SEARCH · Search NASA

Results for “Trailing edges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Aerodynamic Load Analysis of a Variable Camber Continuous Trailing Edge Flap System on a Flexible Wing Aircraft

This paper presents an investigative aerodynamic analysis conducted on the novel control surface known as a Variable Camber Continuous Trailing Edge Flap (VCCTEF). The VCCTEF is modeled as a control effector on the NASA Generic Transport Model (GTM) where wing flexibility is considered. Aerodynamic modeling of the aircraft is conducted using vortex-lattice method (VLM), and an aeroelastic model of the aircraft that utilizes a coupled finite-element analysis (FEA) vortex-lattice solution is employed. VLM solutions are used to determine quasi-steady aerodynamic loading over the aeroelastic wing structures with VCCTEF. The load data is used to calculate aerodynamic sensitivities to control surface deployment and is also integrated to determine overall hinge moments. This analysis is conducted for different flight conditions, where control sensitivities compare the VCCTEF effectiveness against conventional control surfaces. Hinge moment results provide insight into aeroelastic wing loads, and worst case hinge moments for the VCCTEF can be estimated. Results show that the VCCTEF offers greater control authority than conventional ailerons at cruise, and nominal flap settings are determined for a low-speed take-off condition where the VCCTEF maintains comparable control effectiveness. Worst case hinge moment values are presented, where for a possible VCCTEF configuration, the stiff wing model demonstrates up to a 5.90 percent increase in flap hinge moment relative to a rigid model, and a reduced stiffness model demonstrates up to an 11.42 percent increase.

Aeroelasticity↗

NASA NTRS1994

Vibration reduction in helicopter rotors using an actively controlled partial span trailing edge flap located on the blade

This report describes an analytical study of vibration reduction in a four-bladed helicopter rotor using an actively controlled, partial span, trailing edge flap located on the blade. The vibration reduction produced by the actively controlled flap (ACF) is compared with that obtained using individual blade control (IBC), in which the entire blade is oscillated in pitch. For both cases a deterministic feedback controller is implemented to reduce the 4/rev hub loads. For all cases considered, the ACF produced vibration reduction comparable with that obtained using IBC, but consumed only 10-30% of the power required to implement IBC. A careful parametric study is conducted to determine the influence of blade torsional stiffness, spanwise location of the control flap, and hinge moment correction on the vibration reduction characteristics of the ACF. The results clearly demonstrate the feasibility of this new approach to vibration reduction. It should be emphasized than the ACF, used together with a conventional swashplate, is completely decoupled from the primary flight control system and thus it has no influence on the airworthiness of the helicopter. This attribute is potentially a significant advantage when compared to IBC.

Millott, T. A.↗

NASA NTRS1947

The Effectiveness at High Speeds of a 20-Percent-chord Plain Trailing-edge Flap on the NACA 65-210 Airfoil Section

An analysis has been made of the lift-control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flag on the INCA 65-210 airfoil section.

Stivers, Louis S., Jr.↗

NASA NTRS1972

Prediction of unsteady aerodynamic loadings caused by trailing edge control surface motions in subsonic compressible flow: Computer program description

A digital computer program has been developed to calculate unsteady loadings caused by motions of lifting surfaces with trailing edge control based on the subsonic kernal function approach. The pressure singularities at hinge line and side edges have been extracted analytically as a preliminary step to solving the integral by collocation. The program calculates generalized aerodynamic forces for user supplied deflection modes. Optional intermediate output includes pressure at an array of points, and sectional generalized forces. From one to four controls on the half span can be accommodated.

Redman, M. C.↗

NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft with Variable-Camber Continuous Trailing-Edge Flap

This paper presents an aeroelastic trim drag optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with the Variable-Camber Continuous Trailing-Edge Flap (VCCTEF). An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to finite-element code BEAM3D is developed to provide a rapid aircraft aeroelastic performance evaluation. The VSPAERO model has been validated against wind tunnel test data. Aeroelastic trim drag optimization studies are conducted for a VCCTEF configuration with 6-spanwise sections. Three different flight conditions corresponding to Mach 0.745 are selected for the TTBW aircraft aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized VCCTEF deflection achieves a drag reduction of about 9.1 counts, 5.9 counts, and 11.8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the aeroelastic trim drag optimization.

Aeroelastic trim drag↗

NASA NTRS1981

Mean-flow and turbulence measurements in the vicinity of the trailing edge of an NACA (63 sub 1)-012 airfoil

The Langley aircraft noise reduction laboratory was used to measure mean flow and turbulence in the vicinity of a cusped-trailing edge of two dimensional NACA 631-012 airfoil at zero angle of attack. Naturally transitioned flow and artificially tripped flow were investigated. Flow regions studied include the boundary layer and the near wake. Measurements were made at a free stream Reynolds number based on airfoil chord of 1.25 x 10 to the 6th power and a free stream Mach number of 0.1. Distributions of streamwise mean velocity, integral properties of the mean flow, turbulent intensities, and Reynolds shear stress are reported. For the naturally transitioned flow, the general trends observed are similar to those reported for a fully developed turbulent boundary layer over a flat plate under zero pressure gradient, with the exception of the notable streamwise variations in the turbulence properties for the airfoil flow. The main effect of flow tripping is to eliminate these streamwise variations. Observed changes in the mean flow and turbulence fields caused by tripping are expected on the basis of the Reynolds number based on the boundary layer thickness.

Yu, J. C.↗

NASA NTRS1992

Serrated trailing edges for improving lift and drag characteristics of lifting surfaces

An improvement in the lift and drag characteristics of a lifting surface is achieved by attaching a serrated panel to the trailing edge of the lifting surface. The serrations may have a saw-tooth configuration, with a 60 degree included angle between adjacent serrations. The serrations may vary in shape and size over the span-wise length of the lifting surface, and may be positioned at fixed or adjustable deflections relative to the chord of the lifting surface.

Vijgen, Paul M. H. W.↗

NASA NTRS1933

The effect of multiple fixed slots and a trailing-edge flap on the lift and drag of a Clark Y airfoil

Lift and drag tests were made on a Clark Y wing equipped with four fixed slots and a trailing-edge flap in the 5-foot vertical wind tunnel of the National Advisory Committee for Aeronautics. All possible combinations of the four slots were tested with the flap neutral and the most promising combinations were tested with the flap down 45 degrees. Considering both the maximum lift coefficient and the speed-range ratio with the flap neutral no appreciable improvement was found with the use of more than the single leading-edge slot. With the flap down 45 degrees a maximum lift coefficient of 2.60 was obtained but the particular slot combination used had a rather large minimum drag coefficient with the flap neutral. With the flap down 45 degrees the optimum combination, considering both the maximum lift coefficient and the speed-range ratio, was obtained with only the two rearmost slots in use. For this arrangement the maximum lift coefficient was 2.44.

Weick, Fred E↗

NASA NTRS1972

Prediction of unsteady aerodynamic loadings caused by trailing edge control surface motions in subsonic compressible flow: Analysis and results

A theoretical analysis and a computer program have been developed for the prediction of unsteady lifting surface loadings caused by motions of trailing edge control surfaces having sealed gaps. The final form of the downwash integral equation has been formulated by isolating the singularities from the non-singular terms and establishing a preferred solution process to remove and evaluate the downwash discontinuities in a systematic manner. Comparisons of theoretical and experimental pressure data are made for several control surface configurations. The comparisons indicate that reasonably accurate theoretical pressure distributions and generalized forces may be obtained for a wide variety of control surface configurations. Spanwise symmetry or antisymmetry of motion, and up to four control surfaces on each half span can be accommodated.

Rowe, W. S.↗

NASA NTRS1985

On the application of a hairpin vortex model of wall turbulence to trailing edge noise prediction

The goal is to develop a technique via a hairpin vortex model of the turbulent boundary layer, which would lead to the estimation of the aerodynamic input for use in trailing edge noise prediction theories. The work described represents an initial step in reaching this goal. The hairpin vortex is considered as the underlying structure of the wall turbulence and the turbulent boundary layer is viewed as an ensemble of typical hairpin vortices of different sizes. A synthesis technique is examined which links the mean flow and various turbulence quantities via these typical vortices. The distribution of turbulence quantities among vortices of different scales follows directly from the probability distribution needed to give the measured mean flow vorticity. The main features of individual representative hairpin vortices are discussed in detail and a preliminary assessment of the synthesis approach is made.

Liu, N. S.↗

NASA NTRS2003

Predicting Modes of the Unsteady Vorticity Field near the Trailing Edge of a Blade

Progress on predicting modes of the unsteady velocity/vorticity field of a turbulent boundary layer from Reynolds stress statistics is described. Prediction of these modes, that provide the source terms for trailing edge noise predictions in aircraft engine fans and other configurations, will allow for the first time detailed viscous flow effects to be included in such noise calculations. The key accomplishments of this work in FY02 are: (1) The development of a Matlab code for the prediction of modes in two- and three-dimensional boundary layers, previously applied to plane wakes; (2) Predictions with the code using a constant lengthscale formulation in a fully developed turbulence channel flow. Comparison of these boundary layer predictions with available DNS simulation results; and (3) Formulation of an improved model using a variable lengthscale proportional to mixing length. Turbulent channel flow predictions and comparison with DNS results. This work is being carried out in continuous communication and collaboration with the Glegg research group at Florida Atlantic University, which will be incorporating mode predictions into engine noise calculations.

Devenport, William J.↗

NASA NTRS2018

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗

NASA NTRS1936

Investigation of Full-Scale Split Trailing-Edge Wing Flaps with Various Chords and Hinge Locations

This report gives the results of an investigation conducted in the NACA full-scale wind tunnel on a small parasol monoplane equipped with three different split trailing-edge wing flaps. The object of the investigation was to determine and correlate data on the characteristics of the airplane and flaps as affected by variation in flap chord, flap deflection, and flap location along the wing chord. The results give the lift, the drag, and the pitching moment characteristics of the airplane, and the flap forces and moments, the pressure distribution over the flaps and wing at one section, and the downwash characteristics of the flap and wing combinations.

Wallace, Rudolf↗

NASA NTRS1982

Prediction of separated asymmetric trailing-edge flows at transonic Mach numbers

Numerical simulations of the time-dependent, Reynolds averaged, Navier-Stokes equations, employing various eddy viscosity turbulence models, are presented and compared with measurements from an investigation of a transonic trailing-edge flow at a high Reynolds number. Comparisons are made for mean surface quantities as well as mean and fluctuating flow-field quantities. Solutions employing two-equation turbulence models correctly predict all the major features of the flow field. Viscous-inviscid interaction effects were found to be extremely important for predicting this flow field and equally important to the turbulence modeling employed.

Horstman, C. C.↗

NASA NTRS1975

Cold-air experimental investigation of a turbine with blade trailing edge coolant ejection. 1: Single-stage turbine

Tests were made on a 0.762-meter-tip-diameter research turbine to determine the effect of blade coolant flow on its aerodynamic performance. Both stator and rotor blades had trailing-edge slots for coolant ejection. The turbine was tested over a range of speed and pressure ratio. High primary efficiencies, calculated on the basis of primary air only, were obtained. The efficiency attained was identical to that reported for the turbine from a previous investigation were only slotted stator blades where incorporated in the turbine and tested. And it also compares with results for the turbine with solid blading. Independently varying the rotor coolant flow showed that rotor cooling imposed a severe penalty on turbine efficiency. The thermodynamic efficiency, which accounts for the ideal energies of both blade coolant flows, decreased linearly with rotor coolant at a rate of about 0.7 percent per percent rotor coolant fraction.

Schum, H. J.↗

NASA NTRS1986

An overview of some investigations of pressure and thermal distributions induced by trailing edge controls on hypersonic aircraft

Detailed surface heat transfer and pressure distributions have been obtained in three-dimensional shock-wave boundary-layer interactions flow regions. The data described were obtained on fundamental shapes: planar wings with trailing edge flaps or spoilers and planar or cylindrical center bodies, representative of the aft portion of hypersonic aircraft. An overview of the work is presented; details of the projects are available in many reports in the open literature. Analytic, empiric methods are advanced for predicting the extent of separation and the increased heat transfer and pressure loads in three-dimensional separated flow regions.

Kaufman, Louis G., II↗

NASA NTRS2018

Active Flow Control for Trailing Edge Flap Separation

Active flow control (AFC) in the form of sweeping jet (SWJ) excitation and discrete steady jet excitation is used to control the flow separation on an NACA 0015 semispan wing with a deflected, simple-hinged, trailing edge flap. This geometry has been the focus of several recent publications that investigated methods to improve the efficiency of sweeping jet actuators. In the current study, the interaction of the AFC excitation with the separated flowfields present at several flap deflection angles was examined. Previous studies with this model have been limited to a maximum flap deflection angle of 40°. The flap deflection range was extended to 60! because systems studies have indicated that a high-lift system with simple-hinged flaps may require larger flap deflections than the Fowler flaps found on most high-lift systems. The results obtained at flap deflection angles of 20°, 40°, and 60° are presented and compared. Force and moment data, Particle Image Velocimetry (PIV) data, and steady and unsteady surface pressure data are used to describe the flowfield with and without AFC. With a flap deflection of 60°, increasing the SWJ actuator momentum at the flap shoulder increased lift due to an increase in circulation but did not completely eliminate the recirculation region above the flap surface. AFC using the discrete steady jet actuators of this study increased lift as well but required more mass flow than the SWJ actuators and had a detrimental effect on lift at the highest mass flow level tested. PIV results showed that the angle between the excitation and the flap surface was not optimal for attaching the separated shear layer.

Melton, LaTunia Pack↗

NASA NTRS1985

Massive separation and dynamic stall on a cusped trailing-edge airfoil

The cross-over from a predominantly attached two-dimensional flow to the bluff body form of separation is modeled via the interacting boundary layer approximation. The initial breakdown of the predominantly attached flow on a cusped trailing edge airfoil is examined using the Hilbert integral form of the unsteady interacting boundary layer equations. In addition, an interacting boundary layer technique is developed for calculating bluff body separation. This new model eliminates the severe scaling problems associated with bluff body separation through the use of a realistic inviscid eddy model, based on the infinite eddy Kirchhoff free-streamline description of separation. Brief consideration is given to the cross-over from bluff body separation to a predominantly attached flow, the extension to finite eddies and cascade flows, and the possible coupling with full, or parabolized, Navier-Stokes calculations.

Rothmayer, A. P.↗