Search NASA⌕ Search

SEARCH · Search NASA

Results for “SYSTEMS MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Distributed Learning of Mode Shapes in Power System Models

We address the problem of distributed estimation of eigenvectors for power system models using online phasor measurements. The power system is considered to be divided into a set of non-overlapping areas, each of which is equipped with a local estimator. Online measurements of bus voltage and current phasors are first used to generate estimates of the generator states in each area using decentralized Kalman filters. Thereafter, these estimates are used for identifying a reduced-order model of the system in a completely distributed way by sharing state information between the estimators over a strongly connected communication graph. The identified model is then utilized to estimate its right eigenvectors over the same distributed graph. Results are validated using a 50-bus power system model with four areas.

Gusrialdi, Azwirman↗

Nine time steps: ultra-fast statistical consistency testing of the Community Earth System Model (pyCECT v3.0)

The Community Earth System Model Ensemble Consistency Test (CESM-ECT) suitewas developed as an alternative to requiring bit wise identical output for quality assurance. This objective test provides a statistical measurement of consistency between an accepted ensemble created by small initial temperature perturbations and a test set of CESM simulations. Here, we extend the CESM-ECT suite with an inexpensive and robust test for ensemble consistency that is applied to Community Atmospheric Model (CAM) output after only nine model time steps. We suggest that adequate ensemble variability is achieved with instantaneous variable values at the ninth step, despite rapid perturbation growth and heterogeneous variable spread. We refer to this new test as the Ultra-Fast CAM Ensemble Consistency Test (UF-CAM-ECT) and demonstrate its effectiveness in practice, including its ability to detect small-scale events and its applicability to the Community Land Model (CLM).The new ultra-fast test facilitates CESM development, porting, and optimization efforts, particularly when used to complement information fromthe original CESM-ECT suite of tools.

58 GEOSCIENCES↗

Representation of the Community Earth System Model (CESM1) CAM4-chem within the Chemistry-Climate Model Initiative (CCMI)

The Community Earth System Model (CESM1) CAM4-chem has been used to perform the Chemistry Climate Model Initiative (CCMI) reference and sensitivity simulations. In this model, the Community Atmospheric Model version 4 (CAM4) is fully coupled to tropospheric and stratospheric chemistry. Details and specifics of each configuration, including new developments and improvements are described. CESM1 CAM4-chem is a low-top model that reaches up to approximately 40 km and uses a horizontal resolution of 1.9° latitude and 2.5° longitude. For the specified dynamics experiments, the model is nudged to Modern-Era Retrospective Analysis for Research and Applications (MERRA) reanalysis. We summarize the performance of the three reference simulations suggested by CCMI, with a focus on the last 15 years of the simulation when most observations are available. Comparisons with selected data sets are employed to demonstrate the general performance of the model. We highlight new data sets that are suited for multi-model evaluation studies. Most important improvements of the model are the treatment of stratospheric aerosols and the corresponding adjustments for radiation and optics, the updated chemistry scheme including improved polar chemistry and stratospheric dynamics and improved dry deposition rates. These updates lead to a very good representation of tropospheric ozone within 20 % of values from available observations for most regions. In particular, the trend and magnitude of surface ozone is much improved compared to earlier versions of the model. Furthermore, stratospheric column ozone of the Southern Hemisphere in winter and spring is reasonably well represented. In conclusion, all experiments still underestimate CO most significantly in Northern Hemisphere spring and show a significant underestimation of hydrocarbons based on surface observations.

54 ENVIRONMENTAL SCIENCES↗

Multitemporal and Multiscaled Fractal Analysis of Landsat Satellite Data Using the Image Characterization and Modeling System (ICAMS)

The Image Characterization And Modeling System (ICAMS) is a public domain software package that is designed to provide scientists with innovative spatial analytical tools to visualize, measure, and characterize landscape patterns so that environmental conditions or processes can be assessed and monitored more effectively. In this study ICAMS has been used to evaluate how changes in fractal dimension, as a landscape characterization index, and resolution, are related to differences in Landsat images collected at different dates for the same area. Landsat Thematic Mapper (TM) data obtained in May and August 1993 over a portion of the Great Basin Desert in eastern Nevada were used for analysis. These data represent contrasting periods of peak "green-up" and "dry-down" for the study area. The TM data sets were converted into Normalized Difference Vegetation Index (NDVI) images to expedite analysis of differences in fractal dimension between the two dates. These NDVI images were also resampled to resolutions of 60, 120, 240, 480, and 960 meters from the original 30 meter pixel size, to permit an assessment of how fractal dimension varies with spatial resolution. Tests of fractal dimension for two dates at various pixel resolutions show that the D values in the August image become increasingly more complex as pixel size increases to 480 meters. The D values in the May image show an even more complex relationship to pixel size than that expressed in the August image. Fractal dimension for a difference image computed for the May and August dates increase with pixel size up to a resolution of 120 meters, and then decline with increasing pixel size. This means that the greatest complexity in the difference images occur around a resolution of 120 meters, which is analogous to the operational domain of changes in vegetation and snow cover that constitute differences between the two dates.

Quattrochi, Dale A.↗

The Dynamics of Cascaded Monod System Models Through Five Levels

A Monod system model is a set of ordinary differential equations where the terms resemble those which Monod described in his 1949 paper. We focus on the multiple trophic level case in which each trophic level uses only one of the trophic levels for its perpetuation, and no two trophic entities use the same trophic cascaded level. The treatment derives from a primary producer progressively through five trophic levels. Stability types are identified and are related to persistence, and the consequences of some intuitive scaling structures are developed. These considerations are useful to some theoretical questions in ecology and to applications such as bioreactor operation.

Blackwell, Charles C.↗

The Madden–Julian Oscillation in the Energy Exascale Earth System Model Version 1

Abstract The present study examines the characteristics of the Madden–Julian Oscillation (MJO) events represented in the Energy Exascale Earth System Model version 1 (E3SMv1), DOE’s new Earth system model. The coupled E3SMv1 realistically simulates the eastward propagation of precipitation and moist static energy (MSE) anomalies associated with the MJO. As in observations, horizontal moisture advection and longwave radiative feedback are found to be the dominant processes in E3SMv1 that lead to the eastward movement and maintenance of the MJO MSE anomalies, respectively. Modulation of the diurnal cycle of precipitation in the Maritime Continent region by the MJO is also well represented in the model despite systematic biases in the magnitude and phase of the precipitation diurnal cycle. On the MJO impact over the midlatitude, E3SMv1 reasonably captures the pattern of the MJO teleconnections across the North Pacific and North America, with improvement in the performance in a high‐resolution version, despite the magnitude being a bit weaker than the observed. Regarding the interannual variability of the MJO, the El Niño‐Southern Oscillation (ENSO) modulation of the zonal extent of MJO’s eastward propagation, as well as associated changes in the mean state moisture gradient in the tropical west Pacific, are well reproduced in the model. However, MJO in E3SMv1 exhibits no sensitivity to the Quasi‐Biennial Oscillation (QBO), with the MJO propagation characteristics being almost identical between easterly QBO and westerly QBO years. Processes that have been suggested as critical to MJO simulation are also examined by utilizing recently developed process‐oriented diagnostics.

54 ENVIRONMENTAL SCIENCES↗

Subseasonal Tropical Convection Characteristics in the Energy Exascale Earth System Model Version 2

Accurate simulation of subseasonal tropical moist convection remains a key challenge for Earth system models. The difficulties stem from the reliance of cumulus cloud processes on model parameterizations and the need to represent the multiscale nature of interactions among clouds, radiation, moisture, circulation, and surface energy fluxes. Equatorial convection drives circulation anomalies that can affect weather patterns and extremes globally, motivating efforts to better understand and simulate these tropical disturbances. Here, a detailed review of subseasonal tropical convective behavior as simulated in the Energy Exascale Earth System Model version 2 (E3SMv2) is presented, with comparison to its predecessor version 1 (E3SMv1) and reference data sets. Model structural changes to the deep convective trigger function and surface fluxes, along with parametric tuning of the cloud and microphysics schemes, together result in an improved depiction of organized tropical convection across scales. In particular, E3SMv2 exhibits a more realistic Madden‐Julian oscillation (MJO) and low‐frequency Kelvin waves—owing to a sharper time mean equatorial meridional moisture gradient and improved convection‐circulation coupling —as well as a better depiction of MJO Northern Hemisphere teleconnections. Despite these improvements, subseasonal precipitation variance continues to be strongly underestimated in E3SMv2. Use of a cloud plume model also reveals that the coupling between daily averaged tropical precipitation and lower tropospheric instability in E3SM is inconsistent with observations, a bias that could potentially impact the simulation of intraseasonal disturbances.

54 ENVIRONMENTAL SCIENCES↗

AI-Enhanced Computational Tools for Entry Systems Modeling

To advance the understanding of complex atmospheric entry phenomena, NASA’s Entry Systems Modeling (ESM) team [1] has developed high-fidelity computational tools addressing multiscale challenges, from material microstructures to full-scale heatshield response. This abstract highlights a subset of ESM tools, focusing on AI integration to enhance workflows and predictive modeling. - PuMA [2] computes effective material properties from high-resolution micro-CT scans, supporting TPS analysis for NASA missions. - TomoSAM [3] automates 3D tomography dataset segmentation for PuMA using the Segment Anything Model, reducing manual effort and improving accuracy. - PATO [4] models porous reactive materials under extreme conditions, with advancements such as unified solvers, mechanical erosion, and TPS coatings for NASA missions. - arcjetCV [5] employs deep learning to analyze arc jet test footage, measuring recession rates, shape changes, and shock standoff distances, bridging simulations, and experiments to reveal TPS ablation behavior. - ARCHeS [6] simulates arc heater plasma flows, modeling turbulence, radiation, and electromagnetic interactions to optimize arc heater performance, validate TPS under extreme conditions, and serve as a foundation for developing digital twins of arc heater facilities. - SPARTA [7] simulates rarefied hypersonic flows and gas-surface interactions for planetary entry missions, leveraging GPU architectures for scalable and efficient aerothermal and ablation analyses. AI-driven solutions, such as deep learning segmentation, have streamlined workflows in ESM tools and still hold significant potential to further accelerate processes and enhance automation in entry systems modeling. [1] Haskins, J.B. (2023), [2] Ferguson, J.C. (2018), [3] Meurisse, J.B.E. (2018), [4] Semeraro, F. (2023), [5] Quintart, A. (2024) [6] Meurisse, J.B.E. (2022), [7] Plimpton, S.J. (2019)

Predictive Modeling↗

Earth System Model Improvement Pipeline via Uncertainty Attribution and Active Learning

Primary focal area: 2 (Predictive Modeling via AI): We develop methods to formally quantify uncertainties in Earth System models for the land-atmosphere coupled system. Science Challenge: Earth system models still have significant biases in historical predictions of the intensity and frequency of water cycling extremes (e.g., droughts and flood events), leading to low confidence in future projections. Uncertainties arise from incomplete understanding of land and atmospheric processes, and insufficient observational constraints on model parameters. Many observations, including those from key DOE investments such as ARM and AmeriFlux, are used to evaluate model performance but have not been used to formally quantify model uncertainty because of the expense of running ESM simulations. An efficient pipeline engaging cutting-edge machine learning (ML) and uncertainty quantification (UQ) methods is needed to improve the predictive understanding of water cycle extremes in the Earth system.

54 ENVIRONMENTAL SCIENCES↗

Evaluation of the atmosphere–land–ocean–sea ice interface processes in the Regional Arctic System Model version 1 (RASM1) using local and globally gridded observations

The Regional Arctic System Model version 1 (RASM1) has been developed to provide high-resolution simulations of the Arctic atmosphere–ocean–sea ice–land system. Here, we provide a baseline for the capability of RASM to simulate interface processes by comparing retrospective simulations from RASM1 for 1990–2014 with the Community Earth System Model version 1 (CESM1) and the spread across three recent reanalyses. Evaluations of surface and 2 m air temperature, surface radiative and turbulent fluxes, precipitation, and snow depth in the various models and reanalyses are performed using global and regional datasets and a variety of in situ datasets, including flux towers over land, ship cruises over oceans, and a field experiment over sea ice. These evaluations reveal that RASM1 simulates precipitation that is similar to CESM1, reanalyses, and satellite gauge combined precipitation datasets over all river basins within the RASM domain. Snow depth in RASM is closer to upscaled surface observations over a flatter region than in more mountainous terrain in Alaska. The sea ice–atmosphere interface is well simulated in regards to radiation fluxes, which generally fall within observational uncertainty. RASM1 monthly mean surface temperature and radiation biases are shown to be due to biases in the simulated mean diurnal cycle. At some locations, a minimal monthly mean bias is shown to be due to the compensation of roughly equal but opposite biases between daytime and nighttime, whereas this is not the case at locations where the monthly mean bias is higher in magnitude. These biases are derived from errors in the diurnal cycle of the energy balance (radiative and turbulent flux) components. Therefore, the key to advancing the simulation of SAT and the surface energy budget would be to improve the representation of the diurnal cycle of radiative and turbulent fluxes. The development of RASM2 aims to address these biases. Still, an advantage of RASM1 is that it captures the interannual and interdecadal variability in the climate of the Arctic region, which global models like CESM cannot do.

58 GEOSCIENCES↗

Altered TNF-Alpha, Glucose, Insulin and Amino Acids in Islets Langerhans Cultured in a Microgravity Model System

The present studies were designed to determine effects of a microgravity model system upon lipopolysaccharide (LPS) stimulated tumor necrosis factor alpha (TNF-alpha) activity and indices of insulin and fuel homeostasis of pancreatic islets of Langerhans. Islets (1726+/-1 17,150 u IEU) from Wistar Furth rats were treated as: 1) HARV (High Aspect Ratio Vessel cell culture) , 2) HARV plus LPS, 3) static culture, 4) static culture plus LPS. TNF-alpha (L929 cytotoxicity assay) was significantly increased in LPS-induced HARV and static cultures, yet the increase was more pronounced in the static culture group (p<0.05). A decrease in insulin concentration was demonstrated in the LPS stimulated HARV culture (p<0.05). We observed a greater glucose concentration and increased disappearance of arginine in islets cultured in HARVs. While nitrogenous compound analysis indicated a ubiquitous reliance upon glutamine in all experimental groups, arginine was converted to ornithine at a two-fold greater rate in the islets cultured in the HARV microgravity model system (p<0.05). These studies demonstrate alterations in LPS induced TNF-alpha production of pancreatic islets of Langerhans, favoring a lesser TNF activity in the HARV. These alterations in fuel homeostasis may be promulgated by gravity averaged cell culture methods or by three dimensional cell assembly.

Tobin, Brian W.↗

Implementation of an Orographic Drag Scheme Considering Orographic Anisotropy in All Flow Directions in the Earth System Model CAS‐ESM 2.0

Abstract A reasonable representation of orographic anisotropy in earth system models is vital for improving weather and climate modeling. In this study, we implement the orographic drag scheme, including 3‐D orographic anisotropy (3D‐AFD), into the Chinese Academy of Sciences Earth System Model version 2 (CAS‐ESM 2.0). Three groups of simulations named sensitivity run, medium‐range forecast, and seasonal forecast respectively are conducted using the updated CAS‐ESM model and validated against station observation and reanalysis data. These simulations are run using the three schemes—3D‐AFD scheme, the 3D orographic anisotropy scheme for the eight‐direction (3D‐8x), and the 2D isotropic scheme (2D)—to compare their performance in CAS‐ESM 2.0. Sensitivity runs show that the 3D‐AFD provide more continuous transition of calculated drag as function of wind direction than the 3D‐8x, while the drag calculated using the 2D scheme show no variation with change of wind direction. Enhanced drag in the medium range and seasonal forecast using the updated CAS‐ESM alleviates part of the winter wind speed bias over the Tibetan Plateau (TP) and the cold bias over TP and the Siberian polar region. It is shown that the 3D‐AFD scheme alleviates more bias than that of the 3D‐8x scheme (by wind speed reduction of 1 ∼ 2 m/s and temperature of 1 ∼ 2 K) especially in the seasonal forecast. The results suggest that reasonable representation of the orographic anisotropy is important in climate modeling.

Xie, Jinbo↗

Advances in Geologic Disposal System Modeling and Application to Crystalline Rock

The Used Fuel Disposition Campaign (UFDC) of the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), Office of Fuel Cycle Technology (OFCT) is conducting research and development (R&D) on geologic disposal of used nuclear fuel (UNF) and high-level nuclear waste (HLW). Two of the high priorities for UFDC disposal R&D are design concept development and disposal system modeling (DOE 2011). These priorities are directly addressed in the UFDC Generic Disposal Systems Analysis (GDSA) work package, which is charged with developing a disposal system modeling and analysis capability for evaluating disposal system performance for nuclear waste in geologic media (e.g., salt, granite, clay, and deep borehole disposal). This report describes specific GDSA activities in fiscal year 2016 (FY 2016) toward the development of the enhanced disposal system modeling and analysis capability for geologic disposal of nuclear waste. The GDSA framework employs the PFLOTRAN thermal-hydrologic-chemical multi-physics code and the Dakota uncertainty sampling and propagation code. Each code is designed for massively-parallel processing in a high-performance computing (HPC) environment. Multi-physics representations in PFLOTRAN are used to simulate various coupled processes including heat flow, fluid flow, waste dissolution, radionuclide release, radionuclide decay and ingrowth, precipitation and dissolution of secondary phases, and radionuclide transport through engineered barriers and natural geologic barriers to the biosphere. Dakota is used to generate sets of representative realizations and to analyze parameter sensitivity.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Collaborative Proposal: Improving Decadal Prediction of Arctic Climate Variability and Change Using a Regional Arctic System Model (RASM)

RASM is a multi-disciplinary project, which brings together researchers from six state universities, one military postgraduate school, and one DoE laboratory to address the core modeling objectives of the arctic research community articulated in the Arctic System Modeling report by Roberts et al. (2010b). This report advocates the construction of a regional downscaling tool to generate probabilistic decadal projections of Greenland ice sheet retreat, evolution of arctic sea ice cover, changes in land surface vegetation, and regional processes leading to arctic amplification. Unified coupled models such as RASM are ideal for this purpose because they simulate fine-scale physics, essential for the realistic representation of intra-annual variability, in addition to processes fundamental to long term climatic shifts (Hurrell et al. 2009). By using RASM with boundary conditions from a global model, we can generate many-member ensembles essential for understanding uncertainty in regional climate projections (Hawkins and Sutton 2009). This probabilistic approach is computationally prohibitive for high-resolution global models in the foreseeable future, and also for regional models interactively nested within global simulations. Yet it is fundamental for quantifying uncertainty in decadal forecasts to make them useful for decision makers (Doherty et al. 2009). For this reason, we have targeted development of ensemble generation techniques as a core project task (Task 4.5). Environmental impact assessment specialists need high-fidelity regional ensemble projections to improve the accuracy of their work (Challinor et al. 2009; Moss et al. 2010). This is especially true of the Arctic, where economic, social and national interests are rapidly reshaping the high north in step with regional climate change. During the next decade, considerable oil and gas discoveries are expected across many parts of the marine and terrestrial Arctic (Gautier et al. 2009), the economics of the Northern Sea Route will steadily improve (Arctic Council 2009), and sovereign claims over the Arctic Ocean will increasingly be subject to international negotiations (Proelss 2009). Issues such as these have led to an expanding demand for Arctic climate projections to aid national and commercial decisions. However, detailed information from existing models is lacking. RASM will enhance the existing Arctic system modeling capabilities and align them with the scientific and societal needs outlined above. The science involved in the development of RASM will be integrated with teaching and training at a few different levels. RASM PIs will supervise at least six postdoctoral and doctoral students with additional involvement of undergraduate research assistants. RASM postdoctoral fellows and graduate trainees will benefit from being a part of a large, collaborative, and multi-disciplinary research projects employing state-of-the-art modeling and computational tools. They will also have the opportunity to contribute to the UTEP-led education and outreach effort developed specifically for RASM. The UTEP team will use RASM as a platform for education and outreach. First, we will develop products for public dissemination, such as curriculum units, lesson plans and other materials (simulations, movies, and images) for use by students and teachers in high school and university classrooms. Second, we will facilitate bringing RASM PIs, postdocs, and graduate students into the classroom, through electronic mentorship and by contributing content via online lectures and presentations. Third, by the use of problem-based learning (PBL) approaches, we will provide real-world scenarios and problems enabling students to do research and develop position papers or presentations on topics related to RASM. (Problem-based learning is a student-centered, inquiry-based approach in which students work in teams to solve challenging, open-ended problems.) Fourth, we will develop teacher-training materials that will be developed into workshops (face-to-face or online) to help teachers understand how to use the materials we supply. Overall, we will provide a broad, and long-term RASM program for education and outreach. RASM education and outreach activities will target underrepresented populations - in particular, Hispanic students and teachers. For example, the UTEP student body is more than 70 percent Hispanic and 55 percent female, and the majority of students are the first in their families to attend college. Students from underrepresented groups will be given the chance to expand their understanding of the different scientific knowledge and processes associated with RASM. We will develop an eye-catching RASM website to include information about the project, model results and educational materials, and lists of RASM publications and presentations.

54 ENVIRONMENTAL SCIENCES↗

Dynamic-Feature Extraction, Attribution and Reconstruction (DEAR) Method for Power System Model Reduction

In interconnected power systems, dynamic model reduction can be applied on generators outside the area of interest to mitigate the computational cost with transient stability studies. This paper presents an approach of deriving the reduced dynamic model of the external area based on dynamic response measurements, which comprises of three steps, dynamic-feature extraction, attribution and reconstruction (DEAR). In the DEAR approach, a feature extraction technique, such as singular value decomposition (SVD), is applied to the measured generator dynamics after a disturbance. Characteristic generators are then identified in the feature attribution step for matching the extracted dynamic features with the highest similarity, forming a suboptimal ‘basis’ of system dynamics. In the reconstruction step, generator state variables such as rotor angles and voltage magnitudes are approximated with a linear combination of the characteristic generators, resulting in a quasi-nonlinear reduced model of the original external system. Network model is un-changed in the DEAR method. Tests on several IEEE standard systems show that the proposed method gets better reduction ratio and response errors than the traditional coherency aggregation methods.

Dynamic response, model reduction, orthogonal deco↗

SU-F-J-41: Experimental Validation of a Cascaded Linear System Model for MVCBCT with a Multi-Layer EPID

Purpose: The purpose of this study was to validate the use of a cascaded linear system model for MV cone-beam CT (CBCT) using a multi-layer (MLI) electronic portal imaging device (EPID) and provide experimental insight into image formation. A validated 3D model provides insight into salient factors affecting reconstructed image quality, allowing potential for optimizing detector design for CBCT applications. Methods: A cascaded linear system model was developed to investigate the potential improvement in reconstructed image quality for MV CBCT using an MLI EPID. Inputs to the three-dimensional (3D) model include projection space MTF and NPS. Experimental validation was performed on a prototype MLI detector installed on the portal imaging arm of a Varian TrueBeam radiotherapy system. CBCT scans of up to 898 projections over 360 degrees were acquired at exposures of 16 and 64 MU. Image volumes were reconstructed using a Feldkamp-type (FDK) filtered backprojection (FBP) algorithm. Flat field images and scans of a Catphan model 604 phantom were acquired. The effect of 2×2 and 4×4 detector binning was also examined. Results: Using projection flat fields as an input, examination of the modeled and measured NPS in the axial plane exhibits good agreement. Binning projection images was shown to improve axial slice SDNR by a factor of approximately 1.4. This improvement is largely driven by a decrease in image noise of roughly 20%. However, this effect is accompanied by a subsequent loss in image resolution. Conclusion: The measured axial NPS shows good agreement with the theoretical calculation using a linear system model. Binning of projection images improves SNR of large objects on the Catphan phantom by decreasing noise. Specific imaging tasks will dictate the implementation image binning to two-dimensional projection images. The project was partially supported by a grant from Varian Medical Systems, Inc. and grant No. R01CA188446-01 from the National Cancer Institute.

60 APPLIED LIFE SCIENCES↗

Using an Explainable Machine Learning Approach to Characterize Earth System Model Errors: Application of SHAP Analysis to Modeling Lightning Flash Occurrence

Abstract Computational models of the Earth System are critical tools for modern scientific inquiry. Efforts toward evaluating and improving errors in representations of physical and chemical processes in these large computational systems are commonly stymied by highly nonlinear and complex error behavior. Recent work has shown that these errors can be effectively predicted using modern Artificial Intelligence (A.I.) techniques. In this work, we go beyond these previous studies to apply an explainable A.I. technique to not only predict model errors but also move toward understanding the underlying reasons for successful error prediction. We use XGBoost classification trees and SHapley Additive exPlanations analysis to explore the errors in the prediction of lightning occurrence in the NASA Goddard Earth Observing System model, a widely used Earth System Model. This explainable error prediction system can effectively predict the model error and indicates that the errors are strongly related to convective processes and the characteristics of the land surface.

54 ENVIRONMENTAL SCIENCES↗