Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scanning microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Radiation-induced alteration of sandstone concrete aggregate

This study investigates the alteration of felsic sandstone-type rock, which is used as a coarse aggregate in concrete, subject to the effects of gamma-ray and neutron irradiation. The effects of three gamma-ray doses (27, 55, and 108 MGy) and four neutron fluence levels (1.22, 2.19, 6.99, and 14.30 × 10 19 n/cm 2 , $E$ ≥ 0.01 MeV) were investigated. Quartz and albite were found to be the major rock-forming minerals, with microcline intermediates, chlorite, and muscovite as the minors. Gamma rays caused no significant changes to the physical properties of the sandstone aggregates, even at high doses (108 MGy). In contrast, neutron irradiation caused alterations that became more pronounced at higher neutron fluences. The solid was confirmed to expand through metamictization of the rock-forming minerals. Quartz and muscovite were the most affected phases, whereas albite and microcline intermediates were only slightly affected, and chlorite was almost unaffected. The decrease in density was measured by He and water pycnometry, and this value was almost reproduced by calculations using the rock-forming mineral composition of the pristine sample measured using X-ray powder diffraction/Rietveld analysis and the cell volume change of the major forming minerals. In addition, light optical microscopy and scanning electron microscopy images confirmed the presence of intergranular and intragranular cracks. Intergranular cracks appeared to have initiated from the quartz grains, which expanded significantly. The intragranular cracks were frequently observed in the albite and microcline intermediates. These cracks can be described as radial cracks starting from the expanding quartz, caused by enforced displacement for deformation consistency with quartz expansion. The crack area ratio quantified by SEM image analysis corresponds to the discrepancy of the volume expansion difference calculated by He or water pycnometry and dimensional change measurements. In conclusion, an evaluation of solid expansion and crack openings in aggregates is important to estimate concrete degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Phase transition in two-dimensional monolayer (1L)-molybdenum disulfide induced by atomic S-basal plane gliding via synchrotron X-ray monochromatic beam radiation for superior electronic performance

Here, in this work, we report a novel approach to reduce the channel resistance by inducing a phase transition behavior from 2H to 1T in a monolayer MoS 2 (1L-MoS 2 ) by a synchrotron X-ray monochromatic beam (mono-beam) radiation. The effects of the biphase structure by the mono-beam on the 1L-MoS2 film were investigated using Raman spectra, photoluminescence (PL) spectra, scanning tunneling microscopy, and scanning tunneling spectroscopy, respectively. Through material characterization, we identified that the lateral sliding of S-vacancies along the S-plane in the 1L-MoS 2 is the key reason for the origin of unidirectional phase transition. The precise phase engineering triggered by the mono-beam radiation process allows the realization of field-effect transistors (FET) with 2X improvement in mobility toward a high on/off ratio (~10 8 ) and a near-ideal subthreshold swing of ~88 mV per decade. The validity of the phase engineering could be further extended for its application as a memory device, exhibiting a gate tunable conduction modulation behavior and a high resistance ratio of ~10 2 at a gate bias of 5 V with endurance of ~100 cycles. Furthermore, an artificial neural network using the synaptic weight update with accuracy of ~93 % was achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Chalcogenide perovskite BaZrS 3 thin-film electronic and optoelectronic devices by low temperature processing

Owing to its superior visible light absorption and high chemical stability, chalcogenide perovskite barium zirconium sulfide (BaZrS 3 ) has attracted significant attention in the past few years as a potential alternative to hybrid halide perovskites for optoelectronics. However, the high processing temperatures of BaZrS 3 thin films at above 1000 °C severely limits their potential for device applications. Herein, we report the synthesis of BaZrS 3 thin films at temperatures as low as 500 °C, by changing the chemical reaction pathway. The single phase BaZrS 3 thin film was confirmed by X-ray diffraction and Raman spectroscopy. Atomic force microscopy and scanning electron microscopy show that crystalline size and surface roughness were consistently reduced with decreasing annealing temperature. The lower temperatures further eliminate sulfur vacancies and carbon contaminations associated with high temperature processing. The ability to synthesize chalcogenide perovskite thin films at lower temperatures removes a major hurdle for their device fabrication. The photodetectors demonstrate fast response and an on/off ratio of 80. Finally, the fabricated field effect transistors show an ambipolar behavior with electron and hole mobilities of 16.8 cm 2 /Vs and 2.6 cm 2 /Vs, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structural properties of aqueous grown polydopamine thin films determined by neutron reflectometry

Here, in this work, neutron reflectometry (NR) studies of the bio-mimetic polymer, polydopamine (PDA), deposited from differing initial concentrations of precursor material dopamine hydrochloride for a range of polymerization times, is reported. PDA can form a complex and highly versatile polymer film, with many structure studies having been performed previously, but a comprehensive structural determination of PDA by NR is lacking in the literature. It was found that simple box models were incapable of fully explaining the observed data, necessitating the use of a composite model consisting of the weighted average of both the 1 and 2 box models to fully capture the heterogeneous nature of the PDA film structure. Confocal laser scanning microscopy (CLSM) and atomic force microscopy (AFM) were performed to capture the surface structure and relative mechanical difference between the separate domains of the PDA. The CLSM results provide evidence that the PDA domains are larger than the coherent scattering length of a neutron used in these measurements, 10μm, supporting the need for a composite model. The AFM measurements show complex structure below the coherence length provide physical justification for the two box model. It was determined that film structure and quality are both heavily impacted by the initial concentration of dopamine hydrochloride and the polymerization time, giving confidence to the highly customizable nature of PDA as an adhesion promoting interface treatment in composite systems, such as plastic bonded explosives (PBX).

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of 316 stainless steel powder processing conditions on microstructure

One parameter that has both economic and performance effects in the manufacturing of steel parts is the powder feedstock used. 316 L steel powder can be produced through water atomization or gas atomization, where both the powder size and the atomization process determine the cost of powder feedstock. Gas atomized powder is spherical and has a lower oxygen content than water atomized powder, making it the preferred choice for performance, but comes at a higher financial cost. Here, in this study, various 316 L powder batches are characterized to understand physical properties and microstructural variations. Density and flowability were determined using gas pycnometry and Hall flow tests. Powder morphology and porosity were qualitatively analyzed via optical microscopy and scanning electron microscopy, Finally, transmission electron microscopy was used to determine changes in phases present. Spherical gas atomized powder of 30–100 μm contained Mn$-$Si rich oxides both on the surface and within the matrix. Meanwhile, irregular water atomized powder 30 μm in diameter contained silicon oxides without manganese. All powder particles contained a nickel rich cellular structure which was shown to support the formation of additional phases. While literature has observed general microstructural features across 316 L powder particles, transmission electron microscopy (TEM) in this study has identified variations in precipitation and cell structures. Information regarding morphology, flowability, density, and phase distributions can be applied to understand variations in part consolidation, which will in turn show which powder aspects are significant for production.

Chemical segregation↗
DOE OSTI2023

Field retrieved photovoltaic backsheet survey from diverse climate zones: Analysis of degradation patterns and phenomena

Understanding the impact of climate stressors on photovoltaic (PV) backsheet degradation in real-use conditions is critical to improve the accelerated testing exposures, extend the backsheet lifetime, and increase the confidence in PV reliability. Here, in this work, a total of 33 PV module backsheets were retrieved from six climatic zones worldwide with 2 - 28 years of exposure. These modules included five types of backsheet air-side materials (or outer layer): poly(vinylidene fluoride) (PVDF), poly(tetrafluoroethylene-co-hexafluoropropylene-co-vinylidene fluoride) (THV), poly(vinyl fluoride) (PVF), poly(ethylene terephthalate) (PET), and polyamide (PA). Attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) was used to identify air-side materials. The degradation induced color change, gloss loss, and chemical material changes analyzed using optical microscopy, differential scanning calorimetry (DSC), scanning electron microscopy (SEM), colorimetry (yellowness index (YI)), and gloss measurements. PVDF, THV, and PVF air-side layer backsheets, in particular PVF, had minimal degradation in the air-side layer appearance and chemical structures after exposure in different climatic zones. The PET air-side backsheets exhibited obvious color increase (22.55 YI units after about 9 years exposure) and the PA/PA/PA backsheets showed large gloss loss (up to 76.4 %) relative to the unexposed backsheets. Severe cracks between cells that penetrated through the entire thickness of backsheets are observed on PA/PA/PA backsheets after 4-6 years of exposure in 6 climatic zones. The current indoor exposure standards were not sufficient to identify this degradation type. However, fluoropolymer based PV backsheets showed lower levels of degradation predictors and increased climatic resistance. Specific samples (PVF) showed little change from baseline after 28 years of outdoor exposure.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Comparison of three measurement modalities for 3D characterization of manufactured features and process-induced porosity in titanium alloy additively manufactured parts

Nondestructive characterization of internal features and defects within complex components is vital for many industrial applications, particularly with the advent of additive manufacturing (AM) technologies. However, community understanding of the limitations of nondestructive methods such as X-ray Computed Tomography (CT) can be limited in certain industrial sectors as these may be emergent applications. In this paper, we investigate the limits of X-ray CT measurements and compare extracted data with mechanical polishing serial sectioning (MPSS) and confocal laser scanning microscopy (CLSM). The test object is an additively manufactured titanium alloy disk that contains both process-induced porosity and machined features, including focused ion beam milled features designed to probe the resolution limits of X-ray CT. Results show that each of these characterization techniques has advantages and disadvantages. We compare data acquisition times, spatial resolution, geometric measurement accuracy and defect visualization fidelity across these modalities to establish a practical framework.

Additive manufacturing↗
DOE OSTI2020

Hollow Au Nanosphere-Cu 2 O Core–Shell Nanostructures with Controllable Core Surface Morphology

Design of metal-semiconductor interfaces and heterostructures is of strong interest for various catalytic applications including photocatalysis. Here, a series of hollow Au nanosphere (HGN)-Cu 2 O core-shell nanostructures with varying core surface rugosities are synthesized and investigated for possible photocatalytic applications. HGN surface rugosity is tuned by pH modification during galvanic exchange, and carboxyl groups are utilized as coordination sites to deposit uniform Cu 2 O shells onto the gold surfaces. Final core-shell structures are verified by transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), and X-ray diffraction (XRD). Information regarding chemical state and electronic band structure is acquired by X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS). Ultrafast transient absorption (TA) reveals that charge separation in bumpy HGN (bHGN)-Cu 2 O may effectively provide longer-lived photoexcited carriers, offering great potential for utilization in advanced photocatalytic processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reaction of Hydrazine with Solution- and Vacuum-Prepared Selectively Terminated Si(100) Surfaces: Pathways to the Formation of Direct Si–N Bonds

Here, the reactivity of liquid hydrazine (N 2 H 4 ) with respect to H-, Cl-, and Br-terminated Si(100) surfaces was investigated to uncover the principles of nitrogen incorporation into the interface. This process has important implications in a wide variety of applications, including semiconductor surface passivation and functionalization, nitride growth, and many others. The use of hydrazine as a precursor allows for reactions that exclude carbon and oxygen, the primary sources of contamination in processing. In this work, the reactivity of N 2 H 4 with H- and Cl-terminated surfaces prepared by traditional solvent-based methods and with a Br-terminated Si(100) prepared in ultrahigh vacuum was compared. The reactions were studied with X-ray photoelectron spectroscopy, atomic force microscopy, and scanning tunneling microscopy, and the observations were supported by computational investigations. The H-terminated surface led to the highest level of nitrogen incorporation; however, the process proceeds with increasing surface roughness, suggesting possible etching or replacement reactions. In the case of Cl-terminated (predominantly dichloride) and Br-terminated (monobromide) surfaces, the amount of nitrogen incorporation on both surfaces after the reaction with hydrazine was very similar despite the differences in preparation, initial structure, and chemical composition. Density functional theory was used to propose the possible surface structures and to analyze surface reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

An Impedance Humidity Sensor Based on CVD Grown WSe 2 2D Films

2D materials-based planar devices have been sought after for gas and humidity sensor applications owing to their high sensitivity due to their ultrathin nature and increased surface area. Herein, 2D WSe 2 films-based planner devices were fabricated to evaluate their performance for potential application in humidity sensors. The structure and morphology of the WSe 2 sensing films were studied by Raman spectroscopy, photoluminescence, optical microscopy, and scanning electron microscopy (SEM) techniques. The relative humidity-dependent sensing performances of the 2D WSe 2 films were evaluated using current–voltage (I–V), relative impedance, and complex total impedance (electrochemical impedance spectroscopy, EIS) techniques. This sensor showed a very stable and repeatable performance investigated over the period of 18 months. The response and recovery times of the WSe 2 -based impedance sensors were found to be 40 and 30 s, respectively. The WSe 2 sensor exhibits a 2 ± 1% minimum hysteresis at a lower humidity level (50% RH) and around 8 ± 2% maximum hysteresis at relative humidity level (70% RH). This value of hysteresis is in the acceptable range during the initial investigation of any material to explore its potential for application in humidity sensors. The density functional theory (DFT) analysis was performed with the interaction from water molecules of the WSe 2 sample for a better understanding of the sensing mechanism of devices.

2D- WSe2↗
DOE OSTI2020

Engineering the Microstructure and Morphology of Explosive Films via Control of Interfacial Energy

Physical vapor deposition of organic explosives enables growth of polycrystalline films with a unique microstructure and morphology compared to the bulk material. This study demonstrates the ability to control crystal orientation and porosity in pentaerythritol tetranitrate films by varying the interfacial energy between the substrate and the vapor-deposited explosive. Additionally, variation in density, porosity, surface roughness, and optical properties is achieved in the explosive film, with significant implications for initiation sensitivity and detonation performance of the explosive material. Various surface science techniques, including angle-resolved X-ray photoelectron spectroscopy and multiliquid contact angle analysis, are utilized to characterize interfacial characteristics between the substrate and explosive film. Optical microscopy and scanning electron microscopy of pentaerythritol tetranitrate surfaces and fracture cross sections illustrate the difference in morphology evolution and the microstructure achieved through surface energy modification. X-ray diffraction studies with the Tilt-A-Whirl three-dimensional pole figure rendering and texture analysis software suite reveal that high surface energy substrates result in a preferred (110) out-of-plane orientation of pentaerythritol tetranitrate crystallites and denser films. Low surface energy substrates create more randomly textured pentaerythritol tetranitrate and lead to nanoscale porosity and lower density films. This work furthers the scientific basis for interfacial engineering of polycrystalline organic explosive films through control of surface energy, enabling future study of dynamic and reactive detonative phenomena at the microscale. Results of this study also have potential applications to active pharmaceutical ingredients, stimuli-responsive polymer films, organic thin film transistors, and other areas.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tailoring the Physicochemical Properties of Nb Thin Films via Surface Engineering Methods

The modification of surface oxide layers formed on niobium (Nb) thin films via chemical mechanical planarization (CMP) and accelerated neutral atom beam (ANAB) processing provides a promising route toward tailoring their emergent properties and performance when used as superconducting qubits. Here, in this study, we show that CMP- and ANAB-formed Nb oxides are significantly thinner and smoother than the native oxide, as revealed by transmission electron microscopy (TEM) and atomic force microscopy. Scanning TEM and energy-dispersive X-ray spectroscopy along with X-ray photoelectron spectroscopy identified an oxidation gradient within the native and surface-engineered oxides. The topside layer is dominated by Nb 5+ (Nb 2 O 5 ), with various Nb suboxides present closer to the oxide/metal interface. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) depth profiling confirmed the presence of an oxygen content gradient and demonstrated the enhanced resistance of the CMP- and ANAB-formed oxides to oxygen surface exchange and subsequent diffusion via 18 O 2 isotopic labeling experiments. ToF-SIMS also identified an interfacial layer containing trapped hydrogen (H)-containing species at the Nb oxide/metal interface. In situ ToF-SIMS and TEM revealed migration of the H/OH interfacial layer coinciding with decomposition of the surface oxide. Furthermore, our density functional theory calculations indicated that both H from moisture present in ambient air and bulk H in Nb films tend to segregate at the interface. These findings underscore the importance of understanding surface oxidation mechanisms, hydrogen incorporation, and their impact on the designed functionalities of Nb-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Liquid Crystal Films as Active Substrates for Nanoparticle Control

Organizing nanoparticles in a controlled way allows us to monitor their optical properties. It is particularly interesting to organize them on top of liquid crystal films to take advantage, in a second step, of the easy actuation of liquid crystals with external parameters such as temperature, electric fields, and so forth. We show that despite their fluidity, nematic and smectic films allow the formation of well-ordered hexagonal domains of gold spherical nanoparticles (AuNPs) at their surface, but we also show that both nematic films and AuNP domains impact each other. Using optical microscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), and spectrophotometry, we compare nematic, polymer-stabilized nematic, and smectic films with AuNP domains made of NPs of diameter 6 nm. On the liquid crystal films, depressions are revealed below the AuNP domains, whereas the AuNP domains appear well-organized but with a hexagonal period shortened with respect to AuNP monolayers formed on hard substrates. We interpret these features by the anchoring tilt imposed by the AuNP domains on the liquid crystal molecules. The smectic-A layers characteristic of the nematic surface transform into smecticC layers, which induce the formation of depression. Here, the energy penalty associated with the local smectic-A/smectic-C transition induces the shortening of the AuNP domain period in order to decrease the AuNP domain surface. The observed large depth of the polymer-stabilized nematic depressions below AuNP domains may be explained either by an increased size of the polymer-stabilized smectic layers close to the surface or by an increased number of polymer-stabilized smectic liquid crystal smectic layers close to the surface with respect to pure nematic films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chemical Vapor Deposition-Grown Hexagonal Boron Nitride and Graphene for Tandem Dielectric Capacitive Polymer Devices

To address the low energy density of polymeric capacitors, this work explores how tandem combinations of antagonistic properties can enhance energy storage. We introduce multilayer architecture integrating chemical vapor deposition (CVD)-grown ≈2 nm hexagonal boron nitride (hBN) and graphene with ferroelectric polyvinylidene fluoride (PVDF) and linear polyetherimide (PEI) layers to suppress leakage paths, reduce loss, and promote Maxwell–Wagner–Sillars polarization. Raman spectroscopy, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), and plasma focused ion beam (PFIB) analyses confirm robust material integration. In conclusion, for the tandem device, E BD ≈600 V/μm, while individual layers show lower values (PVDF|Graphene (Gr)|PVDF ≈ 50 V/μm and PEI|hBN|PEI ≈ 275 V/μm), yielding an overall ≈6000% enhancement and demonstrating the effectiveness of the 2D multilayer design.

Chemical vapor deposition (CVD)↗
DOE OSTI2020

Direct Visualization of Current-Stimulated Oxygen Migration in YBa 2 Cu 3 O 7–δ Thin Films

The past years have witnessed major advancements in all-electrical doping control on cuprates. In the vast majority of cases, the tuning of charge carrier density has been achieved via electric field effect by means of either a ferroelectric polarization or using a dielectric or electrolyte gating. Unfortunately, these approaches are constrained to rather thin superconducting layers and require large electric fields in order to ensure sizable carrier modulations. In this work, we focus on the investigation of oxygen doping in an extended region through current-stimulated oxygen migration in YBa 2 Cu 3 O 7–δ superconducting bridges. The underlying methodology is rather simple and avoids sophisticated nanofabrication process steps and complex electronics. Here, a patterned multiterminal transport bridge configuration allows us to electrically assess the directional counterflow of oxygen atoms and vacancies. Importantly, the emerging propagating front of current-dependent doping δ is probed in situ by optical microscopy and scanning electron microscopy. The resulting imaging techniques, together with photoinduced conductivity and Raman scattering investigations, reveal an inhomogeneous oxygen vacancy distribution with a controllable propagation speed permitting us to estimate the oxygen diffusivity. These findings provide direct evidence that the microscopic mechanism at play in electrical doping of cuprates involves diffusion of oxygen atoms with the applied current. The resulting fine control of the oxygen content would permit a systematic study of complex phase diagrams and the design of electrically addressable devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Cyclopropenylidenes as Strong Carbene Anchoring Groups on Au Surfaces

The creation of stable molecular monolayers on metallic surfaces is a fundamental challenge of surface chemistry. N-Heterocyclic carbenes (NHCs) were recently shown to form self-assembled monolayers that are significantly more stable than the traditional thiols on Au system. In this study, we theoretically and experimentally demonstrate that the smallest cyclic carbene, cyclopropenylidene, binds even more strongly than NHCs to Au surfaces without altering the surface structure. We deposit bis(diisopropylamino)cyclopropenylidene (BAC) on Au(111) using the molecular adduct BAC–CO 2 as a precursor and determine the structure, geometry, and behavior of the surface-bound molecules through high-resolution X-ray photoelectron spectroscopy, atomic force microscopy, and scanning tunneling microscopy. Our experiments are supported by density functional theory calculations of the molecular binding energy of BAC on Au(111) and its electronic structure. Our work is the first demonstration of surface modification with a stable carbene other than NHC; more broadly, it drives further exploration of various carbenes on metal surfaces.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Molecular-Level Control over Ionic Conduction and Ionic Current Direction by Designing Macrocycle-Based Ionomers

Poor ionic conductivity of the catalyst-binding, submicrometer- thick ionomer layers in energy conversion and storage devices is a huge challenge. However, ionomers are rarely designed keeping in mind the specific issues associated with nanoconfinement. Here, we designed nature-inspired ionomers (calix-2) having hollow, macrocyclic, calix[4]arene-based repeat units with precise, sub-nanometer diameter. In ≤100 nm-thick films, the in-plane proton conductivity of calix-2 was up to 8 times higher than the current benchmark ionomer Nafion at 85% relative humidity (RH), while it was 1-2 orders of magnitude higher than Nafion at 20-25% RH. Confocal laser scanning microscopy and other synthetic techniques allowed us to demonstrate the role of macrocyclic cavities in boosting the proton conductivity. The systematic self-assembly of calix-2 chains into ellipsoids in thin films was evidenced from atomic force microscopy and grazing incidence small-angle X-ray scattering measurements. Moreover, the likelihood of alignment and stacking of macrocyclic units, the presence of one-dimensional water wires across this macrocycle stacks, and thus the formation of long-range proton conduction pathways were suggested by atomistic simulations. We not only did see an unprecedented improvement in thin-film proton conductivity but also saw an improvement in proton conductivity of bulk membranes when calix-2 was added to the Nafion matrices. Nafion-calix-2 composite membranes also took advantage of the asymmetric charge distribution across calix[4]arene repeat units collectively and exhibited voltage-gating behavior. The inclusion of molecular macrocyclic cavities into the ionomer chemical structure can thus emerge as a promising design concept for highly efficient ion-conducting and ion-permselective materials for sustainable energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Enrichment of Phosphates, Lead, and Mixed Soil–Organic Particles in INPs at the Southern Great Plains Site

Ice nucleating particles (INPs) are rare particles that initiate primary ice formation, a critical step required for subsequent important cloud microphysical processes that ultimately govern cloud phase and cloud radiative properties. Laboratory studies have found that organic-rich dusts, such as those found in soils, are more efficient INPs compared to mineral dust. However, the atmospheric relevance of these organic-rich dusts are not well understood, particularly in regions with significant agricultural activity. The Agricultural Ice nuclei at the Southern Great Plains field campaign (AGINSGP) was conducted in rural Oklahoma to investigate how soil dusts contribute to INP populations in the Great Plains. We present chemical characterization of ambient and ice crystal residual particles from a single day of sampling, using single particle mass spectrometry (SPMS) and scanning microscopy. Ambient particles were primarily carbonaceous or secondary aerosol, while the fraction of dust particles was higher in the residual particles. We also observed an unusual particle type consisting of a carbonaceous core mixed with dust fragments on the surface, which was found in higher proportion in residuals. Dust particles measured during residual sampling contained greater proportions of phosphate $(^{63}\text{PO}^-_2$ and $^{79}\text{PO}^-_3)$ and lead ( 206 Pb + ). Strong sulfate signals were not seen in the residual dust particles measured by the SPMS, while nitrate was slightly depleted relative to ambient dust. This study shows that organic-rich soils may be important contributors to the ambient INP population in agricultural regions.

54 ENVIRONMENTAL SCIENCES↗