Search NASA⌕ Search

SEARCH · Search NASA

Results for “VARIABLE SWEEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Effects of Sweep and Thickness on the Static Longitudinal Aerodynamic Characteristics of a Series of Thin, Low-aspect-ratio, Highly Tapered Wings at Transonic Speeds : Transonic-bump Method

An investigation by the transonic-bump technique of the static longitudinal aerodynamic characteristics of a series of thin, low-aspect-ratio, highly tapered wings has been made in the Langley high-speed 7- by 10-foot tunnel. The Mach number range extended from about 0.60 to 1.18, with corresponding Reynolds numbers ranging from about 0.75 x 10(6) to 0.95 x 10(6). The angle of attack range was from -10 degrees to approximately 32 degrees.The effects on drag and lift-drag ratio of a variation in sweep angle from -14.03 degrees to 45 degrees with respect to the quarter-chord line for wings of 3-percent-chord thickness was found to be small in comparison to the effects of a variation in thickness from 2 percent chord to 4.5 percent chord for wings with 14.03 degree sweepback. For the range of variables considered, variations in plan form were considerably more important with regard to longitudinal stability characteristics than the variations in thickness. For the series of basic wings having an aspect ratio of 4, the most hearly linear pitching-moment characteristics were obtained with 26.57 degree of sweepback of the quarter-chord line. However, for the modified series of wings (obtained by clipping the tips of the original wings parallel to the plane of symmetry to give an aspect ratio of 3 and a taper ratio of 0.143), the most nearly linear pitching-moment characteristics were obtained with 36.87 degrees of sweepback. By decreasing the thickness-to-chord ratios from 0.03 to 0.02, a large increase in lift-curve slope was obtained for both the basic and modified wings. All of the wings of both series had fairly large inward shifts of the lateral center-of-pressure location (indicative of tip stalling) with increasing lift coefficient, except those wings having minimum sweepback angles.

Fournier, Paul G↗
NASA NTRSDate not supplied

Design Exploration of a Slotted-Wing Common Research Model

A knowledge-based aerodynamic design method, Constrained Direct Iterative Surface Cur-vature (CDISC), has been leveraged for the computational design exploration of a Common Research Model with Reduced-Sweep and Slotted Wings (CRMRS-SW). Cruise-slotted-wing airfoils include a slot near the trailing edge of a main airfoil component to introduce stream air to the low-momentum, upper-surface boundary layer on a flap airfoil component with the goal of allowing for a more aft loading, relative to supercritical airfoils, without shock-induced separation. Ultimately, the cruise slotted wing is a passive technology that allows for an in-crease in the drag divergence Mach number and/or an increase in aerodynamic efficiency at agiven cruise condition. These aerodynamic benefits may be realized at the vehicle level through a trade space that includes the following design options: increasing cruise Mach number, in-creasing wing thickness, decreasing wing sweep, increasing lift coefficient and/or decreasing drag coefficient. The present study aimed to evaluate the slotted-wing concept’s potential as adrag-saving technology in application to a single-aisle transonic transport aircraft at a given cruise condition. The CDISC design method was used to develop a better understanding of the slotted-wing design variables that have a significant impact on the variability in aircraft drag and leverage this newly-developed knowledge to quantify the aerodynamic performance benefits enabled by the cruise slotted wing.

Brett R. Hiller↗
DOE OSTI2024

Experimental Investigation of the Effect of Air-Handling and DME-Propane Blends on the Performance and Emissions of a 4-Cylinder CI Engine

Dimethyl ether (DME) is considered an excellent alternative to diesel because of its higher cetane number and lower carbon content. Additionally, DME can be blended with abundantly available propane with minimal modifications to the propane infrastructure. This paper focuses on an experimental investigation of the effect of air-handling i.e., boost pressure and exhaust gas recirculation (EGR), and DME-propane blends on the combustion and emissions performance of a light-duty, four-cylinder, compression ignition (CI) engine. Here, the boost pressure and EGR sweeps were carried out and showed that higher boost pressures resulted in increased brake thermal efficiencies (BTE) at the expense of higher NOx emissions which could be reduced by an increase in EGR. The fuel sweeps were carried out at 0, 15 and 25% propane (neat, 85% and 75% DME) with 0% and 25% EGR. The fuel sweeps indicated that the ignition delay (ID) increased and burn duration (BD) decreased monotonically when the blend increased to 25% propane/75% DME. The results suggest optimum engine performance with neat DME at 105 kPa boost pressure and 25% EGR with propane addition improving the BTE with negligible increase in emissions. Higher contents of Propane, up to 25%, did not affect the variability of combustion, with standard deviations of burn duration and peak cylinder pressures below 1% for all test cases.

air-handling↗
NASA NTRS2000

Improving Tiltrotor Whirl-Mode Stability with Rotor Design Variations

Further increases in tiltrotor speeds are limited by coupled wing/rotor whirl-mode aeroelastic instability. Increased power, thrust, and rotor efficiency are not enough: the whirl-mode stability boundary must also be improved. With current technology, very stiff, thick wings of limited aspect ratio are essential to meet the stability requirements, which severely limits cruise efficiency and maximum speed. Larger and more efficient tiltrotors will need longer and lighter wings, for which whirl-mode flutter is a serious design issue. Numerous approaches to improving the whirl-mode airspeed boundary have been investigated, including tailored stiffness wings, active stability augmentation, variable geometry rotors, highly swept tips, and at one extreme, folding rotors. The research reported herein began with the much simpler approach of adjusting the chordwise positions of the rotor blade aerodynamic center and center of gravity, effected by offsetting the airfoil quarter chord or structural mass with respect to the elastic axis. The research was recently extended to include variations in blade sweep, control system stiffness, and pitch-flap coupling (delta(sub 3)). As an introduction to the subject, and to establish a baseline against which to measure stability improvements, this report will first summarize results. The paper will then discuss more advanced studies of swept blades and control-system modifications.

Acree, C. W., Jr.↗
NASA NTRS1993

Reduction of structural loads using maneuver load control on the Advanced Fighter Technology Integration (AFTI)/F-111 mission adaptive wing

A transonic fighter-bomber aircraft, having a swept supercritical wing with smooth variable-camber flaps was fitted with a maneuver load control (MLC) system that implements a technique to reduce the inboard bending moments in the wing by shifting the spanwise load distribution inboard as load factor increases. The technique modifies the spanwise camber distribution by automatically commanding flap position as a function of flap position, true airspeed, Mach number, dynamic pressure, normal acceleration, and wing sweep position. Flight test structural loads data were obtained for loads in both the wing box and the wing root. Data from uniformly deflected flaps were compared with data from flaps in the MLC configuration where the outboard segment of three flap segments was deflected downward less than the two inboard segments. The changes in the shear loads in the forward wing spar and at the roots of the stabilators also are presented. The camber control system automatically reconfigures the flaps through varied flight conditions. Configurations having both moderate and full trailing-edge flap deflection were tested. Flight test data were collected at Mach numbers of 0.6, 0.7, 0.8, and 0.9 and dynamic pressures of 300, 450, 600, and 800 lb/sq ft. The Reynolds numbers for these flight conditions ranged from 26 x 10(exp 6) to 54 x 10(exp 6) at the mean aerodynamic chord. Load factor increases of up to 1.0 g achieved with no increase in wing root bending moment with the MLC flap configuration.

Thornton, Stephen V.↗
NASA NTRS1967

Matrix Analysis of Longitudinal and Torsional Vibrations in Nonuniform Multibranch Beams

Since longitudinal modes and frequencies provide basic data for dynamic analyses of arbitrary beam-like structures and since closed-form solutions for the modes are generally not feasible to obtain, an approximate method is developed for computing the natural frequencies and the corresponding mode shapes for a variable-section, unconstrained multibranch beam. A lumped mass analogy employing influence coefficients is used to represent the beam. The simultaneous equations of motion for the lumped mass system are derived in matrix form and algebraically manipulated to yield a classical eigenvalue equation solvable by standard procedures. The orthogonality relationship of the natural modes is derived and used to form the basis of an orthogonal sweeping process for determination of modes above the fundamental. Numerical examples including an application to a solid-fuel launch system are presented. Also, a detailed discussion is devoted to the theoretical verifications of the approximate modes and frequencies.

Wingate, Robert T.↗
NASA NTRS1993

Reynolds number influences in aeronautics

Reynolds number, a measure of the ratio of inertia to viscous forces, is a fundamental similarity parameter for fluid flows and therefore, would be expected to have a major influence in aerodynamics and aeronautics. Reynolds number influences are generally large, but monatomic, for attached laminar (continuum) flow; however, laminar flows are easily separated, inducing even stronger, non-monatomic, Reynolds number sensitivities. Probably the strongest Reynolds number influences occur in connection with transitional flow behavior. Transition can take place over a tremendous Reynolds number range, from the order of 20 x 10(exp 3) for 2-D free shear layers up to the order of 100 x 10(exp 6) for hypersonic boundary layers. This variability in transition behavior is especially important for complex configurations where various vehicle and flow field elements can undergo transition at various Reynolds numbers, causing often surprising changes in aerodynamics characteristics over wide ranges in Reynolds number. This is further compounded by the vast parameterization associated with transition, in that any parameter which influences mean viscous flow development (e.g., pressure gradient, flow curvature, wall temperature, Mach number, sweep, roughness, flow chemistry, shock interactions, etc.), and incident disturbance fields (acoustics, vorticity, particulates, temperature spottiness, even electro static discharges) can alter transition locations to first order. The usual method of dealing with the transition problem is to trip the flow in the generally lower Reynolds number wind tunnel to simulate the flight turbulent behavior. However, this is not wholly satisfactory as it results in incorrectly scaled viscous region thicknesses and cannot be utilized at all for applications such as turbine blades and helicopter rotors, nacelles, leading edge and nose regions, and High Altitude Long Endurance and hypersonic airbreathers where the transitional flow is an innately critical portion of the problem.

Bushnell, Dennis M.↗
DOE OSTI2026

Metal additively manufactured wavy fin cold-plate architecture for improved thermal-hydraulic performance

Rapid growth in artificial intelligence and data center workloads demands high-performance liquid cooling to manage increasing chip power. This study presents two metal-additive-manufactured cold plates with sinusoidal fins, constant-amplitude wavy fins and linearly variable-amplitude wavy fins and compares them against metal-additive-manufactured straight fins using experiments conducted at 1 kW heat dissipation as well as high-fidelity 3D conjugate computational fluid dynamic simulations. The cold plates were printed in AlSi10Mg material and underwent design using a Python-automated workflow prior to manufacture and testing. The experiments show that wavy fins reduce the normalized thermal resistance by 35 to 45 % at water flow rates from 1 to 4 LPM. At a fixed 20 kPa pressure drop, the variable-waviness design lowered peak surface temperature by 9 °C and thermal resistance by 51 %, while edge-channel maldistribution in the constant wavy fin design limited gains. A thermal resistance breakdown revealed that 55–63 % of the total thermal resistance in wavy designs comes from base heat conduction, 27–33 % from fin heat conduction, and 9–13 % from fin heat convection, indicating the need to address conduction bottlenecks. Parametric sweeps identify a 3 mm fin pitch as optimal, and that horizontal inlet/outlet manifolds further reduce pressure drop by 30–60 % and thermal resistance by 9–16 % relative to vertical inlet-outlet manifolds. The results yield comprehensive guidelines for fin geometry, manifold alignment, material selection and additive-manufacturing constraints to realize high-performance liquid-cooled cold plates for power-dense electronics.

3d printing↗
NASA NTRS1971

Infrared spectrometry studies: Spectral digital data acquisition system (1971 version)

The construction of the Stanford Spectral Digital Data Acquisition System is described. The objective of the system is to record both the spectral distribution of incoming radiation from the rock samples measured by the spectroradiometer (Exotech Model 10-34 Circular Variable Filter Infrared Spectroradiometer) together with other weather information. This system is designed for both laboratory and field measurement programs. The multichannel inputs (8 channels) of the system are as follows: Ch 1 the Spectro-radiometer, Ch 2 the radiometer (PRT-5), and Ch 3 to Ch 8 for the weather information. The system records data from channel 1 and channel 2 alternately for 48 times, before a fast sweep across the six weather channels, to form a single scan in the scan counter. The operation is illustrated in a block diagram, and the theory of operation is described. The outputs are written on a 7-track magnetic tape with IBM compatible form. The format of the tape and the playback computer programs are included. The micro-pac digital modules and a CIPHER model 70 tape recorder (Cipher Data Products) are used. One of the major characteristics of this system is that it is externally clocked by the spectroradiometer instead of taking data at intervals of various wavelengths by using internal-clocking.

Lu, L.↗
NASA NTRS2012

Parametric Deformation of Discrete Geometry for Aerodynamic Shape Design

We present a versatile discrete geometry manipulation platform for aerospace vehicle shape optimization. The platform is based on the geometry kernel of an open-source modeling tool called Blender and offers access to four parametric deformation techniques: lattice, cage-based, skeletal, and direct manipulation. Custom deformation methods are implemented as plugins, and the kernel is controlled through a scripting interface. Surface sensitivities are provided to support gradient-based optimization. The platform architecture allows the use of geometry pipelines, where multiple modelers are used in sequence, enabling manipulation difficult or impossible to achieve with a constructive modeler or deformer alone. We implement an intuitive custom deformation method in which a set of surface points serve as the design variables and user-specified constraints are intrinsically satisfied. We test our geometry platform on several design examples using an aerodynamic design framework based on Cartesian grids. We examine inverse airfoil design and shape matching and perform lift-constrained drag minimization on an airfoil with thickness constraints. A transport wing-fuselage integration problem demonstrates the approach in 3D. In a final example, our platform is pipelined with a constructive modeler to parabolically sweep a wingtip while applying a 1-G loading deformation across the wingspan. This work is an important first step towards the larger goal of leveraging the investment of the graphics industry to improve the state-of-the-art in aerospace geometry tools.

Anderson, George R.↗
NASA NTRS2020

Evaluation of Tablet-Based Methods for Assessment of Contrast Sensitivity

Some astronauts have suffered degradation of vision during long-duration space flight, suffering from a condition that has come to be known as Spaceflight Associated Neuro-ocular Syndrome (SANS). While related morphological changes can be observed with imaging technologies such as optical coherence tomography (OCT), it may be useful to have a rapid method for functional vision assessment. In this paper, we compare three tablet-based methods for rapid assessment of contrast sensitivity. First, a relatively novel method developed expressly for touch screens, in which the subject ”swipes” a frequency/contrast sweep grating to indicate the boundary between visible and invisible patterns; second, a method-of-adjustment task in which the subject adjusts the contrast of a grating patch up and down to bracket the visual threshold; and third, a traditional temporal two-alternative forced choice (2AFC) task, in which the subject is presented with a near-threshold stimulus in one of two intervals, and must report the interval containing the stimulus. The swipe method shows variability comparable to the 2AFC method, and shows good agreement in estimates of the spatial frequency of peak sensitivity. The absolute sensitivity estimated with the swipe method is higher than that of the other methods, perhaps because subjects are biased to trace outside of the visible pattern region, or perhaps due to stimulus differences.

Mulligan, Jeffrey B.↗
NASA NTRSDate not supplied

FUN3D Analyses in Support of the 1st AIAA Stability and Control Prediction Workshop

The 1st AIAA Stability and Control Prediction Workshop was created to establish best practices for the prediction of stability & control derivatives using computational fluid dynamics and assess the limitations of these computational methods when those best practices are applied. The inaugural workshop considers the ONERA version of the NASA/Boeing Common Research Model(CRM), which includes the wing, body, horizontal tail, and a vertical tail designed by ONERA. Wind tunnel tests have been conducted for this configuration with longitudinal tests having been previously published, in addition to unpublished data at small sideslip angles that will serve as ‘blind’ data for workshop data comparisons. Participants were provided a ‘family’ of unstructured grids for the full-span ONERA CRM model with the wind-tunnel sting included. This family of mixed-element grids consists of 5 levels of refinement (tiny, coarse, medium, fine, and extra fine) with surface and volume mesh scaling, resulting in a size range of 14.6 to 53.4 million nodes. In addition, a medium refinement mesh has been provided for the ONERA CRM configuration without a sting to evaluate the sting’s impact on static longitudinal stability characteristics. In addition to these workshop-provided grids, the present work also considers an equivalent ‘family’ of computational grids generated using Heldenmesh™, a rapid grid generation software by Helden Aerospace Corporation for creating high-quality, three-dimensional, mixed-element unstructured meshes. Because of the authors’ familiarity with this software, these additional grids were generated as a comparison to the workshop-provided grids and to better understand the implications of using volume-mirrored grids for stability and control predictions. The present work will contribute to the workshop with test case data generated using the NASA FUN3D code, a parallelized, unstructured, node-based, finite-volume discretization, Reynolds-averaged Navier-Stokes flow solver. Numerical simulations will be conducted using the Quadratic Constitutive Relationship (QCR) version of the Spalart-Allmaras (SA) turbulence model with negative turbulence variable provisions. Both steady and2nd-order, time-accurate simulation results are to be generated and compared for select test cases, as time permits, to investigate their impact on FUN3D predictions. The present work will consider the three primary workshop test cases: (1) grid convergence study, (2) Mach number effect on static stability, and (3) wind tunnel sting increments. Additionally, data will be provided for the two optional test cases, which include:(1) static stability derivative calculations and (2)sideslip angle sweeps. In each of the test cases, the vehicle is stationary, and the body is assumed to be rigid, where vehicle deformation has been accounted for in the model configuration geometry. For all test cases, longitudinal and lateral force and moment aerodynamic coefficients will be provided for the total configuration, in addition to a component-level breakdown that includes the port wing, starboard wing, fuselage, and tail.

CFD↗
NASA NTRS1990

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗
NASA NTRSDate not supplied

The Lunar Explorer Instrument for Space Biology Applications (LEIA) Pre-Flight Tests: Mechanical Considerations​

The BioSensor payload on the upcoming LEIA platform aboard the CLPS (CP-22) lander will carry yeast to the Moon's south pole to study the effects of lunar radiation and gravity. From Earth, BioSensor will transport desiccated yeast within 16 fluidic cards, each containing 16 fluidic wells of 100 microliters volume. At the start of the experiment, these microbes will be autonomously rehydrated on the Moon, and optical absorbance measurements at three wavelengths will be performed across all 256 wells. Absorbance measurements in fluidic wells are susceptible to noise and artifacts due to bubble formation during well rehydration and microbial growth. BioSensor, as a biofluidics system, faces significant data anomalies caused by payload vibrations, particularly from the operation of the co-located PROSPECT’s ProSEED drill, to assess lunar resources by penetrating the subsurface. To evaluate the impact of drill vibrations, fully assembled and filled fluidic cards were subjected to sine sweep signals in the x, y, z planes, ranging from 5 - 2560 Hz at g-loads of 0.25 and 0.5, with on-board accelerometer for localized vibration measurement. Wells with various fill conditions, including partial fills with different bubble sizes and completely filled wells, were tested. Results indicated that small bubbles adhered to well walls at high frequencies but were dislodged at low frequencies, causing data anomalies. Medium and large bubbles exhibited higher interference with optical data due to lower surface tension and variable bubble surface flexion. Overall, it was found that irrespective of the fill type, low-frequency vibrations were most detrimental to optical readings. Understanding the drill schedule and correlating it with BioSensor timestamps will help identify periods when BioSensor data is unreliable, a crucial step for accurately interpreting the microbial response data and ensuring the validity of the BioSensor's scientific measurements on the lunar surface.

Chinmayee Govinda Raj↗
DOE OSTI2025

Two-Dimensional Silk Crystal Films as Matrix Layer for High-Performance Microelectronics

This study explores a bio-inspired approach for memristive devices by combining Keggin-type polyoxometalates (POMs)-[SiW 12 O 40 ] 4 (POM-T) and [PW 12 O 40 ] 3 (POM-P), with silk fibroin (SF) to create 2D SF–POM layers on highly ordered pyrolytic graphite (HOPG) as resistive switching layers for memristors. We propose that the ordered SF layer template 0D POMs facilitate the formation of conductive filaments, thereby enhancing the variability of the manufactured memristors. AFM analysis revealed that both SF and SF–POM layers shared similar morphologies, while SF–POM–T formed larger aggregates, likely due to the stronger acidity of POM-T, which probably caused SF to aggregate and alter its secondary structure. Scanning Kelvin probe microscopy (SKPM) revealed that POMs reduced the contact potential difference of HOPG, resulting in lower work functions. Compared to an SF device, the SF–POM–P device showed improved memristive behavior, with a larger current gap and good repeatability over multiple sweeps; whereas the SF–POM–T device did not exhibit memristor activity, likely due to acidity-induced disruption of the SF template’s order and CF formation. More importantly, SF–POM–P devices also demonstrated programmable memristive states. Finally, combining simulation-driven memristor modeling, we showcase a co-design workflow for advancing bioinspired memristors through new materials design, synthesis, and device modeling and development.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗
NASA NTRS2014

Rewriting the Landform History of One of Africa's Three Largest Basins

The Kalahari Basin in southern Africa - one of the largest basins in Africa, along with the Congo and Chad basins - has attracted attention since David Livingstone traveled through the area in the 1840s. It is a semiarid desert with a large freshwater swampland known as the Okavango Swamp (150 km radius). This prominent megafan (a fan with radii >100 km), with its fingers of dark green forests projecting into the dun colors of the dunes of the Kalahari semi-desert, has been well photographed by astronauts over the years. The study area in the northern Kalahari basin is centered on the Okavango megafan of northwest Botswana, whose swampland has become well known as an African wildlife preserve of importance to biology and tourism alike. The Okavango River is unusual because it has deposited not one but two megafans along its course: the Okavango megafan and the Cubango megafan. The Okavango megafan is one of only three well-known megafans in Africa. Megafans on Earth were once thought to be rare, but recent research has documented 68 in Africa alone. Eleven megafans, plus three more candidates, have been documented in the area immediately surrounding the Okavango feature. These 11 megafans occupy the flattest and smoothest terrains adjacent to the neighboring upland and stand out as the darkest areas in the roughness map of the area. Megafan terrains occupy at least 200,000 sq km of the study area. The roughness map shown is based on an algorithm used first on Mars to quantify topographic roughness. Research of Earth's flattest terrains is just beginning with the aid of such maps, and it appears that these terrains are analogous to the flattest regions of Mars. Implications: 1. The variability in depositional style in each subbasin may apply Africa-wide: rift megafan length is dominated by rift width, whereas Owambo subbasin megafans are probably controlled by upland basin size; Zambezi subbasin megafans appear more like foreland basin types, with the position of the trunk river controlling size. 2. These perspectives were successfully applied to identify the largest megafan in the group (Cubango), a fan that was sufficiently overprinted by dunes and dry lakelets not to be detectable remotely. Such undertsanding can probably be applied on Mars, where Earth experience suggests megafans ought to exist. 3. Sweep angles of rivers on megafans drastically change the hydrology in some subbasins: when the Cubango and Kunene rivers were oriented to the Etosha Pan, it was probably a permanent water body. Now that the rivers are oriented away from the basin, 93 percent of the discharge area from the pan's northerly (main) source area is gone. 4. Biotic contact between major river systems was probably controlled by megafans situated on divides: various fish species that originated in the Congo basin are now found in the Upper Zambezi R., and vice versa, apparently because of river switching behavior on the Cassai megafan that has mediated migrations both to the south and the north.

Wilkinson, Justin↗
NASA NTRS1980

Top inlet system feasibility for transonic-supersonic fighter aircraft applications

Top inlet flow field and inlet performance data are presented which provide preliminary insight into the feasibility of upper-fuselage mounted inlet systems for transonic-supersonic fighter aircraft. Presented data span the Mach 0.2 to 2.0 envelope and enable evaluation of the influence of key aircraft configuration variables - inlet location, wing position, wing leading-edge extension (LEX) planform area, and variable incidence canards - on top inlet performance. The viability of this concept relative to more conventional inlet/airframe integrations is assessed via comparative evaluation of top and conventional inlet flow field parameters at transonic and supersonic speeds. It is shown that the action of the wing LEX vortex system produces a significant improvement in top inlet performance. Currently available transonic-supersonic data indicate that top inlet systems pose a viable configuration option for fighter aircraft requiring moderate angle of attack capability. However, recently acquired data indicate that increased angle of attack capability may be obtained by increasing wing leading-edge sweep angle.

Williams, T. L.↗