Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING MACHINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Evaluation of residual stresses in isothermal friction stir welded 304L stainless steel plates

Friction stir welding was performed on 304L SS plates in order to heal simulated cracks created by electrical discharge machining. Two different tool temperatures (825 and 725 °C) were chosen for this study. Both neutron diffraction and X-ray diffraction techniques were employed to evaluate the residual stresses along two orthogonal reference directions, longitudinal (syy) and transverse (sxx). The former technique was also used to measure residual stresses at various depths. It was found that, at 1 mm depth from the top surface inside the stir zone (SZ), the longitudinal component was tensile in nature while the transverse component was compressive. The nature and magnitude of the residual stress fields, and the position of the peak residual stresses were found to vary with the weld depth. The SZ of the 725 °C weld exhibited higher peak stress than 825 °C weld mainly due to a lack of stress relief at the lower temperature.

Friction stir welding, Steel↗

Effect of Weld Tool Geometry on Friction Stir Welded Ti-6Al-4V

In this study, flat 0.250" thick Ti-6Al-4V panels were friction stir welded (FSWed) using weld tools with tapered pins. The five different pin geometries of the weld tools included: 0 degree (straight cylinder), 15 degree, 30 degree, 45 degree, and 60 degree angles on the frustum. All weld tools had a smooth 7 degree concave shoulder and were made from microwave sintered tungsten carbide. For each weld tool geometry, the FSW process parameters were optimized to eliminate internal defects. All the welds were produced in position control with a 2.5 degree lead angle using a butt joint configuration for the panels. The process parameters of spindle rpm and travel speed were varied, altering the hot working conditions imparted to the workpiece. Load cells on the FSWing machine allowed for the torque, the plunge force, and the plow force to be recorded during welding. Resulting mechanical properties were evaluated from tensile tests results of the FSWjoints. Variations in the material flow were investigated by use of microstructural analysis including optical microscopy (OM), scanning electron microscopy (SEM), and orientation image mapping (aIM).

Querin, Joseph A.↗

Water-Resistant Container Testing: A426-1000 Container Design

The purpose of this report is to detail the results of water ingress testing conducted on the A426-1000 container design and discuss these results against the water-resistant container requirements of TA55-AP- 522 and PA-RD-01009. The A426-1000 is a proposed commercially off the shelf inner container option for material storage inside of a glovebox and/or as an approved non-hermetically sealed inner of an approved packaging configuration inside of an approved outer container as listed in PA-RD-01022. The A426-1000 is shaped like a slip lid container, made of 316L stainless steel, and utilizes a smooth, threaded lid with a silicone O-ring for closure and containment. This container both lid and body is machined out of one billet piece of 316L stainless steel with no welds. See Figure 1 and Table 1 for a summary of the container specifications. For more details on the container design, see Section 1.4.

42 ENGINEERING↗

Fatigue behavior of two alloys for Space Shuttle applications

Two superalloys used extensively in the Space Shuttle main engine are Incoloy 903 and Inconel 718. The fatigue behavior of the two alloys under varying conditions is considered. Three heats of Incoloy 903 and two of Inconel 718 were used in the study. Material was tested in several conditions, including mill polish, longitudinal mill polish, transverse mill polish, chemically milled, chemically milled plus shotpeened on one side and on both sides, gas tungsten arc welded, and electron beam welded. Both round and flat tensile specimens were tested in universal test machines. It was found that surface condition influences test results. Transverse scratches resulting from polishing and rougher surfaces lower the stress at runout in relation to that obtained on longitudinally polished and/or smooth-surfaced specimens.

Adsit, N. R.↗

Resolution of Tolerance Variations

The connector/adapter assembly (CAA) is one component of a higher-level assembly. A simplified representation of the CAA is illustrated in Figure 1. The location of each CAA is required to meet a specific positional requirement. Several CAAs have been measured and found to be out of tolerance. The connector and the adapter are welded to each other such that the cylindrical axes of the two components are coaxial. The positional tolerance condition requires that all points on the outer surface of the CAA must be within a defined maximum diameter, as illustrated in Figure 1. Two different methods have been developed to measure the CAA positions from coordinate measuring machine (CMM) data. One method (RevD) extrapolates the data from two circles approximately midway from the weld region to each end. The second method (RevF) measures points that are much closer to the actual ends.

42 ENGINEERING↗

Harvesting Reactor Pressure Vessel Beltline Material from the Decommissioned Zion Nuclear Power Plant Unit 1

The decommissioning of the Zion Nuclear Power Plant (NPP) provided a unique opportunity to harvest and study service-aged reactor pressure vessel (RPV) beltline materials. This work, conducted through the U.S. Department of Energy’s Light Water Reactor Sustainability (LWRS) Program, aims to improve the understanding of radiation-induced embrittlement to support extended nuclear plant operations. Material segments containing the Linde 80 flux, wire heat 72105 (WF-70) beltline weld and the A533B Heat B7835-1 base metal, obtained from the intermediate shell region with a peak fluence of 0.7 × 10 19 n/cm 2 (E > 1.0 MeV), were extracted, cut into blocks, and machined into test specimens for mechanical and microstructural characterization. The segmentation process involved oxy-propane torch-cutting, followed by precision machining using wire saws and electrical discharge machining (EDM). A chemical composition analysis confirmed the expected variations in alloying elements, with copper levels being notably higher in the weld metal. The harvested specimens enable a detailed evaluation of through-wall embrittlement gradients, a comparison with the existing surveillance data, and the validation of predictive embrittlement models. This study provides critical data for assessing long-term reactor vessel integrity, informing aging-management strategies, and supporting regulatory decisions to extend the life of nuclear plants. This article is a revised and expanded version of a paper entitled, “Current Status of the Characterization of RPV Materials Harvested from the Decommissioned Zion Unit 1 Nuclear Power Plant”, PVP2017-65090, which was accepted and presented at the ASME 2017 Pressure Vessels and Piping Conference, Waikoloa, HI, USA, 16–20 July 2017.

harvesting beltline material↗

Stability of zirconium hydride

This reports complete Milestone M2.2.1 Stability of zirconium hydride: Experimental investigation of the hydrogen concentration of encapsulated zirconium hydride before and after joining. In this milestone, we first report the successful fabrication of crack-free bulk zirconium hydride by using the ORNL static hydriding system. The fabricated hydride was characterized by using X-ray diffraction (XRD) and X-ray computed tomography (XCT). XRD results showed that the δ-phase zirconium hydride, α-zirconium, and ε-phase hydride were present. XCT confirmed the absence of the internal cracking. The hydrogen concentration was determined by the weight change before and after hydrogen loading, given the fact that the oxide phase was not found during XRD analysis. Two metallic cladding materials, i.e., molybdenum and FeCrAl, were selected to encapsulate the fabricated zirconium hydride pellets. Demonstration capsules were designed and machined. Mo crucible was successfully sealed by using a combination of electron beam welding and gas tungsten arc welding. Due to the undesired neutronics property of Mo, further investigation of this cladding material was not pursued. Electron beam welding and laser beam welding were employed to seal the FeCrAl capsules. XRD were performed on the zirconium hydride before and after the sealing. The results showed that the welding process has negligible impact on the hydrogen content in the FeCrAl-canned zirconium hydride. The presented work fulfilled the proposed work under this milestone and paves a pathway to fabricate single-phase zirconium hydride and to develop robust cladding materials to can bulk zirconium hydride.

36 MATERIALS SCIENCE↗

Test fittings for dimensionally critical tubes

Method using lightweight fitting protects tubes and tube stubs during testing and through to final welding. Fitting does not interfere with final welding or brazing like temporary test fittings, and is not heavy like machined-on integral fittings with face-seal 0-rings. Fitting approach is adaptable to many types of components, including valves, transducers, and filters.

Hagler, R.↗

Graphite composite truss welding and cap section forming subsystems. Volume 1: Executive summary

A rolltrusion process was developed for forming of a hybrid, single-ply woven graphite and glass fiber cloth, impregnated with a polysulfone resin and coated with TI02 pigmented P-1700 resin into strips for the on-orbit fabrication of triangular truss segments. Ultrasonic welding in vacuum showed no identifiable effects on weld strength or resin flow characteristics. An existing bench model cap roll forming machine was modified and used to roll form caps for the prototype test truss and for column test specimens in order to test local buckling and torsional instability characteristics.

Source record↗

Practical Challenges and Failure Modes During Fabrication of Haynes 230 Micro-Pin Solar Receivers for High Temperature Supercritical Carbon Dioxide Operation

Printed circuit heat exchangers (PCHX) fabricated from high nickel alloys have shown promise as primary heat exchangers, recuperators, and solar receivers for high temperature and pressure supercritical carbon dioxide power cycles. There are numerous challenges in fabricating these devices including forming channel features, joining via diffusion or transient liquid phase bonding, and brazing/welding of headers. Commercial entities are understandably hesitant to share propriety best practices, and both commercial and non-commercial entities working on these components tend not to publically share failures and mistakes. However, sharing of this information could prevent similar costly errors and further the understanding of the coupled manufacturing, materials and mechanics issues in creating these components. Thus, in this paper, we document the challenges, failures, and mitigation methods uncovered in fabrication of prototype micro-pin based solar thermal receivers constructed of Haynes 230 and fabricated through a combination of photochemical machining (PCM), wire electrical discharge machining (EDM), transient liquid phase (TLP) bonding, vacuum brazing, and gas tungsten arc welding (GTAW). The receiver is designed to absorb concentrated solar fluxes greater than 140 W cm-2, while heating supercritical carbon dioxide from 550 °C to 720 °C at a pressure of 20 MPa to 25 MPa. The prototype receiver consists of a thin (~ 450 µm), Haynes 230 coversheet bonded to a 15 cm × 15 cm Haynes 230 micro-pin plate. The pieces are joined using a TLP bonding process with a nickel-phosphorus interlayer. Prior to bonding, micro-pins with height ~150 µm and diameter 300 µm are fabricated using PCM in the plate, and through slot features are made using wire EDM. Finally, flow headers are joined to the microchannel plate through a combination of vacuum brazing and GTAW. During hydrostatic proof testing, the prototype device failed when the coversheet delaminated from the pin array at a pressure of 290 bar. A failure analysis including scanning electron microscopy (SEM) to view failure sites and energy-dispersive X-ray spectroscopy (EDS) to evaluate elemental analysis of the failed areas was conducted. The failure modes can be broadly categorized as (1) failures potentially relating to reliquification of the transient liquid phase bonds between the micro-pins plate and coversheet during post-processing, (2) failures related to manufacturing defects, and (3) failures attributed to design.

14 SOLAR ENERGY↗

Physics-informed machine learning assisted uncertainty quantification for the corrosion of dissimilar material joints

Jointing techniques like the Self-Piercing Riveting (SPR), Resistance Spot Welding (RSW) and Rivet-Weld (RW) joints are used for mass production of dissimilar material joints due to their high performance, short cycle time, and adaptability. However, the service life and safety usage of these joints can be largely impacted by the galvanic corrosion due to the difference in equilibrium potentials between the metals with the presence of electrolyte. Here, in this paper, we focus on Al-Fe galvanic corrosion and develop physics-informed machine learning based surrogate model for statistical corrosion analysis, which enables the reliability analysis of dissimilar material joints under corrosion environment. In this study, a physics-based finite element (FE) corrosion model has been developed to simulate the galvanic corrosion between a Fe cathode and an Al anode. Geometric and environmental factors including crevice gap, roughness of anode, conductivity, and the temperature of the electrolyte are investigated. Further, a thorough Uncertainty Quantification (UQ) analysis is conducted for the overall corrosion behavior of the Fe-Al joints. It is found that the electrolyte conductivity has the largest effects on the material loss and needs to be managed closely for better corrosion control. This will help in designing and manufacturing joints with improved corrosion performance.

42 ENGINEERING↗

Introduction to the design rules for Metal Big Area Additive Manufacturing

Wire feed metal additive manufacturing offers advantages, such as large build volumes and high build rates, over powder bed and blown powder techniques, but it has its own disadvantages, i.e., lower feature resolution and bead morphology control issues. A new wire feed metal additive manufacturing process called Metal Big Area Additive Manufacturing (mBAAM) uses a Gas Metal Arc Weld system on an articulated robot arm to increase build volume and deposition rate in comparison to powder bed techniques. The high deposition rate implies a low-resolution process; therefore, parts designed for mBAAM must incorporate the use of machining to achieve certain features. Here, this paper presents an introduction to how design rules, such as overhang constraint, large weld bead thickness, and support structure, for mBAAM interact in the context of an excavator arm case study, which was designed using topology optimization.

42 ENGINEERING↗

An Eddy Current Case Study using NASA’s Transfer Function and Limited-Sample Probability of Detection Guidebooks

Probability of detection (POD) requirements for NASA fracture-critical human-rated systems can be met by (1) claiming ‘similarity’ to NASA Standard Nondestructive Evaluation (NDE) flaw sizes or (2) by inspector-specific POD demonstration, known as NASA Special NDE. Standard NDE flaw sizes are intended to represent the detection capability of most qualified inspectors, and were primarily based on POD studies in the development of the Space Shuttle Program Orbiter fracture control plan. However, these Standard NDE flaw sizes were based on fatigue cracks in flat panels of one material alloy over a limited range of panel thicknesses. While the POD study was comprehensive, the inspection conditions are relatively narrow. An evaluation of similarity between the Standard NDE POD study and flight component conditions is required to apply Standard NDE to specific flight component inspections. A similarity evaluation may include differences in materials, surface finish, component geometry (e.g., curvature, corners, welds), and inspection access. Similarity is typically based on a qualitative engineering evaluation. Recently, NASA published a quantitative methodology to assess similarity. If similarity is not supported by test and analysis, then the methodology provides a transfer function of flaw size for Special NDE POD demonstration. NASA recommends that Special POD demonstrations use flaws that are flight-like or more difficult to detect than flight component flaws, which are commonly induced fatigue cracks. Often, it is not feasible to induce fatigue cracks in flight component geometry, and therefore, a simpler representative geometry is used, commonly a flat panel, for POD demonstration. Inducing cracks in simple geometry specimens can be time-consuming and expensive, and thus, minimizing the number of flawed specimens is desired. Traditionally, NASA Special NDE demonstration was limited to MIL-HDBK-1823A methods or the binomial point-estimate method (PEM), commonly known as 29/29. Recently, NASA published a limited-sample POD (LS-POD) methodology for signal-response NDE techniques (e.g., eddy current) that provides POD demonstration with fewer specimens than previous approaches. LS-POD suggests a minimum of 10 flawed specimens, compared to 29 in the PEM and the suggested minimum of 40 from MIL-HDBK-1823A. The methodology also includes new guidance on evaluating the probability of false calls. In this presentation, these new transfer function and LS-POD methodologies are described and illustrated through an eddy current detection capability of far-side flaws on thin welded panels. A geometry-based transfer function is developed using electro-discharge machined (EDM) notches in flight component and simple geometry to estimate the Special NDE flaw size that is representative of the critical initial flaw size required by the fracture analysis. Then, fatigue cracks are induced in simple flat panels of the transferred flaw size, and the LS-POD methodology is used for Special NDE demonstration.

P. A. Parker↗

A summary of tests on Invar welded with 308L and 8N12 welding rods

The cost and difficulty in obtaining Invarod, the recommended welding rod to weld Invar, nessitated the investigation of substituting more readily available rods that would meet the cryogenic design criteria for the National Transonic Facility (NTF). Two weld rods, 308L and 8N12, were chosen as promising candidates. Four welded specimen plates were made; two plates for each type of weld rod. One plate from each of the 308L and 8N12 weldings was thermally cycled 50 times between 366 K and 89 K while the two remaining plates were not thermally cycled. Specimens were machined from all four plates for three types of tests: tensile, charpy impact, and guided-bend. The methods in making the specimen plates, conduction of the tests, test results, and conclusions leading to the selection of a weld rod are presented.

Cox, J. W.↗

Weldability of Weldalite (tm) 049 with and without TiB2 reinforcement

The effects are assessed of TiB2 reinforcement and parent alloy Li content on the weldability of Weldalite (tm) 049 type alloys. Welding trials were performed using either AC or DC polarity gas tungsten arc (GTA) welding according to described procedures. The welding was performed under conditions of high restraint on 5 cm (2 in) wide x 25.4 cm (10 in) long plates machined from the 0.952 cm (0.375 in) extruded bar parallel to the extrusion direction. A 37.5 deg bevel was machined on the center edge of the extruded bar. Cut rod filler wire was machined from three alloys, and one commercially available 2319 filler wire was also used. The preliminary assessment of the weldability revealed no propensity for hot cracking under conditions of high restraint. This result is significant, because hot cracking has been reported for all other leading aluminum lithium alloys welded with certain conventional filler alloys. The strengths for Weldalite parent welded with parent filler obtained were higher than those for alloys used in launch systems, such as 2219 and 2014 welded with 2319 and 4043 fillers, respectively. Even higher values were obtained by variable polarity plasma arc welding (e.g., 54 ksi (372 MPa) mean tensile strength).

Source record↗

Fe-24 wt.%Cr-4.1 wt.%C hardfacing alloy: Microstructure and carbide refinement mechanisms with ceria additive

The microstructure and carbide refinement mechanisms of Fe-24 wt.%Cr-4.1 wt.%C hardfacing alloys with 0 wt.%, 0.5 wt.%, 1.0 wt.%, 2 wt.%, and 4 wt.% ceria additives have been systematically investigated in this work. Optical microscopy, field emission scanning electron microscopy with energy dispersive spectrometer, and X-ray diffraction were collectively used to study the microstructure, the phase components, and the chemical formation of inclusion formed in the welding process. Wear-resistance of the alloys was comparatively studied using an abrasive wear testing machine. The structure analysis results show that the Fe-Cr-C hardfacing alloy mainly consists of martensite, retained austenite, MC carbide and M{sub 7}C{sub 3} carbide. With increasing ceria additive contents, the average size of the primary M{sub 7}C{sub 3} carbide decreases and reaches a most refined state in the alloy with 2 wt.% ceria additives. Comparative wear tests data shows that the wear resistance of the hardfacing alloys with ceria additives is better than that without ceria additive. In a good agreement with the carbide refinement results, the wear resistance of the alloy reaches an optimum level in the sample with 2 wt.% ceria additive. The main RE inclusion type identified with in-situ XRD analysis is RE inclusion Ce{sub 2}O{sub 2}S. Thermodynamics calculation confirms that this type of RE inclusion could precipitate prior to M{sub 7}C{sub 3} carbides, and act as a heterogeneous nucleus for M{sub 7}C{sub 3} in the welding process, which effectively provides a mechanism for significant refinement of the M{sub 7}C{sub 3} carbide and improves its wear resistance. - Graphical Abstract: Rare Earth inclusion (Ce{sub 2}O{sub 2}S) distributes in the primary M{sub 7}C{sub 3} carbide. Moreover, Ce{sub 2}O{sub 2}S, which acts as heterogeneous nuclei of the primary M{sub 7}C{sub 3} carbide, is medium effective. Therefore, the primary M{sub 7}C{sub 3} carbide has been refined. Highlights: Black-Right-Pointing-Pointer Micro-hardness of primary M{sub 7}C{sub 3} carbide in Fe-Cr-C hardfacing alloy is 1594 HV. Black-Right-Pointing-Pointer RE inclusion Ce{sub 2}O{sub 2}S can be observed in the primary M{sub 7}C{sub 3} carbide. Black-Right-Pointing-Pointer Ce{sub 2}O{sub 2}S as heterogeneous nuclei of the Cr{sub 7}C{sub 3} is medium effective. Black-Right-Pointing-Pointer Primary carbide is most refined with 2 wt.% ceria additive.

36 MATERIALS SCIENCE↗