Search NASA⌕ Search

SEARCH · Search NASA

Results for “TENSILE STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Study of high performance alloy electroforming

Nickel-manganese electroformed specimens and nickel-cobalt-manganese samples were heat treated at 343 C (650 F) for comparison of room temperature ductility with that observed for alloys heat treated at 315.6C (600 F). All heat treatments were for 24 hours. This heat treatment temperature increase generally did not result in significant improvements in ductility. However, increases in yield strength - with slight decreases in tensile strengths - were noted for the nickel-manganese and nickel-cobalt-manganese alloys. For the case of employing fairly high manganese contents in the electrolyte and countering ensuing high tensile stress in the alloy by saccharin additions to the bath, it was noted that nickel-manganese alloys with over 0.4% by weight manganese retained high ultimate and yield strengths after the 343 C (650 F) heat treatment for 24 hours. Elongations were still lower than desired. For alloys with less than 0.4% by weight manganese this heat treatment provided excellent ductility, but very significant reductions in ultimate and yield strengths were noted.

Malone, G. A.↗
NASA NTRS1984

Elevated temperature compressive steady state deformation and failure in the oxide dispersion strengthened alloy MA 6000E

The compressive flow strength-strain rate behavior of the oxide-dispersion-strengthened alloy MA 6000E has been studied in the temperature range 1144-1366 K, with strain rates ranging from 2.1 x 10 to the -5th to 2.1 x 10 to the -7th per s. It is found that the inherent strength of the alloy is essentially the same in all test directions and that the low strength observed in tensile tests results from the inability of grain boundaries to support high tensile stresses. The failure of MA 6000E under high-temperature, slow plastic flow conditions is shown to be the result of concentrated slip. Slow plastic deformation in MA 6000E can be described by a threshold stress model of creep where threshold stresses are calculated from relatively fast testing procedures and the effective stress exponent for creep is assumed to be 3.5.

Whittenberger, J. D.↗
NASA NTRS1984

Creep of chemically vapor deposited SiC fibers

The creep, thermal expansion, and elastic modulus properties for chemically vapor deposited SiC fibers were measured between 1000 and 1500 C. Creep strain was observed to increase logarithmically with time, monotonically with temperature, and linearly with tensile stress up to 600 MPa. The controlling activation energy was 480 + or - 20 kJ/mole. Thermal pretreatments near 1200 and 1450 C were found to significantly reduce fiber creep. These results coupled with creep recovery observations indicate that below 1400 C fiber creep is anelastic with neglible plastic component. This allowed a simple predictive method to be developed for describing fiber total deformation as a function of time, temperature, and stress. Mechanistic analysis of the property data suggests that fiber creep is the result of beta-SiC grain boundary sliding controlled by a small percent of free silicon in the grain boundaries.

Dicarlo, J. A.↗
NASA NTRS1985

Origin of Martian Polygonal Terrain: Preliminary Results

The morphological characteristics of Martian polygonal terrain, and of the fractures defining the polygons were reviewed. The age relationships between the fractures defining the polygons and the material making up the polygonal terrain of Adamas Labyrinthus will be determined. This involves detailed mapping, with the relative ages of Key map units and the fractures determined by superposition and crater counts. The common occurrence of circular fracture patterns within the polygonal terrain is consistent with differential compaction over crater rims, and is easily accounted for by the tensile stresses that would be reasonably expected to occur in such places.

Mcgill, G. E.↗
NASA NTRS1984

Subcritical Fracture Propagation in Rocks: an Examination Using the Methods of Fracture Mechanics and Non-Destructive Testing

An experimental investigation of tensile rock fracture is presented with an emphasis on characterizing time dependent crack growth using the methods of fracture mechanics. Subcritical fracture experiments were performed in moist air on glass and five different rock types at crack velocities using the double torsion technique. The experimental results suggest that subcritical fracture resistance in polycrystals is dominated by microstructural effects. Evidence for gross violations of the assumptions of linear elastic fracture mechanics and double torsion theory was found in the tests on rocks. In an effort to obtain a better understanding of the physical breakdown processes associated with rock fracture, a series of nondestructive evaluation tests were performed during subcritical fracture experiments on glass and granite. Comparison of the observed process zone shape with that expected on the basis of a critical normal principal tensile stress criterion shows that the zone is much more elongated in the crack propagation direction than predicted by the continuum based microcracking model alone.

Swanson, P. L.↗
NASA NTRS1985

Fractography of the interlaminar fracture of carbon-fibre epoxy composites

The failed surfaces of interlaminar fracture (mode I) specimens of AS4/3501-6 were examined using scanning electron microscopy. The principal fracture features were fiber pull-out (bundles and single fibers), hackle markings, and regions of smooth resin fracture. Considerable (30 to 50 percent) relaxation of the deformed resin occurred when the specimens were heated above the matrix glass transition temperature. This relaxation was taken as evidence of extensive shear yielding of the resin during the fracture process. Some of the fractography features are discussed in terms of transverse tensile stresses and peeling stresses acting on the fibers. In some instances these localized stresses focus failure close to the resin-fiber interface, which can be mistakenly interpreted as interfacial failure and low fiber-resin adhesion.

Bascom, W. D.↗
NASA NTRS1985

A study of the applicability of nucleation theory to quasi-thermodynamic transitions of second and higher Ehrenfest-order

The applicability of classical nucleation theory to second (and higher) order thermodynamic transitions in the Ehrenfest sense has been investigated and expressions have been derived upon which the qualitative and quantitative success of the basic approach must ultimately depend. The expressions describe the effect of temperature undercooling, hydrostatic pressure, and tensile stress upon the critical parameters, the critical nucleus size, and critical free energy barrier, for nucleation in a thermodynamic transition of any general order. These expressions are then specialized for the case of first and second order transitions. The expressions for the case of undercooling are then used in conjunction with literature data to estimate values for the critical quantities in a system undergoing a pseudo-second order transition (the glass transition in polystyrene). Methods of estimating the interfacial energy gamma in systems undergoing a first and second order transition are also discussed.

Barker, R. E., Jr.↗
NASA NTRS1986

Creep of chemically vapour deposited SiC fibres

The creep, thermal expansion, and elastic modulus properties for chemically vapor deposited SiC fibers were measured between 1000 and 1500 C. Creep strain was observed to increase logarithmically with time, monotonically with temperature, and linearly with tensile stress up to 600 MPa. The controlling activation energy was 480 + or - 20 kJ/mole. Thermal pretreatments near 1200 and 1450 C were found to significantly reduce fiber creep. These results coupled with creep recovery observations indicate that below 1400 C fiber creep is anelastic with negligible plastic component. This allowed a simple predictive method to be developed for describing fiber total deformation as a function of time, temperature, and stress. Mechanistic analysis of the property data suggests that fiber creep is the result of beta-SiC grain boundary sliding controlled by a small percent of free silicon in the grain boundaries.

Dicarlo, J. A.↗
NASA NTRS1985

Nondestructive determination of mechanical properties

The sensitivity of the velocity of ultrasonic waves to the elasticity of the materials (acousto-elastic constant - AEC) as controlled by the microstructure of the materials was examined experimentally. Rolled-plate specimens of five different Al alloys were subjected to tensile tests while being monitored for the velocity change of a 10 MHz longitudinal wave as a function of the applied tensile stress. The acoustic propagation velocity was measured perpendicularly to the stress. Determinations were made of the yield strength and the hardnesses of the specimens. Samples of the plate materials examined microscopically to characterize the solid phases. The AECs varied linearly with the percentage of solid solution phase of the alloys. The trend for strain-hardened samples was, however, opposite from that in the precipitation-hardened alloys. The results underscore the necessity of considering the microstructural dependencies of the AECs when using ultrasonic NDE methods, and also opened the potential of determining some mechanical properties with NDE techniques.

Schneider, E.↗
NASA NTRS1988

A model for life predictions of nickel-base superalloys in high-temperature low cycle fatigue

Extensive characterization of low-cycle fatigue damage mechanisms was performed on polycrystalline Rene 80 and IN100 tested in the temperature range from 871 to 1000 C. Low-cycle fatigue life was found to be dominated by propagation of microcracks to a critical size governed by the maximum tensile stress. A model was developed which incorporates a threshold stress for crack extension, a stress-based crack growth expression, and a failure criterion. The mathematical equivalence between this mechanistically based model and the strain-life low-cycle fatigue law was demonstrated using cyclic stress-strain relationships. The model was shown to correlate the high-temperature low-cycle fatigue data of the different nickel-base superalloys considered in this study.

Romanoski, Glenn R.↗
NASA NTRS1989

TEM studies of oxidized NiAl and Ni3Al cross sections

Cross sections of oxide scale/(Ni-Al) intermetallics were prepared by a new method and studied using primarily TEM. The cross sections were prepared by encasing an oxidized metal specimen sandwich in a low-melting-temperature zinc alloy. Observations of oxidized zirconium-doped beta-NiAl cross sections revealed crystallographic voids beneath an adherent Al2O3 scale. The oxide-metal interface was incoherent, but a high dislocation density in the metal near the interface suggested that a large tensile stress was induced by the attached oxide scale. A duplex Al2O3-NiAl2O4 scale formed on zirconium-doped and zirconium/boron-doped gamma-prime-Ni3Al alloys. Additional results are presented involving oxidation mechanisms and oxide-metal interface structures.

Doychak, J.↗
NASA NTRS1990

Development of impact design methods for ceramic gas turbine components

Impact damage prediction methods are being developed to aid in the design of ceramic gas turbine engine components with improved impact resistance. Two impact damage modes were characterized: local, near the impact site, and structural, usually fast fracture away from the impact site. Local damage to Si3N4 impacted by Si3N4 spherical projectiles consists of ring and/or radial cracks around the impact point. In a mechanistic model being developed, impact damage is characterized as microcrack nucleation and propagation. The extent of damage is measured as volume fraction of microcracks. Model capability is demonstrated by simulating late impact tests. Structural failure is caused by tensile stress during impact exceeding material strength. The EPIC3 code was successfully used to predict blade structural failures in different size particle impacts on radial and axial blades.

Song, J.↗
NASA NTRS1990

InAs/Ga(1-x)In(x)Sb superlattices for infrared detector applications

The successful growth of InAs/Ga(1-x)In(x)Sb superlattices and their optical and structural characterization is discussed. Samples were grown by molecular beam epitaxy at fairly low substrate temperatures (less than 400 C). Structural quality was assessed by reflection high energy electron difrraction, transmission electron microscopy, and x ray diffraction. Excellent structures were achieved for growth on thick, strain relaxed GaSb buffer layers on GaAs substrates, despite a residual threading dislocation density of 10(exp 9)cm(exp -2) originating at the GaSb/GaAs interface. Despite a lattice mismatch of 1.7 percent, InAs/Ga(0.75)In(0.25)Sb superlattices are observed to be free of misfit dislocations at the thicknesses examined here, owing to the close lattice match between the superlattice and GaSb, which evenly distributes compressive and tensile stresses between the InAs and Ga(0.75)In(0.25)Sb layers. Photoluminescence and photoconductivity measurements indicate that the energy gaps of the strain-layer superlattices are smaller than those of InAs/GaSb superlattices with the same layer thicknesses, and are in agreement with the theoretical predictions of Smith and Mailhiot. Energy gaps of 80 to 250 meV (15 to 5 microns) have been measured for InAs/Ga(0.75)In(0.25)Sb superlattices with 45 to 25 A/25 A layer thickness. Results demonstrate that far-infrared cutoff wavelengths are compatible with the thin superlattice layers required for strong optical absorption in type-II superlattices.

Miles, Richard H.↗
NASA NTRS1990

Shape-memory properties in Ni-Ti sputter-deposited film

A Ni-Ti alloy, generically called nitinol, was prepared from sputtering targets of two different compositions on glass substrates using a dc magnetron source. The as-deposited films were amorphous in structure and did not exhibit a shape memory. The amorphous films were crystallized with a suitable annealing process, and the transformation properties were measured using differential scanning calorimetry. The annealed films demonstrated a strong shape-memory effect. Stress/strain measurements and physical manipulation were used to evaluate the shape recovery. These tests demonstrated sustained tensile stresses of up to 480 MPa in the high-temperature phase, and a characteristic plastic deformation in the low-temperature phase.

Busch, J. D.↗
NASA NTRS1991

High strain rate properties of off-axis composite laminates, part 2

Unidirectional off-axis graphite/epoxy and graphite/S-glass/epoxy laminates were characterized in uniaxial tension at strain rates ranging from quasi-static to over 500 s(sup -1). Laminate ring specimens were loaded by internal pressure with the tensile stress at 22.5, 30, and 45 degrees relative to the fiber direction. Results were presented in the form of stress-strain curves to failure. Properties determined included moduli, Poisson's ratios, strength, and ultimate strain. In all three laminates of both materials the modulus and strength increase sharply with strain rate, reaching values roughly 100, 150, and 200 percent higher than corresponding static values for the 22.5(sub 8), 30(sub 8), and 45(sub 8) degree laminates, respectively. In the case of ultimate strain no definite trends could be established, but the maximum deviation from the average of any value for any strain rate was less than 18 percent.

Daniel, I. M.↗
NASA NTRS1992

Environmental fatigue of an Al-Li-Cu alloy. Part 3: Modeling of crack tip hydrogen damage

Environmental fatigue crack propagation rates and microscopic damage modes in Al-Li-Cu alloy 2090 (Parts 1 and 2) are described by a crack tip process zone model based on hydrogen embrittlement. Da/dN sub ENV equates to discontinuous crack advance over a distance, delta a, determined by dislocation transport of dissolved hydrogen at plastic strains above a critical value; and to the number of load cycles, delta N, required to hydrogenate process zone trap sites that fracture according to a local hydrogen concentration-tensile stress criterion. Transgranular (100) cracking occurs for process zones smaller than the subgrain size, and due to lattice decohesion or hydride formation. Intersubgranular cracking dominates when the process zone encompasses one or more subgrains so that dislocation transport provides hydrogen to strong boundary trapping sites. Multi-sloped log da/dN-log delta K behavior is produced by process zone plastic strain-hydrogen-microstructure interactions, and is determined by the DK dependent rates and proportions of each parallel cracking mode. Absolute values of the exponents and the preexponential coefficients are not predictable; however, fractographic measurements theta sub i coupled with fatigue crack propagation data for alloy 2090 established that the process zone model correctly describes fatigue crack propagation kinetics. Crack surface films hinder hydrogen uptake and reduce da/dN and alter the proportions of each fatigue crack propagation mode.

Piascik, Robert S.↗
NASA NTRS1992

Diffusive crack growth at a bimaterial interface

The diffusional microcrack growth behavior in a bimaterial system is investigated with an aim at estimating service life of advanced ceramic composites under creep-rupture conditions. The crack is assumed to grow via a coupled surface and grain-boundary diffusion under steady state conditions. The tensile stress distribution along the interface ahead of the moving crack tip is solved, and it is found that a new length parameter exists as a scaling factor for which the solution becomes identical to the single phase case when plotted on the nondimensional physical plane. In contrast to the elastic stress solution which shows singularity at the tip, together with oscillatory character away from the tip, the creep stresses have a peak value away from the tip due to a wedging effect and interfacial sliding eliminates stress oscillation resulting in a decoupling between mode I and mode II loading. This solution ties the far-field loading parameter to the crack tip conditions in terms of the unknown crack velocity to give a specific V-K(1) relationship. It is shown that an exponent of 12 in the conventional crack growth power law emerges at the higher applied stress range.

Chuang, Tze-Jer↗
NASA NTRS1992

Failure mechanisms of 3-D woven SiC/SiC composites under tensile and flexural loading at room and elevated temperatures

Nicalon silicon carbide 3D yarn with silicon carbide matrix composites made through a chemical vapor infiltration (CVI) process were investigated under tensile and flexural loading at 23, 1200 and 1550 C in air. The effectiveness of a chemical vapor deposition (CVD) SiC surface coating was also evaluated in severe oxidizing environment. Acoustic emission sensors and in situ optical microscopy were used at room temperature to monitor the failure mechanisms. It is shown that the level of tensile stress at which nonlinear behavior begins is not drastically reduced at 1200 and 1550 C when composites were protected by a SiC surface coating. Extensive fiber pull-out was observed only in the 1550 C specimen. Similar behaviors were also found in flexural specimens.

Chulya, Abhisak↗