Search NASA⌕ Search

SEARCH · Search NASA

Results for “advanced coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Thermal Cyclic Behavior of Thermal and Environmental Barrier Coatings Investigated Under High-Heat-Flux Conditions

Environmental barrier coatings (EBC's) have been developed to protect silicon-carbide- (SiC) based ceramic components in gas turbine engines from high-temperature environmental attack. With continuously increasing demands for significantly higher engine operating temperature, future EBC systems must be designed for both thermal and environmental protection of the engine components in combustion gases. In particular, the thermal barrier functions of EBC's become a necessity for reducing the engine-component thermal loads and chemical reaction rates, thus maintaining the required mechanical properties and durability of these components. Advances in the development of thermal and environmental barrier coatings (TBC's and EBC's, respectively) will directly impact the successful use of ceramic components in advanced engines. To develop high-performance coating systems, researchers must establish advanced test approaches. In this study, a laser high-heat-flux technique was employed to investigate the thermal cyclic behavior of TBC's and EBC's on SiC-reinforced SiC ceramic matrix composite substrates (SiC/SiC) under high thermal gradient and thermal cycling conditions. Because the laser heat flux test approach can monitor the coating's real-time thermal conductivity variations at high temperature, the coating thermal insulation performance, sintering, and delamination can all be obtained during thermal cycling tests. Plasma-sprayed yttria-stabilized zirconia (ZrO2-8 wt% Y2O3) thermal barrier and barium strontium aluminosilicate-based environmental barrier coatings (BSAS/BSAS+mullite/Si) on SiC/SiC ceramic matrix composites were investigated in this study. These coatings were laser tested in air under thermal gradients (the surface and interface temperatures were approximately 1482 and 1300 C, respectively). Some coating specimens were also subject to alternating furnace cycling (in a 90-percent water vapor environment at 1300 C) and laser thermal gradient cycling tests (in air), to investigate the water vapor effect. All cyclic tests were conducted using a 60-min hot-time temperature.

Zhu, Dongming↗
NASA NTRS2003

NASA Glenn/AADC-Rolls Royce Collaborated to Measure Erosion Resistance on Coated Polymer Matrix Composites

Polymer matrix composites (PMCs) are increasingly used in aerospace and automotive applications because of their light weight and high strength-to-weight ratio relative to metals. However, a major drawback of PMCs is poor abrasion resistance, which restricts their use, especially at high temperatures. Simply applying a hard coating on PMCs to improve abrasion and erosion resistance is not effective since coating durability is short lived (ref. 1). Generally, PMCs have higher coefficients of thermal expansion than metallic or ceramic coatings have, and coating adhesion suffers because of poor interfacial adhesion strength. One technique commonly used to improve coating adhesion or durability is the use of bond coats that are interleaved between a coating and a substrate with vastly different coefficients of thermal expansion. An example of this remedy is the use of bondcoats for ceramic thermal barrier coatings on metallic turbine components (ref. 2). Prior collaborative research between the NASA Glenn Research Center and the Allison Advanced Development Company (AADC) demonstrated that bond coats sandwiched between PMCs and high-quality plasma-sprayed, erosion-resistant coatings substantially improved the erosion resistance of PMCs (ref. 3). One unresolved problem in this earlier collaboration was that there was no easy, accurate way to measure the coating erosion wear scar. Coating wear was determined by both profilometry and optical microscopy. Both techniques are time consuming. Wear measurement by optical microscopy requires sample destruction and does not provide a comprehensive measure of the entire wear volume. An even more subtle, yet critical, problem is that these erosion coatings contain two or more materials with different densities. Therefore, simply measuring specimen mass loss before and after erosion will not provide an accurate gauge for coating and/or substrate volume loss. By using a noncontact technique called scanning optical interferometry, which was recently developed at Glenn, researchers can accurately determine the wear performance of erosion-coated PMCs while preserving the sample. An example of this interferometry technique is shown in the preceding figure for an erosion-coated inlet guide vane from a Rolls Royce AE3007 regional gas turbine jet engine. Erosion was conducted with coated and uncoated PMC vanes, with the abrasive material moving at a velocity of 229 m/s at impingement angles of 20 and 90 degrees. The coatings for PMCs remarkably reduced the erosion volume loss by a factor of approximately 10. Currently, several erosion coatings for PMCs are being compared and downselected for engine testing at Rolls Royce.

Miyoshi, Kazuhisa↗
NASA NTRS2003

High-Frequency Testing of Composite Fan Vanes With Erosion-Resistant Coating Conducted

The mechanical integrity of hard, erosion-resistant coatings were tested using the Structural Dynamics Laboratory at the NASA Glenn Research Center. Under the guidance of Structural Mechanics and Dynamics Branch personnel, fixturing and test procedures were developed at Glenn to simulate engine vibratory conditions on coated polymer-matrix- composite bypass vanes using a slip table in the Structural Dynamics Laboratory. Results from the high-frequency mechanical bench testing, along with concurrent erosion testing of coupons and vanes, provided sufficient confidence to engine-endurance test similarly coated vane segments. The knowledge gained from this program will be applied to the development of oxidation- and erosion-resistant coatings for polymer matrix composite blades and vanes in future advanced turbine engines. Fan bypass vanes from the AE3007 (Rolls Royce America, Indianapolis, IN) gas turbine engine were coated by Engelhard (Windsor, CT) with compliant bond coatings and hard ceramic coatings. The coatings were developed collaboratively by Glenn and Allison Advanced Development Corporation (AADC)/Rolls Royce America through research sponsored by the High-Temperature Engine Materials Technology Project (HITEMP) and the Higher Operating Temperature Propulsion Components (HOTPC) project. High-cycle fatigue was performed through high-frequency vibratory testing on a shaker table. Vane resonant frequency modes were surveyed from 50 to 3000 Hz at input loads from 1g to 55g on both uncoated production vanes and vanes with the erosion-resistant coating. Vanes were instrumented with both lightweight accelerometers and strain gauges to establish resonance, mode shape, and strain amplitudes. Two high-frequency dwell conditions were chosen to excite two strain levels: one approaching the vane's maximum allowable design strain and another near the expected maximum strain during engine operation. Six specimens were tested per dwell condition. Pretest and posttest inspections were performed optically at up to 60 magnification and using a fluorescent-dye penetrant. Accumulation of 10 million cycles at a strain amplitude of two to three times that expected in the engine (approximately 670 Hz and 20g) led to the development of multiple cracks in the coating that were only detectable using fluorescent-dye penetrant inspection. Cracks were prevalent on the trailing edge and on the convex side of the midsection. No cracking or spalling was evident using standard optical inspection at up to 60 magnification. Further inspection may reveal whether these fine cracks penetrated the coating or were strictly on the surface. The dwell condition that simulated actual engine conditions produced no obvious surface flaws even after up to 80 million cycles had been accumulated at strain amplitudes produced at approximately 1500 Hz and 45g.

Bowman, Cheryl L.↗
NASA NTRS1982

Method of protecting a surface with a silicon-slurry/aluminide coating

A low cost coating for protecting metallic base system substrates from high temperatures, high gas velocity oxidation, thermal fatigue and hot corrosion is described. The coating is particularly useful for protecting vanes and blades in aircraft and land based gas turbine engines. A lacquer slurry comprising cellulose nitrate containing high purity silicon powder is sprayed onto the superalloy substrates. The silicon layer is then aluminized to complete the coating. The Si-Al coating is less costly to produce than advanced aluminides and protects the substrate from oxidation and thermal fatigue for a much longer period of time than the conventional aluminide coatings. While more expensive Pt-Al coatings and physical vapor deposited MCrAlY coatings may last longer or provide equal protection on certain substrates, the Si-Al coating exceeded the performance of both types of coatings on certain superalloys in high gas velocity oxidation and thermal fatigue. Also, the Si-Al coating increased the resistance of certain superalloys to hot corrosion.

Deadmore, D. L.↗
NASA NTRS1983

Silicon-slurry/aluminide coating

A low cost coating protects metallic base system substrates from high temperatures, high gas velocity ovidation, thermal fatigue and hot corrosion and is particularly useful fo protecting vanes and blades in aircraft and land based gas turbine engines. A lacquer slurry comprising cellulose nitrate containing high purity silicon powder is sprayed onto the superalloy substrates. The silicon layer is then aluminized to complete the coating. The Si-Al coating is less costly to produce than advanced aluminides and protects the substrates from oxidation and thermal fatigue for a much longer period of time than the conventional aluminide coatings. While more expensive Pt-Al coatings and physical vapor deposited MCrAlY coatings may last longer or provide equal protection on certain substrates, the Si-Al coating exceeded the performance of both types of coatings on certain superalloys in high gas velocity oxidation and thermal fatigue and increased the resistance of certain superalloys to hot corrosion.

Deadmore, D. L.↗
NASA NTRS2003

Combined Mode I and Mode II Fracture of Plasma-Sprayed Thermal Barrier Coatings at Ambient and Elevated Temperatures

The mode I, mode II, and combined mode I-mode II fracture behavior of ZrO2 - 8wt%Y2O3 thermal barrier coatings was determined in asymmetric flexure loading at both ambient and elevated temperatures. Precracks were introduced in test specimens using the single-edge-v-notched beam (SEVNB) method incorporated with final diamond polishing to achieve sharp crack tips. A fracture envelope of KI versus KII was determined for the coating material at ambient and elevated temperatures. Propagation angles of fracture as a function of KI/KII were also determined. The mixed-mode fracture behaviors of the coating material were compared with those of monolithic advanced ceramics determined previously. The mixed-mode fracture behavior of the plasma- sprayed thermal barrier coating material was predicted in terms of fracture envelope and propagation angle using mixed-mode fracture theories.

Choi, Sung R.↗
NASA NTRSDate not supplied

Advanced TUFROC Thermal Protection System Evolution Under Re-entry like Conditions

Toughened Unipiece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) and its successor, Advanced TUFROC, are state-of-the-art thermal protection systems (TPS) for high temperature reusable applications. Originally designed for use on the wing-leading edge of X-37B, TUFROC is an insulative tiled system consisting of a low-conductivity ceramic base, a carbonaceous cap, and multiple coatings for thermal performance. The improved Advanced TUFROC has demonstrated reusability up to 2900 °F and single use capabilities exceeding 3200 °F. This effort explores the evolution of Advanced TUFROC when exposed to re-entry like conditions via arc jet testing. Chemical reactions and constituent migration resulting from the aerothermal heating are known to occur and are studied in detail. Further, the interaction between the multiple constituents and layers will be discussed as this is believed to have a significant impact on the overall performance. Characterization includes structural analysis via optical microscopy, scanning electron microscopy and energy-dispersive x-ray spectroscopy.

Thermal protection system↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative (MERCRII)

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity. These alloys, however, exhibit poor tribological response (high friction and wear) in extreme space environments and are exacerbated by the presence of lunar regolith. This leads to a shortened service life that poses a challenge for long term operations on the lunar surface. This project seeks to address this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the lifetime and sustainability of both lunar and Martian assets and the missions they support.

dust mitigation↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗
NASA NTRS2003

Combined Mode I and Mode II Fracture of Plasma-Sprayed Thermal Barrier Coatings at Ambient and Elevated Temperatures

The mode I, mode II, and combined mode I-mode II fracture behavior of ZrO2- 8wt%Y2O3 thermal barrier coatings was determined in asymmetric flexure loading at both ambient and elevated temperatures. Precracks were introduced in test specimens using the single-edge-v-notched beam (SEVNB) method incorporated with final diamond polishing to achieve sharp crack tips. A fracture envelope of KI versus KII was determined for the coating material at ambient and elevated temperatures. Propagation angles of fracture as a function of K(sub I)/K(sub II) were also determined. The mixed-mode fracture behaviors of the coating material were compared with those of monolithic advanced ceramics determined previously. The mixed-mode fracture behavior of the plasma-sprayed thermal barrier coating material was predicted in terms of fracture envelope and propagation angle using mixed-mode fracture theories.

Choi, Sung R.↗
NASA NTRSDate not supplied

Protective Coatings for Mitigating Lunar Dust Abrasion and Adhesion

Materials resistant to the harsh lunar environment are needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust poses a significant threat to the durability of components and vehicles due to its fine, jagged morphology and highly abrasive nature. These characteristics result in particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this work is to identify and characterize wear-resistant materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Results from testing and evaluation methods devised to elucidate and mimic aspects of lunar dust degradation, including adhesion, abrasion and erosion, as well as the lunar environment, will be presented. Discussion on balancing the need for dust management and tolerance versus dust adhesion mitigation will be shared in context of relevant lunar applications within the NASA Lunar Occupancy Dust Surface Separation Technologies effort, which is part of a NASA-wide effort to enable a sustained lunar presence through the Lunar Surface Innovation Initiative.

lunar dust mitigation↗
NASA NTRS2023

Protective Coatings for Lunar Dust Tolerance

Materials capable of withstanding the harsh lunar environment are critically needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust significantly threatens the durability and reusability of components and vehicles due to possessing a fine, jagged morphology and highly abrasive nature. These characteristics result in the particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this study is to identify and characterize wear-resistant commercial-off-the-shelf (COTS) materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Preliminary testing that mimics various aspects of lunar dust degradation, such as abrasive wear and adhesion, suggests that COTS ceramic coatings can improve lunar dust tolerance and protect underlying metallic substrates.

Valerie. L. Wiesner↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative (MERCRII)

Mission concepts such as JPL’s Endurance-A utilize rovers such as Astrolab’s FLEX concept to explore the lunar surface. For these types of systems, lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified to minimize mass while maintaining structural integrity. Such alloys, however, exhibit poor tribological response in the form of high friction and wear, especially in extreme space environments and with the additional presence of lunar regolith. This shortens the lifetimes of these systems which have a requirement to traverse 1,00km/year. This project is addressing the technology need of this and future rover missions by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the lifetime and sustainability of both lunar and Martian assets.

MISSE↗
NASA NTRS1992

Advanced liquid rockets

A program to substitute iridium coated rhenium for silicide coated niobium in thrust chamber fabrications is reviewed. The life limiting phenomena in each of these material systems is also reviewed. Coating cracking and spalling is not a problem with iridium-coated rhenium as in silicide-coated niobium. Use of the new material system enables an 800 K increase in thruster operating temperature from around 1700 K for niobium to 2500 K for rhenium. Specific impulse iridium-coated rhenium rockets is nominally 20 seconds higher than comparable niobium rockets in the 22 N class and nominally 10 seconds higher in the 440 N class.

Schneider, Steven J.↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative Under Extreme Space Environments

Mission concepts such as JPL’s Endurance-A campaign will utilize rovers such as Astrolab’s FLEX concept to explore the lunar surface. For these types of systems, lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified to minimize mass while maintaining structural integrity [1,2,3]. Such alloys, however, exhibit poor tribological response in the form of high friction and wear, especially in extreme space environments and with the additional presence of lunar regolith. This shortens the lifetimes of these systems which have a requirement to traverse 1,00km/year [2,3]. The MERCRII project is ad-dressing the technology need of this and future rover missions by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the lifetime and sustainability of both lunar and Martian assets. The MERCRII project focuses on the technology taxonomies of exploration destination systems, mission infrastructure, and sustainability and supportability to explore both new and existing coating technologies, including material formulations and application methods. Several material formulations were considered for their wear resistance and fracture toughness and the following were chosen for Phase I testing: Nickle Titani-um (NiTi), Aluminum Oxide (AlO), and Ti64 with hBN at two and ten vol percent (Ti-2vol%hBN and Ti-10vol%hBN).

S. Rengifo↗
NASA NTRS2007

Modeling Creep-Induced Stress Relaxation at the Leading Edge of SiC/SiC Airfoils

Anticipating the implementation of advanced SiC/SiC composites into internally cooled airfoil components within the turbine section of future aero-propulsion engines, the primary objective of this study was to develop physics-based analytical and finite-element modeling tools to predict the effects of composite creep and stress relaxation at the airfoil leading edges, which will generally experience large thermal gradients at high temperatures. A second objective was to examine how some advanced NASA-developed SiC/SiC systems coated with typical EBC materials would behave as leading edge materials in terms of long-term steady-state operating temperatures. Because of the complexities introduced by mechanical stresses inherent in internally cooled airfoils, a simple cylindrical thin-walled tube model subjected to thermal stresses only is employed for the leading edge, thereby obtaining a best-case scenario for the material behavior. In addition, the SiC/SiC composite materials are assumed to behave as isotropic materials with temperature-dependent viscoelastic creep behavior as measured in-plane on thin-walled panels. Key findings include: (1) without mechanical stresses and for typical airfoil geometries, as heat flux is increased through the leading edge, life-limiting tensile crack formation will occur first in the hoop direction on the inside wall of the leading edge; (2) thermal gradients through all current SiC/SiC systems should be kept below approx.300 F at high temperatures to avoid this cracking; (3) at temperatures near the maximum operating temperatures of advanced SiC/SiC systems, thermal stresses induced by the thermal gradients will beneficially relax with time due to creep; (4) although stress relaxation occurs, the maximum gradient should still not exceed 300oF because of residual tensile stress buildup on the airfoil outer wall during cool-down; and (5) without film cooling and mechanical stresses, the NASA-developed N26 SiC/SiC system with thru-thickness Sylramic-iBN fiber reinforcement and a typical EBC coating has the potential of offering a maximum long-term steady-state operating temperature of approx.3100 F at the surface of the EBC.

Lang, Jerry↗
NASA NTRS2015

A Future Large-Aperture UVOIR Space Observatory: Key Technologies and Capabilities

We present the key technologies and capabilities that will enable a future, large-aperture ultravioletopticalinfrared (UVOIR) space observatory. These include starlight suppression systems, vibration isolation and control systems, lightweight mirror segments, detector systems, and mirror coatings. These capabilities will provide major advances over current and near-future observatories for sensitivity, angular resolution, and starlight suppression. The goals adopted in our study for the starlight suppression system are 10-10 contrast with an inner working angle of 20 milliarcsec and broad bandpass. We estimate that a vibration and isolation control system that achieves a total system vibration isolation of 140 dB for a vibration-isolated mass of 5000 kg is required to achieve the high wavefront error stability needed for exoplanet coronagraphy. Technology challenges for lightweight mirror segments include diffraction-limited optical quality and high wavefront error stability as well as low cost, low mass, and rapid fabrication. Key challenges for the detector systems include visible-blind, high quantum efficiency UV arrays, photon counting visible and NIR arrays for coronagraphic spectroscopy and starlight wavefront sensing and control, and detectors with deep full wells with low persistence and radiation tolerance to enable transit imaging and spectroscopy at all wavelengths. Finally, mirror coatings with high reflectivity ( 90), high uniformity ( 1) and low polarization ( 1) that are scalable to large diameter mirror substrates will be essential for ensuring that both high throughput UV observations and high contrast observations can be performed by the same observatory.

Instrument↗
NASA NTRS2005

Characterization of Cold Sprayed CuCrAl Coated GRCop-84 Substrates for Reusable Launch Vehicles

An advanced Cu-8(at.%)Cr-4%Nb alloy developed at NASA's Glenn Research Center, and designated as GRCop-84, is currently being considered for use as combustor liners and nozzles in NASA's future generations of reusable launch vehicles (RLVs). Despite the fact that this alloy has superior mechanical and oxidation properties compared to many commercially available copper alloys, it is felt that its high temperature and environmental resistance capabilities can be further enhanced with the development and use of suitable coatings. Several coatings and processes are currently being evaluated for their suitability and future down selection. A newly developed CuCrAl has shown excellent oxidation resistance compared to current generation Cu-Cr coating alloys. Cold spray technology for depositing the CuCrAl coating on a GRCop-84 substrate is currently being developed under NASA's Next Generation Launch Technology (NGLT) Propulsion Research and Technology (PR&T) project. The microstructures, mechanical and thermophysical properties of overlay coated GRCop-84 substrates are discussed.

Raj, S . V.↗