Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separated Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Flow separation in inlets at incidence angles

Wind-tunnel pressure data and flow pictures obtained for two two-dimensional inlet models have been examined to study the internal flow structure and separation at large incidence angles. The inlet models were 12-in. high (diffuser exit height) and had internal contraction ratio of 1.21 and 1.17. They were tested at low forward speeds over a wide range of throat Mach numbers (inlet mass flow rates) and angles of incidence. Characteristic features of the internal flow such as a drastic change of pressure gradient near the highlight, local separation bubbles and shock/boundary-layer interactions have been indicated and discussed. For a few specific cases, the experimental surface pressure distributions have been compared with theoretical predictions.

Jakubowski, A. K.↗
NASA NTRS1985

A three-dimensional turbulent separated flow and related mesurements

The applicability of and the limits on the applicability of 11 near wall similarity laws characterizing three-dimensional turbulent boundary layer flows were determined. A direct force sensing local wall shear stress meter was used in both pressure-driven and shear-driven three-dimensional turbulent boundary layers, together with extensive mean velocity field and wall pressure field data. This resulted in a relatively large number of graphical comparisons of the predictive ability of 10 of these 11 similarity models relative to measured data over a wide range of flow conditions. Documentation of a complex, separated three-dimensional turbulent flow as a standard test case for evaluating the predictive ability of numerical codes solving such flows is presented.

Pierce, F. J.↗
NASA NTRS1981

An experimental study of separated flow on a finite wing

The flow field associated with the formation of a mushroom shaped trailing edge stall cell on a low-aspect-ratio (AR = 4.0) wing was investigated in a series of low speed wind tunnel tests (Reynolds number based on 15.2 cm chord = 480,000). Flow field surveys of the separation bubble and wake of a partially stalled and fully stalled wing were completed using a hot-wire probe, a split-film probe, and a directional sensitive pressure probe. A new color video display technique was developed to display the flow field survey data. Photographs were obtained of surface oil flow patterns and smoke flow visualization

Winkelmann, A. E.↗
NASA NTRS1996

A Structured Grid Based Solution-Adaptive Technique for Complex Separated Flows

The objective of this work was to enhance the predictive capability of widely used computational fluid dynamic (CFD) codes through the use of solution adaptive gridding. Most problems of engineering interest involve multi-block grids and widely disparate length scales. Hence, it is desirable that the adaptive grid feature detection algorithm be developed to recognize flow structures of different type as well as differing intensity, and adequately address scaling and normalization across blocks. In order to study the accuracy and efficiency improvements due to the grid adaptation, it is necessary to quantify grid size and distribution requirements as well as computational times of non-adapted solutions. Flow fields about launch vehicles of practical interest often involve supersonic freestream conditions at angle of attack exhibiting large scale separate vortical flow, vortex-vortex and vortex-surface interactions, separated shear layers and multiple shocks of different intensity. In this work, a weight function and an associated mesh redistribution procedure is presented which detects and resolves these features without user intervention. Particular emphasis has been placed upon accurate resolution of expansion regions and boundary layers. Flow past a wedge at Mach=2.0 is used to illustrate the enhanced detection capabilities of this newly developed weight function.

Thornburg, Hugh↗
NASA NTRS1974

A study of forced flow separation in rocket nozzle

The characteristics of flow profile in a rocket nozzle during the start transient were investigated as well as possibilities of reducing the side-load thrust by sticking trip wires in the nozzle. To simplify the geometry of flow configuration around the trip wire, it was assumed that the flow is passing through square steps instead of round wires. Since a purely analytic solution is not available, a series of semiempirical solutions was proposed.

Chiou, J. N.↗
NASA NTRS2024

Direct Numerical Simulation of Smooth-Body Flow Separation Around a Ramp

Spanwise-periodic computation of a turbulent flow past a two-dimensional smooth ramp geometry is performed in the form of a direct numerical simulation. The Reynolds number based on the ramp height is about 147,000. A straight section that precedes the smooth ramp allows the incoming turbulent boundary layer to grow under a weak favorable pressure gradient. The boundary layer introduced at the domain inlet has a momentum-thickness based Reynolds number of 2000. The turbulent boundary layer nearing the ramp first interacts with a relatively stronger favorable pressure gradient, followed by a strong adverse pressure gradient. Consequently, the boundary layer experiences a modest acceleration before decelerating and separating. Analysis of the data over this region hints at the formation of an internal layer beneath the accelerated boundary layer. The analysis also reveals that this internal layer forms the origin of the free shear layer that emerges in the deceleration region and separates. The streamwise extent of the separated region is comparable to the ramp length, while the viscous layer thickness near reattachment is about the same as the ramp height; hence, the boundary layer undergoing separation and subsequent reattachment in the present configuration experiences its thickness being amplified by about tenfold. The reattached flow continues to develop further under a diminishing pressure gradient in the recovery region in a similar fashion to a zero pressure gradient turbulent boundary layer.

Turbulence↗
NASA NTRS1981

A discrete vortex method for the non-steady separated flow over an airfoil

A discrete vortex method was used to analyze the separated non-steady flow about a cambered airfoil. The foil flow modelling is based on the thin lifting-surface approach, where the chordwise location of the separation point is assumed to be known from experiments or flow-visualization data. Calculated results provided good agreement when compared with the post-stall aerodynamic data of two airfoils. Those airfoil sections differed in the extent of travel of the separation point with increasing angle of attack. Furthermore, the periodic wake shedding was analyzed and its time-dependent influence on the airfoil was investigated.

Katz, J.↗
NASA NTRS1979

Application of split-film anemometer and mini-computer for measurement in turbulent separated flow

A split-film anemometer has been adapted for measurement of highly turbulent intermittently reversing flows in regions of local separation around airfoils and flaps. Analog signals from the split-film anemometer are fed directly to a mini-computer for processing and analysis. Mean velocity magnitude and direction, intermittency of reversal, turbulence intensity and histograms of the velocity are obtained as outputs of the system.

Wentz, W. H.↗
NASA NTRS1986

The computation of steady 3-D separated flows over aerodynamic bodies at incidence and yaw

This paper describes the implementation of a general purpose 3-D NS code and its application to simulated 3-D separated vortical flows over aerodynamic bodies. The thin-layer Reynolds-averaged NS equations are solved by an implicit approximate factorization scheme. The pencil data structure enables the code to run on very fine grids using only limited incore memories. Solutions of a low subsonic flow over an inclined ellipsoid are compared with experimental data to validate the code. Transonic flows over a yawed elliptical wing at incidence are computed and separations occurred at different yaw angles are discussed.

Pulliam, T. H.↗
NASA NTRS1981

The challenge of unsteady separating flows

It is noted that the general fluid dynamic problem of unsteady separation at most practical Reynolds numbers remains an unsolved one and that no completely reliable prediction techniques exist at the present time. The modern design engineer must therefore draw from a combination of approximate theories, empirical correlations of data, and finite difference programs based on uncertain physical modeling of turbulence. An attempt is made to describe the basic features of several representative classes of problems for which unsteady effects produce strong or unusual changes in the separation characteristics of the flow. The analysis concerns itself largely with external flow, and emphasis is placed on the physical phenomena involved.

Mccroskey, W. J.↗
NASA NTRS2024

Turbulence Model Validation through Joint Experimental / Computational Studies of Separated Flow Over a Three-Dimensional Tapered Bump: Part II - Computational Investigation

This report serves as documentation of activities related to Computational Fluid Dynamics (CFD) analysis applied to the Smooth Body Separation Experiment designed to produce validation-quality experimental data from wind-tunnel tests performed at the University of Notre Dame. All CFD analysis utilized the Boeing CFD (BCFD) flow solver. BCFD was used to analyze flow over the Boeing Speed Bump with second-order accuracy in space and time. Inviscid fluxes were computed using the HLLE scheme for steady-state simulations, and the Low-Dissipation Roe scheme for time-accurate simulations. The working fluid was modeled as calorically perfect air using Sutherland's law for viscosity. Thermal diffusivity was determined by assuming a constant molecular Prandtl number of 0.72, and a turbulent Prandtl number of 0.9. Reynolds Averaged Navier-Stokes (RANS) simulations were conducted using the one-equation Spalart-Allmaras turbulence model with rotation correction3 and the quadratic constitutive relation (SA-RC-QCR), as well as Menter's two-equation, Shear-Stress Transport (SST) model. Time-accurate computations were conducted using Delayed Detached eddy Simulation (DDES) with the one-equation RANS model, and Large Eddy Stress balance (LESb) with the two-equation RANS model. Implicit dual-time stepping was used to achieve second-order temporal accuracy. The experimental investigation conducted during the course of this study is described in detail in an accompanying report.

Flow separation↗
NASA NTRS1982

Evolution of shock-induced pressure on a flat-face/flat-base body and afterbody flow separation

The time-dependent, compressible Reynolds-averaged, Navier-Stokes equations are applied to solve an axisymmetric supersonic flow around a flat-face/flat-base body with and without a sting support. Important transient phenomena, not yet well understood, are investigated, and the significance of the present solution to the phenomena is discussed. The phenomena, described in detail, are as follows: the transient formation of the bow and recompression shock waves; the evolution of a pressure buildup due to diffraction of the incident shock wave in the forebody and afterbody regions, including the luminosity accompanying the pressure buildup; the separation of the flow as influenced by pressure buildup; the location of the separation and the reattachment points; and the transient period of the shock-induced base flow. The important influence of the nonsteady (transient) and steady flow on the aerodynamic characteristics, radiative heat transfer, and, thus, on the survivability or safeguard problems for an aircraft fuselage, missile, or planetary entry probe at very high flight speeds is described.

Yoshikawa, K. K.↗
NASA NTRS1978

Effect of flow separation vortices on aircraft unsteady aerodynamics

The unsteady aerodynamic flow field over the space shuttle orbiter was studied. The results indicate at moderate to high angles of attack separation-induced vortices exact a dominating influence on the unsteady aerodynamics of the space shuttle orbiter and of high performance aircraft. The main characteristics are as follows: (1) The vortex-induced aerodynamic loads are large and highly nonlinear, sometimes discontinuous in character; and (2) the vortex-induced loads have opposite effects on static and dynamic stability characteristics. Analytic approximations are presented which can predict these vortex-induced aerodynamic effects with the accuracy needed for most engineering design.

Ericsson, L. E.↗
NASA NTRS1949

Experimental Study of Gas-Flow Separation in Overexpanded Exhaust Nozzles for Rocket Motors

In a rocket motor having a de Laval nozzle with a fixed expansion ratio, there is only one pressure ratio (p(sub c)/p(sub o)) for which this expansion ratio is correct. At any other pressure ratio the gases will be either underexpanded or overexpanded, depending on whether the pressure ratio is higher or lower than the correct value. Rocket motor flame patterns illustrating the four possible regimes are shown in Figures 1 to 4, inclusive. In Figure 1, the pressure ratio is higher than the correct one for the fixed expansion ratio of the nozzle, resulting in underexpansion of the gases. in Figure 2, the pressure ratio is the correct one. In Figure 3, the pressure ratio is only slightly lower than the correct one, resulting in overexpansion without separation of the gases from the wall. In Figure 4, the pressure ratio is considerably below the correct one, resulting in overexpansion with separation of the gases from the nozzle wall. The present report is concerned primarily with this fourth type of flow, that is, overexpansion of the gases with separation of the flow from the wall. Such a situation exists in a rocket motor operating at a considerably lower altitude than that for which its exhaust nozzle was designed.

Cowles, Frederick B.↗
NASA NTRS1984

Feedback in separated flows over symmetric airfoils

For a flow over an airfoil with laminar separation, a feedback cycle may exist whereby a Kelvin-Helmholtz instability wave emanating from the separation point on the airfoil surface grows along the shear layer and is diffracted as it interacts with the sharp trailing edge of the airfoil, causing acoustic radiation which, in turn, propagates upstream and regenerates the initial instability wave. The analysis is restricted to the high frequency limit. Solutions to the boundary-value problem are obtained using the slowly varying approximation and the method of matched asymptotic expansions. Resonant solutions exist for certain discrete values of the Reynolds and Strouhal numbers. The results are discussed and compared with available data.

Atassi, H. M.↗
NASA NTRS1984

Feedback in separated flows over symmetric airfoils

For a flow over an airfoil with laminar separation, a feedback cycle may exist whereby a Kelvin-Helmholtz instability wave emanating from the separation point on the airfoil surface grows along the shear layer and is diffracted as it interacts with the sharp trailing edge of the airfoil, causing acoustic radiation which , in turn, propagates upstream and regenerates the initial instability wave. The analysis is restricted to the high frequency limit. Solutions to the boundary-value problem are obtained using the slowly varying approximation and the method of matched asymptotic expansions. Resonant solutions exist for certain discrete values of the Reynolds and Strouhal numbers. The results are discussed and compared with available data.

Atassi, H. M.↗