Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Interactive Influence of Biofiber Composition and Elastomer on Physico-Mechanical Properties of PLA Green Composites

The objective of this work was to improve the impact and thermal properties of polylactic acid (PLA)-based biocomposite by appropriate application of cellulosic fiber and a bioelastomer. Biocomposites formulations with fiber contents of up to 20% in combination with a bioelastomer were extrusion-compounded in a twin-screw extruder followed by molding in an injection molding system. Fibers used in the formulations included three types of cellulosic fiber; namely, raw fiber from oat hull biomass (RF), hydrolysis byproduct (ATF) which was the solid fraction obtained from an acid-catalyzed hydrolysis of RF, and delignified fibers (AD30, AD65, AD100) which were the products of delignification of ATF. Formulated biocomposites were characterized for thermal (glass transition and melting temperatures, and enthalpy of melting) and physico-mechanical (tensile and bending strengths, stiffness, impact energy, and water absorption) properties. Among all types of biofibers, RF resulted in poor properties in the biocomposites due to the high hemicellulose content in the structure. On the other hand, the ratio of lignin to cellulose (in the absence of hemicellulose) in the modified fibers did not significantly affect the physico-mechanical and thermal properties of the biocomposites. The elastomer applied in the formulations improved the impact energy, thermal properties, and elongation at break of the composites. However, it adversely affected the strength and water resistance of biocomposites, especially in the presence of hemicellulose. The results indicated that, depending on the application, a wide range of PLA green composites with different physico-mechanical properties can be achieved.

09 BIOMASS FUELS↗
DOE OSTI2019

Manufacturing of a Metal Matrix Composite Coating on a Polymer Matrix Composite Through Cold Gas Dynamic Spray Technique

In this work, the manufacturing through cold gas dynamic spray (cold spray or CS) of metallic composite coatings of Al-Al{sub 2}O{sub 3} on organic composite substrates with thermoplastic PLA matrix and hemp fibers was studied. Alumina powders, with a mean diameter of 50 μm, were used blended with aluminum powders in three different weight concentration percentages (0, 15, 20, and 45%) as feedstock material in order to highlight and discuss the variations of the coating surface properties depending on the alumina percentage. The coatings were produced by using a low-pressure cold spray equipment. A detailed experimental campaign, including microstructural observations and confocal microscopy, was carried out to study the structure of the coatings. Moreover, the tribological behavior of the coatings was studied through both scratch test and pin-on-disk test. The experiments showed that a small addition of alumina improves the compactness of the coating and its resistance to scratch and wear behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Controlled optical properties via chemical composition tuning in molybdenum-incorporated β-Ga 2 O 3 nanocrystalline films

An approach is presented to design refractory-metal incorporated Ga2O3-based materials with controlled structural and optical properties. The molybdenum (Mo)-content in Ga2O3 was varied from 0 to 11 at% in the sputter-deposited Ga-Mo-O films. Molybdenum was found to significantly affect the structure and optical properties. While low Mo-content (≤4 at%) results in the formation of single-phase (β-Ga2O3), higher Mo-content results in amorphization. Chemically-induced band gap variability (Eg~1 eV) coupled with structure-modification indicates the electronic-structure changes in Ga-Mo-O. The linear relationship between chemical-composition and optical properties suggests that tailoring the optical-quality and performance of Ga-Mo-O films is possible by tuning the Mo-content.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2021

Reactive oxygen species alter chemical composition and adsorptive fractionation of soil organic matter

Reactive oxygen species (ROS), formed during redox fluctuations in iron-rich soils, have been known to stimulate lignin degradation, although not much is known about how they alter soil organic matter (SOM) composition and interaction with mineral surfaces. We conducted a laboratory experiment to see how ROS altered SOM composition and adsorptive fractionation onto Fe-mineral surfaces. We reacted water extracts of SOM with ·OH, produced by the Fenton reaction, and then conducted a sorption experiment of the extracts with goethite to analyze the amount and quality of SOM adsorbed. The Fenton reaction preferentially consumed low-O, mostly aromatic molecules, and new high-O molecules were detected post-Fenton, nearly half of which were carbohydrate-like. Although the amount of C adsorbed did not change after oxidation, the post-Fenton adsorbed molecules were more oxidized. Pre-Fenton adsorption was dominated by aromatic molecules (90%), but post-Fenton, the adsorbed molecules were 75% aromatic and 25% carbohydrate-like. We show that the ·OH radical oxidized SOM and shifted patterns of adsorption to a more oxidized pool. Because adsorption to minerals is thought to stabilize SOM, our results suggest that ROS may alter the availability and stabilization patterns of SOM.

Patel, Kaizad F.↗
DOE OSTI2022

Effects of composition and canister centerline cooling on microstructure, phase distribution, and chemical durability of dehalogenated iron phosphate waste forms

This paper discusses the effects of composition and canister centerline cooling (CCC) on the microstructures, phase distribution, and chemical durability of dehalogenated iron phosphate waste forms starting from chloride-based salt simulants including KCl (Simple-1), NdCl3 (Simple-2), SrCl2 (Simple-3), LaCl3 (Simple-4), LiCl (Simple-5), CsCl (Simple-6), as well as a complex simulant containing LiCl, KCl, NaCl, CsI, SrCl2, CeCl3, and NdCl3 called ERV2. The simulants represent salt constituents present in salt wastes from electrorefiners used for electrochemical reprocessing. These salts are reacted with ammonium dihydrogen phosphate (ADP) resulting in a NH4Cl (dechlorination) byproduct that is captured and phosphate product containing oxides of the salt cations. This product is further stabilized using Fe2O3 through vitrification at higher temperatures. The results presented herein describe the properties of CCC-treated materials following dechlorination and vitrification including phase identification and quantification, elemental distributions, and chemical durabilities. The chemical durability in the CCC-cooled samples are lower durability than quenched materials for the ERV2 samples. The phases formed upon CCC cooling are very complex compositionally and microstructurally.

iron phosphate glass, iron phosphate waste forms, ↗
DOE OSTI2019

Crystallographic and Compositional Analysis of impurity phase: U2MoSi2C in UMo Alloys

Minor impurity elements in metallic nuclear materials can critically influence the microstructural evolution and mechanical properties, making it crucial to understand the structure, composition and distribution of the impurity phases. Using Transmission Electron Microscopy, Atom Probe Tomography and ab-initio calculations we provide the atomic scale crystallographic structural and compositional analysis of a new impurity phase: U2MoSi2C in an important nuclear fuel U-10Mo alloy. We identify the new phase to have tetragonal symmetry with lattice parameters of a=6.67Å, c=4.33Å, and space group P4/mbm (No.127). Ab-initio calculations were performed to verify structural stability and to perform atom positions refinement.

Kovarik, Libor↗
DOE OSTI2018

Neutron scattering measurement of water content and chemical composition of alkali-glass powder reacted gel

Highlights: • Water absorption ability of alkali-glass powder reacted gel was largely reduced comparing other reported alkali-silica gels. • Both SAXS and SANS results showed similar internal structures of samples prepared with different H2O:D2O mixing ratios. • Neutron scattering method was developed to non-destructively determine gel water content and mass density of reacted gels. • Neutron scattering methods (based on scattering length density) on gel water content was validated with TGA measurement. - Abstract: Recent studies demonstrated that the added glass powder with high-alumina content could significantly reduce Alkali-Silica Reaction (ASR) damage in cement concrete. This paper aims to investigate the gel water content, chemical composition and expansion behavior of the alkali-glass powder reacted gel by using neutron scattering and other characterization techniques. Three types of samples were prepared with glass powder, sodium oxide and deuteroxide/hydrogen water with different molar ratios. The swelling potential of this alkali-glass powder reacted gel was much lower than that of the reported alkali-silica reacted gel. The gel water content and chemical compositions were characterized with small-angle neutron scattering (SANS) technique, supported by small-angle X-ray scattering (SAXS), prompt-gamma ray neutron activation analysis (PGAA) measurement. The SAXS test results showed the close scattering intensities, and thus similar internal microstructures among these samples. The elemental molar ratios of gels were obtained from the PGAA test results. Then the gel water molar ratio and mass density were determined by neutron scattering contrast calculation. The determined gel water content from neutron scattering analysis was validated with zero contrast analysis and TGA experimental measurement. Overall, this paper demonstrated the feasibility of using SANS technique to determine the water content of alkali-glass powder reacted gel.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Compositional dependence of optical band gap and refractive index in lead and bismuth borate glasses

Highlights: • Refractive indices increase with increasing PbO/Bi{sub 2}O{sub 3} content. • Optical band gap arises due to direct forbidden transition. • Optical band gaps decrease with increasing PbO/Bi{sub 2}O{sub 3} content. • New empirical relation between the optical band gap and the refractive index. - Abstract: We prepared a series of lead and bismuth borate glasses by varying PbO/Bi{sub 2}O{sub 3} content and studied refractive index and optical band gap as a function of glass composition. Refractive indices were measured very accurately using a Brewster’s angle set up while the optical band gaps were determined by analyzing the optical absorption edge using the Mott–Davis model. Using the Lorentz–Lorentz method and the effective medium theory, we calculated the refractive indices and then compared them with the measured values. Bismuth borate glasses show better agreement between the calculated values of the refractive index and experimental values. We used a differential method based on Mott–Davis model to obtain the type of transition and optical band gap (E{sub opt}) which in turn was compared with the value of E{sub opt} obtained using the extinction coefficient. Our analysis shows that in both lead and bismuth borate glasses, the optical band gap arises due to direct forbidden transition. With increasing PbO/Bi{sub 2}O{sub 3} content, the absorption edge shifts toward longer wavelengths and the optical band gap decreases. This behavior can be explained in terms of changes to the Pb−O/Bi−O chemical bonds with glass composition. We obtained a new empirical relation between the optical band gap and the refractive index which can be used to accurately determine the electronic oxide polarizability in lead and bismuth oxide glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Analysis of fission product distribution and composition in the TRISO layers of AGR-2 fuel

The Advanced Gas Reactor Fuel Qualification and Development Program's second irradiation experiment focuses on the performance of fuel particles produced in an industrial-scale coating system. Ongoing post-irradiation examination efforts include exploration of tristructural-isotropic (TRISO)-coated particle fuel in the as-irradiated state and subjected to elevated temperatures to simulate accident conditions (safety testing). Scanning electron microscopy (SEM) analysis with energy dispersive x-ray spectroscopy (EDS) was used to show the distribution of fission products within the TRISO layers. The SEM analysis showed a variation of fission product distribution within the TRISO layers based on irradiation temperature, burnup, individual particle fission product inventory retention, safety testing history and kernel composition. Finally, a key observation is that particles which likely experienced higher temperature showed a greater diversity and distribution of fission products and actinides in the IPyC and SiC layers, implying that temperature is a dominant variable influencing the transport of radionuclides in TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Multi 'omics comparison reveals metabolome biochemistry, not microbiome composition or gene expression, corresponds to elevated biogeochemical function in the hyporheic zone

Biogeochemical hotspots are pervasive at terrestrial-aquatic interfaces, particularly within groundwater-surface water mixing zones (hyporheic zones), and they are critical to understanding spatiotemporal variation in biogeochemical cycling. Here, we use multi ‘omic comparisons of hotspots to low-activity sediments to gain mechanistic insight into hyporheic zone organic matter processing. We hypothesized that microbiome structure and function, as described by metagenomics and metaproteomics, would distinguish hotspots from low-activity sediments through a shift towards carbohydrate-utilizing metabolic pathways and elucidate discrete mechanisms governing organic matter processing in each location. We also expected these differences to be reflected in the metabolome, whereby hotspot carbon (C) pools and metabolite transformations therein would be enriched in sugar-associated compounds. In contrast to expectations, we found pronounced phenotypic plasticity in the hyporheic zone microbiome that was denoted by similar microbiome structure, functional potential, and expression across sediments with dissimilar metabolic rates. Instead, diverse nitrogenous metabolites and biochemical transformations characterized hotspots. Metabolomes also corresponded more strongly to aerobic metabolism than bulk C content only (explaining 67% vs. 42% of variation), and bulk C did not improve statistical models based on metabolome composition alone. These results point to organic nitrogen as a significant regulatory factor influencing hyporheic zone organic matter processing. Based on our findings, we propose incorporating knowledge of metabolic pathways associated with different chemical fractions of C pools into ecosystem models will enhance prediction accuracy.

Graham, Emily B. (ORCID:0000000246237076)↗
DOE OSTI2020

Localized High Concentration Electrolytes for High Voltage Lithium-Metal Batteries: Correlation between the Electrolyte Composition and Its Reductive/Oxidative Stability

We demonstrate a first-principles screening methodology as an effective tool to explore electrolyte formulations for the new generation of high energy density rechargeable batteries. We study the liquid structure and electronic properties in dilute electrolytes, high concentration electrolytes (HCE), and localized high concentration electrolytes (LHCE), with focus on electrolyte formulations based on lithium bis(fluorosulfonyl)imide (LiFSI), dimethyl carbonate (DMC), and bis(2,2,2-trifluoroethyl) ether (BTFE) as a diluent. We describe the solvation complexes in the dilute electrolyte and explore structural changes triggered by the increase in lithium salt concentration for HCEs and the diluent effects in LHCEs. In HCE formulations, there is a 4-fold coordination environment of lithium-ions as in the dilute electrolyte, but the number of lithium-ion interactions with O atoms from FSI- anions dominates. In these solutions, the ability of the FSI- anions to interact with multiple lithium-ions allows complex 3D network formation and influences the reductive/oxidative behavior of the electrolyte. Interestingly, in LHCEs, the BTFE diluent molecules do not change the 3D solution structure when diluting the HCE formulation from 5.49 to 3.83 M. However, there is a composition threshold where the structural and electronic behavior may change. We show that diluting the HCE electrolyte with BTFE down to 1.77 M breaks the three-dimensional solution structure into an island-like solvation complex. We relate these structural changes to the electronic properties of the electrolytes finding a causal relationship between the reductive/oxidative behavior and the lithium-oxygen interaction mechanisms in the solvated complexes. The coordination with lithium-ions lowers the electrolyte LUMO and HOMO levels: the higher is the number of interactions with lithium-ions, the more likely the solvent molecule, FSI- anion, or diluent molecule is to be reduced and the less likely it is to become oxidized. The evolution of the solvated ion structure in HCE and LHCE suggests a close connection to a corresponding change in the lithium-ion transport mechanisms for these electrolytes.

anions, molecules, oxygen, solvents, electrolytes↗