Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced fracture model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

268 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigating Material Properties of Subsurface Rock Formations Modified by Engineering Mineral Precipitation (Final Scientific and Technical Report)

Montana State University’s (MSU) Energy Research Institute (ERI), in collaboration with the Center for Biofilm Engineering (CBE) and the Department of Civil Engineering (CE), has conducted a long‐term research program aimed at developing a novel cementing agent to address wellbore integrity and reduce the unwanted upward migration of fluids and greenhouse gases from the subsurface. The primary technology developed through this research program is known as ureolysis‐induced calcite precipitation (UICP), which harnesses bio‐chemical processes to precipitate calcium carbonate (CaCO 3 ). The same general process can also be called microbially-induced calcium carbonate precipitation (MICP) when microbes provide the process-catalyzing urease enzyme. Both terms are used in this report. Results have conclusively demonstrated that, if properly controlled, UICP can successfully seal fractures, high permeability zones, and compromised cement in the vicinity of wellbores and in nearby caprock. This technology has been successfully deployed to mitigate annular leakage in two test wells and over sixty commercial wells with a 100% success rate. This success in downhole deployment generates consideration of other subsurface applications where UICP could provide benefit to the energy sector, such as shale property modification for unconventional oil and gas recovery. The focus of this research project was to investigate fundamental material and mechanical properties of select shale cores and analyze how these properties change due to engineered mineral precipitation with the intent to control these properties to achieve a range of engineering objectives. Ultimately, the project aim was to identify valuable new areas where application of UICP might contribute to national energy security and environmental protection. The research workplan coupled UICP treatment of core samples, nuclear magnetic resonance (NMR) characterization, and mechanical strength testing at MSU with advanced X‐Ray micro-computed tomography (μCT) imaging and numerical modeling performed by collaborators at two national laboratories, the National Energy Technology Laboratory (NETL) and Lawrence Berkeley National Laboratory (LBNL). Experimental results are useful to inform geo-mechanical models which could be applied to predict mineralized rock formation behavior at field scale. Our findings suggest that NMR and μCT methods to detect and quantify biomineral formation in shale fractures are complementary and consistent with each other. Either could be used to estimate the volume of new mineral formed by UICP in shale fractures. The use of surfactants and guar gum to enhance biomineral precipitation in shale fractures merits further research. UICP can, under some conditions, increase the tensile strength of sealed shale fractures beyond that of the intact shale. These findings demonstrate that continued research in this area may be valuable to understanding and improving shale resource recovery techniques.

58 GEOSCIENCES↗
DOE OSTI2024

Leveraging a Neural Network-Enhanced Reproducing Kernel Particle Method for Multiphysics Degradation Modeling of Energy Storage Materials

Energy storage materials exhibit strong electro-chemo-mechanical coupling and highly anisotropic material properties, contributing to the formation and propagation of micro-cracking during charge/discharge cycling and resulting in reduced performance and service life. A coupled electro-chemo-mechanical reproducing kernel particle method (RKPM) formulation has been developed to analyze this system. With microstructural images supplied by the National Renewable Energy Laboratory (NREL), pixel-based model construction by RKPM is used to represent the complex material microstructures that dictate the coupled physics of these systems. Traditional electro-chemo-mechanical models rely on mesh-based finite element methods, which can lead to difficulties in meshing such complex geometries and capturing crack propagation due to mesh dependency. Here, a neural network-enhanced reproducing kernel particle method (NN-RKPM) [1, 2] is introduced to effectively model damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. NN-RKPM is additionally used to inform how crack opening and closure in turn affect the coupled chemical equations and material microstructure. Reference: [1] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, pp 4422-4454, https://doi.org/10.1002/nme.7040, 2022. [2] Baek, J., Chen, J. S., "A Neural Network-Based Enrichment of Reproducing Kernel Approximation for Modeling Brittle Fracture", Computer Methods in Applied Mechanics and Engineering Vol. 410, 116590, 2024.

degradation↗
DOE OSTI2026

RU Net for Automatic Characterization of TRISO Fuel Cross Sections

TRistructural ISOtropic (TRISO) particle fuel is a type of nuclear fuel known for its high-temperature and high-burnup performance. Each sub-millimeter diameter TRISO particle consists of uranium-oxycarbide (UCO) or UO2 fuel kernel, coated with buffer, inner pyrolytic carbon (IPyC), silicon carbide (SiC), and outer pyrolytic carbon (OPyC) layers. The SiC layer acts as the main containment barrier for the TRISO particle to retain the fission products, while the IPyC and OPyC layers provide additional barriers to the release of fission products, especially fission gases. During irradiation, phenomena like kernel swelling, buffer densification, and IPyC fracture may impact fuel performance. Post-irradiation microscopy on entire compact cross sections or samples of individual particles deconsolidated from compacts is often used to identify these irradiation-induced changes in morphology. However, each fuel compact generally contains thousands of TRISO particles. To get statistical information on these phenomena, it is cumbersome work if done manually. For example, to get information about swelling/densification behaviors of different layers or kernels after irradiation, researchers previously manually measured the perimeter of each TRISO layer in hundreds of particles after four rounds of iterative grinding and polishing encompassing more than 2000 cross-section images for a total of four fuel compacts. To attempt to reduce the subjectivity inherent in that process and accelerate data analysis, we conducted a study on the automatic TRISO layer segmentation on cross-sectional microscopic images using Convolutional Neural Networks (CNNs). CNNs are a class of machine learning algorithms specifically designed for processing structured grid data that have gained popularity in recent years due to their remarkable performance in various computer vision tasks, including image classification, object detection, and image segmentation. In this research, we have generated the large irradiated TRISO layer dataset with more than 2000 cross-section TRISO microscopic images and the corresponding annotated images. Based on these annotated images, we have employed different CNNs for automatic segmentation of different TRISO layers. These include RU-Net (developed in this study), as well as three existing architectures: U-Net, Residual Network (ResNet), and Attention U-Net. The preliminary results show that the model based on RU-Net has the best performance in terms of intersection-over-union (IoU). Through the aid of these CNN models, we can expedite the analysis of TRISO particle cross-sections, significantly reducing the manual labor involved and improving the objectivity of the segmentation results.

Convolutional Neural Networks↗
DOE OSTI2025

Stress accommodation in nanoscale dolan bridges designed for superconducting qubits

Josephson junctions are the principal circuit element in numerous superconducting quantum information devices and can be readily integrated into large-scale electronics. However, device integration at the wafer scale necessarily depends on having a reliable, high-fidelity, and high-yield fabrication method for creating Josephson junctions. When creating Al/AlO x based superconducting qubits, the standard Josephson junction fabrication method relies on a sub-micron suspended resist bridge, known as a Dolan bridge, which tends to be particularly fragile and can often times fracture during the resist development process, ultimately resulting in device failure. In this work, we demonstrate a unique Josephson junction lithography mask design that incorporates stress-relief channels. Our simulation results show that the addition of stress-relief channels reduces the lateral stress in the Dolan bridge by more than 70% for all the bridge geometries investigated. In practice, our novel mask design significantly increased the survivability of the bridge during device processing, resulting in 100% yield for over 100 Josephson junctions fabricated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Evaluation of ceria as a surrogate material for UO 2 in experiments on fuel cracking driven by resistive heating

A variety of normal operation and accident scenarios can generate thermal stresses large enough to cause cracking in light-water reactor (LWR) fuel pellets. Cracking of fuel pellets can lead to reduced heat removal, larger centerline temperatures, and localized stress in cladding all of which impact fuel performance. Furthermore, pellet cracking also contributes to a temperature reduction in the pellet since the pellet fragments tend to move towards the heat sink (cladding), and the heat flow remains predominantly radial despite the presence of cracks. It is important to understand the temperature profile on the pellet before and after cracking to improve cracking models in fuel performance codes However, in-reactor observation and measurement of cracking is very challenging owing to the harsh environment and design of fuel rods. Recently, an experimental pellet cracking test stand was developed for separate effects testing of normal operations and accident temperature conditions, using thermal imaging to capture the pellet surface temperature for evaluation of thermal stresses and optical imaging to capture the evolution of cracking in real time. Cracking experiments were initially performed using ceria (CeO 2 ) as a surrogate fuel material, which is useful for developing and demonstrating the experimental approaches but is also valuable in its own right for cracking model development and validation. A combination of induction and resistance heating was used for volumetric heat generation in the pellet creating a thermal gradient. The material properties of CeO 2 and UO 2 are reviewed and compared for use in model development. Simulations of the experiment were performed to evaluate the behavior of the surrogate (CeO 2 ) fuel in BISON. The measured temperature profiles from BISON models match reasonably well with the observed experiments for the ceria pellets before cracking. The findings from this work will help improve confidence in fracture models used for fuel pellets under similar in-reactor conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Preliminary Study of Potential Utilization of Triassic Rift Basins for Long-Term Carbon Sequestration

Triassic rift basins of the eastern United States present a potential option for long–term carbon dioxide (CO 2 ) sequestration. Exposed and buried basins are located near large point CO 2 sources. Because of their similar origins, comparable fill successions indicate a level of reproducibility that can be conveyed between basins. The thick rock successions of the exposed Culpeper and Gettysburg basins served as proxies for understanding of the basin sequences. Their study allowed recognition of five mappable assemblages of rock types, herein termed lithofacies associations. These lithofacies associations were formed by alluvial fan, braided and meandering streams and marginal and distal lake depositional processes.Stratigraphic architecture of the lithofacies associations within exposed basins suggests a vertical succession that consists of an initial coarse-grained fluvial succession that is progressively replaced upward and basinward by finer grained lacustrine deposits. Along the faulted margins of the basins alluvial fans transitioning to fluvial delta deposits reflect lateral progradation and contemporaneous lateral components of the basin filling.To test the model devised in exposed basins, facies associations were developed for the buried Taylorsville Basin. This basin preserves over 8,000 feet of Triassic rocks that are concealed beneath more than 2,000 feet of Cretaceous and Tertiary Coastal Plain sediments. Composition and stratigraphic architecture of these rocks are similar to those observed in exposed basins. Infilling of the basin was the result of vertical aggradation and lateral progradation of coarse-grained to fine-grained facies. Based upon study of outcrops in the Culpeper and Gettysburg basins, groups of recurring lithologic facies were identified as the fundamental constructs of the basin’s sediment infilling. These groups of facies, termed lithofacies associations, represent an amalgamation of lithologic components from broadly similar depositional systems. These lithologic associations were then extrapolated into the exposed and buried portions of the Taylorsville basins. This effort determined that Triassic rift basins provide several avenues for potential study of geologic sequestration of carbon. The characteristic rift basin succession in the basins presents possible reservoir targets within the marginal fluvial deposits. Furthermore, intrusive and extrusive mafic bodies present a potential source of fracture porosity that could serve as CO 2 reservoirs. Porosity values from thin section analysis of exposed basin samples are higher in alluvial fan and braided fluvial lithofacies. Porosity is highest in samples that show less compaction, due to a lack of ductile lithic fragments and/or higher stratigraphic position. Log data from the Taylorsville Basin indicates that porosity and permeability values in basin marginal fluvial strata are elevated. Near the center of the basin, porosity and permeability values are greatly reduced, primarily owing to the fine-grained character of the lacustrine deposits. Some Triassic basins also contain thick intervals of concordant extrusive and intrusive mafic igneous rocks. These igneous bodies are potential CO 2 reservoirs for several reasons. Firstly, extrusive lava flows provide potential storage in the layers of primary porosity that occur in the vesicules formed at the top of lava flows. Secondly, both lava flows and subsurface igneous sills exhibit extensive fracture porosity produced by the rapid cooling of the flows and intrusions. Thirdly, these igneous rocks are mafic in composition, and studies have shown that iron- and magnesium-rich mafic rocks provide sequestration opportunities through carbonate remineralization. Lastly, extrusive and intrusive igneous rocks are invariably preserved within fine-grained lake deposits. These lacustrine sediments can serve as a fine-grained confining layer that encases the igneous rocks both above and below.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Deep Learning–Assisted Multiobjective Optimization of Geological CO 2 Storage Performance under Geomechanical Risks

In geological CO 2 storage, designing the optimal well control strategy for CO 2 injection to maximize CO 2 storage while minimizing the associated geomechanical risks is not trivial. This challenge arises due to pressure buildup, CO 2 plume migration, the highly nonlinear nature of geomechanical responses to rock-fluid interaction, and the high computational cost associated with coupled flow and geomechanics simulations. In this paper, we introduce a novel optimization framework to address these challenges. The optimization problem is formulated as follows: maximize total CO 2 storage while minimizing geomechanical risks by adjusting the injection schedules within bounded constraints. The geomechanical risks are primarily driven by injection-induced pressure build-up, which is characterized by ground displacement and the induced microseismicity. We used the Fourier neural operator (FNO)-based deep learning model to construct surrogate models, replacing the time-consuming coupled flow and geomechanics simulations for evaluating the aforementioned objective functions. The developed surrogate models have been incorporated into a multiobjective optimization framework through a genetic algorithm to reduce the computational burden. The proposed optimization framework reduces the computational cost from approximately 2,400 hours, when using objective function evaluations based on physics-based simulations, to around 20 minutes. A set of Pareto-optimal solutions of the proposed workflow yields nontrivial optimal decisions, reducing the microseismicity potential and the vertical displacement. This Pareto front highlights the optimal trade-offs between CO 2 storage amount, safety, and ground displacement, emphasizing the need for careful optimization and management of injection strategies to achieve a balanced outcome. The novelty of this work is twofold. First, we demonstrate the importance of incorporating the minimization of the geomechanical risks as objective functions into the CO 2 storage optimization workflow to mitigate the potential risk of induced microseismicity and ground displacement. Second, we leverage the FNO-based surrogate models to optimize a real-field CO 2 storage operation.

42 ENGINEERING↗
DOE OSTI2022

Development Of Thermodynamic and Kinetic Simulation Tools and Testing Procedures for Enhanced Durability of Concrete Containing Industrial By-Products

This project developed screening tools that enable evaluation of alternative cementitious binders that create concretes to significantly reduce energy and emissions while remaining cost competitive on both initial and long-term costs. The team began with the viewpoint that acceptance of new cementitious binder products has a substantially greater chance of successful implementation when capital investment is not excessive and the end product has customers that have experience and resources to use this. As such, a binder system that is based on portland cement with blended using industrial by-products (alternative cementitious materials) has the potential for dramatic and meaningful impact. The team has focused on developing implementable solutions in specifications and current practice. This however requires three main factors: 1) ability to screen byproducts and alternative materials for success, 2) ability to ‘treat’ materials chemically to enhance kinetics, and 3) ability to provide predictions of performance of both binders and concrete from first principles. The project developed/refined a state of the art and scientifically based screening test for SCM called the pozzolanic reactivity test. The team developed kinetic models to simulate these materials as well as experimental approaches to alter selected reactions. Simulation tools were developed that enable the performance of concrete to be predicted based on the chemistry and reactivity of the cement and alternative SCM. Specifically, this project: • enhanced the kinetic reactivity models for use in multi-scale computational programs that use thermodynamics to predict reaction products. 2 • developed scaling models to extend thermodynamic modeling to link these models with pore structure. This enables strength, transport property, and coupled transport prediction. • developed tools to predict performance of cementitious materials using the pozzolanic reactivity test and chemical composition. The predicted properties are consistent with AASHTO R101 and the CEB-FIP model code and can be measured using associated test procedures. • demonstrated mechanical and fracture based modeling tools that thermodynamic predictions and inputs to predict concrete service life. These results have been used to demonstrate the value of enabling specifications to include ASTM C 595 cement as well ASTM C150 cement. In addition, these products are being used to expedite the evaluation of alternative SCM to aide in determining which materials have potential value and what ‘compositions’ of blended cements merit further investment.

42 ENGINEERING↗
NASA NTRSDate not supplied

Overview of Additively Manufactured TPS Proposed Flight Test and Earth Re-Entry Capsule Design

A flight mechanics overview is presented of an Earth flight test designed to investigate a novel, 3D printed thermal protection system (TPS) that is currently in development at NASA as part of the Additive Manufacturing of Thermal Protection Systems project. The project is pioneering a method to print a thermal protection system onto an entry vehicle forebody one layer at a time. This method reduces labor and complexity as compared to traditional manufacturing methods while increasing mission-dependent customization of through-depth materials properties. The flight test has three objectives. First, subject the forebody stagnation point of a capsule equipped with additively manufactured TPS (AMTPS) material to peak heat fluxes in excess of 100 $W/cm^2$. Second, capture in-flight data to enable flight reconstruction and AMTPS material thermal response model improvement. Third, recover the capsule with data storage and forebody AMTPS intact to enable post-flight inspection and analysis of AMTPS performance. The flight test trajectory is designed to achieve a peak stagnation point, cold-wall, entry heat flux of 135~$W/cm^2$. Flight mechanics simulations are performed using the Program to Optimize Simulated Trajectories II (POST2) and Monte-Carlo analysis yields statistical percentiles on vehicle performance at key points along the trajectory. Based on the flight mechanics analysis presented in this paper, a prototype capsule was designed, partially fabricated, and underwent preliminary component stress testing in preparation for fabrication of the flight unit capsule. The capsule outer mold line is a modified version of the heritage Mars Microprobe geometry. The capsule has a 0.356~m diameter, a 30~kg mass, and a hypersonic ballistic coefficient of 300~$kg/m^2$. Sensor selection is guided by flight dynamics simulations with the goal of resolving the re-entry heating pulse. On-board instrumentation include forebody and aftbody pressure sensors and thermocouples, a 9-axis IMU, a GPS receiver, and an Iridium satellite modem, all of which collect and store data throughout flight via on-board avionics systems. A two-stage parachute system is designed to decelerate the capsule to touchdown velocities that will not result in significant fracture or deformation of the charred AMTPS material at ground impact.

Flight Mechanics↗
DOE OSTI2023

Stability study of aqueous foams under high-temperature and high-pressure conditions relevant to Enhanced Geothermal Systems (EGS)

In Enhanced Geothermal System (EGS) hydraulic fracturing is carried out by injecting cold water into deep Hot Dry Rocks (HDR) under carefully controlled conditions to create new or reopen existing fractures. Water-based fracturing fluids demonstrate some challenges including immense quantity of water usage, water sensitivity of the formations, water blocking, and lack of proppant carrying capacity and transportation. Thus, an alternative is to use foam-based fracturing fluid which offers potential advantage over conventional water-based fracturing fluid such as minimum water usage, reduced wellbore damage, high proppant carrying capacity, and less environmental damage. However, foams are complex mixture of gaseous phase and liquid phase which are thermodynamically unstable at downhole conditions, and their stability can decrease over time due to liquid drainage, bubble coarsening, and coalescence. This paper shows laboratory experiments executed to study foam stability at high temperature (200°C) and high pressure (6.9MPa) conditions which simulates the geothermal environment. Foam stability was characterized by half-life of foam, which is defined as the time taken by the foam to decreases by 50% of its original height due to drainage. In this paper, two types of gaseous phases, nitrogen (N 2 ) and carbon dioxide (CO 2 ) were investigated. Also, based on successful practice of foam-based fracturing fluid in oil and gas industries, four surfactants, including Alpha olefin sulfonate (AOS), Sodium dodecyl sulfonate (SDS), Tergitol™ (NP – 40), and Cetyltrimethylammonium chloride (CTAC) at optimum concentration of 1wt.% were tested for best stability performance. In addition, different stabilizing agents including guar gum, bentonite clay, crosslinker, silicon dioxide nanoparticles (SiO 2 ), graphene oxide (GO) were also studied. Experimental results showed that N 2 foams were more stable than CO 2 foams. It was observed that foam half-life decreased with the increase in temperature. Among all the surfactants, AOS foams showed the most promising thermal stability at high temperatures. Moreover, with the addition of stabilizing agents, foam's half-life was enhanced. Stabilizing agents such as crosslinker and GO dispersion showed the most stable foams with half-life recorded at 20min and 17min, respectively, at 200°C and 6.9MPa. Finally, pressure also showed a positive effect on foam stability; with increased pressure, foam half-life was increased. Based on the experimental data, analytical models for the effect of temperature and pressure were developed, considering foam degradation is a first-order kinetic reaction that linearly depends on the foam drainage mechanism. The effect of temperature on foam half-life was studied as an exponential decay model. In this model, foam half-life is a function of drainage rate constant (D A ) and activation energy (E a ) of the foam system. The effect of pressure on foam half-life was found to obey a power-law model where an increase in pressure showed an increase in foam half-life. Furthermore, a linear relation was studied for the effect of pressure on foam activation energy and drainage rate. Then the combined effects of temperature and pressure were studied, which yielded an analytical model to predict the foam stabilities in terms of half-life for different foam compositions. In conclusion, this research indicates that with an appropriate selection of surfactants and stabilizing agents, it is possible to obtain stable foams, which could replace conventional water fracturing fluid under EGS conditions.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

Irradiation damage concurrent challenges with RAFM and ODS steels for fusion reactor first-wall/blanket: a review

Reduced activation ferritic martensitic (RAFM) and oxide dispersion strengthened (ODS) steels are the most promising candidates for fusion first-wall/blanket (FW/B) structures. The performance of these steels will deteriorate during service due to neutron damage and transmutation-induced gases, such as helium/hydrogen, at elevated operating temperatures. Here, after highlighting the operating conditions of fusion reactor concepts and a brief overview, the main irradiation-induced degradation challenges associated with RAFM/ODS steels are discussed. Their long-term degradation scenarios such as (a) low-temperature hardening embrittlement (LTHE)—including dose-temperature dependent yield stress, tensile elongations, necking ductility, test temperature effect on hardening, Charpy impact ductile-to-brittle transition temperature and fracture toughness, (b) intermediate temperature cavity swelling, (c) the effect of helium on LTHE and cavity swelling, (d) irradiation creep and (e) tritium management issues are reviewed. The potential causes of LTHE are discussed, which highlights the need for advanced characterisation techniques. The mechanical properties, including the tensile/Charpy impact of RAFM and ODS steels, are compared to show that the current generation of ODS steels also suffers from LTHE, and shows irradiation hardening up to high temperatures of ~400 °C–500 °C. To minimise this, future ODS steel development for FW/B-specific application should target materials with a lower Cr concentration (to minimise α'), and minimise other elements that could form embrittling phases under irradiation. RAFM steel-designing activities targeting improvements in creep and LTHE are reviewed. The need to better understand the synergistic effects of helium on the thermo-mechanical properties in the entire temperature range of FW/B is highlighted. Because fusion operating conditions will be complex, including stresses due to the magnetic field, primary loads like coolant pressure, secondary loads from thermal gradients, and due to spatial variation in damage levels and gas production rates, an experimentally validated multiscale modelling approach is suggested as a pathway to future reactor component designing such as for the fusion neutron science facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Foam Fracturing Study for Stimulation Development of Enhanced Geothermal Systems

The large thermal gradients and high subsurface temperatures of the western region of the U.S. hold great potential for the implementation of enhanced geothermal systems (EGS). The development of these potential EGS resources requires stimulation of the reservoir to enhance permeability and it has been widely reported that a substantial amount of water will be required should conventional hydraulic stimulation be used. This presents a huge challenge and a high risk to the geothermal development because the water stress1 in these areas is already high or extremely high. The use of foam, a gas/liquid mixture predominantly composed of gas, in fracturing is considered and explored in this project as a potential approach to address water concerns with hydraulic stimulation in the development of EGS. This project, led by Oak Ridge National Laboratory (ORNL) in collaboration with Temple University, was awarded in an open lab call in 2018, and was part of the DOE GTO waterless stimulation initiative. The goal of the project was to demonstrate the feasibility of foam fracturing for EGS development through two primary tasks: Task 1: Laboratory study of the effectiveness of foam fracturing for representative geological materials, including cyclic pressurization using foam (led by ORNL) and Task 2: High temperature foam material selection and characterization (led by Temple University). In FY19, ORNL finished the critical review on serval issues associated with foam fracturing and the implementation of the proposed tasks in a lab study (Wang, et al., 2019), and completed the foam fracturing testing using cement as a model material (Wang, et al, 2020a). The work at ORNL was geared up to develop a brand-new foam testing system in FY20. The purchase of main components for the new system was finished in the first half of the FY20. The assembly of the foam testing system and foam fracturing testing were completed in the second half of the FY20 (Wang, et al., 2021a). Task 1 required the development of a test system which can be used to perform hydraulic fracturing of geological specimens with both water and foamed liquids at pressure up to 6,000 psi (41.4 MPa). The system possesses several capabilities that conventional injection systems lack for hydraulic fracturing. In addition to its ability to generate foam with controlled quality, it is capable of cycling pressure levels between specified values up to frequencies of 50 Hz. The latter capability was developed to evaluate the hypothesis that cyclic loading of samples would produce enhanced fracturing. The system consists of two sections: one for foam generation and another for foam injection. The foam is generated through separate control and pressurization of liquid and gas phases with controlled flow rates. The injection section is equipped with a low-flow Coriolis flow that monitors the density of foam to ensure the injection is in the range of target foam quality2. Experimental results of foam fracturing are reported for cylindrical granite specimens using water and aqueous N2 foam as the fracturing fluids. All experiments were performed for unconfined conditions. The effects of injection mode (i.e., monotonic vs cyclic pressurization) on breakdown pressure and failure response sample were investigated using water alone as a fracturing fluid and foams with a range of compositions. It was found that in the case of monotonic injection, the breakdown pressure of granite specimens tended to be slightly higher when fracturing with foam. Additionally, with a foam quality of 90%, the water use can be reduced by 50 to 84%, depending on hole size. On the other hand, it was observed that the breakdown pressure can be brought down to 70% of the monotonic breakdown pressure by using low cycle fatigue. Finally, discussions are presented regarding injectivity and water use reduction.

15 GEOTHERMAL ENERGY↗
NASA NTRS2024

Advances in Thermoplastic Composites Over Three Decades – A Literature Review

Recently, there has been a renewed interest in thermoplastic composites driven mainly by advances in automation which can lead to significant cost reductions by increasing manufacturing rates while simultaneously reducing the part count and energy consumption relative to the manufacturing of thermoset composites. At the same time, new material systems have been developed and the thermoplastic composites prepreg material quality has improved over time. Additionally, thermoplastic composites have nearly infinite room-temperature shelf life and production scraps can be reused and retired parts can be recycled, providing opportunities for more sustainable operations and downstream markets. These factors have contributed to a strong interest in advancing thermoplastic composites for aerospace, automotive, and other industrial applications. The objective of the present study is to assess the state of the art regarding the maturity and performance of thermoplastic composite materials and to document the advances made in manufacturing and assembly of thermoplastic composite structures. Therefore, more than 200 NASA reports, conference proceedings and journal papers spanning three and a half decades (1986-2022) were reviewed and the findings summarized. The current study, however, is limited in scope with a focus on the application of thermoplastic composites to aircraft structures. Further, the study does not provide a comprehensive assessment of the available literature but rather offers an overview of past and present research being conducted in the field of thermoplastic composites. The information provided may be used to identify gaps and help guide future research and development. In this report, the opportunities offered by the use of thermoplastic composites in general and challenges encountered in particular are presented first. Second, an overview of thermoplastic materials is presented, manufacturing methods are discussed, and new methods for fastener-less assembly such as welding are introduced. Third, tests that have been performed on different levels of the building block, ranging from coupon to structural level, are presented. In particular, fracture toughness results for different thermoplastic composite materials are used to demonstrate their performance compared to state-of-the-art thermoset composites. Fourth, several examples of analyses are discussed including process modelling and progressive damage analysis (PDA). An extensive list of references and appendices with tables support the narrative. Lastly, a brief summary with outlook and recommendations for future research is provided.

composites↗
DOE OSTI2025

Learning the factors controlling mineral dissolution in three-dimensional fracture networks: applications in geologic carbon sequestration

We perform a set of high-fidelity simulations of geochemical reactions within three-dimensional discrete fracture networks (DFN) and use various machine learning techniques to determine the primary factors controlling mineral dissolution. The DFN are partially filled with quartz that gradually dissolves until quasi-steady state conditions are reached. At this point, we measure the quartz remaining in each fracture within the domain as our primary quantity of interest. We observe that a primary sub-network of fractures exists, where the quartz has been fully dissolved out. This reduction in resistance to flow leads to increased flow channelization and reduced solute travel times. However, depending on the DFN topology and the rate of dissolution, we observe substantial variability in the volume of quartz remaining within fractures outside of the primary subnetwork. This variability indicates an interplay between the fracture network structure and geochemical reactions. We characterize the features controlling these processes by developing a machine learning framework to extract their relevant impact. Specifically, we use a combination of high-fidelity simulations with a graph-based approach to study geochemical reactive transport in a complex fracture network to determine the key features that control dissolution. We consider topological, geometric and hydrological features of the fracture network to predict the remaining quartz in quasi-steady state. We found that the dissolution reaction rate constant of quartz and the distance to the primary sub-network in the fracture network are the two most important features controlling the amount of quartz remaining. This study is a first step towards characterizing the parameters that control carbon mineralization using an approach with integrates computational physics and machine learning.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

AERoBOND Project Summary

Under NASA’s Convergent Aeronautics Solutions (CAS) project, the Adhesive-Free Bonding of Complex Composites (AERoBOND) project investigated off-stoichiometric epoxy polymers for fast, reliable assembly of epoxy matrix composite structures. The project goal was to demonstrate feasibility of the AERoBOND joining method by demonstrating mechanical properties greater than 80% of conventional co-cured materials while reducing structure weight by 1%. The project consisted of three convergent research areas: material and process development, systems analysis, and material and process modeling. Material and process development was the largest component of AERoBOND with approximately 6 FTE and 1WYE of support to formulate and characterize new resins, prepare carbon fiber prepregs, fabricate laminates, measure mechanical properties, analyze failure results, and select material and process improvements. The systems analysis activity estimated the potential reduction in part count and aircraft weight by comparing models of composite wing boxes with no fasteners (co-cured structure), fasteners in major joints (co-cured stringers), and fasteners in all joints. The materials and process modeling activity included a molecular model of the AERoBOND materials system to predict mechanical properties of resins with offset stoichiometry and a process model to predict the effect of resin formulation and processing conditions on the extent of mixing and degree of cure in a finished joint. As the number of airline passenger trips doubles in the next 20 years (IATA/Tourism Economics Air Passenger Forecasts, April 2019), the increased demand for new commercial aircraft is now the single greatest technical challenge to the airframe manufacturing industry. To meet efficiency requirements, new aircraft must be fabricated primarily from high performance structural composites, but manufacturing processes are inherently slow with the largest bottleneck attributed to assembly and installation of fasteners (NASA/TM–2019-220428). Manufactures of commercial transport aircraft are compelled to install more than 100,000 redundant fasteners into bonded joints to prevent failures due to unpredictable weak bonds. In structural adhesive bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Currently, bond strength assessment is only possible through destructive testing (i.e., breaking the joint). For these reasons, regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to alleviate concerns with bond performance. The AERoBOND process enables reflow of matrix resin during assembly to eliminate the material discontinuity at the interface, thereby eliminating the dependence of mechanical performance on interfacial adhesion. The AERoBOND joint is equivalent to the interlaminar region obtained during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin. Conventional co-cured structures, although too costly and complex for large-scale manufacturing, are trusted by manufacturers and regulators, and are certified for flight with few or no redundant fasteners.Systems analysis performed on a composite wing model at the scale of a single-aisle commercial transport aircraft indicated that >20,000 redundant fasteners per wing could be eliminated by implementing the AERoBOND joining method. A total weight reduction of 15% was predicted in a wing box by eliminating fasteners and thinning components that must no longer support localized fastener loads and accommodate fastener dimensions. Interlaminar shear fracture toughness measured by the end-notched flexure test was greater than 1 kJ/m2 (nearly 140% of the co-cured benchmark property), which is greatly in excess of the project goals for mechanical properties. Testing was planned to measure interlaminar tensile fracture toughness as well as interlaminar tensile and shear strengths using the same AERoBOND configuration, but was delayed due to closure of LaRC facilities during the COVID-19 pandemic. The AERoBOND process model is partially validated and available for experimental use. It allows the user to input AERoBOND process parameters such as material composition, laminate configuration, and cure cycle to predict the final cure state of the AERoBOND joint. A preliminary, multi-scale material model was developed to predict AERoBOND joint mechanical properties (stiffness and strength) based on the cure state of the joint provided by the process model. The timing for transition of this technology within NASA is excellent as NASA initiates new enduring projects to address composites manufacturing rate challenges. AERoBOND technology is well suited to AAVP/AATT objectives for rapid manufacturing of a composite wing. A minimal effort (1 FTE/$15k procurement/0 WYE) is proposed in FY21 to continue a minor mechanical testing effort and maintain a SAA with ASX composites to develop commercial quality prepreg material. An RFI with the composites industry is suggested to quantify the technology gap between the current TRL and the TRL needed for transition to industry. A moderate effort [3-4 FTE/$150k/1 WYE (~$115k)] is proposed in FY22 for the “high rate composites manufacturing” project currently in planning. The partnership with ASX Composites will be expanded to produce material for sub-element/element-scale “panel-off” activities. Industry partnerships with airframe manufacturers is an expected component to explore damage tolerance and environmental stability. Further development of multi-scale modeling tools (process model, meso-scale model, and molecular model) is planned to enhance and deliver tools for rapid manufacturing infusion.

Frank Louis Palmieri↗
DOE OSTI2022

Reduced diffusion and enhanced retention of multiple radionuclides from pore structure characterization of barrier materials for enhanced repository performance

Fluid flow and chemical transport in porous media are the macroscopic consequences of pore structure, which integrates geometry (e.g., pore size and surface area, pore-size distribution) and topology (e.g., pore connectivity). Low-permeability geological media whose pores are poorly interconnected will exhibit the characteristics of anomalous diffusion and sample size-dependent effective porosity, which will strongly impact long-term net diffusion and retention of radionuclides in geological repository settings involving different host rocks and barrier materials. A suite of innovative and complementary experimental approaches is utilized to study the microscopic pore structure and macroscopic fluid flow & chemical transport for a range of host rocks and barrier materials, in addition to standard clay minerals and reference rocks. With a particular focus on quantifying the presence and magnitude of “isolated” pores for a reduced effective porosity in low-permeability geomedia, the integrated methodologies for basic properties and pore structure characterization of these geomedia include X-ray diffraction, thin section petrography, grain size distribution, water immersion porosimetry after vacuum-pulling for full saturation, mercury intrusion porosimetry, nitrogen physisorption, scanning electron microscopy, X-ray computed tomography, and (ultra-)small angle neutron (X-ray) scattering. In addition, custom-designed gas diffusion, tracer recipe involving a range of anionic and cationic chemicals with subsequent analyses by laser ablation and inductively coupled plasma-mass spectrometry, along with batch sorption, column transport, and imbibition tests were conducted for coupled effects of pore structure and chemical retention/transport. From the perspectives of pore structure in conjunction with multiple and complementary approaches to examining a range of sample sizes under different observational scales, we find that the poor pore connectivity is prevalent in low-permeability media (mudstone and crystalline rock) that is related to geological processes (e.g., compaction, diagenesis and thermal maturation). For example, the deep and organic matter-rich mudstones have a much smaller effective porosity than the total porosity (as a result of poor pore connectivity) and associated diffusion coefficient, and the effective porosity & diffusion coefficients are also dependent upon the sample sizes used in the measurement. Similarly, most of the pore space in the shallow mudstone is also controlled by pore-throat diameters in the 5-50 nm range of intergranular pore types from its fine-grained nature, but with an overall good pore connectivity. However, the nm-sized pore space (physically pore-network architecture) and strong sorption capacities (chemical retention from clay minerals) of both shallow and deep mudstones lead to the synergistic retention of cationic radionuclides and their utilities as effective host rocks and barrier materials. Our unique approaches of studying how the micro-scale pore structure affect macro-scale fluid flow, diffusion & retention, and chemical transport produce improved mechanistic understanding, and realistic quantification, of diffusion and retention of typical radionuclides in a range of generic host rocks and barrier materials (clay/shale, salt, crystalline rock, and tuff), with the overall results leading to scientifically-based understanding of enhanced isolation (from both diffusion and retention) of radionuclides and improved confidence on the long-term performance of geological repository to store high-level radioactive wastes. In addition to the training of 25 undergraduates, graduates, and postdocs of UTA, the scientists (organizations) involved in performing this work (e.g., discussion, sample sharing, and operation of SANS and SAXS instruments) include Ed Matteo, Yifeng Wang, and Kristopher Kuhlman (Sandia National Laboratories), Jens Birkholzer, Liange Zheng, Tim Kneafsey, and Sharon Borglin (Lawrence Berkeley National Laboratory), Mavrik Zavarin (Lawrence Livermore National Laboratory), Yukio Tachi and Yuta Fukatsu (Japan Atomic Energy Agency), Mieke de Craen (Euridice, Belgium), Markus Bleuel (NIST), Wei-Ren Chen, Gergely Nagy, Changwoo Do, William Heller, Larry Anovitz, and Kenneth Littrell (ORNL), as well as Jan Illvsky, Ivan Kuzmenko, Ju-Sang Park and Jon Almers (ANL). Key deliverables include a total of 13 peer-reviewed journal articles (nine published and three under review), 23 presentations at scientific conferences (AAPG, AAPG Southwest Section, AGU, Asian Clay Conference, GSA, GSA South-Central Section, IHLRWM, InterPore, International Conference on Chemistry and Migration Behavior of Actinides and Fission Products in the Geosphere, International Conference on Coupled Processes in Fractured Geological Media: Observation, Modeling and Application), and academic institutions (UTA, New Mexico State University; University of Poitiers, France; University of Helsinki, Finland; Uppsala University, Sweden; Istanbul Technical University, Turkey) and other organizations (Andra, France; Posiva Oy, Finland).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗