of gasifying coal and producing electricity using a molten carbonate fuel cell. The principal product of this new scheme is carbon dioxide which can be converted into useful products such as marble, as is done very slowly in nature. We believe this scheme is a lot better than the canceled FutureGen, since the carbon dioxide is safely sequestered.

01 COAL, LIGNITE, AND PEAT↗