SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Shutoff and time delay valve, which incorporates a metering spool that moves at constant velocity under pneumatic pressure and spring compression, increases fluid-flow area at a uniform rate. Diaphragm areas, control cavity volume, and bleed-orifice size may be varied to give any desired combination of time delay and spool travel time.
Remotely controlled sampling device obtains timed sample of flowing cryogenic liquid propellants in remote or hazardous testing conditions. The device consists of a calibrated container, a dewar, a solenoid valve, a pressure gage, and a manual bleed valve.
Wind tunnel study of boundary-layer-control throat bleed slot variations on internal performance of side inlet at Mach numbers 2.0 and 2.3
Efficiency evaluation of two-stage turbine with low ratio of blade to jet speed suitable for bleed-type high energy liquid rocket applications
Controls and control experimental program for nuclear rocket engine employing hot bleed cycle
IBM 7094 digital computer program for simulating steady state operation of NERVA hot-bleed engines over full chamber pressure and temperature operational ranges
Approximate average midspan metal temperatures and coolant flow requirements for turbine airfoils cooled by compressor exit bleed air
Wind tunnel tests of mixed-compression axisymmetric inlet system to determine bleed mass flow ratio, pressure recovery and pressure distortion
Relief valve to permit slow and fast bleeding rates at difference pressure levels
Stable operating range of supersonic mixed compression inlet increase by air flow removal via throat bleed system
G suit application to clinical therapeutics, noting intraabdominal bleeding control
Rake mounting design reduces aerodynamic-surface discontinuities to a minimum when installed in boundary layer bleed area. Mounting base is not required and, because of simplicity, rake can be manufactured at low cost.
The inlet was designed to have the minimum internal contraction consistent with high total-pressure recovery and low cowl drag. Without a bypass system, the peak pressure recoveries increased from 0.890 to 0.936 when the supercritical bleed mass flow ratio was varied from 0.035 to 0.060. With an operating bypass system and installed centerbody vortex generators, a slight increase in peak pressure recovery was obtained. The values of steady-state distortion and dynamic distortion were below 0.10 and 0.02, respectively, near critical operation. Simulation of a turbofan engine with concentric pipes showed no effect on compressor face flow profiles with varying bypass flow ratio.
Pollutant emissions from jet aircraft and combustion research aimed at reducing these emissions are defined. The problem of smoke formation and results achieved in smoke reduction from commercial combustors are discussed. Expermental results of parametric tests performed on both conventional and experimental combustors over a range of combustor-inlet conditions are presented. Combustor design techniques for reducing pollutant emissions are discussed. Improved fuel atomization resulting from the use of air-assist fuel nozzles has brought about significant reductions in hydrocarbon and carbon monoxide emissions at idle. Diffuser tests have shown that the combustor-inlet airflow profile can be controlled through the use of diffuser-wall bleed and that it may thus be possible to reduce emissions by controlling combustor airflow distribution. Emissions of nitric oxide from a shortlength annular swirl-can combustor were significantly lower than those from a conventional combustor operating at similar conditions.
The test results describe isolated intake performance between Mach 0.95 and the cruise Mach number of 2.65 at angles of incidence from +5 to -5 deg. Maximum total pressure recoveries of over 94 percent with 10 percent distortion were recorded at the compressor face in the Mach range from 2.65 to 2.4. Typical cruise operating recovery was 91 percent with 13 percent distortion, 7 percent bleed, 5 percent corrected flow stability margin, and 2.2 deg angle-of-incidence tolerance without need for control action. In the started range below Mach 2.4, recoveries were 2 percent to 4 percent lower than the recoveries above Mach 2.4, and the distortion increased to approximately 20 percent. At Mach 0.95 the maximum measured capture flow was 99.4 percent of the theoretical choked value. The recovery was 97.1 percent with less than 10 percent distortion.
Details of the test program, an outline of the test procedure, and results of the investigation in tabular form are presented. The base drag reduction potential was determined at cruise conditions (M = .40) of a modified base region, with and without base bleed flow. Transonic effects and cruise control effectiveness of the new base region were also obtained. The tests were performed at Mach numbers from 0.40 to 1.10, at angles of attack from -4 to +20 degrees and at angles of sideslip from -6 to +6 degrees, all at a Reynolds number of 6.56 million per meter (2.0 million per foot).
Results of recent tests of a large-scale axisymmetric mixed-compression inlet system designed for Mach number 2.65 indicate that the performance of the supersonic diffuser and required boundary-layer bleed system can be accurately estimated with relatively new analytic methods. Thus, many wind tunnel testing hours can be saved by avoiding much of the usual ?cut and try' wind tunnel development.
The purpose of this paper is to define the problem of pollutant emissions from jet aircraft and to review NASA-Lewis combustion research aimed at reducing these emissions. The problem of smoke formation and results achieved in smoke reduction from commercial combustors are discussed. Experimental results of parametric tests performed on both conventional and experimental combustors over a range of combustor-inlet conditions are presented. Combustor design techniques for reducing pollutant emissions are discussed. Improved fuel atomization resulting from the use of air-assist fuel nozzles has brought about significant reductions in hydrocarbon and carbon monoxide emissions at idle. Diffuser tests have shown that the combustor-inlet airflow profile can be controlled through the use of diffuser-wall bleed and that it may thus be possible to reduce emissions by controlling combustor airflow distribution. Emissions of nitric oxide from a shortlength annular swirl-can combustor were significantly lower than those from a conventional combustor operating at similar conditions.