Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Comparative radiation resistance, temperature dependence and performance of diffused junction indium phosphide solar cells

Indium phosphide solar cells whose p-n junctions were processed by the open tube capped diffusion and by the closed tube uncapped diffusion of sulfur into Czochralski-grown p-type substrates are compared. Differences found in radiation resistance were attributed to the effects of increased base dopant concentration. Both sets of cells showed superior radiation resistance to that of gallium arsenide cells, in agreement with previous results. No correlation was, however, found between the open-circuit voltage and the temperature dependence of the maximum power.

Weinberg, I.↗
NASA NTRS1989

InP shallow-homojunction solar cells

Indium phosphide solar cells with very thin n-type emitters have been made by both ion implantation and metalorganic chemical vapor deposition. Air mass zero efficiencies as high as 18.8 percent (NASA measurement) have been achieved. Although calculations show that, as is the case with GaAs, a heterostructure is expected to be required for the highest efficiencies attainable, the material properties of InP give the shallow-homojunction structure a greater potential than in the case of GaAs. The best cells, which were those made by ion implantation, show open-circuit voltage (V sub oc) of 873 mV, short-circuit current of 357 A/sq m (35.7 mA/sq cm), and fill factor of 0.829. Improvements are anticipated in all three of these parameters. Internal quantum efficiency peaks at over 90 percent in the red end of the spectrum, but drops to 54 percent in the blue end. Other cells have achieved 74 percent in the blue end. Detailed modeling of the data indicates that a high front surface recombination velocity is responsible for the low blue response, that the carrier lifetime is high enough to allow good carrier collection from both the base and the emitter, and that the voltage is base-limited.

Keavney, Christopher↗
NASA NTRS1993

Radiation effects in heteroepitaxial InP solar cells

Heteroepitaxial InP solar cells, with GaAs substrates, were irradiated by 0.5 and 3 MeV protons and their performance, temperature dependency, and carrier removal rates determined as a function of fluence. The radiation resistance of the present cells was significantly greater than that of non-heteroepitaxial InP cells at both proton energies. A clear difference in the temperature dependency of V(sub oc), was observed between heteroepitaxial and homoepitaxial InP cells. The analytically predicted dependence of dV(sub oc)/dT on Voc was confirmed by the fluence dependence of these quantities. Carrier removal was observed to increase with decreasing proton energy. The results obtained for performance and temperature dependency were attributed to the high dislocation densities present in the heteroepitaxial cells while the energy dependence of carrier removal was attributed to the energy dependence of proton range.

Weinberg, I.↗
NASA NTRS1981

Metallization for large-area solar cells

In large area, low cost solar cells of any type, the contact and grid structure metallization is an important factor which has an effect on the efficiency of the solar cell and its reliability. The present investigation is concerned with aspects of solar cell efficiency. An optimized metallization design leads to minimum total power loss, which is related to a simultaneous minimization of ohmic voltage drops and of shading of the front surface of the cell by the overlaid metal. The requirements regarding the design for a low-loss metallization pattern for the front surface of large area solar cells are represented by a set of design rules listed in a table. The total shading and voltage drop on such cells can be held to about 5%. However, not every metallization process is suited for meeting the requirements of the low-cost design. The low losses can be achieved only by use of several bus lines containing a bulk conductor, such as a wire.

Wolf, M.↗
DOE OSTI2024

Comprehensive Study of Carrier Recombination in High‐Efficiency CdTe Solar Cells Using Transient Photovoltage

Cadmium telluride (CdTe) solar cells represent a commercially successful photovoltaic technology, with an annual production capacity approaching 20 GW. However, improving the open-circuit voltage (V OC ) remains challenging. This study aims to deepen the understanding of charge carrier recombination in CdTe solar cells and to explore alternative dynamical characterization methods that address the limitations found in conventionally used time-resolved photoluminescence for CdTe solar cells. Transient photovoltage and transient photocurrent techniques are utilized to investigate charge carrier dynamics under conditions resembling real-world solar cell operation. The results reveal that an effective nonradiative recombination lifetime of 580 ns dominates the charge dynamics at VOC values below 850 mV. Above this threshold, radiative recombination becomes significant, with a radiative recombination coefficient of 1.1 × 10 −9 cm 3 s −1 . Additionally, the stationary charge carrier density at 1 sun is determined to be around 1 × 10 14 cm −3 . By accurately determining both radiative and nonradiative recombination, this work provides a comprehensive understanding of carrier dynamics in high-performing CdTe devices and paves the way for improving the V OC and performance of CdTe solar cells.

CdTe solar cells↗
DOE OSTI2025

Laser Ablation for Low-Cost Multijunction III-V Solar Cell Mesa Isolations

Eliminating photolithography from solar cell processing is a significant opportunity for cost reduction for III-V solar cells. In this work, we test femtosecond laser ablation and scribing as an alternative to contact photolithography and wet chemical etching for mesa isolation, when processing multijunction cells. We demonstrate that upright multijunction solar cells isolated by using the laser as a scribe to cleave through the substrate had virtually no performance loss when compared to a baseline cell processed with photolithography. By contrast, cells isolated by laser ablating through the active layers have performance losses that cannot be fully eliminated with post-processing etches. This demonstration of photolithography-free mesa isolation with no performance losses is promising for less expensive III-V manufacturing.

14 SOLAR ENERGY↗
NASA NTRS1975

Effects of processing on the carrier lifetime in silicon solar cells

Measurements were taken to determine the effects that solar cell processing steps have on the minority carrier lifetime in silicon. The experimental work included measurements of diffusion lengths of the silicon at various stages of cell fabrication, of solar cell properties, and of the PN junction properties for ingots covering a wide range of doping and other ingot properties. Resistivities covered the range of 0.01 to 10 ohm-cm, and combinations of extreme concentrations (high and low) of dislocations and oxygen were included. The results showed that the major cell process steps did not usually cause any appreciable change in diffusion lengths. The solar cell currents obtained supported the diffusion length measurements. The effects of heavy doping concentrations on solar cell performance were studied. Attempts were made to relate the voltage behavior of the cells with the diode properties and the properties of the ingots.

Iles, P. A.↗
NASA NTRS1995

Results of the 1995 JPL balloon flight solar cell calibration program

The Jet Propulsion Laboratory (JPL) solar cell calibration program was conceived to produce reference standards for the purpose of accurately setting solar simulator intensities. The concept was to fly solar cells on a high-altitude balloon, to measure their output at altitudes near 120,000 ft (36.6 km), to recover the cells, and to use them as reference standards. The procedure is simple. The reference cell is placed in the simulator beam, and the beam intensity is adjusted until the reference cell reads the same as it read on the balloon. As long as the reference cell has the same spectral response as the cells or panels to be measured, this is a very accurate method of setting the intensity. But as solar cell technology changes, the spectral response of the solar cells changes also, and reference standards using the new technology must be built and calibrated. Until the summer of 1985, there had always been a question as to how much the atmosphere above the balloon modified the solar spectrum. If the modification was significant, the reference cells might not have the required accuracy. Solar cells made in recent years have increasingly higher blue responses, and if the atmosphere has any effect at all, it would be expected to modify the calibration of these newer blue cells much more so than for cells made in the past. JPL has been flying calibration standards on high-altitude balloons since 1963 and continues to organize a calibration balloon flight at least once a year. The 1995 flight was the 48th flight in this series. The 1995 flight incorporated 46 solar cell modules from 7 different participants. The payload included Si, amorphous Si, GaAs, GaAs/Ge, dual junction cells, top and bottom sections of dual junction cells, and a triple junction cell. A new data acquisition system was built for the balloon flights and flown for the first time on the 1995 flight. This system allows the measurement of current-voltage (I-V) curves for 20 modules in addition to measurement of modules with fixed loads as had been done in the past.

Anspaugh, B. E.↗
NASA NTRS1995

Straw man trade between multi-junction, gallium arsenide, and silicon solar cells

Multi-junction (MJ), gallium arsenide (GaAs), and silicon (Si) solar cells have respective test efficiencies of approximately 24%, 18.5% and 14.8%. Multi-junction and gallium arsenide solar cells weigh more than silicon solar cells and cost approximately five times as much per unit power at the cell level. A straw man trade is performed for the TRMM spacecraft to determine which of these cell types would have offered an overall performance and price advantage to the spacecraft. A straw man trade is also performed for the multi-junction cells under the assumption that they will cost over ten times that of silicon cells at the cell level. The trade shows that the TRMM project, less the cost of the instrument, ground systems and mission operations, would spend approximately $552 thousand dollars per kilogram to launch and service science in the case of the spacecraft equipped with silicon solar cells. If these cells are changed out for gallium arsenide solar cells, an additional 31 kilograms of science can be launched and serviced at a price of approximately $90 thousand per kilogram. The weight reduction is shown to derive from the smaller area of the array and hence reductions in the weight of the array substrate and supporting structure. If the silicon solar cells are changed out for multi-junction solar cells, an additional 45 kilograms of science above the silicon base line can be launched and serviced at a price of approximately $58 thousand per kilogram. The trade shows that even if the multi-junction arrays are priced over ten times that of silicon cells, a price that is much higher than projected, that the additional 45 kilograms of science are launched and serviced at $182 thousand per kilogram. This is still much less than original $552 thousand per kilogram to launch and service the science. Data and qualitative factors are presented to show that these figures are subject to a great deal of uncertainty. Nonetheless, the benefit of the higher efficiency solar cells for TRMM is far greater than the uncertainties in the analysis.

Gaddy, Edward M.↗
NASA NTRS1994

Modeling of high efficiency solar cells under laser pulse for power beaming applications

Solar cells have been used to convert sunlight to electrical energy for many years and also offer great potential for non-solar energy conversion applications. Their greatly improved performance under monochromatic light compared to sunlight, makes them suitable as photovoltaic (PV) receivers in laser power beaming applications. Laser beamed power to a PV array receiver could provide power to satellites, an orbital transfer vehicle, or a lunar base. Gallium arsenide (GaAs) and indium phosphide (InP) solar cells have calculated efficiencies of more than 50 percent under continuous illumination at the optimum wavelength. Currently high power free-electron lasers are being developed which operate in pulsed conditions. Understanding cell behavior under a laser pulse is important in the selection of the solar cell material and the laser. An experiment by NAsA lewis and JPL at the AVLIS laser facility in Livermore, CA presented experimental data on cell performance under pulsed laser illumination. Reference 5 contains an overview of technical issues concerning the use of solar cells for laser power conversion, written before the experiments were performed. As the experimental results showed, the actual effects of pulsed operation are more complicated. Reference 6 discusses simulations of the output of GaAs concentrator solar cells under pulsed laser illumination. The present paper continues this work, and compares the output of Si and GaAs solar cells.

Jain, Raj K.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon (HEM) showed a maximum AMO efficiency of 10.1%. Cells from the low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6%. Maximum AMO efficiency of the standard solar cells from the EFG (RH) ribbons was about 7.5%. The solar cells from the controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4%. The average AMO efficiency of the standard SOC solar cells were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗
NASA NTRS1968

Pioneer's solar-cell array.

Solar array as primary electrical power source of Pioneer deep space probes, comparing performance data with test and design data

Baron, W. R.↗
NASA NTRS1979

The NASA Lewis Research Center program in space solar cell research and technology

Progress in space solar cell research and technology is reported. An 18 percent-AMO-efficient silicon solar cell, reduction in the radiation damage suffered by silicon solar cells in space, and high efficiency wrap-around contact and thin (50 micrometer) coplanar back contact silicon cells are among the topics discussed. Reduction in the cost of silicon cells for space use, cost effective GaAs solar cells, the feasibility of 30 percent AMO solar energy conversion, and reliable encapsulants for space blankets are also considered.

Brandhorst, H. W., Jr.↗
NASA NTRS2012

Coating Processes Boost Performance of Solar Cells

NASA currently has spacecraft orbiting Mercury (MESSENGER), imaging the asteroid Vesta (Dawn), roaming the red plains of Mars (the Opportunity rover), and providing a laboratory for humans to advance scientific research in space (the International Space Station, or ISS). The heart of the technology that powers those missions and many others can be held in the palm of your hand - the solar cell. Solar, or photovoltaic (PV), cells are what make up the panels and arrays that draw on the Sun s light to generate electricity for everything from the Hubble Space Telescope s imaging equipment to the life support systems for the ISS. To enable NASA spacecraft to utilize the Sun s energy for exploring destinations as distant as Jupiter, the Agency has invested significant research into improving solar cell design and efficiency. Glenn Research Center has been a national leader in advancing PV technology. The Center s Photovoltaic and Power Technologies Branch has conducted numerous experiments aimed at developing lighter, more efficient solar cells that are less expensive to manufacture. Initiatives like the Forward Technology Solar Cell Experiments I and II in which PV cells developed by NASA and private industry were mounted outside the ISS have tested how various solar technologies perform in the harsh conditions of space. While NASA seeks to improve solar cells for space applications, the results are returning to Earth to benefit the solar energy industry.

Source record↗
NASA NTRS1977

High efficiency GaAs solar cells

The present status of the GaAlAs/GaAs heteroface solar cell program is reported. Studies have been concentrated on GaAlAs/GaAs heteroface solar cells; however, some research has been conducted on thin junction, diffused GaAs solar cells. Emphasis has been on obtaining high efficiency (18% to 20%) GaAs solar cells. Two problems that have limited the efficiency of GaAs solar cells are the high recombination velocity of carriers near the surface and the low minority carrier diffusion length in n-GaAs.

Walker, G. H.↗
NASA NTRS1994

Summary of solar cell data from the Long Duration Exposure Facility (LDEF)

The Long Duration Exposure Facility (LDEF) was composed of many separate experiments, some of which contained solar cells. These solar cells were distributed at various positions on the LDEF and, therefore, were exposed to the space environment with an orientational dependence. This report will address the space environmental effects on solar cells and solar cell assemblies (SCA's), including electrical interconnects and associated insulation blankets where flown in conjunction with solar cells.

Hill, David C.↗