SEARCH · Search NASA

Results for “Shape selectivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1960

Evaluation of Blended Wing-Body Combinations with Curved Plan Forms at Mach Numbers Up to 3.50

This investigation is a continuation of the experimental and theoretical evaluation of the effects of wing plan-form variations on the aerodynamic performance characteristics of blended wing-body combinations. The present report compares previously tested straight-edged delta and arrow models which have leading-edge sweeps of 59.04 and 70-82 deg., respectively, with related models which have plan forms with curved leading and trailing edges designed to result in the same average sweeps in each case. All the models were symmetrical, without camber, and were generally similar having the same span, length, and aspect ratios. The wing sections had an average value of maximum thickness ratio of about 4 percent of the local wing chords in a streamwise direction. The wing sections were computed by varying their shapes along with the body radii (blending process) to match the selected area distribution and the given plan form. The models were tested with transition fixed at Reynolds numbers of roughly 4,000,000 to 9,000,000, based on the mean aerodynamic chord of the wing. The characteristic effect of the wing curvature of the delta and arrow models was an increase at subsonic and transonic speeds in the lift-curve slopes which was partially reflected in increased maximum lift-drag ratios. Curved edges were not evaluated on a diamond plan form because a preliminary investigation indicated that the curvature considered would increase the supersonic zero-lift wave drag. However, after the test program was completed, a suitable modification for the diamond plan form was discovered. The analysis presented in the appendix indicates that large reductions in the zero-lift wave drag would be obtained at supersonic Mach numbers if the leading- and trailing-edge sweeps are made to differ by indenting the trailing edge and extending the root of the leading edge.

Holdaway, George H.↗

NASA NTRS1959

Investigation at Mach Numbers of 0.20 to 3.50 of a Blended Diamond Wing and Body Combination of Sonic Design but with Low Wave-Drag Increase with Increasing Mach Number

A diamond wing and body combination was designed to have an area distribution which would result in near optimum zero-lift wave-drag coefficients at a Mach number of 1.00, and decreasing wave-drag coefficient with increasing Mach number up to near sonic leading-edge conditions for the wing. The airfoil section were computed by varying their shape along with the body radii (blending process) to match the selected area distribution and the given plan form. The exposed wing section had an average maximum thickness of about 3 percent of the local chords, and the maximum thickness of the center-line chord was 5.49 percent. The wing had an aspect ratio of 2 and a leading-edge sweep of 45 deg. Test data were obtained throughout the Mach number range from 0.20 to 3.50 at Reynolds numbers based on the mean aerodynamic chord of roughly 6,000,000 to 9,000,000. The zero-lift wave-drag coefficients of the diamond model satisfied the design objectives and were equal to the low values for the Mach number 1.00 equivalent body up to the limit of the transonic tests. From the peak drag coefficient near M = 1.00 there was a gradual decrease in wave-drag coefficient up to M = 1.20. Above sonic leading-edge conditions of the wing there was a rise in the wave-drag coefficient which was attributed in part to the body contouring as well as to the wing geometry. The diamond model had good lift characteristics, in spite of the prediction from low-aspect-ratio theory that the rear half of the diamond wing would carry little lift. The experimental lift-curve slope obtained at supersonic speeds were equal to or greater than the values predicted by linear theory. Similarly the other basic aerodynamic parameters, aerodynamic center position, and maximum lift-drag ratios were satisfactorily predicted at supersonic speeds.

Holdaway, George H.↗

NASA NTRS2004

Numerical Modeling of the South Pole-Aitkin Impact

The South Pole-Aitkin (SPA) basin, on the far side of the Moon, is the largest and oldest impact structure still preserved in the solar system. The crater is about 2500 km in diameter and formed in the Pre-Nectarian era of lunar history, over 4 Gyr ago. At this time, the thermal state of the Moon was much hotter than it is today. Accretional energy from the rapidly forming Moon melted the outermost few hundred kilometers of the Moon. As this magma ocean differentiated and cooled a 60 100-km thick low-density crust formed at the surface; below this the residual melt, with a higher density, cooled to form the lunar mantle. The giant SPA impact event punctured the Moon some time during the cooling of the magma ocean and thus provides a unique window for studying the lunar interior and the early formative processes of the Moon. The impact excavated otherwise inaccessible samples of the deep crust and (possibly) upper mantle, which has inspired proposed sample return missions. Furthermore, the thermal and rheologic state of the early Moon played a role in shaping the final structure of the basin. To aid in site selection for future sample return missions to the SPA basin, and to investigate the effect of thermal state on final crater structure, we performed some numerical simulations of the SPA impact event.

Collins, G. S.↗

NASA NTRS2014

Design and Development of Aerogel-Based Antennas for Aerospace Applications: A Final Report to the NARI Seedling

As highly porous solids possessing low density and low dielectric permittivity combined with good mechanical properties, polyimide (PI) aerogels offer great promise as an enabling technology for lightweight aircraft antenna systems. While they have been aggressively explored for thermal insulation, barely any effort has been made to leverage these materials for antennas or other applications that take advantage of their aforementioned attributes. In Phase I of the NARI Seedling Project, we fabricated PI aerogels with properties tailored to enable new antenna concepts with performance characteristics (wide bandwidth and high gain) and material properties (low density, environmental stability, and robustness) superior to the state of practice (SOP). We characterized electromagnetic properties, including permittivity, reflectivity, and propagation losses for the aerogels. Simple, prototype planar printed circuit patch antennas from down-selected aerogel formulations were fabricated by molding the aerogels to net shapes and by gold-metalizing the pattern onto the templates via electron beam evaporation in a clean room environment. These aerogel based antennas were benchmarked against current antenna SOP, and exhibited both broader bandwidth and comparable or higher gain performance at appreciably lower mass. Phase II focused on the success of the Phase I results pushing the PI aerogel based antenna technology further by exploring alternative antenna design (i.e., slot coupled antennas) and by examining other techniques for fabricating the antennas including ink jet printing with the goal of optimizing antenna performance and simplifying production. We also examined new aerogel formulations with better moisture and solvent resistance to survive processing conditions. In addition, we investigated more complex antenna designs including passive phased arrays such as 2x4 and 4x8 element arrays to assess the scalability of the aerogel antenna concept. Furthermore, we explored the possibility of developing these arrays in thin, flexible form to make conformable antennas.

insulation↗

NASA NTRS2011

Focused and Steady-State Characteristics of Shaped Sonic Boom Signatures: Prediction and Analysis

The objective of this study is to examine the effect of flight, at off-design conditions, on the propagated sonic boom pressure signatures of a small "low-boom" supersonic aircraft. The amplification, or focusing, of the low magnitude "shaped" signatures produced by maneuvers such as the accelerations from transonic to supersonic speeds, climbs, turns, pull-up and pushovers is the concern. To analyze these effects, new and/or improved theoretical tools have been developed, in addition to the use of existing methodology. Several shaped signatures are considered in the application of these tools to the study of selected maneuvers and off-design conditions. The results of these applications are reported in this paper as well as the details of the new analytical tools. Finally, the magnitude of the focused boom problem for "low boom" supersonic aircraft designs has been more accurately quantified and potential "mitigations" suggested. In general, "shaped boom" signatures, designed for cruise flight, such as asymmetric and symmetric flat-top and initial-shock ramp waveforms retain their basic shape during transition flight. Complex and asymmetric and symmetric initial shock ramp waveforms provide lower magnitude focus boom levels than N-waves or asymmetric and symmetric flat-top signatures.

Maglieri, Domenic J.↗

NASA NTRS1995

Probability Density Functions of Observed Rainfall in Montana

The question of whether a rain rate probability density function (PDF) can vary uniformly between precipitation events is examined. Image analysis on large samples of radar echoes is possible because of advances in technology. The data provided by such an analysis easily allow development of radar reflectivity factors (and by extension rain rate) distribution. Finding a PDF becomes a matter of finding a function that describes the curve approximating the resulting distributions. Ideally, one PDF would exist for all cases; or many PDF's that have the same functional form with only systematic variations in parameters (such as size or shape) exist. Satisfying either of theses cases will, validate the theoretical basis of the Area Time Integral (ATI). Using the method of moments and Elderton's curve selection criteria, the Pearson Type 1 equation was identified as a potential fit for 89 percent of the observed distributions. Further analysis indicates that the Type 1 curve does approximate the shape of the distributions but quantitatively does not produce a great fit. Using the method of moments and Elderton's curve selection criteria, the Pearson Type 1 equation was identified as a potential fit for 89% of the observed distributions. Further analysis indicates that the Type 1 curve does approximate the shape of the distributions but quantitatively does not produce a great fit.

Larsen, Scott D.↗

NASA NTRS1989

Continuum energy distribution of quasars - Shapes and origins

Continuum observations from 0.3 nm to 6 cm are presented for 109 optically selected quasars from the Palomar-Green (PG) Bright Quasar Survey. The far-infrared to soft X-ray continuum of radio-quiet and steep-spectrum radio-loud PG quasars can be described in a model consisting of two broad peaks: an 'infrared bump' at about 2 microns to 1 mm and the well-known 'big blue bump' at about 10 nm to 0.3 micron. All PG quasars emit a significant fraction of their bolometric luminosity at infrared wavelengths of 1.5-100 microns. The fraction varies from 10 to 50 percent with a typical value of 30 percent. The ratio of the 6 cm flux density to that at 1 micron has a bimodal distribution. There is no evidence for a tight correlation between the infrared and X-ray continua of quasars. It is suggested that the bulk of the emission between 2 microns and 1 mm in the infrared bump of the radio-quiet PG quasars and the radio-loud quasars with steep radio spectral indices is produced by thermal processes.

Sanders, D. B.↗

NASA NTRS1994

Active vibration damping using smart material

We consider the modeling and active damping of an elastic beam using distributed actuators and sensors. The piezoelectric ceramic material (PZT) is used to build the actuator. The sensor is made of the piezoelectric polymer polyvinylidene fluoride (PVDF). These materials are glued on both sides of the beam. For the simple clamped beam, the closed loop controller has been shown to be able to extract energy from the beam. The shape of the actuator and its influence on the closed loop system performance are discussed. It is shown that it is possible to suppress the selected mode by choosing the appropriate actuator layout. It is also shown that by properly installing the sensor and determining the sensor shape we can further extract and manipulate the sensor signal for our control need.

Baras, John S.↗

NASA NTRS1966

Swiveling Lathe Jaw Concept for Holding Irregular Pieces

Clamp holds irregularly shaped pieces in lathe chuck without damage and eliminates excessive time in selecting optimum mounting. Interchangeable jaws ride in standard jaw slots but swivel so that the jaw face bears evenly against the workpiece regardless of contour. The jaws can be used on both engine and turret lathes.

David, J.↗

NASA NTRS1966

Special mandrel permits uniform welding of out-of-round tubing

Dor, M. E.↗

NASA NTRS1972

Chemical nonequilibrium effects on the flow in the windward plane of symmetry of a blunted delta orbiter

The extent, and some of the consequences, of nonequilibrium effects in the inviscid orbiter flow field are examined. Calculations have been made for the reacting flow along selected streamlines in the windward plane of symmetry of a blunted delta shape representative of a shuttle orbiter. An approximate model of the pressure field in the windward plane of symmetry of a blunted delta wing was constructed from wind tunnel measurements of the body surface pressure distribution and approximate calculations of the shock shape and streamline locations. Numerical solutions for the flow along streamlines were obtained for this pressure distribution, and solutions were obtained for both equilibrium and finite-reaction rate, nonequilibrium chemical reactions. Since the streamtube solutions are much easier to compute than fully three-dimensional, reacting flows, results were obtained for a wide range of conditions. The validity of this approach is based on the assumptions that the pressure field is insensitive to nonequilibrium effects and that the flow along streamlines is quasi-one dimensional. Numerical solutions have been used to verify this approach for other blunted slender shapes such as spherically blunted cones.

Lordi, J. A.↗

NASA NTRS1976

Methods for comparative evaluation of propulsion system designs for supersonic aircraft

The propulsion system comparative evaluation study was conducted to define a rapid, approximate method for evaluating the effects of propulsion system changes for an advanced supersonic cruise airplane, and to verify the approximate method by comparing its mission performance results with those from a more detailed analysis. A table look up computer program was developed to determine nacelle drag increments for a range of parametric nacelle shapes and sizes. Aircraft sensitivities to propulsion parameters were defined. Nacelle shapes, installed weights, and installed performance was determined for four study engines selected from the NASA supersonic cruise aircraft research (SCAR) engine studies program. Both rapid evaluation method (using sensitivities) and traditional preliminary design methods were then used to assess the four engines. The method was found to compare well with the more detailed analyses.

Tyson, R. M.↗

NASA NTRS1978

Eigenvalue/eigenvector assignment using output feedback

The problem of pole-assignment in a linear time-invariant multivariable system using output feedback is considered. New sufficient conditions are derived to assign an almost arbitrary set of min (n, m+r-1) distinct eigenvalues, where n, m, and r are the number of states, inputs, and outputs, respectively. The analysis also highlights the freedom in selection of closed-loop eigenvectors which can be used for response shaping.

Srinathkumar, S.↗

NASA NTRS1978

Strake-wing analysis and design

The technology is still evolving for improving the transonic maneuver capability of strake-wing configurations. Much of the work to date has been of an experimental nature; whereas, the theories that are available to handle vortex-flow aerodynamics have mostly treated wings of constant sweep. Hence, two efforts were undertaken. They are: (1) to extend the suction analogy to more general configurations and evaluate the method by using selected critical planforms; and (2) to develop a procedure for strake planform shaping and test the resulting shape in conjunction with a wing-body. The conclusions from this study are that (1) some improvement has been made in estimating high-angle-of-attack longitudinal aerodynamics, and (2) the gothic strake designed with the developed procedure does produce a stable vortex system in the presence of a wing body and flat post-maximum-lift characteristics.

Lamar, J. E.↗

NASA NTRS1980

Preparation of monotectic alloys having a controlled microstructure by directional solidification under dopant-induced interface breakdown

Monotectic alloys having aligned spherical particles of rods of the minor component dispersed in a matrix of the major component are prepared by forming a melt containing predetermined amounts of the major and minor components of a chosen monotectic system, providing in the melt a dopant capable of breaking down the liquid solid interface for the chosen alloy, and directionally solidfying the melt at a selected temperature gradient and a selected rate of movement of the liquid-solid interface (growth rate). Shaping of the minor component into spheres or rods and the spacing between them are controlled by the amount of dopant and the temperature gradient and growth rate values. Specific alloy systems include Al Bi, Al Pb and Zn Bi, using a transition element such as iron.

Parr, R. A.↗

NASA NTRS1981

Integrated residential photovoltaic array development

Sixteen conceptual designs of residential photovoltaic arrays are described. Each design concept was evaluated by an industry advisory panel using a comprehensive set of technical, economic and institutional criteria. Key electrical and mechanical concerns that effect further array subsystem development are also discussed. Three integrated array design concepts were selected by the advisory panel for further optimization and development. From these concepts a single one will be selected for detailed analysis and prototype fabrication. The three concepts selected are: (1) An array of frameless panels/modules sealed in a T shaped zipper locking neoprene gasket grid pressure fitted into an extruded aluminum channel grid fastened across the rafters. (2) An array of frameless modules pressure fitted in a series of zipper locking EPDM rubber extrusions adhesively bonded to the roof. Series string voltage is developed using a set of integral tongue connectors and positioning blocks. (3) An array of frameless modules sealed by a silicone adhesive in a prefabricated grid of rigid tape and sheet metal attached to the roof.

Royal, G. C., III↗

NASA NTRS1982

Seasat wind and wave observations of northeast Pacific hurricane Iva, August 13, 1978

The paper examines Seasat wind and wave observations collected in the eye of hurricane Iva on August 13, 1978 in the northeast Pacific. A maximum wind speed of 25-30 m/s is observed, along with a banana-shape high-wind-speed distribution. Two-dimensional Fourier transforms of selected SAR scenes show a dominant wavefield characterized by wavelengths of 166-211 m, with a fanlike distribution of propagation directions. A simple geometric model is proposed to explain the dominant wave field in terms of prior storm intensity and location, which is combined with the Ross parametric hurricane wave model and Seasat wind and wave data to estimate a value of 43 km for the effective radial distance from the storm center to the region of maximum winds.

Gonzalez, F. I.↗

NASA NTRS1984

Development of selected advanced aerodynamics and active control concepts for commercial transport aircraft

Work done under the Energy Efficient Transport project in the field of advanced aerodynamics and active controls is summarized. The project task selections focused on the following: the investigation of long-duct nacelle shape variation on interference drag; the investigation of the adequacy of a simple control law for the elastic modes of a wing; the development of the aerodynamic technology at cruise and low speed of high-aspect-ratio supercritical wings of high performance; and the development of winglets for a second-generation jet transport. All the tasks involved analysis and substantial wind tunnel testing. The winglet program also included flight evaluation. It is considered that the technology base has been built for the application of high-aspect-ratio supercritical wings and for the use of winglets on second-generation transports.

Taylor, A. B.↗