Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Wind Tunnel Model Support Cart with Telescoping Mast and Cable Yaw Drive

The 14-by-22 Foot Subsonic Tunnel at NASA Langley Research Center uses model carts to support and position models in the test section. The carts are portable through the use of air bearings and can be moved from the test to the Model Prep Area (MPA) to change models in preparation for a new test. This paper describes the design of a new model cart that is three feet shorter than existing carts. This will eliminate clearance problems when moving the model and cart from the MPA to the test section.

Gregory, Peyton B.↗
NASA NTRS2012

Lessons in the Design and Characterization Testing of the Semi-Span Super-Sonic Transport (S4T) Wind-Tunnel Model

This paper focuses on some of the more challenging design processes and characterization tests of the Semi-Span Super-Sonic Transport (S4T)-Active Controls Testbed (ACT). The model was successfully tested in four entries in the National Aeronautics and Space Administration Langley Transonic Dynamics Tunnel to satisfy the goals and objectives of the Fundamental Aeronautics Program Supersonic Project Aero-Propulso-Servo-Elastic effort. Due to the complexity of the S4T-ACT, only a small sample of the technical challenges for designing and characterizing the model will be presented. Specifically, the challenges encountered in designing the model include scaling the Technology Concept Airplane to model scale, designing the model fuselage, aileron actuator, and engine pylons. Characterization tests included full model ground vibration tests, wing stiffness measurements, geometry measurements, proof load testing, and measurement of fuselage static and dynamic properties.

Source record↗
NASA NTRSDate not supplied

Scaled Aeroelastic Wind Tunnel Model Design with Topology Optimization

The goal of this work is to use numerical aeroelastic topology optimization to design flutter models to be tested in the Transonic Dynamics Tunnel, as part of an envisioned validation experiment for transonic flutter. The topological design develops the structural details of a variable-thickness aluminum plate located at the camber line of a scaled transport aircraft model, in order to satisfy the various conflicting design requirements, including a prescribed flutter boundary, flutter frequency, and static stress levels. Four designs are demonstrated here, where it is shown that the simultaneous design of a cylindrical tip store can help ease the conflict between low stiffness (to allow a wing to flutter in the tunnel envelope) and high strength (to ensure safe structural response). The tip store complicates the geometrical features of the wing, however, and is generally undesirable from the vantage point of a validation experiment.

Aeroelasticity↗
NASA NTRS1995

SOFIA 2 model telescope wind tunnel test report

This document outlines the tests performed to make aerodynamic force and torque measurements on the SOFIA wind tunnel model telescope. These tests were performed during the SOFIA 2 wind tunnel test in the 14 ft wind tunnel during the months of June through August 1994. The test was designed to measure the dynamic cross elevation moment acting on the SOFIA model telescope due to aerodynamic loading. The measurements were taken with the telescope mounted in an open cavity in the tail section of the SOFIA model 747. The purpose of the test was to obtain an estimate of the full scale aerodynamic disturbance spectrum, by scaling up the wind tunnel results (taking into account differences in sail area, air density, cavity dimension, etc.). An estimate of the full scale cross elevation moment spectrum was needed to help determine the impact this disturbance would have on the telescope positioning system requirements. A model of the telescope structure, made of a light weight composite material, was mounted in the open cavity of the SOFIA wind tunnel model. This model was mounted via a force balance to the cavity bulkhead. Despite efforts to use a 'stiff' balance, and a lightweight model, the balance/telescope system had a very low resonant frequency (37 Hz) compared to the desired measurement bandwidth (1000 Hz). Due to this mechanical resonance of the balance/telescope system, the balance alone could not provide an accurate measure of applied aerodynamic force at the high frequencies desired. A method of measurement was developed that incorporated accelerometers in addition to the balance signal, to calculate the aerodynamic force.

Keas, Paul↗
NASA NTRS1976

Simulation of the atmospheric boundary layer in the wind tunnel for modeling of wind loads on low-rise structures

The lower part of the atmospheric boundary layer (strong wind conditions) was simulated in low speed wind tunnel for the modeling of wind loads on low-rise structures. The turbulence characteristics of the turbulent boundary layer in the wind tunnel are compared with full scale measurements and with measurements made at NASA Wallops Flight Center. Wind pressures measured on roofs of a 1:70 scale model of a small single family dwelling were compared with results obtained from full scale measurements. The results indicate a favorable comparison between full scale and model pressure data as far as mean, r.m.s. and peak pressures are concerned. In addition, results also indicate that proper modeling of the turbulence is essential for proper simulation of the wind pressures.

Tieleman, H. W.↗
NASA NTRS1927

Method of Correcting Wind Tunnel Data for Omitted Parts of Airplane Models

Wind tunnel models do not have complete similarity to the full scale airplane. Part of the dissimilarity is due to the difference between the stationary model in the artificial wind stream of the tunnel and the moving airplane in still air. There are a number of other reasons for departing from exact geometrical similitude. For reasons of accuracy and economy, all minor parts of the full scale airplane, such as struts, wires, fittings, control horns and other parts whose scale corrections are large are removed from wind tunnel models. By omitting the minor parts of the airplane in the wind tunnel model and adding to the forces and moments of the model those omitted parts measured full scale and properly reduced, the scale effects of such parts disappear from the model data. Scale effects due to major parts of the airplane, particularly the fuselage and wings, can be corrected by omitting the propeller and making the surface of the model as smooth as possible, two further departures from geometrical similitude between model and full scale that add considerably to the accuracy and economy of model tests.

Smith, R H↗
NASA NTRS2002

Uncertainty of Videogrammetric Techniques used for Aerodynamic Testing

The uncertainty of videogrammetric techniques used for the measurement of static aeroelastic wind tunnel model deformation and wind tunnel model pitch angle is discussed. Sensitivity analyses and geometrical considerations of uncertainty are augmented by analyses of experimental data in which videogrammetric angle measurements were taken simultaneously with precision servo accelerometers corrected for dynamics. An analysis of variance (ANOVA) to examine error dependence on angle of attack, sensor used (inertial or optical). and on tunnel state variables such as Mach number is presented. Experimental comparisons with a high-accuracy indexing table are presented. Small roll angles are found to introduce a zero-shift in the measured angles. It is shown experimentally that. provided the proper constraints necessary for a solution are met, a single- camera solution can he comparable to a 2-camera intersection result. The relative immunity of optical techniques to dynamics is illustrated.

Burner, A. W.↗
NASA NTRS1999

Active Vertical Tail Buffeting Alleviation on an F/A-18 Model in a Wind Tunnel

A 1/6-scale F-18 wind-tunnel model was tested in the Transonic Dynamics Tunnel at the NASA Langley Research Center as part of the Actively Controlled Response Of Buffet-Affected Tails (ACROBAT) program to assess the use of active controls in reducing vertical tail buffeting. The starboard vertical tail was equipped with an active rudder and other aerodynamic devices, and the port vertical tail was equipped with piezoelectric actuators. The tunnel conditions were atmospheric air at a dynamic pressure of 14 psf. By using single-input-single-output control laws at gains well below the physical limits of the control effectors, the power spectral density of the root strains at the frequency of the first bending mode of the vertical tail was reduced by as much as 60 percent up to angles of attack of 37 degrees. Root mean square (RMS) values of root strain were reduced by as much as 19 percent. Stability margins indicate that a constant gain setting in the control law may be used throughout the range of angle of attack tested.

Moses, Robert W.↗
NASA NTRS1964

Oil-smeared models aid wind tunnel measurements

For visualizing flow characteristics in wind tunnel tests, model surfaces are smeared with any common petroleum-base oils. These fluoresce under ultraviolet light and the flow patterns are readily visualized.

Katzoff, S.↗
NASA NTRS2002

Scaling Laws Applied to a Modal Formulation of the Aeroservoelastic Equations

A method of scaling is described that easily converts the aeroelastic equations of motion of a full-sized aircraft into ones of a wind-tunnel model. To implement the method, a set of rules is provided for the conversion process involving matrix operations with scale factors. In addition, a technique for analytically incorporating a spring mounting system into the aeroelastic equations is also presented. As an example problem, a finite element model of a full-sized aircraft is introduced from the High Speed Research (HSR) program to exercise the scaling method. With a set of scale factor values, a brief outline is given of a procedure to generate the first-order aeroservoelastic analytical model representing the wind-tunnel model. To verify the scaling process as applied to the example problem, the root-locus patterns from the full-sized vehicle and the wind-tunnel model are compared to see if the root magnitudes scale with the frequency scale factor value. Selected time-history results are given from a numerical simulation of an active-controlled wind-tunnel model to demonstrate the utility of the scaling process.

Pototzky, Anthony S.↗
NASA NTRS1976

Some experience using subcritical response methods in wind-tunnel flutter model studies

Experiences obtained with four methods of predicting flutter of wind-tunnel models from subcritical response data are described. The four methods are: co/quad, randomdec, power spectra density, and the peak-hold spectrum. Model excitation techniques included both forced (sinusoidal sweep) and random (tunnel turbulence). These methods were successfully used to measure the frequency and damping (or an inverse response amplitude proportional to the damping) in the predominant flutter modes. Implementation and application of each method are discussed. Some results and comparisons between methods are presented.

Foughner, J. T., Jr.↗