Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sputtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Atomic layer deposited (ALD) “leaky” TiO 2 have gained interest as charge-selective protection layers for semiconductor solar fuel electrodes. Here we demonstrate the use of sputter-deposited TiO 2 layers as hole selective contacts for WO 3 /CuWO 4 type 2 heterojunction water oxidation photoanodes for the first time. TiO 2 protection layers with varying thicknesses (2 to 128 nm) were deposited using the RF magnetron sputtering technique. The resulting TiO 2 films are amorphous based on Raman spectroscopy and powder XRD. Photoelectrochemical scans and Vibrating Kelvin probe photovoltage spectroscopy show that 2-8 nm TiO 2 layers nearly double the photocurrent to 0.97 mA cm -2 under AM 1.5 illumination (19% AQE at 350 nm), increase the surface photovoltage signal by 25%, and increase the WO 3 /CuWO 4 bandgap. These effects can be attributed to the selectivity of TiO 2 for photoholes. Additionally, SPV data suggest that TiO 2 overlayers suppress copper-based surface recombination defects. Reduced photocurrent and the photovoltage are seen in thicker TiO 2 films (16 to 128 nm) as a result of an increasing hole transfer resistance and because of light shading effects according to photoaction spectra. The TiO 2 films also improve the stability of the WO 3 /CuWO 4 photoelectrodes, allowing nearly constant O 2 evolution over 3 hours after an initial 20-35% loss. Overall, this work establishes RF magnetron sputtering as a useful method to install amorphous TiO 2 passivation layers for improved WO 3 /CuWO 4 solar fuel photoelectrodes. Furthermore, we show how the combination of PEC with SPV measurements provides insight into the function of the TiO 2 coatings.

CuWO4↗

Damage mechanisms in thin film solar cells during sputtering deposition of transparent conductive coatings

Amorphous silicon (a-Si) based thin film solar cell grown on flexible stainless steel substrate is one of the most promising energy conversion devices in the future. This type of solar cell uses a transparent conductive oxide (TCO) film as top electrode. It has been a widely accepted opinion that the radio frequency sputtering deposition of the TCO film produces a higher yield than direct current sputtering, and the reason is not clear. Here we show that the damage to the solar cell during the sputtering process is caused by a reverse bias applied to the n-i-p junction. This reverse bias is related to the characteristics of plasma discharge. The mechanism we reveal may significantly affect the solar cell process.

36 MATERIALS SCIENCE↗

The effect of the sputtering gas (Ar, Xe) on FePt clusters formation: structural and magnetic properties

It will be reported about the effect of the sputtering gases, Ar and Xe, on FePt clusters formation by magnetron sputtering deposition at high working pressures. All layers, with bulk equivalent thicknesses between 3 to 5 nm, were realized at RT by a sequential layer by layer deposition or a co-deposition of Fe and Pt. After rapid thermal annealing at 500 deg. C, the highest L1{sub 0} fraction was found using Xe as sputtering gas: Xe decreases the transformation activation energy and therefore, reduces the critical thickness necessary to obtain the high anistropic ferromagnetic phase. Ar assisted growths lead to FePt clusters in the L1{sub 0} phase only if the sequential layer deposition is used, whereas for Xe no differences in the deposition techniques were observed.

36 MATERIALS SCIENCE↗

Ion-energy distributions at a substrate in reactive magnetron sputtering discharges in Ar/H{sub 2}S from copper, indium, and tungsten targets

Ion-energy distributions from copper, indium, and tungsten targets were measured during reactive sputtering in argon-hydrogen sulfide (H{sub 2}S) mixtures, since reactive magnetron sputtering of sulfides from metallic targets is of increasing interest, especially for photovoltaic applications (buffer and absorber layers, i.e., CuInS{sub 2}, In{sub 2}S{sub 3}, or WS{sub 2}). The mass spectra of the ions show a wide range of molecules H{sub x}S{sub n} derived from H{sub 2}S by plasma-assisted attachment both for positive (n{<=}9) and for negative (n{<=}6) ions. From the copper and the indium targets metallic ions (Cu{sup +}, In{sup +}) could be detected. While tungsten and indium sulfur compounds were found, copper does not form compounds with sulfur, caused by its lower chemical reactivity. Positive (Ar{sup +}, S{sup +}, W{sup +}, Cu{sup +}, In{sup +}, etc.) as well as negative ions (S{sup -}, InS{sup -}, WS{sub 3}{sup -}) were measured for dc and rf (27 MHz) plasma excitations. The positive ions originate mainly from the plasma in front of the substrate and exhibit energies of about 12 eV for the dc and 18 eV for the rf discharge for the substrate at floating potential. The energy difference is caused by the higher electron temperature in the rf compared to the dc discharge. The ion-energy distributions of negative ions exhibit two distinct peaks. The high-energetic peak can be attributed to ions accelerated in the cathode dark space to a high energy (up to more than 400 eV) corresponding to the cathode (target) voltage. The second peak has its maximum at zero energy decreasing steeply up to energies of about 100 eV. These ions are generated by charge-exchange collisions of energetic species from the target (reflected neutral argon, negative sulfur ions, etc.) on their passage from the target to the substrate caused by the high charge-exchange cross section. rf magnetron sputtering leads to significantly lower energies of negative ions from the target, caused by the lower discharge voltages, which could be advantageous for the deposition of active semiconducting sulfide films.

36 MATERIALS SCIENCE↗

Formation, trapping, and ejection of radiolytic O{sub 2} from ion-irradiated water ice studied by sputter depth profiling

We report experimental studies of 100 keV Ar{sup +} ion irradiation of ice leading to the formation of molecular oxygen and its trapping and ejection from the surface, at temperatures between 80 and 150 K. The use of a mass spectrometer and a quartz-crystal microbalance and sputter depth profiling at 20 K with low energy Ar ions allowed us to obtain a consistent picture of the complex radiolytic mechanism. We show that the dependence of O{sub 2} sputtering on ion fluence is mainly due to the buildup of trapped O{sub 2} near the surface. A small proportion of the O{sub 2} is ejected above 130 K immediately upon creation from a precursor such as OH or H{sub 2}O{sub 2}. The distribution of trapped oxygen peaks at or near the surface and is shallower than the ion range. Measurements of sputtering of H{sub 2} help to elucidate the role of this molecule in the process of O{sub 2} formation: out-diffusion leading to oxygen enrichment near the surface. The competing phenomena of OH diffusion away from the ion track and hydrogen escape from the ice and their temperature dependence are used to explain the finding of opposite temperature dependencies of O{sub 2} and H{sub 2}O{sub 2} synthesis. Based on the new data and understanding, we discuss the application of our findings to ices in the outer solar system and interstellar space.

36 MATERIALS SCIENCE↗

Plasma 'anti-assistance' and 'self-assistance' to high power impulse magnetron sputtering

A plasma assistance system was investigated with the goal to operate high power impulse magnetron sputtering (HiPIMS) at lower pressure than usual, thereby to enhance the utilization of the ballistic atoms and ions with high kinetic energy in the film growth process. Gas plasma flow from a constricted plasma source was aimed at the magnetron target. Contrary to initial expectations, such plasma assistance turned out to be contraproductive because it led to the extinction of the magnetron discharge. The effect can be explained by gas rarefaction. A better method of reducing the necessary gas pressure is operation at relatively high pulse repetition rates where the afterglow plasma of one pulse assists in the development of the next pulse. Here we show that this method, known from medium-frequency (MF) pulsed sputtering, is also very important at the much lower pulse repetition rates of HiPIMS. A minimum in the possible operational pressure is found in the frequency region between HiPIMS and MF pulsed sputtering.

36 MATERIALS SCIENCE↗

CdS Film Thickness Characterization By R. F. Magnetron Sputtering

In this work, cadmium sulphide (CdS) target with 99.999% purity was used as a target in RF magnetron sputtering. The sputtering experiment was conducted onto silicon oxide substrates at different temperatures ranging from 200 deg. C to 400 deg. C in 50 deg. C steps, using a capacitive coupled magnetron cathode with 13.65 MHz that at higher magnetron power. After all investigations, it was concluded that 300 deg. C substrate temperature is suitable for producing CdS films on silicon wafer with RF magnetron sputtering and the examined properties (good crystallinity and low resistivity) of this film show its feasibility for technological purposes, especially for light sensor cells.

36 MATERIALS SCIENCE↗

Influence of sputter rate and crystal orientation on the distribution of carbon in polycrystalline copper surfaces treated by plasma immersion ion implantation

The sputter rate influences the resulting thickness of the carbon containing layer within a surface that was treated by plasma immersion ion implantation. Choosing a polycrystalline substrate with rather large crystals and a material with an inherent high sputter rate, inhomogeneous distributions of carbon over the substrate area due to different thicknesses of the incorporated carbon can be detected. A correlation of three factors namely the carbon x-ray intensity in electron probe microanalysis, the thickness of the carbon layer, and the sputter rate in depth profiling measurements via secondary ion mass spectrometry can be shown. Essential for these factors is the crystal orientation that is visualized by mapping via electron backscatter diffraction. The differences in carbon content due to the orientation are most likely one of the reasons that the adhesion of diamond-like carbon films on copper does not improve with an interlayer of implanted carbon.

36 MATERIALS SCIENCE↗

Laser-Aided Diagnostics of Atoms and Particulates in Magnetron Sputtering Plasmas

Laser-aided diagnostic technique is introduced as an advanced and valuable technique to evaluate the properties of plasma. This technique is an expensive and sophisticated technique which requires researchers to have a basic knowledge in optical spectroscopy. In the present paper, we will generally introduce the experimental work using laser-induced fluorescence (LIF) and laser light scattering (LLS) techniques. The LIF was used to evaluate the spatial distribution of Cu atoms in magnetron sputtering plasma. The change in the spatial distribution was studied as a function of discharge power. On the other hand, the LLS was used to evaluate the generation of Cu particulates in high-pressure magnetron sputtering plasma. The temporal evolution of Cu particulates in the gas phase of sputtering plasma was visualized successfully.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation of metal nanoparticles by short-distance sputter deposition in a reactive ion etching chamber

A new method is reported to form metal nanoparticles by sputter deposition inside a reactive ion etching chamber with a very short target-substrate distance. The distribution and morphology of nanoparticles are found to be affected by the distance, the ion concentration, and the sputtering time. Densely distributed nanoparticles of various compositions were fabricated on the substrates that were kept at a distance of 130 mum or smaller from the target. When the distance was increased to 510 mum, island structures were formed, indicating the tendency to form continuous thin film with longer distance. The observed trend for nanoparticle formation is opposite to the previously reported mechanism for the formation of nanoparticles by sputtering. A new mechanism based on the seeding effect of the substrate is proposed to interpret the experimental results.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Boron ion source based on planar magnetron discharge in self-sputtering mode

An ion source based on a planar magnetron sputtering device with thermally isolated target has been designed and demonstrated. For a boron sputtering target, high target temperature is required because boron has low electrical conductivity at room temperature, increasing with temperature. The target is well-insulated thermally and can be heated by an initial low-current, high-voltage discharge mode. A discharge power of 16 W was adequate to attain the required surface temperature (400 C), followed by transition of the discharge to a high-current, low-voltage mode for which the magnetron enters a self-sputtering operational mode. Beam analysis was performed with a time-of-flight system; the maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. We have plans to make the ion source steady state and test with a bending magnet. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF3, and could be useful for semiconductor industry application.

43 PARTICLE ACCELERATORS↗

A self-sputtering ion source: A new approach to quiescent metal ion beams

A new metal ion source is presented based on sustained self-sputtering plasma in a magnetron discharge. Metals exhibiting high self-sputtering yield such as Cu, Ag, Zn, and Bi can be used in a high-power impulse magnetron sputtering discharge such that the plasma almost exclusively contains singly charged metal ions of the target material. The plasma and extracted ion beam are quiescent. The ion beams consist mostly of singly charged ions with a space-charge limited current density which reached about 10 mA/cm{sup 2} at an extraction voltage of 45 kV and a first gap spacing of 12 mm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modeling of iron oxide deposition by reactive ion beam sputtering

An analytic model of deposition is applied on reactive ion beam sputtering to optimize the properties of iron oxide thin films. This model will be able to predict deposition rate and phase contents. Among its hypotheses, we assume oxygen adsorption at the surface of the target to explain variations of deposition rate for oxygen flow. This hypothesis is validated by chemical analyses on iron targets. An ellipsoidal distribution of probability is introduced to model sputtered matter distribution from iron target and to calculate sputtering yield. Comparison between experimental and calculated deposition rates validates previously assumed hypotheses.

36 MATERIALS SCIENCE↗

Effect of substrate roughness on the apparent surface free energy of sputter deposited superhydrophobic polytetrafluoroethylene coatings: A comparison of experimental data with different theoretical models

We have studied the effect of substrate roughness on the wettability and the apparent surface free energy (SFE) of sputter deposited polytetrafluoroethylene (PTFE) coatings deposited on untreated glass (average roughness, R{sub a}=2.0 nm), plasma etched glass (R{sub a}=7.4 nm), and sandblasted glass (R{sub a}=4500 nm) substrates. The wettability of the PTFE coatings deposited on substrates with varying roughnesses was evaluated by measuring the apparent contact angle (CA) using a series of probe liquids from nonpolar aprotic to polar protic. The wettability measurements indicate that an apparent water CA of 152 deg. with a sliding angle of 8 deg. was achieved for PTFE coatings deposited on a substrate with R{sub a}=4500 nm. The superhydrophobicity observed in these coatings is attributed to the presence of dual scale roughness, densely packed microstructure and the presence of CF{sub 3} groups. Unlike the bulk PTFE which is mainly dispersive, the sputter deposited PTFE coatings are expected to have some degree of polar component due to the plasma treatment. In order to calculate the dispersive SFE of PTFE coatings, we have used the Girifalco-Good-Fowkes (GGF) method and validated it with the Zisman model. Furthermore, the Owens-Wendt model has been used to calculate the dispersive and the polar components of the apparent SFE of the PTFE coatings. These results are further corroborated using the Fowkes method. Finally, an ''equation of state'' theory proposed by Neumann has been used to calculate the apparent SFE values of the PTFE coatings. The results indicate that the apparent SFE values of the PTFE coatings obtained from the Owens-Wendt and the Fowkes methods are comparable to those obtained from the Neumann's method. The analyses further demonstrate that the GGF and the Zisman methods underestimate the apparent SFE values of the sputter deposited PTFE coatings.

36 MATERIALS SCIENCE↗

Time-resolved investigation of dual high power impulse magnetron sputtering with closed magnetic field during deposition of Ti-Cu thin films

Time-resolved comparative study of dual magnetron sputtering (dual-MS) and dual high power impulse magnetron sputtering (dual-HiPIMS) systems arranged with closed magnetic field is presented. The dual-MS system was operated with a repetition frequency 4.65 kHz (duty cycle {approx_equal}50%). The frequency during dual-HiPIMS is lower as well as its duty cycle (f=100 Hz, duty 1%). Different metallic targets (Ti, Cu) and different cathode voltages were applied to get required stoichiometry of Ti-Cu thin films. The plasma parameters of the interspace between magnetrons in the substrate position were investigated by time-resolved optical emission spectroscopy, Langmuir probe technique, and measurement of ion fluxes to the substrate. It is shown that plasma density as well as ion flux is higher about two orders of magnitude in dual-HiPIMS system. This fact is partially caused by low diffusion of ionized sputtered particles (Ti{sup +},Cu{sup +}) which creates a preionized medium.

36 MATERIALS SCIENCE↗

On the evolution of film roughness during magnetron sputtering deposition

The effect of long-range screening on the surface morphology of thin films grown with pulsed-dc (p-dc) magnetron sputtering is studied. The surface evolution is described by a stochastic diffusion equation that includes the nonlocal shadowing effects in three spatial dimensions. The diffusional relaxation and the angular distribution of the incident particle flux strongly influence the transition to the shadowing growth regime. In the magnetron sputtering deposition the shadowing effect is essential because of the configuration of the magnetron system (finite size of sputtered targets, rotating sample holder, etc.). A realistic angular distribution of depositing particles is constructed by taking into account the cylindrical magnetron geometry. Simulation results are compared with the experimental data of surface roughness evolution during 100 and 350 kHz p-dc deposition, respectively.

36 MATERIALS SCIENCE↗

Determination of sputtered atom densities and velocities via simulation

Transport of sputtered atoms in a plasma sputtering unit is simulated using two known elastic collision models. The methods of studying the collision of two atoms are isotropic random scattering angle in the center of mass frame and the so-called center to center collision model in which the impact parameter is ignored and the two particles collide such as two material points. The obtained results for the density and velocity of sputtered atoms in both models are compared with some experimental reports. This investigation shows that the copper and argon atoms present pointlike behavior in the collision process.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Sputtering Gas environments on the Properties of Aluminum-doped Zinc Oxide Thin Films for Photovoltaic Application

Aluminum-doped zinc oxide thin films have been deposited on glass substrates by R.F. sputtering using ZnO(98%)-Al{sub 2}O{sub 3}(2%) target in different sputtering gaseous environments, viz., Ar, Ar/O{sub 2} and Ar/N{sub 2}+H{sub 2} at 80 deg. C. These films have been studied with regard to phase, microstructure, optical absorption and sheet resistance for application in photovoltaic devices as transparent conducting electrodes. The properties of the films are shown to strongly depend on the sputtering gas(es). The films exhibit a wurtzite-type hexagonal structure with the (00.2) preferred orientation, the c-axis perpendicular to the substrate. The intensity of 00.2 diffraction peak and the average crystallite size remain almost the same when the films are prepared under pure Ar or Ar/O{sub 2} environment. However the average crystallite size increases while electrical resistance decreases with introduction of nitrogen and hydrogen in comparison to oxygen in argon. Nevertheless, the optimum value of optical transmittance and sheet resistance of the films deposited in pure argon are found to be 85-96% in the wavelength range 400-800 nm and 65 {Omega}/{open_square}, respectively.

14 SOLAR ENERGY↗