Search NASA⌕ Search

SEARCH · Search NASA

Results for “Volume fractions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Heat transfer in directly-irradiated high-temperature solid–gas flows laden with polydisperse particles

Heat transfer in directly-irradiated high-temperature solid–gas flows laden with polydisperse particles is investigated using a novel transient three-dimensional computational fluid dynamics model. The model couples particle–gas hydrodynamics of solid–gas flows laden with polydisperse particles, radiative heat transfer in non-grey absorbing, emitting and anisotropically-scattering multi-component participating media, conduction heat transfer in the gas phase, and interfacial convection heat transfer. The multiphase particle-in-cell method is used to predict high-fidelity solid–gas flow characteristics, such as the local discrete particle size distribution, with increased computational efficiency by combining the advantages of both Eulerian and Lagrangian methods. The multi-component radiative transfer model is implemented using an advanced collision-based Monte Carlo ray-tracing method. The number of the prescribed discrete particle components is found to be the key parameter affecting the computational accuracy and efficiency, which primarily depends on the size distribution of the particles. For the model particle–gas flow featuring free-falling Gamma-distributed ceramic particles exposed to concentrated solar irradiation, the particle volume fraction, radiative, fluid flow and thermal characteristics appear to converge with the increasing number of the discrete particle components. Five particle components are sufficient to obtain physically meaningful results. A further increase in the number of the particle components only slightly increases the accuracy of the numerical predictions at the expense of a rapidly increasing computational time. For five particle components, the particle vertical velocity at the receiver exit for particles with the diameter of 43.4 μm is 57% of that for the particles with the diameter of 202.8 μm. The temperatures of these two particle components increase from the initial ambient values by factors of 2 and 1.2, respectively, during the simulation time. In conclusion, the model developed allows for increased fidelity of particle–gas flow simulations with significant radiative effects.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Co-processing catalytic fast pyrolysis oil in an FCC reactor

Here, studies of co-processing catalytic fast pyrolysis (CFP) oil with vacuum gas oil (VGO) are conducted in a Davison Circulating Riser (DCR). The CFP oil (CFPO) for this study was produced by upgrading fast-pyrolysis vapors from pine in an ex-situ fixed-bed reactor. CFPOs were co-processed at up to a volume fraction of 0.05 with VGO at 521 degrees C and 257 kPa. The yields of oil, aqueous phase, tail gas, and coke were measured. The amount of coke was determined from the carbon containing components in the regenerator flue gas. A compositional analysis was conducted with gas chromatography and elemental analyzers. The organic liquids were distilled into gasoline, jet-fuel, diesel, and resid fractions. A biocarbon analysis was conducted on the organic phase and its individual boiling-point fractions. The results show a small decrease in liquid yield and a generally increased gas yield when co-processing CFPO with VGO. The experiments showed that 75%-100% of biocarbon is incorporated into liquid fuels relative to fossil carbon, depending on catalyst and CFPO. The measurements indicate that cracked CFPO components are predominantly included in the jet-fuel and diesel fractions. A techno-economic analysis (TEA) estimated the minimum fuel selling price (MSFP) for fuel-range products derived from FCC co-processing of CFPO at 24 to 29 $\$$/GJ ($\$$2.90 to $\$$3.50 per gasoline-gallon equivalent; GGE) at a yield of 4.87-7.14 GJ/t(biomass) or 40-58 GGE/t.

09 BIOMASS FUELS↗
DOE OSTI2022

A consistent and conservative Phase-Field method for multiphase incompressible flows

In the present study, a consistent and conservative Phase-Field method, including both the model and scheme, is developed for multiphase flows with an arbitrary number of immiscible and incompressible fluid phases. The consistency of mass conservation and the consistency of mass and momentum transport are implemented to address the issue of physically coupling the Phase-Field equation, which locates different phases, to the hydrodynamics. These two consistency conditions, as illustrated, provide the “optimal” coupling because (i) the new momentum equation resulting from them is Galilean invariant and implies the kinetic energy conservation, regardless of the details of the Phase-Field equation, and (ii) failures of satisfying the second law of thermodynamics or the consistency of reduction of the multiphase flow model only result from the same failures of the Phase-Field equation but are not due to the new momentum equation. Physical interpretation of the consistency conditions and their formulations are first provided, and general formulations that are obtained from the consistency conditions and independent of the interpretation of the velocity are summarized. Then, the present consistent and conservative multiphase flow model is completed by selecting a reduction consistent Phase-Field equation. Several novel techniques are developed to inherit the physical properties of the multiphase flows after discretization, including the gradient-based phase selection procedure, the momentum conservative method for the surface force, and the general theorems to preserve the consistency conditions on the discrete level. Equipped with those novel techniques, a consistent and conservative scheme for the present multiphase flow model is developed and analyzed. The scheme satisfies the consistency conditions, conserves the mass and momentum, and assures the summation of the volume fractions to be unity, on the fully discrete level and for an arbitrary number of phases. All those properties are numerically validated. Finally, numerical applications demonstrate that the present model and scheme are robust and effective in studying complicated multiphase dynamics, especially for those with large-density ratios.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Design and additive manufacturing of optimized electrodes for energy storage applications

Supercapacitors exhibit fast charging/discharging ability and have attracted considerable attention within the automotive, aerospace, and telecommunication industries. Porous carbons, prized for their high electrical conductivity and high surface area, have been attractive candidates for supercapacitor electrodes. Moving to thick electrodes is one strategy to further increase energy density due to a higher volume fraction of active material. However, thick electrodes suffer from sluggish charged species transport, which is why thin electrodes are currently favored. In this work, we investigate the use of computational optimization and additive manufacturing to design and fabricate thick porous electrodes with improved performance. Electrode performance was maximized by designing their morphologies via topology optimization and printing by projection micro stereolithography (PμSL) using commercial resin (PR48). The PR48 resin was then pyrolyzed (PR48-P) to create the final conductive electrode. The optimized PR48-P electrodes exhibited 99% improvement in capacitance compared to control electrodes printed with cubic lattice morphologies. To further improve performance, we formulated a resin combining graphene oxide (GO) and trimethylolpropane triacrylate (TMPTA). Electrodes printed with 3 wt% GO in TMPTA exhibited improved capacitance retention after pyrolysis compared to the PR48-P electrodes. Finally, this work demonstrates the benefits of using topology optimization to design electrodes and material development to improve functional properties of 3D printable electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Engineered Cementitious Composites (ECC) with limestone calcined clay cement (LC 3 )

Recent research have recognized that coupled use of calcined clay, limestone and cement clinker in concrete is viable to reduce environmental footprints at manufacture and to enhance material durability. In this study, a novel application of the limestone calcined clay cement (LC 3 ) is demonstrated by substituting the Ordinary Portland Cement (OPC) in Engineered Cementitious Composites (ECC). The composite mechanical properties including σ-δ and σ-ε relationships and residual crack widths were evaluated to 28 days under uniaxial tension. Matrix chemistry was characterized using thermogravimetric analysis and X-ray diffraction, while the pore structure of matrices and composites was analyzed using mercury intrusion porosimetry. The LC 3 -based ECC showed more rapid early strength development but lower 28-day strength (~32 MPa) due to a 20% higher water-to-solid ratio for attaining adequate workability and fiber dispersion. Nevertheless, the tensile strain capacity of LC 3 -based ECC achieved over 6% with an average residual crack width less than 50 μm. Additionally, the composite pore structure exhibited a decreasing volume fraction of large pores and voids (>100 nm) after substituting LC 3 for OPC. Here, the use of LC 3 marginally decreased the embodied material energy and cost, but led to about 32% and 28% reductions in CO 2 emissions compared to traditional OPC-based ECC and concrete, respectively. As a preliminary study, LC 3 -based ECC shows promise as a greener ductile concrete compared with OPC-based ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Lattice Boltzmann simulation of the dissolution of slag in alkaline solution using real-shape particles

Highlights: • A dissolution numerical model was proposed to capture the real dissolution kinetics of slag in alkaline solution. • The log forward dissolution rate of Si was described as a function of NBO/T and solution pH. • A threshold solid volume fraction of 0.688 was found for a voxel in 3D, 63.8% larger than that for a pixel in 2D. • The proposed dissolution numerical model provides a reliable alternative to study the dissolution kinetics of slag. A dissolution numerical model was proposed in this study to capture the real dissolution kinetics of slag in alkaline solution. It consists of three modules, i.e. (i) simulation of the initial particle parking structure of slag in alkaline solution using real-shape particles of slag, (ii) simulation of the chemical reactions between slag and solution based on the transition state theory, and (iii) simulation of the physical transport of aqueous ions using the lattice Boltzmann method. This dissolution numerical model was verified using experimental results, showing reasonable accuracy. After verification, the dissolution numerical model was implemented to study the influences of temperature and particle shape using a proper recipe of slag in alkaline solution. This recipe was designed to avoid solid phase precipitation or gel formation via thermodynamic analysis. The simulation results showed faster dissolution kinetics of slag when using higher temperatures and more irregular particle shapes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

edxia: Microstructure characterisation from quantified SEM-EDS hypermaps

The characterisation of cement paste microstructure is an important step towards understanding durability mechanisms in cementitious materials. Scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS) is a widely used technique to analyse the microstructure at the micron-scale. However, it is challenging, notably because the characteristic size of many phases is found on a scale smaller than the EDS interaction volume. This work presents a new image analysis framework to identify phases and quantify the microstructure of cementitious materials from SEM-EDS hypermaps. By leveraging domain knowledge, representative points are attributed to phases and mixtures of phases based on ratio plots. Then, quantitative analysis of the microstructure can be carried out (chemical composition, particle size distributions, volume fractions, …). We demonstrate the abilities of the framework, and we present possible applications and extensions of the method. The framework is available as both a graphical interface and a Python code.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of mixing on the generation of nanoparticles in cement systems

In this work, we study the effect of mixing intensity on the size and concentration of nanoparticles in quartz and cement systems. We vary the local shear rate in the studied suspensions induced by mixing by either changing solid volume fraction or mixing speed. Our results obtained on quartz, cement and quartz-cement suspensions provide a master curve relating the concentration of nanoparticles in the pore solution as a function of the local shearing conditions computed at a micromechanical level. Our results suggest, in accordance with literature, that high mixing intensity is at the origin of a detachment of nano-hydrates from the surface of cement particles. These nanoparticles can be stabilized and therefore detected in the pore-solution only in the presence of superplasticizers, which inhibit their agglomeration to other particles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Relating phase transitions to pore size distributions and mechanical mortar properties in CSA-OPC-C$ based systems – The potential impact of delayed straetlingite formation

The scope of this research is to investigate the performance evolution of five ternary CSA-OPC-Cs systems. Time resolved thermodynamic modeling was employed to gain insight into changes in the volume fractions of the hydrating pastes and link these changes to trends in the pore size distributions of the mortars. Pore solution analyses were performed to investigate which hydrates have the potential to exert high crystallization pressures. In three out of five blends the resulting tensile stress exceeded the tensile strength of the materials, resulting in the occurrence of coarse pores, which could be linked to the measured compressive strengths. Two damaging crystallization processes were identified in the investigated blends. One is the continuous precipitation of ettringite at high supersaturation in a system with high anhydrite addition. The other is the delayed crystallization of straetlingite at high supersaturation and crystallization pressure in the confined environment of mature pastes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reconstruction of concrete microstructure using complementarity of X-ray and neutron tomography

The concrete microstructure was successfully reconstructed using the complementarity of X-ray and neutron computed tomography (CT). Neither tomogram alone was found to be suitable to properly describe the microstructure of concrete under this study. However, by merging the information revealed by the two modalities, and using image segmentation, noise reduction, and image registration techniques we reconstruct the concrete microstructure. Void, aggregate, and cement paste phases are successfully captured down to the images' spatial resolution, even though the aggregate consists of multiple minerals. The coarse-aggregate volume fraction of the reconstructed microstructure was similar to that of the mixing proportions. Furthermore, image-based finite element analysis is performed to demonstrate the effects of microstructure on stress concentration and strain localization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Estimation of constituent properties of concrete materials with an artificial neural network based method

Multi-scale models are developed for heterogeneous concrete materials to estimate their macroscopic mechanical properties in terms of micro-structural data. One crucial challenge of those models is the identification of local properties of constituent phases. In this paper, we present an efficient method based on Artificial Neural Networks (ANN). Typical concrete materials are taken as example. A macroscopic analytical strength criterion is established from three steps of nonlinear homogenization procedure. The macroscopic strength of materials is determined as a function of the frictional coefficient and cohesion of solid cement particles at nanometer scale, intra-particle pores, inter-particle pores and aggregates (inclusions). The objective is to identify the nanoscopic frictional coefficient and cohesion of cement particle from measured macroscopic values of uniaxial compression and tensile strengths. For this purpose, a numerical method based on the ANN is developed. With the analytical macroscopic strength criterion, sensitivity studies are first realized to identify the most important micro-structural parameters influencing the macroscopic strength of concrete. A simplified analytical macroscopic strength criterion is then proposed. A large dataset is further constructed through the inversion of the analytical strength criterion by using the aggregates volume fraction, porosity, macroscopic uniaxial tensile and compressive strengths as input variables and the frictional coefficient and cohesion of cement particles as output unknowns. An ANN model containing four hidden layers and 100 neurons in each layer is constructed and trained by using this dataset. Various types of validation of the ANN model are performed. It is found that the proposed ANN based model can effectively predict the frictional coefficient and cohesion of porous cement paste at the microscopic scale with a very good accuracy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of a silicon carbide ceramic based counter-flow heat exchanger by binder jetting and liquid silicon infiltration for concentrating solar power

A silicon carbide ceramic counter-flow heat exchanger with integrated headers was printed by binder jetting additive manufacturing process. Multiple phenolic binder infiltration cycles (3 or 5) followed by pyrolysis were conducted to increase the net carbon content of the printed SiC specimens. Subsequently, to attain full densification, silicon melt infiltration was used. The microstructure and mechanical properties were comprehensively characterized on the densified material. The chemical compositions and visual distribution of the various regions in the specimens were determined via scanning electron microscopy, while X-ray diffraction and synchrotron µ-computed tomography were used to provide a quantitative assessment of the volume fractions of the identified phase regions. Microhardness measurements showed dependence on the local microstructure. The fracture strength of the material was correlated with the specimen density and agreed with the reported values in the literature. High-temperature exposure at 750 °C for up to 200h did not degrade the strength for the specimens with three phenolic-binder infiltrations; however, the strengths degraded for ones with five phenolic-binder infiltrations. The associated fracture toughnesses of the specimens were ~3.4 MPam 1/2 at room temperature and 750°C, and the thermal conductivities varied from >150 W/mK at room temperature to ~45 W/mK at 750°C. Hence, this study validated the use of the binder-jetting printed SiC ceramic materials for high-temperature heat exchanges. Lastly, we also present in this work the first successful fabrication of a binder-jetting printed one-piece dense SiC ceramic heat exchanger body with unblocked channels that can be used for the flow of heat transfer fluids.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deep learning for drag force modelling in dilute, poly-dispersed particle-laden flows with irregular-shaped particles

Here, this study applies machine learning-based approaches to develop a drag force model for irregular-shaped particles in incompressible flows. The particle-laden flows are studied through an in-house particle-resolved direct numerical simulation (PR-DNS) at low-intermediate Reynolds numbers (Re). We utilize the PR-DNS to obtain drag force coefficients and flow fields of single particles. A variational auto-encoder model is used to obtain latent vectors to represent the geometrical features of the particles, and artificial neural networks (ANN) are developed to predict drag force coefficients and flow fields of the single particles. This study applies a pairwise interaction extended point-particle (PIEP) model to obtain the coefficients assuming the flow fields of neighboring particles can be linearly superposed. The PIEP method shows significant improvement on prediction for a few neighbored particles. In addition, the results reveal R2 scores of 0.56-0.62 and errors of 9.1-10.0 % for the dilute, polydispersed systems with a volume fraction of 0.5 %.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

$\mathrm{IH}$-$\mathrm{GAN}$: A conditional generative model for implicit surface-based inverse design of cellular structures

Variable-density cellular structures can overcome connectivity and manufacturability issues of topologically optimized structures, particularly those represented as discrete density maps. However, the optimization of such cellular structures is challenging due to the multiscale design problem. Past work addressing this problem generally either only optimizes the volume fraction of single-type unit cells but ignoring the effects of unit cell geometry on properties, or considers the geometry–property relation but builds this relation via heuristics. In contrast, we propose a simple yet more principled way to accurately model the property to geometry mapping using a conditional deep generative model, named Inverse Homogenization Generative Adversarial Network (IH-GAN). It learns the conditional distribution of unit cell geometries given properties and can realize the one-to-many mapping from properties to geometries. Here we further reduce the complexity of IH-GAN by using the implicit function parameterization to represent unit cell geometries. Results show that our method can 1) generate various unit cells that satisfy given material properties with high accuracy (R 2 -scores between target properties and properties of generated unit cells >98%) and 2) improve the optimized structural performance over the conventional variable-density single-type structure. In the minimum compliance example, our IH-GAN generated structure achieves a 79.7% reduction in concentrated stress and an extra 3.03% reduction in displacement. In the target deformation examples, our IH-GAN generated structure reduces the target matching error by 86.4% and 79.6% for two test cases, respectively. We also demonstrated that the connectivity issue for multi-type unit cells can be solved by transition layer blending.

42 ENGINEERING↗
DOE OSTI2023

Kinetic model-based group contribution method for derived cetane number prediction of oxygenated fuel components and blends

A four-step autoignition model was used to derive an expression for the ignition delay (ID) measured in ignition quality testers (IQT) with the derived cetane number (DCN) determined from this ID using the ASTM D6890 standard correlation. The model predicts DCN for individual compounds and blends as a function of each compound's global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in each compound. Measurement data for 125 compounds and 94 binary and ternary blends (including oxygenates: alcohols, aldehydes, esters, ethers, and ketones), from literature and from measurements performed in our lab, were used to obtain the dependence of the measured ignition delay on each functional group. The new kinetic model-based group contribution method was able to predict the ignition delay of both pure compounds and blends, with an average DCN error of 4.4 (19%) and 2.8 (11%), respectively. Here, the blend model was also used to develop an ID mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule gave an average DCN error of 3.6 (16%) for blends. Both the blend model and mixing rule were found to be superior compared to standard linear by volume fraction or mole fraction mixing rules commonly used to estimate the DCN of mixtures.

42 ENGINEERING↗
DOE OSTI2021

A microstructure-based modeling approach to predict the mechanical properties of Zr alloy with hydride precipitates

In nuclear reactors, hydrides can form in fuel cladding due to hydrogen absorption in ZIrcaloy and cause embrittlement. This work presents a microstructure-based finite element model to predict the stress-strain response of Zircaloy containing hydrides. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. The constitutive material model for zircaloy in this study is based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as brittle material along with a damage model. Hydride formation inside the zircoloy matrix results in residual stress. This phenomenon is also captured in this model. A parametric study has been conducted to understand the effect of volume fraction, orientation, and lamellae thickness of the hydride phase on the mechanical properties of the overall material.

Kulkarni, Shank S.↗
DOE OSTI2021

Modeling discontinuous dynamic recrystallization containing second phase particles in magnesium alloys utilizing phase field method

Pre-existing second phase particles can induce particle stimulated nucleation (PSN) and pinning effect on grain boundaries during DRX process of magnesium alloys. The interaction among pinning effect, PSN mechanism and strain-induced grain boundary migration (SIBM) nucleation mechanism imposes challenge in quantitative study of microstructure evolution. A phase field model that describes discontinuous dynamic recrystallization process considering second phase particles (PF-DDRX-SP) which mainly distribute along grain boundaries is developed. The second phase order parameter with diffusion interface is introduced to the free energy function. With considering the pinning effect of second phase particles on grain boundaries, the grain boundary energy couples the interaction between second phase and grains. The effect of second phase on dislocation density evolution is considered in the model, and the PSN and SIBM mechanism are both executed by limiting the nucleation position to the grain boundary and the second phase interface. For the validation, the initial topology consistent with initial microstructure is applied to the simulation of DRX kinetics and flow behavior of AZ80 magnesium alloy, and great reliability and accuracy of developed model is indicated. Furthermore, through the model, the microstructure evolution with different particle size and with different volume fraction of round particle during DRX process were simulated. Finally, the results show that particles with higher dispersion reduce the number of DRX nuclei, which indicate that second phase particles suppress the nucleation at grain boundaries because of the pinning effect. More importantly, the proposed model could also quantitatively predict the relationships between the parameters of second phase particles and DRX behaviors, and enable to optimize the initial second phase structure in a uniform grain structure during thermomechanical process.

36 MATERIALS SCIENCE↗