Search NASA⌕ Search

SEARCH · Search NASA

Results for “airplane capabilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Fielding An Amphibious UAV: Development, Results, and Lessons Learned

This report summarizes the work completed on the design and flight-testing of a small, unmanned, amphibious demonstrator aircraft that flies autonomously. The aircraft named ACAT (Autonomous Cargo Amphibious Transport) is intended to be a large cargo carrying unmanned aircraft that operates from water to avoid airspace and airfield conflict issues between manned and unmanned aircraft. To demonstrate the feasibility of this concept, a demonstrator ACAT was designed, built, and flown that has a six-foot wingspan and can fly autonomously from land or water airfield. The demonstrator was designed for a 1-hour duration and 1-mile telemetry range. A sizing code was used to design the smallest demonstrator UAV to achieve these goals. The final design was a six-foot wingspan, twin hull configuration that distributes the cargo weight across the span, reducing the wing structural weight. The demonstrator airframe was constructed from balsa wood, fiberglass, and plywood. A 4-stroke model airplane engine powered by methanol fuel was mounted in a pylon above the wing and powers the ACAT UAV. Initial flight tests from land and water were conducted under manual radio control and confirmed the amphibious capability of the design. Flight avionics that were developed by MLB for production UAVs were installed in the ACAT demonstrator. The flight software was also enhanced to permit autonomous takeoff and landing from water. A complete autonomous flight from ahard runway was successfully completed on July 5, 2001 and consisted of a take-off, rectangular flight pattern, and landing under complete computer control. A completely autonomous flight that featured a water takeoff and landing was completed on October 4, 2001. This report describes these activities in detail and highlights the challenges encountered and solved during the development of the ACAT demonstrator. hard runway was successfully completed on July 5, 2001 and consisted of a take-off, rectangular flight pattern, and landing under complete computer control. A completely autonomous flight that featured a water takeoff and landing was completed on October 4, 2001. This report describes these activities in detail and highlights the challenges encountered and solved during the development of the ACAT demonstrator.

Pisanich, Greg↗
NASA NTRS1966

Summary of NASA Support of the F-111 Development Program: December 1962 - December 1965 - Part 1

The F-111 is a biservice, multimission, tactical aircraft being developed for the Air Force and Navy by General Dynamics and Grumman. The general arrangement of the F-111 is shown in figure 1. This aircraft, through the use of the "variable sweep wing" concept, offers the possibility of combining a wide range of mission capabilities into a single aircraft. The F-111 is a direct outgrowth of the Langley Research Center's variable sweep research which began in 1947. The early research culminated in the X-5 variable sweep research airplane which demonstrated the advantage and feasibility of in-flight sweep variation~ The X-5 utilized the translating wing concept to offset the longitudinal stability variation with sweep changes. Later Langley research beginning in 1958 resulted in the "outboard pivot" concept which eliminated the need for wing translation and led .to the TFX (F-111) concept. A chronology of the NACA/NASA variable sweep research effort and direct su~port of the TFX up to the awarding of the contract to General Dynamics/Grumman on November 24, 1962, is presented in refer'ence 1. Since the awarding of the contract, the Langley, Ames, Lewis, and Flight Research Centers have been actively supporting the F-111 development program. Because of the strong NASA interest in this aircraft and the large magnitude of NASA support involved, it was felt desirable to document this support. The purpose of this paper therefore is to present a brief summary of the NASA support, in chronological order, through December 1965, beginning with the awarding of the contract in November 1962.

Source record↗
NASA NTRS1994

Simplified Aerodynamic and Structural Modeling for Oblique All-Wing Aircraft. Phase 2: Structures

Any aircraft preliminary design study requires a structural model of the proposed configuration. The model must be capable of estimating the structural weight of a given configuration, and of predicting the deflections which will result from foreseen flight and ground loads. The present work develops such a model for the proposed Oblique All Wing airplane. The model is based on preliminary structural work done by Jack Williams and Peter Rudolph at Mdng, and is encoded in a FORTRAN program. As a stand-alone application, the program can calculate the weight CG location, and several types of structural deflections; used in conjunction with an aerodynamics model, the program can be used for mission analysis or sizing studies.

Kroo, Ilan↗
NASA NTRS1983

Comparison of Results Obtained from Flight Tests and Simulated Tests of a Digital Electronic Engine Control System in an F-15 Airplane

Substantial benefits of a full authority digital electronic engine control on an air breathing engine were demonstrated repeatedly in simulation studies, ground engine tests, and engine altitude test facilities. A digital engine electronic control system showed improvements in efficiency, performance, and operation. An additional benefit of full authority digital controls is the capability of detecting and correcting failures and providing engine health diagnostics.

Myers, Lawrence P.↗
NASA NTRS1984

Digital Electronic Engine Control (DEEC) Flight Evaluation in an F-15 Airplane

Flight evaluation in an F-15 aircraft by digital electronic engine control (DEEC) was investigated. Topics discussed include: system description, F100 engine tests, effects of inlet distortion on static pressure probe, flight tests, digital electronic engine control fault detection and accommodation flight evaluation, flight evaluation of a hydromechanical backup control, augmentor transient capability of an F100 engine, investigation of nozzle instability, real time in flight thrust calculation, and control technology for future aircraft propulsion systems. It is shown that the DEEC system is a powerful and flexible controller for the F100 engine.

Source record↗
NASA NTRS1973

A study to determine the feasibility of a low sonic boom supersonic transport.

The objective of this study was to determine if a supersonic transport designed to produce a sonic boom signature with low overpressure represented a feasible concept. Two design goals were chosen: an overpressure of 1.0 psf or less for cruise at Mach 2.7 and an overpressure of 0.5 psf for cruise at Mach 1.5. Projected 1985 technology was assumed for the analysis. The principal effort was to develop cruise configurations capable of meeting the sonic boom goals. The Mach 2.7 goal was achieved with a blended arrow wing configuration and the Mach 1.5 design was a low arrow wing configuration with a horizontal tail. The development of these airplanes is summarized and the concept of a low sonic boom SST is evaluated.

Kane, E. J.↗
NASA NTRS1993

Automated Finite Element Modeling of Wing Structures for Shape Optimization

The displacement formulation of the finite element method is the most general and most widely used technique for structural analysis of airplane configurations. Modem structural synthesis techniques based on the finite element method have reached a certain maturity in recent years, and large airplane structures can now be optimized with respect to sizing type design variables for many load cases subject to a rich variety of constraints including stress, buckling, frequency, stiffness and aeroelastic constraints (Refs. 1-3). These structural synthesis capabilities use gradient based nonlinear programming techniques to search for improved designs. For these techniques to be practical a major improvement was required in computational cost of finite element analyses (needed repeatedly in the optimization process). Thus, associated with the progress in structural optimization, a new perspective of structural analysis has emerged, namely, structural analysis specialized for design optimization application, or.what is known as "design oriented structural analysis" (Ref. 4). This discipline includes approximation concepts and methods for obtaining behavior sensitivity information (Ref. 1), all needed to make the optimization of large structural systems (modeled by thousands of degrees of freedom and thousands of design variables) practical and cost effective.

Harvey, Michael Stephen↗
NASA NTRS1987

Flutter study of an advanced composite wing with external stores

A flutter test using a scaled model of an advanced composite wing for a Navy attack aircraft has been conducted in the NASA Langley Research Center Transonic Dynamics Tunnel. The model was a wall-mounted half-span wing with a semi-span of 6.63 ft. The wing had an aspect ratio of 5.31, taper ratio of 0.312, and quarter-chord sweep of 25 degrees. The model was supported in a manner that simulated the load path in the carry-through structure of the aircraft and the symmetric boundary condition at the fuselage centerline. The model was capable of carrying external stores from three pylon locations on the wing. Flutter tests were conducted for the wing with and without external stores. No flutter was encountered for the clean wing at test conditions which simulated the scaled airplane operating envelope. Flutter boundaries were obtained for several external store configurations. The flutter boundaries for the fuel tanks were nearly Mach number independent (occurring at constant dynamic pressure). To study the aerodynamic effect of the fuel tank stores, pencil stores (slender cylindrical rods) which had the same mass and pitch and yaw inertia as the fuel tanks were tested on the model. These pencil store configurations exhibited a transonic dip in the flutter dynamic pressure, indicating that the aerodynamic effect of the actual fuel tanks on flutter was significant. Several flutter analyses methods were used in an attempt to predict the flutter phenomenon exhibited during the wind-tunnel test. The analysis gave satisfactory predictions of flutter for the pencil store configurations, but unsatisfactory correlation for the actual fuel tank configurations.

Cole, Stanley R.↗
NASA NTRS1992

Temperature/pressure and water vapor sounding with microwave spectroscopy

Two intense microwave spectra lines exist in the martian atmosphere that allow unique sounding capabilities: water vapor at 183 GHz and the (2-1) rotational line of CO at 230 GHz. Microwave spectra line sounding is a well-developed technique for the Earth's atmosphere for sounding from above from spacecraft and airplanes, and from below from fixed surface sites. Two simple instruments for temperature sounding on Mars (the CO line) and water vapor measurements are described. The surface sounder proposed for the MESUR sites is designed to study the boundary layer water vapor distribution and the temperature/pressure profiles with vertical resolution of 0.25 km up to 1 km with reduced resolution above approaching a scale height. The water channel will be sensitive to a few tenths of a micrometer of water and the temperature profile will be retrieved to an accuracy between 1 and 2 K. The latter is routinely done on the Earth using oxygen lines near 60 GHz. The measurements are done with a single-channel heterodyne receiver looking into a 10-cm mirror that is canned through a range of elevation angles plus a target load. The frequency of the receiver is sweep across the water and CO lines generating the two spectra at about 1-hr intervals throughout the mission. The mass and power for the proposed instrument are 2 kg and 5-8 W continuously. The measurements are completely immune to the atmospheric dust and ice particle loads. It was felt that these measurements are the ultimate ones to properly study the martian boundary layer from the surface to a few kilometers. Sounding from above requires an orbiting spacecraft with multichannel microwave spectrometers such as the instrument proposed for MO by a subset of the authors, a putative MESUR orbiter, and a proposed Discovery mission called MOES. Such an instrument can be built with less than 10 kg and use less than 15 W. The obvious advantage of this approach is that the entire atmosphere can be sounded for temperature and water vapor in a few hours with somewhat better than a scale height resolution. If a bigger mirror is used (greater than 30 cm) limb sounding geometry can be employed and half scale height resolution achieved to altitudes up to at least 60 km. Again, the measurements are immune to dust and ice loads. Water vapor sensitivity of 0.1 micrometer can be achieved (even with a nadir instrument) and temperature profiles retrieved to an accuracy of better than 2 K from the surface to about 60 km. Winds can be measured from the doppler shifts of CO lines in the limb sounding mode.

Muhleman, D. O.↗
NASA NTRS1950

Free-Spinning-Tunnel Investigation of a 1/30-Scale Model of the Grumman XF1OF-1 Airplane

An investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/30 - scale model of the Grumman XFlOF-1 airplane to determine its spin and recovery characteristics. The investigation included erect and inverted spins for both the straight-wing and swept-wing configurations. Tests to determine the optimum size spin-recovery parachutes and the rudder forces required for recovery were also made. The results indicated that in the straight-wing configuration, satisfactory recoveries of the airplane will be obtained from erect and inverted spins by rudder reversal alone. In the swept-wing configuration recoveries will be unsatisfactory from erect spins. Unsweeping the wings during the spin and reversal of the rudder, however, will lead to eventual recovery. The test results also indicated that, if existing small ailerons are made deflectable through large angles, satisfactory recoveries will be obtained from erect spins in the swept-wing configuration by simultaneous movement of the rudder to against the spin and movement of the ailerons to with the spin. Normal-size ailerons deflected through a normal range would also be effective. Satisfactory recoveries by rudder reversal will be obtained from inverted spins in the swept-wing configuration. In the straight-wing configuration a 14.2-foot tail parachute or a 5.0-foot wing-tip parachute opened on the outer wing tip will effect satisfactory recovery of the airplane by parachute action alone; a 30.0-foot tail parachute or a 10.0-foot wing-tip parachute will be required for the swept-wing configuration. The forces required to fully reverse the rudder should be within the capabilities of the pilot.

Berman, Theodore↗
NASA NTRS2015

Introduction to Autogyros, Helicopters, and Other V/STOL Aircraft Volume III: Other V/STOL Aircraft

The period from Ciervas demonstration of his C.6A Autogiro in Farnborough, England, in October 1925, up to when Pan American World Airways ushered in jet age service to Europe with a Boeing 707-120 on October 26, 1958, was one of enormous progress in the aviation world. This progress was made primarily in the fixed-wing world. This 33-year period saw the conventional takeoff and landing (CTOL) machine achieve increases in cruise speed, range, cruise altitude, and number of passengers carried. These improvements were not, however, accompanied by reductions in takeoff and landing space required. In fact, just the opposite occurred. And with the arrival of the autogyro, and then the helicopter, fixed-wing advocates were presented with a clear challenge to fix the airplanes major shortcomings stalling and loss of control at low speed. I do not think airplane advocates felt particularly threatened by autogyros in the late 1920s because it quickly became apparent that the cruise performance of these short takeoff and landing (STOL) aircraft would never become competitive. Even the vertical takeoff and landing (VTOL) capability offered by the helicopter was relegated to a niche market. Fixed-wing advocates felt (and still feel, in my opinion) that helicopters would never take much of the traveling publics business away from their major civil airlines or trains, buses, cars, or ships for that matter. Understanding the fundamental performance problem of the CTOL is a prerequisite to learning about VTOLs and STOLs. Therefore, let me use this introduction to set the stage for an in-depth discussion of vertical and short takeoff and landing (VSTOL) aircraft.

Harris, Franklin Dewitt↗
NASA NTRS1983

Flight evaluation of modifications to a digital electronic engine control system in an F-15 airplane

The third phase of a flight evaluation of a digital electronic engine control system in an F-15 has recently been completed. It was found that digital electronic engine control software logic changes and augmentor hardware improvements resulted in significant improvements in engine operation. For intermediate to maximum power throttle transients, an increase in altitude capability of up to 8000 ft was found, and for idle to maximum transients, an increase of up to 4000 ft was found. A nozzle instability noted in earlier flight testing was investigated on a test engine at NASA Lewis Research Center, a digital electronic engine control software logic change was developed and evaluated, and no instability occurred in the Phase 3 flight evaluation. The backup control airstart modification was evaluated, and gave an improvement of airstart capability by reducing the minimum airspeed for successful airstarts by 50 to 75 knots.

Burcham, F. W., Jr.↗
NASA NTRS1983

Flight evaluation of modifications to a digital electronic engine control system in an F-15 airplane

The third phase of a flight evaluation of a digital electronic engine control system in an F-15 has recently been completed. It was found that digital electronic engine control software logic changes and augmentor hardware improvements resulted in significant improvements in engine operation. For intermediate to maximum power throttle transients, an increase in altitude capability of up to 8000 ft was found, and for idle to maximum transients, an increase of up to 4000 ft was found. A nozzle instability noted in earlier flight testing was investigated on a test engine at NASA Lewis Research Center, a digital electronic engine control software logic change was developed and evaluated, and no instability occurred in the Phase 3 flight evaluation. The backup control airstart modification was evaluated, and gave an improvement of airstart capability by reducing the minimum airspeed for successful airstarts by 50 to 75 knots.

Burcham, F. W., Jr.↗
NASA NTRS1980

Accuracy of aircraft velocities from inertial navigation systems for application to airborne wind measurements

An experimental assessment was made of two commercially available inertial navigation systems (INS) with regard to their velocity measuring capability for use in wind, shear, and long-wavelength atmospheric turbulence research. The assessment was based on 52 sets of postflight measurements of velocity (error) during a "Schuler cycle" (84 minutes) while the INS was still operating but the airplane was motionless. Four INS units of one type and two units of another were tested over a period of 2 years after routine research flights similar to air-linetype operations of from 1 to 6 hours duration. The maximum postflight errors found for the 52 cases had a root mean square value of 2.82 m/sec with little or no correlation of error magnitude with flight duration. Using an INS for monitoring ground speed during landway in a predicted high wind shear situation could lead to landing speeds which are dangerously high or low.

Rhyne, R. H.↗
NASA NTRS2008

NASA Langley's AirSTAR Testbed: A Subscale Flight Test Capability for Flight Dynamics and Control System Experiments

As part of the Airborne Subscale Transport Aircraft Research (AirSTAR) project, NASA Langley Research Center (LaRC) has developed a subscaled flying testbed in order to conduct research experiments in support of the goals of NASA s Aviation Safety Program. This research capability consists of three distinct components. The first of these is the research aircraft, of which there are several in the AirSTAR stable. These aircraft range from a dynamically-scaled, twin turbine vehicle to a propeller driven, off-the-shelf airframe. Each of these airframes carves out its own niche in the research test program. All of the airplanes have sophisticated on-board data acquisition and actuation systems, recording, telemetering, processing, and/or receiving data from research control systems. The second piece of the testbed is the ground facilities, which encompass the hardware and software infrastructure necessary to provide comprehensive support services for conducting flight research using the subscale aircraft, including: subsystem development, integrated testing, remote piloting of the subscale aircraft, telemetry processing, experimental flight control law implementation and evaluation, flight simulation, data recording/archiving, and communications. The ground facilities are comprised of two major components: (1) The Base Research Station (BRS), a LaRC laboratory facility for system development, testing and data analysis, and (2) The Mobile Operations Station (MOS), a self-contained, motorized vehicle serving as a mobile research command/operations center, functionally equivalent to the BRS, capable of deployment to remote sites for supporting flight tests. The third piece of the testbed is the test facility itself. Research flights carried out by the AirSTAR team are conducted at NASA Wallops Flight Facility (WFF) on the Eastern Shore of Virginia. The UAV Island runway is a 50 x 1500 paved runway that lies within restricted airspace at Wallops Flight Facility. The facility provides all the necessary infrastructure to conduct the research flights in a safe and efficient manner. This paper gives a comprehensive overview of the development of the AirSTAR testbed.

Jordan, Thomas L.↗
NASA NTRS1980

Study for conceptual design of VEO, VTOL exhaust nozzle

Design requirements for a VEO Wing V/STOL exhaust nozzle with a two dimensional shape and having the capability for upper surface blowing, spanwise blowing, and 90 deg turning of the exhaust flow for VTOL were established. A preliminary design of the nozzle that identified the actuation scheme, key dimensions, the flowpath, and the recommended materials were prepared. The airplane characteristics resulting from integrating the study nozzle were established.

Bittrick, W. C.↗
NASA NTRS1993

Effect of geometry, static stability, and mass distribution on the tumbling characteristics of generic flying-wing models

Results from an investigation to determine the low-speed tumbling characteristics of twelve generic flying-wing models are summarized. There is a concern that airplanes with flying-wing planforms could inadvertently enter an out-of-control tumbling motion under certain conditions. The objectives of this investigation were to: 1) identify the geometric and mass-related parameters that cause flying wings to be capable of sustained tumbling, 2) analyze some of the driving mechanisms that cause tumbling, and 3) determine the feasibility of using computer simulations to predict the tumbling characteristics of flying wings. Free-tumble and free-to-pitch tests were conducted with dynamically-scaled, generic flying wing models. The use of computer simulations as a predictive tool for tumbling was explored. Results indicated that center-of-gravity location, mass distribution, and geometric aspect ratio strongly affected the tumbling characteristics of the models tested and that positive static stability did not necessarily preclude tumbling. The magnitude of dynamic effects were found to be of the same order as static effects for the models undergoing autorotation-in-pitch. The simulations indicated that the dynamic terms in the equations of motion used to predict tumbling must be obtained using experimental methods that account for the large amplitude/high pitch-rate environment that characterizes tumbling.

Fremaux, C. M.↗
NASA NTRS2019

Aeroacoustic Measurements of the Bell 699 Rotor on the Tiltrotor Test Rig in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The Tiltrotor Test Rig (TTR) with the Bell 699 Rotor was tested in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel from 2017 to 2018. The primary goal of the test was to understand the operational capabilities of the TTR while also acquiring research data, including acoustic data. A data quality study revealed that the NFAC 40- by 80-Foot Wind Tunnel is an adequate acoustic environment to test the Bell 699 Rotor for helicopter, conversion, and airplane configurations. Representative acoustic data are presented, and selected acoustic data and corresponding test conditions are included.

Schatzman, N. L.↗