Search NASA⌕ Search

SEARCH · Search NASA

Results for “SCALE MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Wind-tunnel investigation of a large-scale model of a lift-cruise fan V/STOL aircraft with extended lift-cruise nacelles

The aerodynamic characteristics of a large-scale model of a lift/cruise fan V/STOL aircraft were determined. The model was equipped with three fans, one mounted in the forward section of the fuselage in a lift mode, and two mounted on top of the wing adjacent to the fuselage in a lift/cruise mode. The data that were obtained include longitudinal and lateral-directional characteristics of the model, with the horizontal tail on and off, for both the powered-lift and cruise configurations. Lateral-directional characteristics were obtained with the horizontal and vertical tail sections removed. Powered-lift data were obtained at several wind-tunnel velocities and at several lift-cruise fan thrust vector angles by varying the position of the hooded deflectors from 0 deg (the cruise condition) to 90 deg.

Gambucci, B. J.↗
NASA NTRS1978

Quiet Clean Short-Haul Experimental Engine (QCSEE) acoustic and aerodynamic tests on a scale model over-the-wing thrust reverser and forward thrust nozzle

An acoustic and aerodynamic test program was conducted on a 1/6.25 scale model of the Quiet, Clean, Short-Haul Experimental Engine (QCSEE) forward thrust over-the-wing (OTW) nozzle and OTW thrust reverser. In reverse thrust, the effect of reverser geometry was studied by parametric variations in blocker spacing, blocker height, lip angle, and lip length. Forward thrust nozzle tests determined the jet noise levels of the cruise and takeoff nozzles, the effect of opening side doors to achieve takeoff thrust, and scrubbing noise of the cruise and takeoff jet on a simulated wing surface. Velocity profiles are presented for both forward and reverse thrust nozzles. An estimate of the reverse thrust was made utilizing the measured centerline turning angle.

Stimpert, D. L.↗
NASA NTRS1983

Pressure distributions on a 0.04-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley unitary plan wind tunnel

Pressure distribution tests on a 0.04-scale model of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests were completed in the Langley Unitary Plan Wind Tunnel (UPWT). The UPWT has two different test sections operating in the continuous mode. Each test section has its own Mach number range. The model was tested at angles of attack from -2.5 deg to 30 deg and angles of sideslip from -5 deg to 5 deg in both test sections. The test Reynolds number was 6.6 x 10 to the 6th power per meter. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel model was also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗
NASA NTRS1955

Free-Spinning-Tunnel Investigation of a 0.034-Scale Model of the Production Version of the Chance Vought F7U-3 Airplane, TED No. NACA AD 3103

An investigation of a 0.034-scale model of the production version of the Chance Vought F7U-3 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The inverted and erect spin and recovery characteristics of the model were determined for the combat loading with the model in the clean condition and the effect of extending slats was investigated. A brief investigation of pilot ejection was also performed. The results indicate that the inverted spin-recovery characteristics of the airplane will be satisfactory by full rudder reversal. If the rudders can only be neutralized because of high pedal forces in the inverted spins, satisfactory recovery will be obtained if the auxiliary rudders can be moved to neutral or against the spin provided the stick is held full forward. Optimum control technique for satisfactory recovery from erect spins will be full rudder reversal in conjunction with aileron movement to full with the spin (stick right in a right spin). Extension of the slats will have a slightly adverse effect on recoveries from (1 inverted spins but will have a favorable effect on recoveries from erect spins. The results of brief tests indicate that if a pilot is ejected during a spin while a spin-recovery parachute is extended and fully inflated, he will probably clear the tail parachute.

Klinar, Walter J.↗
NASA NTRS1955

Lateral Stability and Control Measurements of a 0.0858-Scale Model of the Lockheed XF-104 Airplane at Transonic Speeds

An investigation of the lateral stability and control effectiveness of a 0.0858-scale model of the Lockheed XF-104 airplane has been conducted in the Langley 16-foot transonic tunnel. The model has a low aspect ratio, 3.4-percent-thick wing with negative dihedral. The horizontal tail is located on top of the vertical tail. The investigation was made through a Mach number range of 0.80 to 1.06 at sideslip angles of -5 deg. to 5 deg. and angles of attack from 0 deg. to 16 deg. The control effectiveness of the aileron, rudder, and yaw damper were determined through the Mach number and angle-of-attack range. The results of the investigation indicated that the directional stability derivative was stable and that positive effective dihedral existed throughout the lift-coefficient range and Mach number range tested. The total aileron effectiveness, which in general produced favorable yaw with rolling moment, remained fairly constant for lift coefficients up to about 0.8 for the Mach number range tested. Yawing-moment effectiveness of the rudder changed little through the Mach number range. However, the yaw damper effectiveness decreased about 30 percent at the intermediate test Mach numbers.

Arabian, Donald D.↗
NASA NTRS1977

Results of an investigation of the space shuttle integrated vehicle aerodynamic heating characteristics obtained using the 0.0175-scale model 60-OTS in AEDC tunnel A during tests IH41 and IH41A

A thin skin thermocouple test was conducted to obtain heat-transfer data on the space shuttle integrated vehicle during the ascent phase of the flight profile. The test model was the 0.0175-scale thin skin thermocouple model (60-OTS) of the Rockwell International vehicle 5 configuration. The test was conducted at nominal Mach numbers of 2.5, 3.5, 4.5, and 5.5, and a free stream unit Reynolds number of 5 million per ft. Heat transfer data were obtained for angles of attack of 0, + or - 5, and 10 deg and yaw angles of 0, 3, and 6 deg. The integrated vehicle model was tested with the external tank configured with both a smooth ogive nose and an ogive nose with a spherical nose tip (nipple nose). The remainder of the test was conducted with the external tank installed alone in the tunnel.

Cummings, J. W.↗
NASA NTRS1961

Large-Angle Motion Tests, Including Spins, of A Free-Flying Radio-Controlled 0.13-Scale Model of A Twin Jet Swept Wing Fighter Airplane

An investigation has been conducted with a free-flying radio-controlled 0.15-scale model of a twin-jet swept-wing fighter airplane to determine the tendency of this design to enter spins and to evaluate the nature of the spin obtained from post-stall motions. The test results indicate that it may be difficult to obtain a developed spin on the airplane, particularly the flat-type spin. Two types of erect developed spins will be possible; one will be flat and fast rotating from which recovery may not be obtained and the other will be steeper and oscillatory from which recoveries will be satisfactory. Controls will be effective for satisfactory termination of the post-stall gyrations obtained. The recommended recovery technique from both post-stall gyrations and developed spins will be movement of the rudder to oppose the yawing rotation and simultaneous movement of the ailerons to with the rotation (stick right when turning to the right). When recovery is imminent, the stick should be moved longitudinally to neutral. It is recommended that the spin not be allowed to develop fully on this airplane. The developed-spin results obtained in the investigation were in good agreement with spin-tunnel results.

Sanger M Burk, Jr↗
NASA NTRS1973

Low gravity reorientation in a scale-model Centaur liquid-hydrogen tank

An experiment was conducted to investigate the process of liquid reorientation from one end of a scale-model Centaur liquid-hydrogen tank to the other end by means of low-level accelerations. Prior to reorientation, the liquid was stabilized at the top of the tank at a Bond number of 15. Tanks both with and without ring baffles and with tank radii of 5.5 and 7.0 centimeters were used in the study. Reorientation acceleration values were varied to obtain Bond numbers of 200 and 450. Liquid fill levels of 20 and 70 percent were used. From the data in this study, relations were developed to estimate reorientation event times in unbaffled tanks through the point of final liquid clearing from the top of the tank. The insertion of ring baffles drastically changed the reorientation flow profiles but resulted in only minor differences in the times of tank-top uncovering and liquid collection.

Salzman, J. A.↗
NASA NTRS1975

Results of oil flow visualization tests of an 0.010-scale model (52-OT) of the space shuttle orbiter-tank mated and orbiter configurations in the AEDC VKF tunnel B (IA17B)

An 0.010-scale model of the space shuttle (orbiter-tank mated and orbiter configurations) was tested in the AEDC VKF Tunnel B to investigate aerodynamic flow patterns. The tests utilized oil flow techniques to visualize the flow patterns. Tunnel free stream Mach number was 7.95 and nominal unit Reynolds number was 3.7 million per foot. Model angle of attack was varied from -5 deg through 10 deg and angle of sideslip was 0 deg and 2 deg. Photographs of resulting oil flow patterns are presented.

Daileda, J. J.↗
NASA NTRS1976

Results of tests CS4 and CS5 to investigate dynamic loads and pressures on 0.03-scale models (Ax1319-3/4 and 45-0) of mated 747 cam and space shuttle orbiter in the Boeing transonic wind tunnel

A 0.03-scale model of the 747 CAM/Orbiter was tested in an 8 x 12 foot transonic wind tunnel. Dynamic loads, pressure, and empennage flow field data were obtained using pressure transducers, strain gages, and a split film anemometer. The test variables included Mach number, angle of attack, sideslip angle, orbiter tailcone on and off, orbiter partial tailcone, orbiter nozzle air scoops, orbiter body flap angle, and orbiter elevon angle.

Source record↗
NASA NTRS1986

Pressure distributions obtained on a 0.10-scale model of the Space Shuttle Orbiter's forebody in the Ames Unitary Plan Wind Tunnel

Pressure distribution test data obtained on a 0.10-scale model of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests were completed in the Ames Unitary Wind Tunnel (UPWT). The UPWT tests were conducted in two different test sections operating in the continuous mode, the 8 x 7 feet and 9 x 7 feet test sections. Each test section has its own Mach number range, 1.6 to 2.5 and 2.5 to 3.5 for the 9 x 7 feet and 8 x 7 feet test section, respectively. The test Reynolds number ranged from 1.6 to 2.5 x 10 to the 6th power ft and 0.6 to 2.0 x 10 to the 6th power ft, respectively. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS orifices, the wind-tunnel model was also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations that existed on the Space Shuttle Columbia (OV-102) during the Orbiter Flight test program. This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel and computational data.

Siemers, P. M., III↗
NASA NTRS1947

Wind-Tunnel Tests of a 0.182-Scale Model of an F4U-1 Airplane with External Stores

Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

Silvers, H. Norman↗
NASA NTRS1973

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the space shuttle vehicle 2A to determine aerodynamic loads, volume 2

Tests were conducted in Unitary Plan wind tunnels on a 0.30 scale model of the space shuttle. Tests were conducted on the integrated configuration and on the isolated orbiter. The integrated vehicle was tested at angles of attack and sideslip from minus 8 degrees to plus 8 degrees. The isolated orbiter was tested at angles of attack from minus 15 degrees to plus 40 degrees and angles of sideslip from minus 10 degrees to plus 10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were investigated.

Spangler, R. H.↗
NASA NTRS1973

Results of tests in the MSFC 14 x 14 inch trisonic wind tunnel on a .004 scale model of the Rockwell International Space Shuttle Vehicle 3, (integrated configuration)

Experimental aerodynamic investigations were conducted during mid-July, 1973 on a .004 scale model of the Rockwell International integrated configuration Space Shuttle Vehicle 3. The purpose of the tests was three fold: (1) to determine the static stability characteristics of the integrated vehicle, utilizing the Vehicle 3 orbiter configuration; (2) to determine the effect of interstage structure and tank external fuel lines on the integrated vehicle aerodynamic characteristics; (3) to determine the effects of the aft interstage structure on orbiter aerodynamic loads. Data were recorded on the integrated vehicle (test no. 579) at angles of attack and sideslip ranging from -10 deg to 10 deg over a Mach number schedule from 0.6 to 4.96. Data were obtained on the orbiter alone in the presence of the external tank with SRB attached (test no. 580) at angles of attack from -10 deg to 10 deg over a Mach number range from .6 to 1.96. Plotted data are presented in the body axis system.

Allen, E. C.↗
NASA NTRS1974

Results of investigations on a 0.015-scale model (49-0) of the space shuttle orbiter in the NASA/Ames 3.5-foot hypersonic wind tunnel (OA87)

Experimental aerodynamic investigations were conducted on a scale model of the space shuttle orbiter, Configuration 140A/B. The objectives of this test were to: 1) verify supersonic stability and control characteristics, 2) analyze aerodynamic problem areas, 3) verify control surface effectiveness, and 4) investigate Reynolds number effects. Six-component aerodynamic force and moment data were recorded over an angle of attack range from 22 deg to 46 deg at a constant sideslip angle of 0 deg. The test Mach number was varied from 5.3 to 7.3 to 10.3. The Reynolds number per unit length was varied from 805,000 to 10 million per foot.

Petrozzi, M. T.↗