Search NASA⌕ Search

SEARCH · Search NASA

Results for “dispersion analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Post-irradiation examination of commercial tantalum alloys following neutron irradiation

Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multi-technique characterization of spray coated and roll-to-roll coated gas diffusion fuel cell electrodes

Here this work reports the characterization of catalyst layer (CL) structure and composition for a set of gas-diffusion electrodes (GDEs) fabricated by different coating methods with the goal of developing a better understanding of CL processing-structure-property-performance relationships. The CL coating techniques used in this study were ultrasonic spray coating, and two roll-to-roll (R2R) methods - gravure and slot die. Scanning transmission electron microscopy (STEM) coupled with X-ray energy dispersive spectroscopy (EDS) analysis of GDE cross-sections provided bulk information, while scanning electron microscopy (SEM) with EDS and X-ray photoelectron spectroscopy (XPS) were used to investigate the near surface and surface composition of the CLs that will be in direct contact with the membrane once the membrane electrode assembly (MEA) is constructed. This study demonstrates that common quantification parameters, namely the F:Pt ratio extracted from cross-sectional STEM-EDS maps and top-down CL measurements with SEM and XPS, along with roughness parameters quantified from SEM micrographs are useful parameters in explaining and potentially predicting performance trends. Additionally, it highlights the importance of understanding key CL surface properties for advancing the manufacturability of high-performance components for polymer electrolyte membrane (PEM) technologies.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Investigating the weak charge of 48 Ca using a dispersive optical model

A new nonlocal dispersive-optical-model analysis has been carried out for neutrons and protons in 48 Ca that reproduces the weak-form-factor measurement of CREX. In addition to elastic-scattering angular distributions, total and reaction cross sections, single-particle energies, the neutron and proton numbers, and the charge distribution, the CREX-measured weak form factor has been fit to extract the neutron and proton self-energies both above and below the Fermi energy. The resulting single-particle propagators yield a weak form factor of F w = 0.125 ± 0.05 and a neutron skin of R skin = 0.152 ± 0.05 fm, in good agreement with CREX. The rearrangement of the neutron distribution to accommodate such a thin neutron skin results in the high-momentum content of the neutrons exceeding that of the protons, in contrast to what is expected from high-energy two-nucleon knockout measurements by the CLAS collaboration and ab initio asymmetric matter calculations. The present analysis also emphasizes the importance of neutron experimental data in constraining weak charge observables necessary for a precise description of neutron densities. Notably, the neutron reaction cross section and further parity-violating experiments weak form factor measurements are essential to generate a unique way to determine the 48 Ca neutron distribution in this framework.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Magnetically Induced Binary Ferrocene with Oxidized Iron

Ferrocene is perhaps the most popular and well-studied organometallic molecule, but our understanding of its structure and electronic properties has not changed for more than 70 years. In particular, all previous attempts of chemically oxidizing pure ferrocene by binding directly to the iron center have been unsuccessful, and no significant change in structure or magnetism has been reported. Here, using a metal organic framework host material, we were able to fundamentally change the electronic and magnetic structure of ferrocene to take on a never-before observed physically stretched/bent high-spin Fe(II) state, which readily accepts O 2 from air, chemically oxidizing the iron from Fe(II) to Fe(III). We also show that the binding of oxygen is reversible through temperature swing experiments. Our analysis is based on combining Mößbauer spectroscopy, extended X-ray absorption fine structure, in situ infrared, SQUID, thermal gravimetric analysis, and energy dispersive X-ray fluorescence spectroscopy measurements with ab initio modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Distinct and rich assemblages of giant viruses in Arctic and Antarctic lakes

Giant viruses (GVs) are key players in ecosystem functioning, biogeochemistry, and eukaryotic genome evolution. GV diversity and abundance in aquatic systems can exceed that of prokaryotes, but their diversity and ecology in lakes, especially polar ones, remain poorly understood. We conducted a comprehensive survey and meta-analysis of GV diversity across 20 lakes, spanning polar to temperate regions, combining our extensive lake metagenome database from the Canadian Arctic and subarctic with publicly available datasets. Leveraging a novel GV genome identification tool, we identified 3304 GV metagenome-assembled genomes, revealing lakes as untapped GV reservoirs. Phylogenomic analysis highlighted their dispersion across all Nucleocytoviricota orders. Strong GV population endemism emerged between lakes from similar regions and biomes (Antarctic and Arctic), but a polar/temperate barrier in lacustrine GV populations and differences in their gene content could be observed. Our study establishes a robust genomic reference for future investigations into lacustrine GV ecology in fast changing polar environments.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Precise Timing Based on Pulsar Observation for Grid Synchronization

While Global Positioning System signals are widely used as the synchronized timing Sources for wide-area measurement systems for power grid monitoring and control, they are vulnerable to failures and malicious attacks. To address this Problem, an alternative kind of timing sources, the millisecond pulsars, were proposed to serve the power grid as they are more precise and physically indestructible. Millisecond pulsars are a kind of neutron stars that emit radio pulse signals that have extremely stable periods of milliseconds. However, the observed pulse Signals from pulsars cannot be directly used for timing because of their low signal-to-noise ratio and the dispersion effects of interstellar medium. In this paper, the precise timing method based on pulsar observation data is proposed to interpret the pulsar observation data and therefrom to generate precise timing signal for the power grid synchronization. In our proposed method,. incoherent de-dispersion is used on the observation data to mitigate the effect of interstellar medium. dispersion. Then spectrum analysis and segment folding are used to precisely estimate the local pulsar period. Finally the standard pulse per second signal is generated from. the estimated pulsar period and its precision. is analyzed. Experiments with the observation data of the pulsar based timing signal can be more accurate compared to GPS timing signals.

Luo, Xiqian↗
DOE OSTI2025

Proton internal pressure from deeply virtual Compton scattering on collider kinematics

Abstract The unique experimental connection to the QCD energy–momentum tensor offered by generalised parton distributions has been strongly highlighted in the past few years with attempts to extract the pressure and shear forces distributions within the nucleon. If, in principle, this can be performed in a model independent way from experimental data, in practice, the current limited precision and kinematic coverage make such an extraction very challenging. Moreover, the limitation to a leading-order description in the strong coupling of the data has provided only an indirect and weakly sensitive access to gluon degrees of freedom, solely through their mixing to quarks via evolution. In this paper we address this issue by providing a next-to-leading order formalism allowing a reanalysis of global fits with genuine gluonic degrees of freedom. In addition, we provide an estimate of the reduction in uncertainty that could stem from the extended kinematic range relevant for the future Electron Ion Collider. Finally, we stress the connection between the analysis of the dispersion relation in terms of generalised parton distributions and the deconvolution problem.

Dutrieux, H. (ORCID:0000000183344885)↗
NASA NTRS1979

Radio science with Voyager at Jupiter - Initial Voyager 2 results and a Voyager 1 measure of the Io torus

About 22 hours after its closest approach to Jupiter, Voyager 2 passed behind the planet as viewed from the earth. Although the spacecraft was geometrically occulted for nearly two hours, the radio links between it and the earth were maintained almost continuously because of the refraction of the signals in Jupiter's south polar atmosphere. A figure shows the plane-of-the-sky geometry of this grazing occultation and preliminary data on the intensity of the spacecraft radio signals as received by the tracking station at Goldstone, California. The intensity data indicate a classic atmospheric occultation profile and the effects of turbulence and ionospheric focusing and defocusing. Analysis of the dispersive ionospheric refraction data yields preliminary profiles for the topside ionosphere at 66.7 deg S (entry in the evening) and 50.1 deg S (exit in the morning) that are reversed with respect to corresponding Voyager 1 profiles in terms of plasma concentration at a fixed altitude. Preliminary reduction of the preencounter occultation of Voyager 1 by the Io torus gives an average plasma density of about 1000 e/cu cm.

Eshleman, V. R.↗
NASA NTRS1982

Radiative transfer in realistic planetary atmospheres

Some 40 publications that appeared in scientific journals from 1973 to 1981 as well as 45 scientific reports issued during the grant period are listed by title. Topics cover the development of a matrix operator theory of radiative transfer which made possible the exact model calculations of the radiance as a function of height in planetary atmospheres; calculation of the Mie phase matrix for various types of particles as well as for radiance and polarization in planetary atmospheres; analysis of high dispersion spectroscopic observations of Venus; calculation of curves of growth for Venus; the development of a theory for calculating radiative transfer in spherical shell atmospheres; investigations of zonal winds on Venus; and examination of Rayleigh scattering.

Plass, G. N.↗
NASA NTRS1986

Turbulent motion in galactic H II regions

An investigation of radial velocities across the face of NGC 1499, NGC 7000, and S252 reveals that the fine-scale (turbulent) motions are well ordered from the limit of spatial resolution to the full size of the nebulae. As in higher spatial resolution studies of S142 and M17, analysis of the dispersion relation reveals that there is agreement with Kolmogorov theory (1941). However, study of the structure function reveals the same result as found by Roy and Joncas (1985), that the structure function increases with separation much more slowly than theoretically expected, calling into question the application of Kolmogorov theory. The Roy-Joncas result that the fine-scale motion seems to begin at about the sonic velocity are confirmed. It is shown that a condition exists of near equipartition of energies between fine-scale mass motion and thermal gas motion, which raises the question of a possible link.

Odell, C. R.↗
NASA NTRS1991

Microanalysis of extended-test xenon hollow cathodes

Four hollow cathode electron sources were analyzed via boroscopy, scanning electron microscopy, energy dispersive x ray analysis, and x ray diffraction analysis. These techniques were used to develop a preliminary understanding of the chemistry of the devices that arise from contamination due to inadequate feed-system integrity and improper insert activation. Two hollow cathodes were operated in an ion thruster simulator at an emission current of 23.0 A for approximately 500 hrs. The two tests differed in propellant-feed systems, discharge power supplies, and activation procedures. Tungsten deposition and barium tungstate formation on the internal cathode surfaces occurred during the first test, which were believed to result from oxygen contamination of the propellant feed-system. Consequently, the test facility was upgraded to reduce contamination, and the test was repeated. The second hollow cathode was found to have experienced significantly less tungsten deposition. A second pair of cathodes examined were the discharge and the neutralizer hollow cathodes used in a life-test of a 30-cm ring-cusp ion thruster at a 5.5 kW power level. The cathodes' test history was documented and the post-test microanalyses are described. The most significant change resulting from the life-test was substantial tungsten deposition on the internal cathode surfaces, as well as removal of material from the insert surface. In addition, barium tungstate and molybdate were found on insert surfaces. As a result of the cathode examinations, procedures and approaches were proposed for improved discharge ignition and cathode longevity.

Verhey, Timothy R.↗
NASA NTRS1992

Post-flight analyses of the crystals from the M0003-14 quartz crystal microbalance experiment

Quartz Crystal Microbalances constructed by QCM Research were flown on the leading and trailing edges of the Long Duration Exposure Facility (LDEF) as one of the sub-experiments of M0003. Response of the crystals coated with 150 A of IN2O3ZnS was recorded during the first 424 days of the mission. A second QCM with crystals coated with 150 A was also flown but not monitored. The flight data and temperature profiles will be presented. After the flight, the QCM's were disassembled and analyzed. The samples included the crystals from the leading and trailing edge samples of both types of coatings along with the reference crystals which were inside the QCM housing. Analyses were performed by scanning electron microscopy, energy dispersive x ray analysis, x ray photoelectron spectroscopy, ion microprobe mass analysis, and reflectance spectroscopy in the infrared and ultraviolet/visible region. The crystals were contaminated predominantly with silicone compounds. The contamination is higher on the leading edge than on the trailing edge, and higher on the exposed crystal than on the reference crystals. No significant differences in composition of the In2O3 crystals were noted. Differences in the reflectance and surface analysis of the Zns crystals will be discussed.

Stuckey, W. K.↗
NASA NTRS1998

Evidence of Microfossils in Carbonaceous Chondrites

Investigations have been carried out on freshly broken, internal surfaces of the Murchison, Efremovka and Orgueil carbonaceous chondrites using Scanning Electron Microscopes (SEM) in Russia and the Environmental Scanning Electron Microscope (ESEM) in the United States. These independent studies on different samples of the meteorites have resulted in the detection of numerous spherical and ellipsoidal bodies (some with spikes) similar to the forms of uncertain biogenicity that were designated "organized elements" by prior researchers. We have also encountered numerous complex biomorphic microstructures in these carbonaceous chondrites. Many of these complex bodies exhibit diverse characteristics reminiscent of microfossils of cyanobacteria such as we have investigated in ancient phosphorites and high carbon rocks (e.g. oil shales). Energy Dispersive Spectroscopy (EDS) analysis and 2D elemental maps shows enhanced carbon content in the bodies superimposed upon the elemental distributions characteristic of the chondritic matrix. The size, distribution, composition, and indications of cell walls, reproductive and life cycle developmental stages of these bodies are strongly suggestive of biology' These bodies appear to be mineralized and embedded within the meteorite matrix, and can not be attributed to recent surface contamination effects. Consequently, we have interpreted these in-situ microstructures to represent the lithified remains of prokaryotes and filamentous cyanobacteria. We also detected in Orgueil microstructures morphologically similar to fibrous kerite crystals. We present images of many biomorphic microstructures and possible microfossils found in the Murchison, Efremovka, and Orgueil chondrites and compare these forms with known microfossils from the Cambrian phosphate-rich rocks (phosphorites) of Khubsugul, Northern Mongolia.

Hoover, Richard B.↗
NASA NTRS2003

Defect Clustering and Nano-Phase Structure Characterization of Multi-Component Rare Earth Oxide Doped Zirconia-Yttria Thermal Barrier Coatings

Advanced oxide thermal barrier coatings have been developed by incorporating multi-component rare earth oxide dopants into zirconia-yttria to effectively promote the creation of the thermodynamically stable, immobile oxide defect clusters and/or nano-scale phases within the coating systems. The presence of these nano-sized defect clusters has found to significantly reduce the coating intrinsic thermal conductivity, improve sintering resistance, and maintain long-term high temperature stability. In this paper, the defect clusters and nano-structured phases, which were created by the addition of multi-component rare earth dopants to the plasma-sprayed and electron-beam physical vapor deposited thermal barrier coatings, were characterized by high-resolution transmission electron microscopy (TEM). The defect cluster size, distribution, crystallographic and compositional information were investigated using high-resolution TEM lattice imaging, selected area diffraction (SAD), electron energy-loss spectroscopy (EELS) and energy dispersive spectroscopy (EDS) analysis techniques. The results showed that substantial defect clusters were formed in the advanced multi-component rare earth oxide doped zirconia- yttria systems. The size of the oxide defect clusters and the cluster dopant segregation was typically ranging from 5 to 50 nm. These multi-component dopant induced defect clusters are an important factor for the coating long-term high temperature stability and excellent performance.

Zhu, Dongming↗
NASA NTRS2003

Nanocrystalline Chalcopyrite Materials (CuInS2 and CuInSe2) via Low-Temperature Pyrolysis of Molecular Single-Source Precursors

Nanometer sized particles of the chalcopyrite compounds CuInS2 and CuInSe2 were synthesized by thermal decomposition of molecular single-source precursors (PPh3)2CuIn(SEt)4 and (PPh3)2CuIn(SePh)4, respectively, in the non-coordinating solvent dioctyl phthalate at temperatures between 200 and 300 C. The nanoparticles range in size from 3 - 30 nm and are aggregated to form roughly spherical clusters of about 500 nm in diameter. X-ray diffraction of the nanoparticle powders shows greatly broadened lines indicative of very small particle sizes, which is confirmed by TEM. Peaks present in the XRD can be indexed to reference patterns for the respective chalcopyrite compounds. Optical spectroscopy and elemental analysis by energy dispersive spectroscopy support the identification of the nanoparticles as chalcopyrites.

Castro, Stephanie L.↗
NASA NTRS2003

Biogeochemistry of fluoride in a plant-solution system

Fluoride (F-) pollutants can harm plants and the animals feeding on them. However, it is largely unknown how complexing and chelating agents affect F bioavailability. Two studies were conducted that measured F- bioavailability and uptake by rice (Oryza sativa L.). In the first study, rice was grown in solution culture (pH 5.0) with 0, 2, or 4 mM F- as KF to compare the interaction of F- with humic acid (HA) and with a conventional chelating agent, N-hydroxyethylenthylenediaminetriacetic acid (HEDTA). In the second study, F was supplied at 0, 0.5, 1.0, and 2.0 mM KF with an additional 2 mM F- treatment containing solution Ca at 2x (2 mM Ca) the level used in the first study, to test the effect added Ca had on F- availability and uptake. Total biomass was greatest with HEDTA and F- < 1 mM. Leaf and stem F concentrations increased exponentially as solution F- increased linearly, with nearly no F partitioning into the seed. Results suggest that F was taken up as HF0 while F- uptake was likely restricted. Additionally, F- competed with HA for Ca, thus preventing the formation of Ca-HA flocculents. The addition of soluble Ca resulted in the precipitation of CaF2 solids on the root surface, as determined by tissue analysis and energy dispersive X-ray spectroscopy.

NASA Discipline Life Support Systems↗
NASA NTRS1990

Defect Clustering and Nano-Phase Structure Characterization of Multi-Component Rare Earth Oxide Doped Zirconia-Yttria Thermal Barrier Coatings

Advanced oxide thermal barrier coatings have been developed by incorporating multi- component rare earth oxide dopants into zirconia-yttria to effectively promote the creation of the thermodynamically stable, immobile oxide defect clusters and/or nano-scale phases within the coating systems. The presence of these nano-sized defect clusters has found to significantly reduce the coating intrinsic thermal conductivity, improve sintering resistance, and maintain long-term high temperature stability. In this paper, the defect clusters and nano-structured phases, which were created by the addition of multi-component rare earth dopants to the plasma- sprayed and electron-beam physical vapor deposited thermal barrier coatings, were characterized by high-resolution transmission electron microscopy (TEM). The defect cluster size, distribution, crystallographic and compositional information were investigated using high-resolution TEM lattice imaging, selected area diffraction (SAD), and energy dispersive spectroscopy (EDS) analysis techniques. The results showed that substantial defect clusters were formed in the advanced multi-component rare earth oxide doped zirconia-yttria systems. The size of the oxide defect clusters and the cluster dopant segregation was typically ranging fiom 5 to 50 nm. These multi-component dopant induced defect clusters are an important factor for the coating long-term high temperature stability and excellent performance.

Zhu, Dongming↗