Search NASA⌕ Search

SEARCH · Search NASA

Results for “closed loop”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Development and validation of a mathematical model of heart rate response to fluid perturbation

Physiological closed-loop controlled (PCLC) medical devices monitor and automatically adjust the patient’s condition by using physiological variables as feedback, ideally with minimal human intervention to achieve the target levels set by a clinician. PCLC devices present a challenge when it comes to evaluating their performance, where conducting large clinical trials can be expensive. Virtual physiological patients simulated by validated mathematical models can be utilized to obtain preclinical evidence of safety and assess the performance of the PCLC medical device during normal and worst-case conditions that are unlikely to happen in a limited clinical trial. A physiological variable that plays a major role during fluid resuscitation is heart rate (HR). For in silico assessment of PCLC medical devices regarding fluid perturbation, there is currently no mathematical model of HR validated in terms of its predictive capability performance. This paper develops and validates a mathematical model of HR response using data collected from sheep subjects undergoing hemorrhage and fluid infusion. The model proved to be accurate in estimating the HR response to fluid perturbation, where averaged between 21 calibration datasets, the fitting performance showed a normalized root mean square error (NRMSE) of 7.41 ± 2.8%. The model was also evaluated in terms of model predictive capability performance via a leave-one-out procedure (21 subjects) and an independent validation dataset (6 subjects). Two different virtual cohort generation tools were used in each validation analysis. The generated envelope of virtual subjects robustly met the defined acceptance criteria, in which 95% of the testing datasets presented simulated HR patterns that were within a deviation of 50% from the observed data. In addition, out of 16000 and 18522 simulated subjects for the leave one-out and independent datasets, the model was able to generate at least one virtual subject that was close to the real subject within an error margin of 9.56 ± 3.15% and 11.1 ± 1.22% NRMSE, respectively. In conclusion, the model can generate valid virtual HR physiological responses to fluid perturbation and be incorporated into future non-clinical simulated testing setups for assessing PCLC devices intended for fluid resuscitation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Flash Recycling of Graphite Anodes

The ever-increasing production of commercial lithium-ion batteries (LIBs) will result in a staggering accumulation of waste when they reach their end of life. A closed-loop solution, with effective recycling of spent LIBs, will lessen both the environmental impacts and economic cost of their use. Presently, <5% of spent LIBs are recycled and the regeneration of graphite anodes has, unfortunately, been mostly overlooked despite the considerable cost of battery-grade graphite. Here, in this work, an ultrafast flash recycling method to regenerate the graphite anode is developed and valuable battery metal resources are recovered. Selective Joule heating is applied for only seconds to efficiently decompose the resistive impurities. The generated inorganic salts, including lithium, cobalt, nickel, and manganese, can be easily recollected from the flashed anode waste using diluted acid, specifically 0.1 M HCl. The flash-recycled anode preserves the graphite structure and is coated with a solid-electrolyte-interphase-derived carbon shell, contributing to high initial specific capacity, superior rate performance, and cycling stability, when compared to anode materials recycled using a high-temperature-calcination method. Life-cycle-analysis relative to current graphite production and recycling methods indicate that flash recycling can significantly reduce the total energy consumption and greenhouse gas emission while turning anode recycling into an economically advantageous process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deep Learning for Rapid Analysis of Spectroscopic Ellipsometry Data

High‐throughput experimental approaches to rapidly develop new materials require high‐throughput data analysis methods to match. Spectroscopic ellipsometry is a powerful method of optical properties characterization, but for unknown materials and/or layer structures the data analysis using traditional methods of nonlinear regression is too slow for autonomous, closed‐loop, high‐throughput experimentation. Herein, three methods (termed spectral, piecewise, and pointwise) of spectroscopic ellipsometry data analysis based on deep learning are introduced and studied. After initial training, the incremental time for inferring optical properties can be a thousand times faster than traditional methods. Results for multilayer sample structures with optically isotropic materials are presented, appropriate for high‐throughput studies of thin films of phase‐change materials such as GeSbTe (GST) alloys. Results for studies on highly birefringent layered materials are also presented, exemplified by the transition metal dichalcogenide MoS 2 . How the materials under test and the experimental objectives may guide the choice of analysis methods are discussed. The utility of our approach is demonstrated by analyzing data measured on a composition spread of GeSbTe phase‐change alloys containing 177 distinct compositions, and identifying the composition with optimal phase‐change figure of merit in only 1.4 s of analysis time.

Li, Yifei↗
DOE OSTI2023

Comparing Parallel Plastic‐to‐X Pathways and Their Role in a Circular Economy for PET Bottles

Abstract The United States generates the most plastic waste of any country and is a top contributor to global plastic pollution. Multiple end‐of‐life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different lifetimes and utilities. Herein, they present a material flow model equipped with consequential life cycle assessment, cost analysis, and a plastic circularity indicator that considers product quality and lifetime. The model is used to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) bottle mechanical downcycling to lower‐quality resin, closed‐loop glycolysis to food‐grade PET, upcycling to glass fiber‐reinforced plastic, and conversion to non‐plastic products (electricity, oil) on a United States economy‐wide basis for the year 2020. A brute force algorithm suggests that a combination of 68% glycolysis, 11% mechanical recycling, 6% upcycling, 9% landfilling, and 5% incineration can minimize the cost and GHG emissions and maximize the circularity of the current PET economy. However, uncertainty around transportation distances, materials recovery facility efficiencies, and recycling yields can result in different “optimal” pathway mixes. This flexible framework enables informed decision‐making to move toward a cost‐ and environment‐conscious circular economy for plastic.

09 BIOMASS FUELS↗
DOE OSTI2021

The Value of Watching How Materials Grow: A Multimodal Case Study on Halide Perovskites

Material synthesis is one of the most important aspects in humankinds’ endeavor to discover and create new materials for energy applications. One strategy to tailor materials with desired functions in a rational way is by knowing how functions relate to structure, synthetic variables, arrangement of atoms and molecules, and how functions evolve during synthesis. In order to accelerate materials synthesis, discovery, and optimization by 10 times it is the right time now to integrate computational tools, synthesis, and characterization. One particular barrier to realizing this concept is the understanding of when and how phases form in real time during synthesis, which is challenging to asses by existing theoretical frameworks. In addition, transient or metastable phases with positive free energy above the lowest-free energy ground state can be revealed by such real time (in situ) measurements. Metastable materials are ubiquitous in condensed matter and can show superior properties compared to their equilibrium form. This work discusses the value of emerging multimodal in situ characterizations exemplified on hybrid halide perovskites. Finally, the ways in which the implementation of in situ measurements can advance the materials science synthesis field as well as their role to enable close-loop feedback control and autonomous synthesis are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sustainable Direct Recycling of Lithium-Ion Batteries via Solvent Recovery of Electrode Materials

Separation of electrode materials from their current collectors is an enabling step toward recovering critical materials from spent lithium-ion batteries. In this study, a highly efficient, cost-effective, and environmentally sustainable separation process was developed for that purpose. Ethylene glycol, a vital commodity chemical as an antifreeze and polymer precursor, is used to delaminate electrode materials at low temperatures in seconds without altering the crystalline structure and morphology of active electrode materials. The recovered current collectors were intact without any corrosion. The authors also found that the solvent could be continuously reused, leading to the development of a closed-loop ecosystem and lithium-ion battery circular economy. The ultrafast delamination was driven by the competitive inhibition of binding through the weakening of hydrogen bonding. The ethylene glycol-based separation is a sustainable electrode recovery process that paves the way for battery recycling.

25 ENERGY STORAGE↗
DOE OSTI2021

Engineered Sorghum Bagasse Enables a Sustainable Biorefinery with p-Hydroxybenzoic Acid-Based Deep Eutectic Solvent

Integrating multidisciplinary research in plant genetic engineering and renewable deep eutectic solvents (DESs) can facilitate a sustainable and economic biorefinery. In this work, we leveraged a plant genetic engineering approach to specifically incorporate C6C1 monomers into the lignin structure. By expressing the bacterial ubiC gene in sorghum, p-hydroxybenzoic acid (PB)-rich lignin was incorporated into the plant cell wall while this monomer was completely absent in the lignin of the wild-type (WT) biomass. A DES was synthesized with choline chloride (ChCl) and PB and applied to the pretreatment of the PB-rich mutant biomass for a sustainable biorefinery. The release of fermentable sugars was significantly enhanced (~190 % increase) compared to untreated biomass by the DES pretreatment. In particular, the glucose released from the pretreated mutant biomass was up to 12 % higher than that from the pretreated WT biomass. Lignin was effectively removed from the biomass with the preservation of more than half of the β-Ο-4 linkages without condensed aromatic structures. Hydrogenolysis of the fractionated lignin was conducted to demonstrate the potential of phenolic compound production. In addition, a simple hydrothermal treatment could selectively extract PB from the same engineered lignin, showing a possible circular biorefinery. These results suggest that the combination of PB-based DES and engineered PB-rich biomass is a promising strategy to achieve a sustainable closed-loop biorefinery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Endowing Polythioester Vitrimer with Intrinsic Crystallinity and Chemical Recyclability

Abstract Technologically important thermosets face a long‐standing end‐of‐life (EoL) problem of non‐reprocessability, a more sustainable solution of which has resolved to nascent vitrimers that can merge the robust material properties of thermosets and the reprocessability of thermoplastics. However, the lifecycle of vitrimers is still finite, as they often suffer from significant deterioration of mechanical performance following multiple reprocessing cycles, analogous to mechanical recycling, and they often show undesired creep under working conditions. To address these two key limitations, we have developed a cross‐linked semi‐crystalline polythioester with both dynamic covalent bonds and intrinsic crystallinity and chemical recyclability, affording a vitrimeric system that exhibits not only reprocessability and crystallinity‐restricted creep but also complete chemical recyclability to initial monomer by catalyzed depolymerization in solution or bulk. Therefore, reported herein is an “infinite” vitrimer system that is empowered with a facile closed‐loop EoL option once serial reprocessing deteriorates performance and the material can no longer meet the application requirements. Specifically, the polythioester vitrimer was constructed by copolymerization of a bicyclic thioester with a bis‐dithiolane, producing dynamically cross‐linked polythioesters with excellent property tunability, from amorphous to semi‐crystalline states and melting transition temperatures from 91 to 178 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Filtering adaptive output feedback control for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics

This article synthesizes a filtering adaptive output feedback controller for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics. The multivariable nonlinear systems under consideration have both matched and mismatched uncertainties, which satisfy the semiglobal Lipschitz condition. The unmodeled dynamics are bounded-input bounded-output stable. By adopting an estimation/cancellation strategy, a piecewise constant adaptive law drives the estimation error to zero at every time instant, which yields the adaptive parameters; a disturbance rejection control law is designed to compensate the nonlinear uncertainties within the bandwidth of low-pass filters. The matched uncertainties are cancelled directly by adopting their opposite in the control signal, while a dynamic inversion of the system is required to eliminate the effect of the mismatched uncertainties on the output. A feedforward control law is designed to track a given command. Since the virtual reference system defines the best performance that can be achieved by the closed-loop system, the uniform performance bounds are derived for the states and control signals via comparison. Both numerical and practical examples are provided to illustrate the effectiveness of the proposed filtering adaptive output feedback control architecture, comparisons with the model reference adaptive control demonstrates the superiority of the proposed control method.

filtering adaptive control, mismatched uncertainit↗
DOE OSTI2024

New Directions for Thermoelectrics: A Roadmap from High‐Throughput Materials Discovery to Advanced Device Manufacturing

Thermoelectric materials, which can convert waste heat into electricity or act as solid‐state Peltier coolers, are emerging as key technologies to address global energy shortages and environmental sustainability. However, discovering materials with high thermoelectric conversion efficiency is a complex and slow process. The emerging field of high‐throughput material discovery demonstrates its potential to accelerate the development of new thermoelectric materials combining high efficiency and low cost. The synergistic integration of high‐throughput material processing and characterization techniques with machine learning algorithms can form an efficient closed‐loop process to generate and analyze broad datasets to discover new thermoelectric materials with unprecedented performances. Meanwhile, the recent development of advanced manufacturing methods provides exciting opportunities to realize scalable, low‐cost, and energy‐efficient fabrication of thermoelectric devices. This review provides an overview of recent advances in discovering thermoelectric materials using high‐throughput methods, including processing, characterization, and screening. Advanced manufacturing methods of thermoelectric devices are also introduced to realize the broad impacts of thermoelectric materials in power generation and solid‐state cooling. In the end, this article also discusses the future research prospects and directions.

Song, Kaidong↗
DOE OSTI2024

Camelina circRNA landscape: Implications for gene regulation and fatty acid metabolism

Abstract Circular RNAs (circRNAs) are closed‐loop RNAs forming a covalent bond between their 3′ and 5′ ends, the back splice junction (BSJ), rendering them resistant to exonucleases and thus more stable compared to linear RNAs. Identification of circRNAs and distinction from their cognate linear RNA is only possible by sequencing the BSJ that is unique to the circRNA. CircRNAs are involved in the regulation of their cognate RNAs by increasing transcription rates, RNA stability, and alternative splicing. We have identified circRNAs from C. sativa that are associated with the regulation of germination, light response, and lipid metabolism. We sequenced light‐grown and etiolated seedlings after 5 or 7 days post‐germination and identified a total of 3447 circRNAs from 2763 genes. Most circRNAs originate from a single homeolog of the three subgenomes from allohexaploid camelina and correlate with higher ratios of alternative splicing of their cognate genes. A network analysis shows the interactions of select miRNA:circRNA:mRNAs for regulation of transcript stabilities where circRNA can act as a competing endogenous RNA. Several key lipid metabolism genes can generate circRNA, and we confirmed the presence of KASII circRNA as a true circRNA. CircRNA in camelina can be a novel target for breeding and engineering efforts.

Utley, Delecia [Department of Plant and Microbial ↗
DOE OSTI2023

Development of a wind turbine model and simulation platform using an acausal approach: Multiphysics modeling, validation, and control

This article presents the development of the Control-oriented, Reconfigurable, and Acausal Floating Turbine Simulator (CRAFTS). CRAFTS has a modular, hierarchical model architecture that enables rapid and accurate simulation of wind turbines. The architecture facilitates the incorporation of model variants, and its system reconfiguration features help simulate multiple design variants. CRAFTS also supports the integration of models developed on a causality-free platform (e.g., Modelica®) with existing causal models. This article focuses on the validation of a land-based wind turbine models against OpenFAST, an industry-standard platform, for several test cases. Closed-loop scenarios are also tested using the standard ROSCO controller and compared against OpenFAST. In addition, a nonlinear controller developed in our prior work is also evaluated. The test cases demonstrate the user-friendly and computationally efficient capabilities of CRAFTS to facilitate control co-design, assist in incorporating multiphysics models, be adaptable to design variants, and allow for rapid simulations to validate models and evaluate controllers.

17 WIND ENERGY↗
DOE OSTI2023

Integrated data-driven and experimental approaches to accelerate lead optimization targeting SARS-CoV- 2 main protease

Identification of potential therapeutic candidates can be expedited by integrating computational modeling with domain aware machine learning (ML) approaches followed by experimental validation. Generative deep learning models have been recently developed that can generate thousands of new candidates, but their physiochemical properties are typically not optimized. Using our deep learning models and a scaffold as a starting point, we generated tens of thousands of compounds for SARS-CoV-2 M pro that preserve the core scaffold. Here we utilized and implemented several computational tools such as structural alert and toxicity analysis, high throughput virtual screening, ML-based 3D quantitative structure–activity relationships, multi-parameter optimization, and graph neural networks on libraries of generated candidates to predict biological activity and binding affinity a priori. From these collective computational results, eight promising candidates were identified and tested experimentally using Native Mass Spectrometry (MS) and FRET-based functional assays. Two compounds, with quinazoline-2-thiol and acetylpiperidine core moiety showed IC 50 values in the low micromolar range: 2.95±0.0017 µM and 3.41±0.0015 µM, respectively. The molecular dynamics simulations further highlight that binding of these compounds results in allosteric modulations in the chain B and the interface domains of the M pro . The key fragments from these top hits can be used as input for closed loop lead optimization in the integrated pipeline.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

A Combined Thermochemical and Microbial Process for Recycling Polylactic Acid Polymer to Optically Pure L-Lactic Acid for Reuse

Polylactic acid polymer (PLA) produced from renewable resources can be recycled at the end of life to constituent monomer, optically pure lactic acid (LA), by a combination of chemical and biological processes. Efficient application of this closed loop of LA-PLA plastics-LA can minimize accumulation of plastics waste that pollute land and oceans. Temperature-dependent hydrolysis of PLA in water to LA follows apparent first order decay kinetics after a short lag. A modified Gompertz equation can explain the overall hydrolysis process. Alkali increased the rate of hydrolysis of PLA and reduced the length of lag period compared to water alone. The stoichiometry of base added to LA released was 1.0. The highest lactic acid yield was 0.95 g g -1 of PLA. D-LA in the syrup obtained after hydrolysis of PLA-plastics was removed using an engineered Escherichia coli to produce a L-LA syrup with an optical purity ≥ 99%. Here, these results show that thermochemical hydrolysis of PLA-based plastics to LA with optimum amount of base followed by bio-based purification to L-LA is an effective method of recycling PLA-plastics for reuse.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Simulation and Emulation of X-Ray Diffraction from Dynamic Compression Experiments

Many important aspects of the dynamic thermo-mechanical response of materials occur at the mesoscale, i.e. a physical scale of interactions smaller than what can be adequately described by homogenous behaviors, yet larger than the scale of the atomic lattice. Concurrent advancements in computational power, continuum theory, and experimental diagnostics are enabling unprecedented understanding of such interactions. However, we cannot develop a sufficient level of confidence in such mesoscale capability until the constitutive description of the underlying constituents is reliably representative of their actual physical behavior. Therefore, there is a strong need to combine experimental, modeling, and data-science techniques to validate models of the thermomechanical response of individual single crystals. One experimental diagnostic with high potential impact to shock physics and materials science is in-situ x-ray diffraction. This paper is primarily focused on simulation of x-ray diffraction in shock physics, but with an aim toward quantifying parametric uncertainty of simulation models. Here, we develop and demonstrate a data-science and model-driven approach to constrain the parameterization of continuum models of crystal lattice deformation associated with the shock response of crystalline materials. The framework is built around the connection between continuum hydrodynamic simulations of lattice deformation and a new Bragg diffraction simulation code, BarberShop. The dynamic deformation of a crystal lattice is modeled using the DiscoFlux model within an arbitrary Lagrangian-Eulerian hydrodynamic code, FLAG. These detailed continuum simulations of lattice deformation can be computationally slow, thus a statistical model is used to emulate the evolution of lattice deformation fields in time and across the considered model parameter space. Emulated lattice deformation fields can then be generated rapidly for any combination of physics model parameters. In turn, these fields can be fed into BarberShop to realize a rapid prediction of Bragg diffraction patterns associated with particular values of physics model parameters. The framework enables parameterization of the single crystal model to obtain Bragg diffraction patterns that most closely resemble a corresponding measurement. Furthermore, the framework naturally provides sensitivities of the lattice deformation to the physics parameters. We highlight the utility of this framework through the application to a synthetic closed-loop inverse problem leading to the parameterization of a single crystal material model. As a model problem, we consider the dynamic response of the energetic molecular crystal, cyclotrimethylenetrinitramine (or RDX), under dynamic compression induced by simulated flyer plate impact experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Travels, optimizations, and ordering

With all the necessary build pathing in place from the preceding steps, the final task is to organize the build pathing via directionality, ordering, and connectivity. Directionality controls closed-loop pathing by deciding whether construction occurs clockwise or counterclockwise. Ordering determines whether construction occurs outside-in or inside-out, by manipulating what path types will be printed first. Connectivity links all the pathing together, which is achieved through the insertion of travels. Connectivity has numerous approaches, but only the most common will be addressed in this chapter. In addition to these manipulations, other considerations, such as spiral pathing and unique cases for infill, will be discussed.

Borish, Michael↗
DOE OSTI2026

Demonstration and analysis of volumetric additive manufacturing via sub-orbital spaceflight testing

Computed Axial Lithography (CAL) represents a significant advancement in the emerging field of Volumetric Additive Manufacturing (VAM). CAL addresses key limitations of traditional photopolymer additive manufacturing technologies, by eliminating the need for layering and support structures. Unlike conventional methods, CAL prints components by illuminating all points within a desired geometry simultaneously, using tomographic reconstruction to form the object in a single step. This unique approach eliminates the relative motion between the object and the precursor material, enabling faster printing speeds and reducing the waste associated with support structures. However, CAL parts require post-processing steps before they can be utilized. CAL's core attributes make it particularly suited for In-Space Manufacturing (ISM), due to its fast fabrication times, wide breadth of materials it can use, and minimized footprint. CAL has been successfully demonstrated in microgravity during parabolic flight experiments. However to fully validate and understand CAL's behaviour in microgravity, all manufacturing and post-processing steps must be integrated. In June 2024, we conducted SpaceCAL Mission 3, testing this entire workflow on a suborbital flight aboard Virgin Galactic's SpaceShipTwo. During ~140 s of microgravity, the system autonomously manufactured and post-processed four parts using PEGDA700 resin. Post-flight analysis showed that 2/4 parts were recognisable, while others were distorted due to bubble formation from residual water droplets, off-axis optical aberrations, and non-uniform solvent rinsing. Despite these limitations, this study represents the first integrated CAL workflow in space, providing an initial experimental demonstration and analysis for closed-loop in-space manufacturing.

Waddell, Taylor [Department of Mechanical Engineer↗