Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Low loss Sr{sub 1-x}Ca{sub x}La{sub 4}Ti{sub 5}O{sub 17} microwave dielectric ceramics

Highlights: {yields} New single phase highly dense (95%) microwave dielectric Sr{sub 1-x}Ca{sub x}La{sub 4}Ti{sub 5}O{sub 17} (0 {<=} x {<=} 1) ceramics were designed and processed. {yields} Theoretical density and molar volume decreased due to the substitution of small Ca{sup 2+} for large Sr{sup 2+}. {yields} As required for microwave dielectric applications, optimum properties (i.e. {epsilon}{sub r} {approx} 53.7, Qf{sub o} {approx} 11,532 GHz and {tau}{sub f} {approx} -1.4 ppm/{sup o}C) were achieved for Sr{sub 0.4}Ca{sub 0.6}La{sub 4}Ti{sub 5}O{sub 17} (x = 0.6). -- Abstract: Microwave dielectric ceramics in the Sr{sub 1-x}Ca{sub x}La{sub 4}Ti{sub 5}O{sub 17} (0 {<=} x {<=} 1) composition series were prepared through a solid state mixed oxide route. All the compositions formed single phase ceramics within the detection limit of in-house X-ray diffraction when sintered in the temperature range 1450-1580 {sup o}C. Theoretical density and molar volume decreased due to the substitution of Ca{sup 2+} for Sr{sup 2+} which was associated with a decrease in the dielectric constant ({epsilon}{sub r}) and temperature coefficient of resonant frequency ({tau}{sub f}) but an increase in quality factor, Qf{sub o}. Optimum properties were achieved for Sr{sub 0.4}Ca{sub 0.6}La{sub 4}Ti{sub 5}O{sub 17} which exhibited, {epsilon}{sub r} {approx} 53.7, Qf{sub o} {approx} 11,532 GHz and {tau}{sub f} {approx} -1.4 ppm/{sup o}C.

36 MATERIALS SCIENCE↗

300°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems (Final Technical Report)

A silicon carbide (SiC) based electronic temperature sensor prototype has been demonstrated to operate at 300°C. We showed continuous operation of 1,000 hours with SiC operational amplifier and surface mounted discreet resistors and capacitors on a ceramic circuit board. This feasibility demonstration is a major milestone in the development of high temperature electronics in general and high temperature geothermal exploration and well management tools in particular. SiC technology offers technical advantages that are not found in competing technologies such as silicon-on-insulator (SOI) at high temperatures of 200°C to 300°C and beyond. The SiC integrated circuits and packaging methods can be used in new product introduction by GE Oil and Gas for high temperature down-hole tools. The existing SiC fabrication facility at GE is sufficient to support the quantities currently demanded by the marketplace, and there are other entities in the United States and other countries capable of ramping up SiC technology manufacturing. The ceramic circuit boards are different from traditional organic-based electronics circuit boards, but the fabrication process is compatible with existing ceramic substrate manufacturing. This project has brought high temperature electronics forward, and brings us closer to commercializing tools that will enable and reduce the cost of enhanced geothermal technology to benefit the public in terms of providing clean renewable energy at lower costs.

15 GEOTHERMAL ENERGY↗

A Python Package for Fuel Cycle and Waste Management Analysis - 19545

The future of nuclear power utilization in the United States may involve a transition from the once-through light water reactor fuel cycle to a so-called advanced fuel cycle. An advanced fuel cycle may offer improvements in natural resource utilization, reactor safety, and environmental impact. In addition, adoption of an advanced fuel cycle will result in changes in the amount, composition, and disposal of the nuclear wastes they produce. Characteristics intrinsic to the wastes themselves, such as mass and radioactivity at specific times, were used as waste management metrics in the Department of Energy 2014 Fuel Cycle Evaluation and Screening (FCES) study. Binning of these metrics informed fuel cycle according to relative potential benefit. However, waste properties alone cannot qualify management strategy. Therefore, comparing fuel cycles from the perspective of waste management can provide additional insights. To that end, an object-oriented Python package has been developed to perform fuel cycle waste management calculations. The package, named nwpy (short for Nuclear Waste analysis in Python), mimics the mass flow operations reported in the FCES study and interfaces with the ORIGEN-S code to assess metric data as reported in the FCES. In addition, this Python package determines the loading of waste streams into forms suitable for final disposal in a geological repository and uses such data for repository performance assessment. This work describes the Python package methodology, assumptions, and capabilities. As input data, the package requires information about the fuel cycle such as the mass of fuel discharged, the cooling time between reactor discharge and subsequent operations, and the separations process efficiencies and waste forms it produces. In addition, the isotopic composition of the reactor discharge stream, such as that available from the FCES database, is required. With that, it can perform prescribed mass flow and decay operations throughout the back end of the fuel cycle, the latter carried out by the ORIGEN-S code distributed with the SCALE6.2 software suite. The result is time-dependent data characterizing the waste on a per-package basis. Package loading for waste streams depends on the stream form (i.e. UNF vs. HLW, or glass HLW from aqueous reprocessing vs. ceramic HLW from electrochemical processing) and is based on literature review and engineering assumption. As an example of the application of the code, calculations for the areal footprint of direct-contact repositories for different fuel cycles is shown. Development is ongoing, and the package is expected to grow incorporating capabilities for waste management analyses such as waste transportation and radionuclide transport through the biosphere. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Experimental Study of the Aging and Self-Healing of Glass/Ceramic Sealant Used in SOFCs

High operating temperatures of solid oxide fuel cells (SOFCs) require that sealant must function at a high temperature between 600oC and 900oC and in the oxidizing and reducing environments of fuel and air. This paper describes tests to investigate the temporal evolution of the volume fraction of ceramic phases, the evolution of micro-damage, and the self-healing behavior of the glass ceramic sealant used in SOFCs. It was found that after the initial sintering process, further crystallization of the glass ceramic sealant does not stop, but slows down and reduces the residual glass content while boosting the ceramic crystalline content. Under the long-term operating environment, distinct fibrous and needle-like crystals in the amorphous phase disappeared, and smeared/diffused phase boundaries between the glass phase and ceramic phase were observed. Meanwhile, the micro-damage was induced by the cooling-down process from the operating temperature to the room temperature, which can potentially degrade the mechanical properties of the glass/ceramic sealant. The glass/ceramic sealant self-healed upon reheating to the SOFC operating temperature, which can restore the mechanical performance of the glass/ceramic sealant.

30 DIRECT ENERGY CONVERSION↗

Development of Additive Manufacturing for Ceramic Matrix Composite Vanes

This report discusses the development of additive manufacturing for polymer-derived ceramic materials to create novel cooled gas turbine airfoils made from ceramics. Gas turbine engines have extremely high temperatures in the hot section of the engine that exceed the melting point of nickel superalloy materials that the engine is made from. Advanced cooling technologies have been developed over decades for metallic parts. Ceramic materials have higher temperature capabilities than superalloys, but are difficult to shape in the complex designs used in modern turbines. Several thrusts were investigated during the project, including development of higher material strength resins, improvement of ultraviolet (UV) photopolymerization and post-processing techniques to increase survivability of ceramic parts, thermomechanical modeling of novel ceramic airfoil designs for higher cooling effectiveness, and experimental validation of the modeling and manufacturing in a turbine vane test facility at nondimensional conditions that are relevant to modern gas turbines. Some major findings of the work include a significant increase in ceramic survivability during pyrolysis (a high temperature process that converts the organic material to a ceramic) by adjusting the composition ratios of the resins, as well as a tolulene soak after printing to remove unreacted polymer material. Thermomechanical optimization of the internal cooling structure indicated that a high density pin fin array would enable an 80% increase in overall cooling effectiveness relative to a baseline geometry, which was later verified during experimental testing in a high speed linear cascade. Ceramic vanes were tested at Mach numbers of up to 0.9 which is relevant to modern gas turbines. High temperature capability of the ceramic vanes was not tested in this work.

36 MATERIALS SCIENCE↗

Novel High Temperature Carbide and Boride Ceramics for Direct Power Extraction Electrode Applications. Final report

The current project aims to develop new carbide and boride ceramic materials that incorporate different metal elements (e.g., (Hf 1-x Zr x )B 2 , also called ceramic solid solutions) and understand the fundamental composition-processing-structure-property relationships for such materials. Specifically, nano powders and related nano-composites for selected mixed metal carbide and boride materials are synthesized from nano-scale mixed precursors obtained from solution-based processing via heat treatment in inert atmosphere. The obtained fine powders were then consolidated into dense ceramics via a novel flash sintering process. The mechanical properties and thermal oxidation resistance for the obtained materials were evaluated for these materials. It was found that different synthesis routes produced powders with somewhat different characteristics in terms of composition and microstructure, which then led to different properties for the final ceramics. The synthesis and processing methods demonstrated in this study might be adopted for developing other similar high temperature ceramics, while the mixed metal or solid solution ceramic materials obtained from this study might be used as hot electrodes for direction power extraction and other energy-related applications.

20 FOSSIL-FUELED POWER PLANTS↗

Method and apparatus for fabricating ceramic and metal components via additive manufacturing with uniform layered radiation drying

A freeform extrusion fabrication process for producing three-dimensional ceramic, metal and functionally gradient composite objects, including the steps of filling a plurality of paste sources with a respective plurality of aqueous paste compositions, operationally connecting respective syringes containing respective aqueous paste compositions to a mixing chamber, moving a first aqueous paste composition from a first respective paste source into the mixing chamber, moving a second aqueous paste composition from a second respective paste source into the mixing chamber, mixing the first and second aqueous paste compositions to define a first admixture having a first admixture composition, extruding the first admixture onto a surface to define an extruded layer having a first admixture composition, surrounding the sides of the extruded layer with an oil bath, radiatively drying the extruded layer.

Leu, Ming C.↗

Fractographical characterization of hot pressed and pressureless sintered AlN-doped ZrB{sub 2}–SiC composites

In this paper, ZrB{sub 2}–SiC composites doped with 0–5 wt.% AlN were prepared by a low pressure hot pressing as well as a pressureless sintering methods at 1900 °C for 2 h. The influence of aluminum nitride addition on the sinterability and microstructure development of such ceramic composites was studied by a fractographical approach. The results revealed that only 1 wt.% AlN can aid the densification process of the hot pressed ceramic composite via the liquid phase sintering mechanism due to the formation of nano-scale metakaolinite spinel layers. In the pressureless sintering method, adding more AlN can increase the formation of gaseous products which raised the amount of porosities in the final microstructure. The formation of nano-graphite phase in the hot pressing process, the formation of Al{sub 2}OC in the pressureless sintering process, and the formation of BN in the both processes were disclosed by X-ray diffraction, SEM and TEM analyses. - Highlights: • The effect of AlN addition on densification of ZrB{sub 2}–SiC composites was studied. • AlN promotes the densification in hot pressed samples by liquid phase formation. • A fully dense composite was obtained by adding 1 wt.% AlN in hot pressing process. • In pressureless sintering, more AlN content intensifies the formation of porosities.

36 MATERIALS SCIENCE↗

Magnetorheological materials, method for making, and applications thereof

A magnetorheological material comprises a magnetic particle and a ceramic material, wherein the magnetorheological material is in a dried form and further wherein a portion of the ceramic material is in the form of a nanocrystalline coating over the entire exterior surface of the magnetic particle and another portion of the ceramic material is in the form of a free nanocrystal. A magnetorheological material comprises a magnetic particle having a ceramic material coating over an external surface thereof as a result of a coating process, and a free nanocrystal of the ceramic material in the form of a residual by-product of the coating process. A sol-gel process for making a magnetorheological product comprises providing a sol of a desired ceramic coating material; combining a desired quantity of carbonyl iron (CI) particles with the sol to coat the CI particles with the ceramic coating material; creating a resulting quantity of nanocrystalline ceramic material-coated CI particles and a quantity of free nanocrystals of the ceramic material; and, drying the resulting quantity of coated CI particles and free nanocrystals to a moisture content equal to or less than 2 wt %.

36 MATERIALS SCIENCE↗

A semi-empirical power-law model for the dip-coating of a substrate into a particle-containing, non-Newtonian, complex fluid system

The apparent viscosity of a particle suspension of ZrSi 2 particles, polyhydromethylsiloxane (PHMS) preceramic polymer and n-Octane solvent, used to process polymer-derived ceramic composite coatings, is shown by viscometric experiments to be shear-thinning. The suspension is dip-coated onto substrates and the measured entrained coating thickness, h 0 , is observed to be a power-law function of U, the substrate extraction speed, as h 0 = 0.5051U 0.5 . The experimentally observed semi-empirical model is directly compared to the results of a variety of theoretically derived Landau-Levich scaling laws and other models that have similar liquids and that include other effects. None of these cases predicts the scaling observed in these experiments. A correction factor is introduced to quantify the difference between the semi-empirical model with existing theoretical models. Possible explanations for the observed scaling behavior are presented.

36 MATERIALS SCIENCE↗

Modeling MTS pyrolysis and SiC deposition kinetics using principal component analysis and neural networks

Accurate chemical kinetics modeling is crucial for improving the efficiency of chemical processing and synthesis of ceramic matrix composites. Detailed kinetic models are computationally expensive due to the large number of transported chemical species, while the simplified physics-based models, such as single-step global mechanisms, are efficient but often overlook key chemical intermediates and pathways. Recent deep learning approaches promise accurate and cost-effective models. Yet, they require additional closures for the transported nonlinear latent variables, complicating integration with existing solvers. In this work, we develop a hybrid linear—nonlinear reduced model for silicon carbide deposition from methyltrichlorosilane precursor by combining principal component analysis (PCA) and autoencoder (AE) neural network (NN) approaches. PCA is used to identify a smaller set of linear transport variables, enabling direct reuse of conventional transport solvers. NNs then reconstruct the full chemical state from these reduced variables. We demonstrate the method on a chemical vapor deposition reactor—comprising a gas-phase pyrolysis plug flow reactor and a heterogeneous surface reactor—over a wide range of temperatures, pressures, and residence times. Our PCA–AE model achieves high accuracy with only five transported scalars, achieving an eightfold cost reduction compared to detailed mechanisms, in both a priori (using data from the test set only) and a posteriori (coupled with a differential equation solver). In conclusion, notable errors arise primarily near training domain boundaries and for long residence times, indicating the need for domain shift indicators and better long-horizon predictions in future reduced chemistry model development.

autoencoder neural networks↗

Relaxor ferroelectric polymer exhibits ultrahigh electromechanical coupling at low electric field

Electromechanical (EM) coupling—the conversion of energy between electric and mechanical forms—in ferroelectrics has been used for a broad range of applications. Ferroelectric polymers have weak EM coupling that severely limits their usefulness for applications. Here, we introduced a small amount of fluorinated alkyne (FA) monomers (<2 mol %) in relaxor ferroelectric poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (PVDF-TrFE-CFE) terpolymer that markedly enhances the polarization change with strong EM coupling while suppressing other polarization changes that do not contribute to it. Under a low–dc bias field of 40 megavolts per meter, the relaxor tetrapolymer has an EM coupling factor (k 33 ) of 88% and a piezoelectric coefficient (d 33 ) >1000 picometers per volt. These values make this solution-processed polymer competitive with ceramic oxide piezoelectrics, with the potential for use in distinct applications.

36 MATERIALS SCIENCE↗

Decision Point 1 of Statement of Project Objectives (SOPO)Recovery Act: Development of ITM Oxygen Technology for Integration with Advanced Industrial Systems

Air Products is designing, building, and operating a ceramic membrane fabrication facility (the “CerFab”) to enable production of membrane modules to supply a conceptual 2000 ton per day (TPD) ITM Oxygen facility (the “ITM Oxygen Development Facility”). Air Products is executing this project under the American Recovery and Reinvestment Act (ARRA) with the objective to accelerate the adoption of ITM Oxygen technology to help meet the country’s goals for deploying clean power plants. The objective of this Topical Report is to address the requirements of Decision Point 1, which pertains to the Site Selection for the CerFab. Air Products with subcontractor Ceramatec, Inc., has determined a ceramic membrane module manufacturing process and the building and site requirements of the process consistent with the manufacturing objectives of the ITM Oxygen development program and this ARRA project. Based on cost estimates for new construction and refurbishments of existing sites, Air Products chose to consider only existing buildings rather than new construction. The Salt Lake City, Utah, region was selected as the preferred location for the CerFab to enable Ceramatec, Inc., to support the Phase V project and on-going Phase III development activities. Twenty available properties were screened in this region, from which one property emerged clearly as the most suitable property to house the CerFab. The site meets the requirements of the CerFab in terms of floor space, power and other utilities, and building structural features. The site also meets criteria for ease of obtaining the requirement environmental permits, and is within the project cost allocation for the building site. Moreover, the site formerly housed a manufacturing company that ceased operations in 2010 as a result of the economic recession of 2008-9; the region of the site has experienced more than a doubling of the unemployment rate since 2007. Restarting a manufacturing operation in the same facility will return employment to the area, consistent with the goals of the ARRA. Air Products recommends proceeding with procuring this preferred site and continuing to execute Task 30.1 to establish the CerFab at the site.

Armstrong, Phillip↗

Development of a Thermal Spray, Redox Stable, Ceramic Anode for Metal Supported SOFC

In this program, GE global research and GE fuel cells in Malta conducted thermal spray optimization experiments, initially focusing on a well-established ceramic anode formulation, lanthanum strontium titanate combined with gadolinium doped ceria. Powder engineering work was conducted both internally and with vendors to develop repeatable, stable, and flowable thermal spray feedstocks. Agglomerate sintering was conducted in the last phase of the project, building on earlier program work, and was used to increase run stability during the longer scaled up runs for the 410 cm 2 cells. Further powder engineering would be needed to fully design a powder ready for full scale manufacturing. During preliminary work on the LST-GDC electrodes, GE demonstrated 100 cm 2 stacks enduring multiple redox cycles with limited impact. Another key finding on the project was the identification of process conditions for two component ceramic anode thermal spray without the formation of phase impurities which were present in all early work on the program. GE global research and West Virginia University screened a large number of ceramic anode formulations, focused on identifying materials with ideal materials properties for use in SOFC anodes. In addition, synthetic scaling research was conducted to increase powder synthesis batch size several orders of magnitude during the course of project work. West Virginia University was able to show button cells using two component ceramic anodes which produced > 890 mW/cm 2 and even a single component SOFC button demonstrating > 1 W/cm 2 performance. These button cell tests show the great potential of these redox stable materials. Down-selected ceramic anode formulations were combined with the optimized thermal spray process methods to first demonstrate multiple groups of 100 cm 2 SOFC stacks able to achieve the power density goals for the project. GE research also quickly investigated the performance of a subset of these formulations on long term degradation tests and assessed their performance on simulated natural gas reformate. In the final phase of the program, scaling activities were employed to translate from the 100cm2 process up to 410 cm 2 . Two large format 10-cell stack tests were completed, and one of these stacks produced 0.987 kW which is one of the highest power demonstrations of ceramic anode, metal support, SOFC technology known to GE. These ceramic anode stacks had been produced with all other materials in the stack held constant, demonstrating the flexibility of the thermal spray process in scaling to very large electrode size.

30 DIRECT ENERGY CONVERSION↗

Intrinsic and extrinsic relaxation of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics: Effect of sintering

The effect of sintering process on the electrical properties of CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) ceramic dielectrics were investigated in this paper. It was found that grain size is affected by sintering and the nonlinear current-voltage (I-V) property will decrease with the increased sintering time. Also, the frequency and temperature dependences of dielectric permittivity and loss in the ranges of 10{sup -1}-10{sup 7} Hz and 130-270 K were studied. Two relaxation processes with activation energy of 0.51 eV and 0.10 eV, respectively, were found in the frequency dependence of tan {delta} and Cole-Cole planes, which can be interpreted in terms of insulating grain boundaries and semiconducting grains. It was suggested that grain boundary Maxwell-Wagner relaxation and ionization of oxygen vacancy V{sub O}{sup ++}, proposed as extrinsic and intrinsic relaxations, are responsible for the dielectric behaviors of CCTO ceramics.

36 MATERIALS SCIENCE↗

Screening and qualification methodology for SiC end plug processing methods

Deployment of SiC-ceramic-based fuel cladding for light water reactors requires a hermetic end plug–to–cladding joint that can withstand neutron irradiation during normal operation and maintain integrity during design-basis accidents. Reactor experiments have shown that some SiC composite tubes with SiC end plugs can retain hermeticity after irradiation. However, achieving consistent joint performance under irradiation remains a key challenge. Resolving this issue is essential to enable integral irradiation testing and to demonstrate fuel integrity under commercial-reactor irradiation conditions. This report aims to: (1) provide guidance for designing radiation-tolerant end plug joints for SiC cladding; (2) demonstrate experimental methods to detect processing defects that are unstable under neutron irradiation at light-water-reactor-relevant temperatures and doses; and (3) outline a step-by-step approach for designing and conducting reactor experiments to screen joining methods. The resulting data will be used to improve joint processing and to define critical defect types and sizes that must be detected and eliminated through non-destructive evaluation for quality assurance. Based on prior irradiation experiments at the High Flux Isotope Reactor, differential swelling among the cladding, bonding layer, and end plug was identified as an underlying mechanism for irradiation-induced joint degradation. Accordingly, this effect must be considered in the design of radiation-tolerant joining techniques. In this work, miniature SiC end plug joint specimens irradiated during the previous project were analyzed using X-ray computed tomography to characterize the joint microstructure. Digital volume correlation of the tomography data quantified radiation-induced microstructural changes and enabled evaluation of defect-related risks. Finally, ongoing neutron irradiation efforts using larger specimen volumes are presented. These efforts aim to statistically assess joint performance and to build a microstructure–performance (e.g., leak-tightness) dataset to inform processing improvements and quality control.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluation of THOR TM Mineralized Waste Forms (Granular and Monolith) for the DOE Advanced Remediation Technologies (ART) Phase 2 Project

The U.S. Department of Energy's (DOE) Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP's LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). In addition, the WTP LAW Vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as Cs-137, I-129, Tc-99, Cl, F, and SO 4 that volatilize at the vitrification temperature of 1150°C in the absence of a continuous cold cap. The current waste disposal path for the WTP-SW is to recycle it to the supplemental LAW treatment to avoid a large steady state accumulation in the pretreatment-vitrification loop. Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750°C) continuous method by which LAW and/or WTP-SW wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be as durable as LAW glass. Monolithing of the granular FBSR product, which is one of the objectives of this current study, is being investigated to prevent dispersion during transport or burial/storage but is not necessary for performance. FBSR testing of a Hanford LAW simulant and a WTP-SW simulant at the pilot scale was performed by THOR Treatment Technologies, LLC at Hazen Research Inc. in April/May 2008. The Hanford LAW simulant was the Rassat 68 tank blend and the target concentrations for the LAW was increased by a factor of 10 for Sb, As, Ag, Cd, and Tl; 100 for Ba and Re (Tc surrogate); 1,000 for I; and 254,902 for Cs based on discussions with the DOE field office and the environmental regulators and an evaluation of the Hanford Tank Waste Envelopes A, B, and C. It was determined through the evaluation of the actual tank waste metals concentrations that some metal levels were not sufficient to achieve reliable detection in the off-gas sampling. Therefore, the identified metals concentrations were increased in the Rassat simulant processed by TTT at HRI to ensure detection and enable calculation of system removal efficiencies, product retention efficiencies, and mass balance closure without regard to potential results of those determinations or impacts on product durability response such as Toxicity Characteristic Leach Procedure (TCLP). A WTP-SW simulant based on melter off-gas analyses from Vitreous State Laboratory (VSL) was also tested at HRI in the 15-inch diameter Engineering Scale Test Demonstration (ESTD) dual reformer at HRI in 2008. The target concentrations for the Resource Conservation and Recovery Act (RCRA) metals were increased by 16X for Se, 29X for Tl, 42X for Ba, 48X for Sb, by 100X for Pb and Ni, 1000X for Ag, and 1297X for Cd to ensure detection by the analytic laboratory used for the demonstration and, as with the LAW simulant, without regard to potential impacts on product durability response such as TCLP. Details of the ESTD testing that was performed in April and May of 2008 are shown in Table 1 as the Operational Summary. The first eight tests were performed on LAW using a Denitration and Mineralization Reformer (DMR) temperature of 725°C and different ratios of clay:simulant of 675 g or 640 g of OptiKast clay per liter of simulant. The last four tests were performed on WTP-SW (originally referred to as LAW-Recycle) using a DMR temperature in the range of 680°C to 700°C with a mixture of 45/55 Sagger/OptiKast clay with 307 g clay/L simulant. The coal feed rates used in the FBSR processing are also shown as noted at the bottom of Table 1. It should be noted that the carbon feed rates are averaged over those periods.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗