Search NASA⌕ Search

SEARCH · Search NASA

Results for “anisotropic materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

A Study of Time-dependent and Anisotropic Effects on the Deformation Response of Two Flywheel Designs

The influence of material time dependency and anisotropy in the context of two specific flywheel designs-preload and multi-directional composite (MDC)--is investigated. In particular, we focus on the following aspects: 1) geometric constraints, 2) material constraints, 3) loading type, and 4) the fundamental character of the time-dependent response, i.e., reversible or irreversible. The bulk of the results presented were obtained using a composite (PMC IM7/8552 at 135 C) material system. The material was characterized using a general multimechanism hereditary (viscoelastoplastic) model. As a general conclusion, the results have clearly shown that both the preload and the MDC rotor designs are significantly affected by time-dependent material behavior, which may impact the state of rotor balance and potentially reduce its operating life. In view of the results of the parametric studies and predictions made in the present study, the need for actual experimentation focusing on the time-dependent behavior of full-scale flywheel rotors is self-evident.

Saleeb, Atef F.↗
NASA NTRS1992

Failure analysis of thick composite cylinders under external pressure

Failure of thick section composites due to local compression strength and overall structural instability is treated. Effects of material nonlinearity, imperfect fiber architecture, and structural imperfections upon anticipated failure stresses are determined. Comparisons with experimental data for a series of test cylinders are described. Predicting the failure strength of composite structures requires consideration of stability and material strength modes of failure using linear and nonlinear analysis techniques. Material strength prediction requires the accurate definition of the local multiaxial stress state in the material. An elasticity solution for the linear static analysis of thick anisotropic cylinders and rings is used herein to predict the axisymmetric stress state in the cylinders. Asymmetric nonlinear behavior due to initial cylinder out of roundness and the effects of end closure structure are treated using finite element methods. It is assumed that local fiber or ply waviness is an important factor in the initiation of material failure. An analytical model for the prediction of compression failure of fiber composites, which includes the effects of fiber misalignments, matrix inelasticity, and multiaxial applied stresses is used for material strength calculations. Analytical results are compared to experimental data for a series of glass and carbon fiber reinforced epoxy cylinders subjected to external pressure. Recommendations for pretest characterization and other experimental issues are presented. Implications for material and structural design are discussed.

Caiazzo, A.↗
NASA NTRS2004

Material Modeling of Space Shuttle Leading Edge and External Tank Materials For Use in the Columbia Accident Investigation

Upon the commencement of the analytical effort to characterize the impact dynamics and damage of the Space Shuttle Columbia leading edge due to External Tank insulating foam, the necessity of creating analytical descriptions of these materials became evident. To that end, material models were developed of the leading edge thermal protection system, Reinforced Carbon Carbon (RCC), and a low density polyurethane foam, BX-250. Challenges in modeling the RCC include its extreme brittleness, the differing behavior in compression and tension, and the anisotropic fabric layup. These effects were successfully included in LS-DYNA Material Model 58, *MAT_LAMINATED_ COMPOSITE_ FABRIC. The differing compression and tension behavior was modeled using the available damage parameters. Each fabric layer was given an integration point in the shell element, and was allowed to fail independently. Comparisons were made to static test data and coupon ballistic impact tests before being utilized in the full scale analysis. The foam's properties were typical of elastic automotive foams; and LS-DYNA Material Model 83, *MAT_FU_CHANG_FOAM, was successfully used to model its behavior. Material parameters defined included strain rate dependent stress-strain curves for both loading and un-loading, and for both compression and tension. This model was formulated with static test data and strain rate dependent test data, and was compared to ballistic impact tests on load-cell instrumented aluminum plates. These models were subsequently utilized in analysis of the Shuttle leading edge full scale ballistic impact tests, and are currently being used in the Return to Flight Space Shuttle re-certification effort.

Carney, Kelly↗
NASA NTRS1990

Elliptical flux vortices in polycrystalline YBa2Cu3O7

The formation of an Abrikosov flux vortex with its core axis perpendicular to an anisotropic (a-c or b-c) plane in YBa2Cu3O7 requires only 1/10 of the energy required by the formation of a vortex with its core axis perpendicular to an isotropic (a-b) plane. It is not unusual for 18 to 35 percent of shake and bake bulk YBa2Cu3O7 to consist of empty pockets or voids inside the material. Studies estimate that 75 percent of the internal grain boundaries contain a-b planes. If many of the a-b planes are incident upon other grains, then many of the a-c and/or b-c planes must be incident on the voids. Evidently there are a large number of exposed anisotropic planes inside the bulk material. This condition is conducive to the formation of vortices that are perpendicular to the anisotropic planes. The magnetic flux density around such a vortex is constant along contour lines that are elliptical in shape, while the circulating supercurrent density must vary in magnitude along the same contour lines. The impact of this elliptical structure on the possibility of a Kosterlitz-Thouless type phase transition as the bulk material goes from superconducting to normal conducting is discussed. Implications with regard to the excess low frequency electrical noise that occurs at the temperature induced transition are also examined.

Hickman, H.↗
NASA NTRS1985

Importance of anisotropic bending stiffnesses on buckling of symmetrically laminated composite plates loaded in compression

The differential equation governing buckling of symmetrically laminated composite plates loaded in compression is presented in nondimensional form. From this equation, nondimensional material coefficients are obtained and a nondimensional parameter is presented that is used to assess when anisotropic bending stiffnesses can be neglected in a buckling analysis. Results obtained using finite element analyses are presented that show how boundary conditions, aspect ratio, fiber orientation, stacking sequence, and thickness affect the importance of the anisotropic bending stiffnesses.

Nemeth, M. P.↗
NASA NTRSDate not supplied

TPS Certification by Analysis: Model-Driven Characterization of Properties and Failure in Woven Thermal Protection Systems

Woven, ablative thermal protection system (TPS) materials provide a robust option for aggressive (re)entries and thus have been baselined for the upcoming Mars Sample Return (MSR) mission's Earth Entry System (EES). The reliability requirements for MSR-EES necessitate understanding of material property variability, which could be significant given the complex structure and anisotropic nature of properties in TPS weaves, as well as the response to potential impact with micrometeoroids or orbital debris during the EES re-entry. The TPS Certification by Analysis effort within the Entry Systems Modeling project seeks to provide computational models and analyses that support the certification against such material-based risks. For the present talk, focus will be given to the characterization of baseline woven TPS material properties and mechanical failure limits, which entails (1) use of computational techniques (e.g., machine learning) to interpret computed tomography images of the weave to generate representative structural models and (2) application of multiscale material modeling approaches to characterize thermomechanical and failure properties.

thermal protection systems↗
NASA NTRSDate not supplied

TPS Certification by Analysis: Model-Driven Characterization of Properties and Failure in Woven Thermal Protection Systems

Woven, ablative thermal protection system (TPS) materials provide a robust option for aggressive (re)entries and thus have been baselined for the upcoming Mars Sample Return (MSR) mission’s Earth Entry System (EES). The reliability requirements for MSR-EES necessitate understanding of material property variability, which could be significant given the complex structure and anisotropic nature of properties in TPS weaves, as well as the response to potential impact with micrometeoroids or orbital debris during the EES re-entry. The TPS Certification by Analysis effort within the Entry Systems Modeling project seeks to provide computational models and analyses that support the certification against such material-based risks. For the present talk, focus will be given to the characterization of baseline woven TPS material properties and mechanical failure limits, which entails (1) use of computational techniques (e.g., machine learning) to interpret computed tomography images of the weave to generate representative structural models and (2) application of multiscale material modeling approaches to characterize thermomechanical and failure properties.

Justin B. Haskins↗
NASA NTRS1993

Nonlinear probabilistic finite element models of laminated composite shells

A probabilistic finite element analysis procedure for laminated composite shells has been developed. A total Lagrangian finite element formulation, employing a degenerated 3-D laminated composite shell with the full Green-Lagrange strains and first-order shear deformable kinematics, forms the modeling foundation. The first-order second-moment technique for probabilistic finite element analysis of random fields is employed and results are presented in the form of mean and variance of the structural response. The effects of material nonlinearity are included through the use of a rate-independent anisotropic plasticity formulation with the macroscopic point of view. Both ply-level and micromechanics-level random variables can be selected, the latter by means of the Aboudi micromechanics model. A number of sample problems are solved to verify the accuracy of the procedures developed and to quantify the variability of certain material type/structure combinations. Experimental data is compared in many cases, and the Monte Carlo simulation method is used to check the probabilistic results. In general, the procedure is quite effective in modeling the mean and variance response of the linear and nonlinear behavior of laminated composite shells.

Engelstad, S. P.↗
NASA NTRS2017

Anisotropic Copoly(Imide Oxetane) Coatings and Articles of Manufacture, Copoly(Imide Oxetane)s Containing Pendant Fluorocarbon Moieties, Oligomers and Processes Therefor

Copoly(imide oxetane) materials are disclosed that can exhibit a low surface energy while possessing the mechanical, thermal, chemical and optical properties associated with polyimides. The copoly(imide oxetane)s are prepared using a minor amount of fluorinated oxetane-derived oligomer with sufficient fluorine-containing segments of the copoly(imide oxetane)s that migrate to the exterior surface of the polymeric material to yield low surface energies. Thus the coatings and articles of manufacture made with the copoly(imide oxetane)s of this invention are characterized as having an anisotropic fluorine composition. The low surface energies can be achieved with very low content of fluorinated oxetane-derived oligomer. The copolymers of this invention can enhance the viability of polyimides for many applications and may be acceptable where homopolyimide materials have been unacceptable.

Wohl, Christopher J.↗
NASA NTRS1974

Elastic moduli of precompressed pyrophyllite used in ultrahigh pressure research

The propagation of ultrasonic pulses in pyrophyllite specimens was studied to determine the effect of specimen precompression on the measured elastic moduli. Measurements were made at room pressure and, for the precompressed specimens, to pressures of 3 kbar. Pyrophyllite was found to be elastically anisotropic, apparently the result of the fabric present in our material. The room pressure adiabatic bulk modulus as measured on specimens made of isostatically compacted powered pyrophyllite was determined to be 96.1 kbar. The wave speeds of ultrasonic pulses in pyrophyllite were found to decrease with increasing specimen precompression. A limiting value of precompression was found, above which no further decrease in wave speed was observed. For the shear wave speeds this occurs at 10 kbar while for the longitudinal wave at 25 kbar. In the limit, the shear waves propagate 20% slower than in the unprecompressed samples; for the longitudinal wave the difference is 30%.

Sachse, W.↗
NASA NTRS1990

Analyses of composite fuselage structure under various loading conditions

With the characteristics of high strength/weight and stiffness/weight ratios in advanced composite materials, composite plate structures have been successfully applied to secondary load-carrying structural components in the aerospace industry for the past two decades. Recently, filament wound composite shells are being considered for design of primary fuselage structures. To implement the design the structural response under various loading conditions needs to be predicted accurately. Therefore, it is essential to establish a rigorous analytical solution in the area of composite laminated shells. A closed form solution is presented that predicts the response of a composite shell subjected to internal pressure, axial tension, bending, and torsion. The material of the shell is assumed to be general cylindrically anisotropic. Based on the theory of cylindrical anisotropic elasticity coupled partial differential governing equations are developed using Lehknitskii's stress function approach. The general expressions for the stresses and displacements in the composite cylinders under these loading conditions is discussed. Three examples (45) off-axis unidirectional, (45/45) unsymmetric, and (45/45)(sub s) symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratios, coupling, and stacking sequence.

Yuan, Fuh-Gwo↗
NASA NTRS1992

Exact solutions for laminated composite cylindrical shells in cylindrical bending

Analytic elasticity solutions for laminated composite cylindrical shells under cylindrical bending are presented. The material of the shell is assumed to be general cylindrically anisotropic. Based on the theory of cylindrical anisotropic elasticity, coupled governing partial differential equations are developed. The general expressions for the stresses and displacements in the laminated composite cylinders are discussed. The closed form solutions based on Classical Shell Theory (CST) and Donnell's (1933) theory are also derived for comparison purposes. Three examples illustrate the effect of radius-to-thickness ratio, coupling and stacking sequence. The results show that, in general, CST yields poor stress and displacement distributions for thick-section composite shells, but converges to the exact elasticity solution as the radius-to-thickness ratio increases. It is also shown that Donnell's theory significantly underestimates the stress and displacement response.

Yuan, F. G.↗
NASA NTRS1996

Computational Methods for Frictional Contact With Applications to the Space Shuttle Orbiter Nose-Gear Tire

A computational procedure is presented for the solution of frictional contact problems for aircraft tires. A Space Shuttle nose-gear tire is modeled using a two-dimensional laminated anisotropic shell theory which includes the effects of variations in material and geometric parameters, transverse-shear deformation, and geometric nonlinearities. Contact conditions are incorporated into the formulation by using a perturbed Lagrangian approach with the fundamental unknowns consisting of the stress resultants, the generalized displacements, and the Lagrange multipliers associated with both contact and friction conditions. The contact-friction algorithm is based on a modified Coulomb friction law. A modified two-field, mixed-variational principle is used to obtain elemental arrays. This modification consists of augmenting the functional of that principle by two terms: the Lagrange multiplier vector associated with normal and tangential node contact-load intensities and a regularization term that is quadratic in the Lagrange multiplier vector. These capabilities and computational features are incorporated into an in-house computer code. Experimental measurements were taken to define the response of the Space Shuttle nose-gear tire to inflation-pressure loads and to inflation-pressure loads combined with normal static loads against a rigid flat plate. These experimental results describe the meridional growth of the tire cross section caused by inflation loading, the static load-deflection characteristics of the tire, the geometry of the tire footprint under static loading conditions, and the normal and tangential load-intensity distributions in the tire footprint for the various static vertical loading conditions. Numerical results were obtained for the Space Shuttle nose-gear tire subjected to inflation pressure loads and combined inflation pressure and contact loads against a rigid flat plate. The experimental measurements and the numerical results are compared.

Tanner, John A.↗
NASA NTRS1996

Computational methods for frictional contact with applications to the Space Shuttle orbiter nose-gear tire: Comparisons of experimental measurements and analytical predictions

A computational procedure is presented for the solution of frictional contact problems for aircraft tires. A Space Shuttle nose-gear tire is modeled using a two-dimensional laminated anisotropic shell theory which includes the effects of variations in material and geometric parameters, transverse-shear deformation, and geometric nonlinearities. Contact conditions are incorporated into the formulation by using a perturbed Lagrangian approach with the fundamental unknowns consisting of the stress resultants, the generalized displacements, and the Lagrange multipliers associated with both contact and friction conditions. The contact-friction algorithm is based on a modified Coulomb friction law. A modified two-field, mixed-variational principle is used to obtain elemental arrays. This modification consists of augmenting the functional of that principle by two terms: the Lagrange multiplier vector associated with normal and tangential node contact-load intensities and a regularization term that is quadratic in the Lagrange multiplier vector. These capabilities and computational features are incorporated into an in-house computer code. Experimental measurements were taken to define the response of the Space Shuttle nose-gear tire to inflation-pressure loads and to inflation-pressure loads combined with normal static loads against a rigid flat plate. These experimental results describe the meridional growth of the tire cross section caused by inflation loading, the static load-deflection characteristics of the tire, the geometry of the tire footprint under static loading conditions, and the normal and tangential load-intensity distributions in the tire footprint for the various static vertical-loading conditions. Numerical results were obtained for the Space Shuttle nose-gear tire subjected to inflation pressure loads and combined inflation pressure and contact loads against a rigid flat plate. The experimental measurements and the numerical results are compared.

Tanner, John A.↗
NASA NTRS1973

A critical survey of wave propagation and impact in composite materials

A review of the field of stress waves in composite materials is presented covering the period up to December 1972. The major properties of waves in composites are discussed and a summary is made of the major experimental results in this field. Various theoretical models for analysis of wave propagation in laminated, fiber and particle reinforced composites are surveyed. The anisotropic, dispersive and dissipative properties of stress pulses and shock waves in such materials are reviewed. A review of the behavior of composites under impact loading is presented along with the application of wave propagation concepts to the determination of impact stresses in composite plates.

Moon, F. C.↗
NASA NTRS1988

Structural analyses of engine wall cooling concepts and materials

The severe thermal environments under which hypersonic aircraft such as the National Aerospace Plane (NASP) will operate require cooling of the engine walls, especially in the combustor. A preliminary assessment is made of some candidate materials based on structural analyses for a number of convective cooling configurations. Three materials were studied: graphite/copper and tungsten/copper composite alloys with 50 percent fiber volume fractions and a wrought cobalt-base superalloy, Haynes 188. Anisotropic mechanical and thermal properties for the composites were obtained from a computer code, ICAN, which determines the composite material properties from the individual properties of the fiber and matrix materials. The structural analyses were performed by using the MARC nonlinear finite element code. Heat transfer analyses were conducted to calculate the metal temperature distributions.

Kaufman, Albert↗
NASA NTRS1972

On fracture phenomena in advanced fiber composite materials.

The extension of linear elastic fracture mechanics (LEFM) from metallic alloys to advanced fiber composite laminates is considered. LEFM is shown to be valid for both isotropic and anisotropic homogeneous continua; the applicability of LEFM to advanced fiber composites is thus dependent on the validity of a homogeneous model of such materials. An experimental program to determine the validity of such a model for graphite/epoxy laminates is reviewed. Such laminates are found to have an apparent fracture toughness, from which it is inferred that a homogeneous material model is valid for the particular specimen geometry and composite laminates considered. Strain energy release rates are calculated from the experimentally determined fracture toughness of the various laminates. These strain energy release rates are found to lie in one of two groups, depending upon whether crack extension required fiber failure or matrix failure. The latter case is further investigated. It is concluded that matrix failure is governed by the tensile stress normal to the crack path.

Konish, H. J., Jr.↗
NASA NTRS1977

Development of a plasma sprayed ceramic gas path seal for high pressure turbine applications

The plasma sprayed graded layered yittria stabilized zirconia (ZrO2)/metal(CoCrAlY) seal system for gas turbine blade tip applications up to 1589 K (2400 F) seal temperatures was studied. Abradability, erosion, and thermal fatigue characteristics of the graded layered system were evaluated by rig tests. Satisfactory abradability and erosion resistance was demonstrated. Encouraging thermal fatigue tolerance was shown. Initial properties for the plasma sprayed materials in the graded, layered seal system was obtained, and thermal stress analyses were performed. Sprayed residual stresses were determined. Thermal stability of the sprayed layer materials was evaluated at estimated maximum operating temperatures in each layer. Anisotropic behavior in the layer thickness direction was demonstrated by all layers. Residual stresses and thermal stability effects were not included in the analyses. Analytical results correlated reasonably well with results of the thermal fatigue tests. Analytical application of the seal system to a typical gas turbine engine application predicted performance similar to rig specimen thermal fatigue performance. A model for predicting crack propagation in the sprayed ZrO2/CoCrAlY seal system was proposed, and recommendations for improving thermal fatigue resistance were made. Seal system layer thicknesses were analytically optimized to minimize thermal stresses in the abradability specimen during thermal fatigue testing. Rig tests on the optimized seal configuration demonstrated some improvement in thermal fatigue characteristics.

Shiembob, L. T.↗