Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simplifications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

258 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Process Intensification for Recovery of Uranium from Spent Fuel Using DEHiBA

Two approaches are being pursued to intensify the DEHiBA process for recovery of U from used nuclear fuel. For the traditional solvent extraction approach in which the fuel is first dissolved in hot nitric acid, the DEHiBA concentration was adjusted to 1.5 M. This allows for increased loading in the organic phase, but the organic phase U concentration should remain below 100 g/L to avoid unfavorable physicochemical properties that would upset the hydrodynamics in contacting equipment such as centrifugal contactors. Direct extraction of U into the 1.5 M DHEiBA solvent is another intriguing approach to intensifying the process. In this case, the hot nitric acid dissolution step is avoided, a potential significant simplification of the process. Strategies for routing Tc, Np, and Pu to the HLW stream will likely need to be developed to avoid contamination of the U product with these undesirable species.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Neutron-induced capture-to-fission cross section ratio measured at LANSCE

Capture-to-fission cross section ratios are used as an alternative to absolute cross section measurements. This is due to the simplification on the calculations and the reduction of the uncertainties with respect to an absolute measurement of the cross section by eliminating experimental complications like self-absorption, beam/target overlap and non-uniformities. Different capture-to-fission reactions have been measured through the years at the Los Alamos Neutron Science Center (LANSCE) at Los Alamos National Laboratory (LANL) using the Detector for Advanced Neutron Capture Experiments (DANCE) combined with different fission detectors. Some of these are a Parallel Plate Avalanche Counter (PPAC) to detect fission fragments (FF), and the NEUtron detector array at DANCE (NEUANCE) to detect fission neutrons. As DANCE detects the γ-rays produced in capture and fission reactions, the fission instrument placed inside the DANCE cavity is used to tag the fission γ-rays for background identification and subtraction. Some examples of capture-to-fission ratio measurements performed with DANCE in the last years are the 233 U, 235 U and 239 Pu. The measurement technique, the different setups, and other potential applications of the instruments will be explained.

Nuclear Criticality Safety Program (NCSP)↗
DOE OSTI2025

Understanding Model Inadequacy in TRISO Nuclear Fuel Fission Products Release Models: Empirical and Mechanistic Approaches

The increasing use of tristructural isotropic (TRISO) particle fuel in both advanced and existing reactors necessitates a thorough evaluation of uncertainties and shortcomings in TRISO fission product release models. These inadequacies arise from the simplifications made in computational models compared to experimental data. Utilizing the BISON fuel performance code and experimental data from the Advanced Gas Reactor (AGR) program provides a unique chance to rigorously assess these inadequacies within a Bayesian uncertainty quantification (UQ) framework. This study contrasts the standard Bayesian framework with the Kennedy-O'Hagan (KOH) framework, which explicitly accounts for modeling inadequacies, in the context of UQ for TRISO silver release models. It examines both the traditional Arrhenius equation and a more advanced lower-length-scale (LLS)-informed model that incorporates microstructure information. The inverse UQ process applied to AGR-2 and AGR-3/4 datasets identified modeling inadequacy as the primary source of uncertainty, with experimental noise also being significant, while model parameter uncertainty was minimal. Both the Arrhenius and LLS-informed models showed similar levels of modeling inadequacy. For forward predictive UQ using the AGR-1 dataset, the KOH framework enhanced the accuracy and quality of quantified uncertainties by approximately 30% and 40%, respectively, compared to the standard Bayesian framework. This improvement was observed for both the Arrhenius and LLS-informed models. At the engineering scale, both models performed similarly, but the LLS-informed model outperformed the Arrhenius equation at the mesoscale. These findings underscore the importance of explicitly considering modeling inadequacy in the UQ process and highlight the need for ongoing refinement of physics-based models to address these shortcomings.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Multi-Scale Thermal Analysis for Design of SiC-Based Medium Voltage Motor Drive: Preprint

This paper describes a multi-scale thermal analysis approach for the design of an air-cooled 1.7-kV SiC MOSFET-based medium-voltage variable-speed motor drive. The National Renewable Energy Laboratory supported the project objectives by providing thermal management design support to the project partner The Ohio State University (OSU). The scope of the models and limited resources required efficient and flexible thermal models to be developed. Two modeling techniques are described that significantly reduced model run time and enabled more complex models to be run faster while retaining needed accuracy. The first technique uses the effectiveness-NTU method to extract convection boundary conditions from a computational fluid dynamics (CFD) model that can be applied to a fast-running finite element analysis model. The second is a porous media technique that enables system-level CFD simulations that incorporate effects from heat exchangers (e.g., pin fin heat sinks) that run in a fraction of the time required for fully resolved CFD simulations. The multi-scale approach to the thermal analysis enabled fast and accurate simulation for the converter design ranging from the die level up to the full system with 36 submodules. The modeling results were validated against experimental data from system tests performed by OSU.

DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Simplifying the Advanced Test Reactor LOWE Element Test Series

The Advanced Test Reactor (ATR) is one of six remaining high performance research reactors in the United States scheduled to be converted from 93% high-enriched uranium (HEU) fuel to 19.75% low-enriched uranium (LEU) fuel as part of the Department of Energy (DOE), National Nuclear Security Administration (NNSA), Office of Material Management and Minimization (MMM) reactor conversion efforts(1). The specific LEU fuel element design for the ATR is called the Low Enriched (LOWE) element. A series of fuel qualification tests are scheduled to occur over the next decade before the ATR is fully converted. In addition to several experiments of demonstration plates, a series of Element Tests (ETs) are planned for conversion, in which full sized LOWE elements are placed in ATR driver positions. The purpose of these ETs was generally to sequentially increase the amount of LEU and core power to full power, therefore creating a representative safety profile in which LEU could operate for the duration of the ATR lifetime. The planned element tests were (2): ET-1: one LOWE element at low power for once cycle ET-2: ~8 LOWE elements at low/medium power for multiple cycles, and ET-3: >8 LOWE elements for a full lobe of elements at high power for multiple cycles. Given recent improvements in modeling fidelity, scheduling considerations, and an opportunity to combine later ETs, the LEU conversion program successfully defined the operational requirements for the “ET-ATR” test, which combines the needed information collected from ET-2 and ET-3 into a single test.

42 ENGINEERING↗