Search NASA⌕ Search

SEARCH · Search NASA

Results for “Spalling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Oxidation behavior of Fe-Cr-2Si alloys in high temperature steam

FeCrSi alloys have been proposed as alternatives to FeCrAl alloys for accident-tolerant fuel cladding in light water reactors. Experiments on the oxidation resistance of three Fe-Cr-2Si alloys in high-temperature steam, with 12, 16, and 20 wt. % Cr, show that ≥16 % Cr is sufficient to form a thin, passivating, binary oxide layer. Additionally, at 1200 °C, only Cr 2 O 3 and SiO 2 form on Fe 16 Cr 2 Si and Fe 20 Cr 2 Si, while additional ternary Fe oxides form on Fe 12 Cr 2 Si. Decohesion and spalling of oxide were observed on Fe-Cr-Si alloys exposed to steam at 900 °C and above. Fe 20 Cr 2 Si exhibits the best oxidation resistance of the three in high-temperature steam.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cyclic oxidation behavior of selected commercial NiCr-alloys for engine exhaust valves in wet air environment between 800 and 950 °C

In this work, the impact of water vapor on the cyclic oxidation behavior of four commercial Ni-based superalloys (N80A, N90, R41 and H282) was investigated between 800 and 950°C. Oxidation- and volatilization-induced Cr loss accelerated the transition from protective and adherent oxide formation (Cr 2 O 3 ) to mixed oxides that significantly spalled at 950°C for H282 and R41. The accelerated oxidation, Cr depletion, and spallation susceptibility for R41 and to a lesser extent for H282 compared to N80A and N90 was related to the higher fraction of γ’, which led to increased Ti incorporation into the Cr 2 O 3 scale in the presence of water vapor.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reformulating a Gurson-based dynamic damage model and demonstrating improved predictive power and numerical robustness

The original Tepla (TEnsile PLAsticity) ductile damage model, based on the Gurson yield surface, has long been used to model damage evolution and material failure under dynamic loading. Unfortunately, Tepla suffered from mesh sensitivity, numerical instability, and limited predictive capability. Here, we theoretically reformulate Tepla to address these issues. We especially focus on the prediction of porosity, which is the key state variable used for modeling ductile damage, as compared to more easily measured surface velocities, which are at best an indirect measure of damage. Key model changes include separating the viscosity during volumetric void growth from underlying shear strength behavior and switching to an iterative bisection solver. The new Tepla is then calibrated on incipient spall experiments on half-hard copper and tantalum, which demonstrate its ability to simultaneously fit the model to recovered porosity distributions and measured surface velocities, a stringent test. Improved numerical behavior, such as greatly reduced mesh sensitivity, is also shown in those simulations. Finally, the new Tepla model is applied to several high-explosive loaded, sweeping wave experiments, showing the ability of the model to predict behavior on tests with significantly different loading conditions and histories than the calibration data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using electron channeling contrast imaging to inform and improve the growth of high-efficiency GaAs solar cells on nanopatterned GaAs substrates

Patterned substrates provide opportunities for reducing the cost of high-efficiency III-V devices by incorporating mechanically weak layers beneficial for substrate reuse (e.g. by spalling). In this work, the functionality of electron channeling contrast imaging (ECCI) as a tool to efficiently understand and mitigate defect formation is exemplified by developing a process in which high-quality III-V material can be grown on nanopatterned GaAs substrates. Reactive ion etching used in the patterning process was found to damage the GaAs substrate surface, leading to the formation of stacking faults in the epitaxial material as observed by ECCI. Etching the patterned substrates in a 1 NH4OH: 1 H2O2: 50 DI H2O solution for 10 s prior to growth removed the substrate surface damage and stacking faults were no longer present. Growth of solar cell device structures initially produced samples with many macroscale flaws creating shunts in the devices, which complicated the assessment of material quality by device measurements. However, ECCI revealed that the epitaxial material surrounding macroscale flaws was free from any crystallographic defects such as stacking faults and threading dislocations. With this knowledge, we focused on refining the patterning process to eliminate the macroscale flaws. Solar cells were then grown on the improved nanopatterned substrates and exhibited device structures with defect densities less than 5 x 105 cm -2 and average conversion efficiency of 24.8%, nearly identical to devices grown on unpatterned epi-ready substrates (25.0%).

14 SOLAR ENERGY↗
DOE OSTI2019

Compatibility of FeCrAlMo with flowing PbLi at 500°-650°C

To explore the upper temperature limit of a fusion blanket utilizing eutectic Pb-17at.%Li for tritium breeding, a series of three mono-metallic thermal convection loops have been fabricated from alloy APMT (Fe–21Cr–5Al–3Mo) and operated with commercial PbLi and increasing peak temperatures of 550°, 600° and 650 °C, flow rates of 0.4–0.7 cm/s and temperature gradients of 85–115 °C. Chains of APMT specimens including 25 mm long tensile specimens were hung in the hot and cold legs of the loops to evaluate post-exposure room temperature tensile properties after 1000 h exposures in each experiment. For specimens exposed to flowing PbLi above 500°C, only minor changes in tensile properties were observed after exposure. Most APMT specimens were pre-oxidized to form alumina prior to exposure and exhibited small mass losses as the alumina was partially transformed to α-LiAlO 2 that tended to spall after exposure. Specimens without pre-oxidation exhibited higher mass losses and formed γ-LiAlO 2 but with less spallation. While promising for increasing blanket temperatures, the small mass losses suggest that the surface oxide is not completely stable. In conclusion, even at the highest temperatures, there was no indication of classic dissolution/precipitation behavior suggesting that higher temperature compatibility may be possible.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evaluation of the effects of neutron irradiation on first-generation corrosion mitigation coatings on SiC for accident-tolerant fuel cladding

In this work, high purity SiC and SiC/SiC composites coated with commercial TiN, Cr, CrN, or CrN/Cr multilayer coatings were irradiated in Ar or flowing PWR water in the Massachusetts Institute of Technology Nuclear Reactor Laboratory (MITR). Irradiation in Ar was performed in the core. In the water environment, identical samples were placed in one of three different locations: in-core, providing exposure to neutron damage and radiolysis-affected water; above-core, where samples were exposed to radiolysis-affected water but not neutron damage, or outside of the core, where samples were exposed to the coolant water without the effects of radiation. Radiation in Ar revealed significant cracking of all but the TiN coatings, attributed to differential swelling between the coating and substrate. Lattice swelling was not observed in any of the coatings, but 0.2% void swelling was observed in the Cr coating. All of the coatings failed during water exposures in the core. Likewise, CrN/Cr spalled in each condition. Cr was protective, except under radiation damage as a result of cracking, and TiN severely degraded in the core with no coating was found following exposure. A SiC/coating ATF cladding system is anticipated to perform adequately following improvements in coating ductility and purity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Corrosion behavior of a series of combinatorial physical vapor deposition coatings on SiC in a simulated boiling water reactor environment

Here, the simulated boiling water condition corrosion properties of multilayer and combinatorial physical vapor deposition metal coatings (Zr, Cr, and/or Ti) deposited on a SiC f -SiC composite were investigated. Various compositions within the ternary system were corroded to the most suitable composition preventing underlying SiC f -SiC from further attack. Mass measurements and visual observations were conducted to identify which coatings formed protective oxides and which coatings spalled. Transmission electron microscopy was conducted to observe the microstructure of the physical vapor deposition metal layer before and after corrosion as well as identify the oxide which were forming.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Adhesion, structure, and mechanical properties of Cr HiPIMS and cathodic arc deposited coatings on SiC

Chromium deposited by high-power impulse magnetron sputtering (HIPIMS) versus cathodic arc (CA) processes exhibits very different mechanical properties. Combining the two can result in a single-phase with superior performance that can be tailored for use in coating SiC for advanced nuclear fuel cladding. Coating morphology, residual stress, elemental depth profiles, and mechanical testing by scratch, pull-off adhesion, and microcantilevers are shown for HiPIMS, CA, and combined coatings. CA coatings were likely to spall and had lower adhesion strength due to tensile residual stresses but had desirable material properties. Additionally, by depositing an initial layer of Cr by HiPIMS followed by a layer of Cr by CA, a more adherent coating was achieved and some of the stress issues with CA morphology were resolved. Combined coatings withstood at least 80 MPa in pull-off adhesion tests and had maximum failure stress values of 5GPa in microcantilever tests. These results were better than either individual deposition method and point to a hybrid approach being a path forward for a more robust coating.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Generation of Subsurface Voids, Incubation Effect, and Formation of Nanoparticles in Short Pulse Laser Interactions with Bulk Metal Targets in Liquid: Molecular Dynamics Study

The ability of short pulse laser ablation in liquids to produce clean colloidal nanoparticles and unusual surface morphology has been employed in a broad range of practical applications. In this paper, we report the results of large-scale molecular dynamics simulations aimed at revealing the key processes that control the surface morphology and nanoparticle size distributions by pulsed laser ablation in liquids. The simulations of bulk Ag targets irradiated in water are performed with an advanced computational model combining a coarse-grained representation of liquid environment and an atomistic description of laser interaction with metal targets. For the irradiation conditions that correspond to the spallation regime in vacuum, the simulations predict that the water environment can prevent the complete separation of the spalled layer from the target, leading to the formation of large subsurface voids stabilized by rapid cooling and solidification. The subsequent irradiation of the laser-modified surface is found to result in a more efficient ablation and nanoparticle generation, thus suggesting the possibility of the incubation effect in multipulse laser ablation in liquids. The simulations performed at higher laser fluences that correspond to the phase explosion regime in vacuum reveal the accumulation of the ablation plume at the interface with the water environment and the formation of a hot metal layer. The water in contact with the metal layer is brought to the supercritical state and provides an environment suitable for nucleation and growth of small metal nanoparticles from metal atoms emitted from the hot metal layer. The metal layer itself has limited stability and can readily disintegrate into large (tens of nanometers) nanoparticles. The layer disintegration is facilitated by the Rayleigh–Taylor instability of the interface between the higher density metal layer decelerated by the pressure from the lighter supercritical water. The nanoparticles emerging from the layer disintegration are rapidly cooled and solidified due to the interaction with water environment, with a cooling rate of ~2 × 10 12 K/s observed in the simulations. The computational prediction of two distinct mechanisms of nanoparticle formation yielding nanoparticles with different characteristic sizes provides a plausible explanation for the experimental observations of bimodal nanoparticle size distributions in laser ablation in liquids. The ultrahigh cooling and solidification rates suggest the possibility for generation of nanoparticles featuring metastable phases and highly nonequilibrium structures.

Chemistry↗
DOE OSTI2024

Millimeter-Scale Exfoliation of hBN with Tunable Flake Thickness for Scalable Encapsulation

As a two-dimensional (2D) dielectric material, hexagonal boron nitride (hBN) is in high demand for applications in photonics, nonlinear optics, and nanoelectronics. Unfortunately, the high-throughput preparation of macroscopic-scale, high-quality hBN flakes with controlled thickness is an ongoing challenge, limiting device fabrication and technological integration. In this report we present a metal thin-film exfoliation method to prepare hBN flakes with millimeter-scale dimension, near-unity yields, and tunable flake thickness distribution from 1-7 layers, a substantial improvement over scotch tape exfoliation. The single crystallinity and high quality of the exfoliated hBN are demonstrated with optical microscopy, atomic force microscopy, Raman spectroscopy, and second harmonic generation. We further explore a possible mechanism for the effectiveness and selectivity based on thin-film residual stress measurements, density functional theory calculations, and transmission electron microscopy imaging of the deposited metal films. We find that the magnitude of the residual tensile stress induced by thin film deposition plays a key role in determining exfoliated flake thickness in a manner which closely resembles 3D semiconductor spalling. Lastly, we demonstrate that our exfoliated, large-area hBN flakes can be readily incorporated as encapsulating layers for other 2D monolayers. Altogether, this method brings us one step closer to the high throughput, mass production of hBN-based 2D photonic, optoelectronic, and quantum devices.

2D materials↗
DOE OSTI2024

Shallow Soil Response to a Buried Chemical Explosion With Geophones and Distributed Acoustic Sensing

Abstract Shallow sediments can respond non‐linearly to large dynamic strains and undergo a subsequent healing phase as the material gradually recovers following the passing of seismic waves. This study focuses on the physical changes in the subsurface caused by the shaking from a buried chemical explosion detonated in a borehole in Nevada, USA, as a part of the Source Physics Experiment Phase II. The explosion damaged the shallow subsurface and modified the frequency content recorded by 491 geophones and 2240 Distributed Acoustic Sensing (DAS) channels within 2.5 km from surface ground zero. We observe a gradual shift of resonance frequencies in the 10–25 Hz frequency band in the hours following the explosion and develop a method to characterize the related logarithm‐type healing process of the shallow (i.e., upper ∼25 m) subsurface. We find that stronger levels of ground motion increase the relative degree of damage and duration of the subsurface healing; with the spall region exhibiting the largest degree of damage and longest healing recovery time. We observe coherent spatial patterns of damage with the region located to the southeast of the explosion exhibiting more damage than the southwest region. This study demonstrates that both DAS and co‐located geophones capture similar temporal changes associated with the physical processes occurring in the subsurface, with the high‐density sampling of DAS measurements enabling a new capability to monitor the fine‐scale changes of the Earth's shallow subsurface following the detonation of a buried explosion.

Viens, Loïc↗
DOE OSTI2021

StressNet - Deep learning to predict stress with fracture propagation in brittle materials

Abstract Catastrophic failure in brittle materials is often due to the rapid growth and coalescence of cracks aided by high internal stresses. Hence, accurate prediction of maximum internal stress is critical to predicting time to failure and improving the fracture resistance and reliability of materials. Existing high-fidelity methods, such as the Finite-Discrete Element Model (FDEM), are limited by their high computational cost. Therefore, to reduce computational cost while preserving accuracy, a deep learning model, StressNet, is proposed to predict the entire sequence of maximum internal stress based on fracture propagation and the initial stress data. More specifically, the Temporal Independent Convolutional Neural Network (TI-CNN) is designed to capture the spatial features of fractures like fracture path and spall regions, and the Bidirectional Long Short-term Memory (Bi-LSTM) Network is adapted to capture the temporal features. By fusing these features, the evolution in time of the maximum internal stress can be accurately predicted. Moreover, an adaptive loss function is designed by dynamically integrating the Mean Squared Error (MSE) and the Mean Absolute Percentage Error (MAPE), to reflect the fluctuations in maximum internal stress. After training, the proposed model is able to compute accurate multi-step predictions of maximum internal stress in approximately 20 seconds, as compared to the FDEM run time of 4 h, with an average MAPE of 2% relative to test data.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Early-stage uranium-hydrogen corrosion kinetics and mechanism

Research into the early-stage uranium-hydrogen degradation mechanism lacks unified interpretation and understanding due to inadequate temporal and spatial characterization resolution required to unify reaction observations. In this study, white-light interferometry was adapted to characterize the uranium-hydrogen reaction at a temperature of 50 °C and hydrogen pressure of 13.8 kPa. The uranium surface remained unchanged for 62 min during the hydride induction period before the first hydride blister appeared. This blister was monitored from induction through critical spallation and UH₃ powder release during rapid surface hydriding. The critical spallation dimensions measured for height, diameter, area, and perimeter of the first blister were 1.79 µm, 17.58 µm, 187.7 µm 2 and 59.79 µm. Hydriding growth kinetics were assessed by tracking the first hydride site over the reaction time. Analysis shows that the spall-front velocity of the hydride was changing at a rate of 0.91 µm/min which compares favorably with legacy Sievert’s experiments in literature. Total percentage of the surface area hydrided after 242 min was 42.7%, and post-characterization of the UH 3 powders shows both α-UH 3 and β-UH 3 . This work highlights the strength of characterizing the early-stage uranium-hydrogen reaction using white-light interferometry, but more importantly, unifying the understanding and mechanism of the uranium-hydrogen reaction kinetics.

Materials science↗
DOE OSTI2017

Residual stress determination in oxide layers at different length scales combining Raman spectroscopy and X-ray diffraction: Application to chromia-forming metallic alloys

In oxidizing environments, the protection of metals and alloys against further oxidation at high temperature is provided by the oxide film itself. This protection is efficient only if the formed film adheres well to the metal (substrate), i.e., without microcracks and spalls induced by thermomechanical stresses. In this study, the residual stresses at both macroscopic and microscopic scales in the oxide film adhering to the substrate and over the damaged areas have been rigorously determined on the same samples for both techniques. Ni-30Cr and Fe-47Cr alloys have been oxidized together at 900 and 1000 °C, respectively, to create films with a thickness of a few microns. A multi-scale approach was adopted: macroscopic stress was determined by conventional X-ray diffraction and Raman spectroscopy, while microscopic residual stress mappings were performed over different types of bucklings using Raman micro-spectroscopy and synchrotron micro-diffraction. A very good agreement is found at macro- and microscales between the residual stress values obtained with both techniques, giving confidence on the reliability of the measurements. In addition, relevant structural information at the interface between the metallic substrate and the oxide layer was collected by micro-diffraction, a non-destructive technique that allows mapping through the oxide layer, and both the grain size and the crystallographic orientation of the supporting polycrystalline metal located either under a buckling or not were measured.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Dynamic strength properties and alpha-phase shock Hugoniot of iron and steel

The properties of iron and steel are of considerable interest scientifically to the dynamic materials properties' community, as well as to a broader audience, for many applications. This is true in part because of the existence of a solid-solid phase (α–ε) transition at relatively modest stress (13 GPa). Because of this, there is a significant amount of data on iron and steel alloy shock compression properties at stresses above 13 GPa, but much less fundamental data under stress conditions lower than that, where the metals are in the α-phase. New data have been obtained under relatively low stress (below 10 GPa) conditions in which samples are subjected to low-velocity symmetric impact on the order of 0.2 to 0.4 km/s. We used well-developed flyer plate impact methods combined with velocity interferometry to measure wave speeds and strength properties in compression and tension. The shock α-phase Hugoniot data reported here are compared with literature values. A comparison of spall strength and Hugoniot elastic limit is made between different types of steel studied and for pure iron.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing the properties and mechanisms of failure waves in soda-lime glass

Soda-lime glass (SLG) and other silica glasses exhibit the failure wave phenomenon under shock compression. The mechanism responsible for this peculiar behavior of glasses is still unresolved. In this study, a series of plate impact experiments was performed at three different impact stresses of 6.4, 8.3, and 10.8 GPa to better understand the mechanisms underlying the failure wave phenomenon. Specifically, spall experiments were conducted to probe the speed and existence of failure waves at different stresses in SLG. A layered glass target was used to probe the possibility of a “renucleation” of the wave at the SLG–SLG interface. When it existed, the failure wave was inferred to propagate at a speed of 1.3 km/s. However, it was observed that the failure wave phenomenon ceases to exist for impact stresses higher than 10 GPa. In experiments with a 6.4 GPa impact stress, the peak free surface velocity was significantly less than what is predicted by stress-Hugoniot calculations. This velocity deficit and other important features of the measured free surface velocity profiles were simulated using finite element analysis by incorporating an abrupt densification of SLG at a critical stress in the equation of state. Furthermore, this densification feature is similar to what would be expected of a phase transition. Although unable to unambiguously reveal the mechanism causing the failure wave phenomenon, the results of the present work clearly indicate that the failure wave causes a secondary compression and densification in SLG.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding the phase transformation mechanisms that affect the dynamic response of Fe-based microstructures at the atomic scales

Large-scale molecular dynamics (MD) simulations were carried out to investigate the shock-induced evolution of microstructure in Fe-based systems comprising single-crystal and layered Cu/Fe alloys with a distribution of interfaces. The shock compression of pure single-crystal Fe oriented along [110] above a threshold pressure results in a BCC (α)→HCP (ε) phase transformation behavior that generates a distribution of ε phase variants in the phase transformed region of the microstructure behind the shock front. The propagation of the release wave through a phase transformed ε phase causes a reverse ε→α phase transformation and renders a distribution of twins for the [110] oriented Fe that serve as void nucleation sites during spall failure. The simulations reveal that the α→ε→α transformation-induced twinning for shock loading along the [110] direction is due to a dominant ε phase variant formed during compression that rotates on the arrival of the release wave followed by a reverse phase transformation to twins in the α phase. The modifications in the evolution of the ε phase variants and twins in Fe behavior are also studied for Cu–Fe layered microstructures due to the shock wave interactions with the Cu/Fe interfaces using a newly constructed Cu–Fe alloy potential. Here, the MD simulations suggest that interfaces affect the observed variants during shock compression and, hence, distributions of twins during shock release that affects the void nucleation stresses in the Fe phase of Cu/Fe microstructures.

36 MATERIALS SCIENCE↗