Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Investigation of the Effects of Leading-edge Chord-extensions and Fences in Combination with Leading-edge Flaps on the Aerodynamic Characteristics at Mach Numbers from 0.40 to 0.93 of a 45 Degree Sweptback Wing of Aspect Ratio 4

This investigation was made to determine the effects of 6 degree full-spoan and 3 degree partial-span leading-edge flaps in combination with chord-extensions or fences on the aerodynamic characteristics of a wing-fuselage configuration with a 45 degree sweptback wing of aspect ratio 4, taper ratio 0.3, and NACA 65A006 airfoil sections. The investigation was made in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.40 to 0.93 and an angle-of-attack range of about -2 degrees to 24 degrees. Lift, drag, and pitching-moment data were obtained for all configurations. From overall considerations of stability and performance it appears that with the model of this investigation the 6 degree full-span leading-edge flaps in combination with the chord-extension over the outboard 35 percent of the span, with or without leading-edge camber, would be the most desirable configuration.

Spreeman, Kenneth P↗
NASA NTRS1951

Investigation of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model of the Douglas XF4D-1 Airplane in the Langley Free-Flight Tunnel TED No. NACA DE 349

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the Douglas XF4D-1 airplane has been made in the Langley free-flight tunnel. The model was flown with leading-edge slats retracted and extended over a lift-coefficient range from 0.5 to the stall. Only relatively low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls. The longitudinal stability and control characteristics of the model were satisfactory for all conditions investigated except near the stall with slats extended, where the model had a slight nosing-up tendency. The lateral stability and control characteristics of the model were considered satisfactory for all conditions investigated except near the stall with slats retracted, where a change in sign of the static- directional-stability parameter Cn(sub beta) caused the model to be directionally divergent. The addition of an extension to the top of the vertical tail did not increase Cn(sub beta) enough to eliminate the directional divergence of the model, but a large increase in Cn(sub beta) that was obtainable by artificial means appeared to eliminate the divergence and flights near the stall could be made. Artificially increasing the stability derivative-Cn(sub r) (yawing moment due to yawing) and Cn(sub p) (yawing moment due to rolling) had little effect on the divergence for the range of these parameters investigated. Calculations indicate that the damping of the lateral oscillation of the airplane with slats retracted or extended will be satisfactory at sea level but will be only marginally satisfactory at 40,000 feet.

Johnson, Joseph L.↗
NASA NTRS1986

Natural laminar flow and airplane stability and control

Location and mode of transition from laminar to turbulent boundary layer flow have a dominant effect on the aerodynamic characteristics of an airfoil section. The influences of these parameters on the sectional lift and drag characteristics of three airfoils are examined. Both analytical and experimental results demonstrate that when the boundary layer transitions near the leading edge as a result of surface roughness, extensive trailing-edge separation of the turbulent boundary layer may occur. If the airfoil has a relatively sharp leading-edge, leading-edge stall due to laminar separation can occur after the leading-edge suction peak is formed. These two-dimensional results are used to examine the effects of boundary layer transition behavior on airplane longitudinal and lateral-directional stability and control.

Vandam, Cornelis P.↗
NASA NTRS1975

Diagnostic calculations of airframe-radiated noise

Methods of calculating airframe noise due to the following components are presented: wings and stabilizers, flaps, landing gear 'self-noise', landing gear bay (wheel well) oscillations, separated flow interaction with edges of cavities, and doors associated with gear deployment. The predominant source mechanisms were dipole-like in nature, being related to the local fluctuating aerodynamic forces on struts, airfoil edges, cavity edges, etc. Available data are converted into semiempirical prediction methods to enable a tentative rank ordering of noise sources. A sample application of these prediction procedures is carried out for a typical CTOL passenger jet using actual aircraft parameters, where available.

Hayden, R. E.↗
NASA NTRS1976

Nonlinear slender wing aerodynamics

On present day high performance aircraft, a large portion of the lift is generated by leading edge vortices generated by flow separation off the highly swept leading edges of the lifting surfaces employed. It has been shown in an earlier paper how the vortex effects can be superimposed on a modified slender wing theory to give the unsteady longitudinal characteristics of sharp-edged delta wings up to very high angles of attack. The present paper extends the previous analysis to include the effects of leading edge roundness and trailing edge sweep on the aerodynamic characteristics. The paper also derives analytic means for prediction of the yaw stability of slender wings and the first order effects of Mach number. Universal scaling laws are defined for rapid preliminary design estimates of the slender wing lift and rolling moment. The results indicate that simple analytic tools can be developed to predict the aeroelastic characteristics of the space shuttle ascent configuration with its complicated flow field and aeroelastic cross-couplings.

Ericsson, L. E.↗
NASA NTRS1983

Breakdown of organic insulators

Solar cells and their associated electrical interconnects and leads were encapsulated in transparent elastomeric materials. Their purpose in a photovoltaic module, one of the most important for these elastomeric encapsulation materials, is to function as electrical insulation. This includes internal insulation between adjacent solar cells, between other encapsulated electrical parts, and between the total internal electrical circuitry and external metal frames, grounded areas, and module surfaces. Catastrophic electrical breakdown of the encapsulant insulation materials or electrical current through these materials or module edges to external locations can lead to module failure and can create hazards to humans. Electrical insulation stability, advanced elastomeric encapsulation materials are developed which are intended to be intrinsically free of in-situ ionic impurities, have ultralow water absorption, be weather-stable (UV, oxygen), and have high mechanical flexibility. Efforts to develop a method of assessing the life potential of organic insulation materials in photovoltaic modules are described.

Cuddihy, E. F.↗
NASA NTRS1987

Stability of three-dimensional boundary layers

The computational modeling of the transition process characteristic of flows over swept wings is discussed. Specifically, the crossflow instability and crossflow/Tollmien-Schlichting wave interactions are analyzed through the numerical solution of the full three-dimensional Navier-Stokes equations including unsteadiness, curvature, and sweep. This approach is chosen because of the complexity of the problem and because it appears that regular stability theory is insufficient to explain the discrepancies between experiments and between theory and experiment. The leading edge region of a swept wing will be considered in a three-dimensional spatial simulation with random disturbances as the initial conditions.

Reed, Helen L.↗
NASA NTRS1990

The stability of a collisionless cosmological shell

The P3 M technique is used here to simulate the evolution of collisionless shells in an Omega = 1 universe. Starting from the spherical similarity solution, a bootstrap technique is used to follow the evolution over very large expansion factors. It is found that the overall structure follows the similarity solution for a long period during which bound clumps grow within the shell. At late times the growth of structure depends on induced velocity perturbations in material outside the shell. If such perturbations are suppressed, structure on the shell becomes self-similar. When induced motions in the background medium are included, the evolution at late times is dominated by large-scale modes as predicted by linear stability analysis. The stable final state appears to consist of one or two massive clumps on the edge of a spherical void. The possible application of these results to the origin of galaxies and large-scale structure is discussed.

White, Simon D. M.↗
NASA NTRS1959

A Concept of a Manned Satellite Reentry Which is Completed with a Glide Landing

A concept for a manned satellite reentry from a near space orbit and a glide landing on a normal size airfield is presented. The reentry vehicle configuration suitable for this concept would employ a variable geometry feature in order that the reentry could be made at 90 deg. angle of attack and the landing could be made with a conventional glide approach. Calculated results for reentry at a flight-path angle of -1 deg. show that with an accuracy of 1 percent in the impulse of a retrorocket, the desired flight-path angle at reentry can be controlled within 0.02 deg. and the distance traveled to the reentry point, within 100 miles. The reentry point is arbitrarily defined as the point at which the satellite passes through an altitude of about 70 miles. Misalignment of the retrorocket by 10 deg. increased these errors by as much as 0.02 deg. and 500 miles. Intra-atmospheric trajectory calculations show that pure drag reentries starting with flight-path angles of -1 deg. or less produce a peak deceleration of 8g. Lift created by varying the angle of attack between 90 and 60 deg. is effective in decreasing the maximum deceleration and allows the range to the "recovery" point (where transition is made from reentry to gliding flight) to be increased by as much as 2,300 miles. A sideslip angle of 30 deg. allows lateral displacement of the flight path by as much as 60 deg. miles. Reaction controls would provide control-attitude alignment during the orbit phase. For the reentry phase this configuration should have low static longitudinal and roll stability in the 90 deg. angle-of-attack attitude. Control could be effected by leading-edge and trailing-edge flaps. Transition into the landing phase would be accomplished at an altitude of about 100,000 feet by unfolding the outer wing panels and pitching over to low angles of attack. Calculations indicate that glides can be made from the recovery point to airfields at ranges of from 150 to 200 miles, depending upon the orientation with respect to the original course.

Cheatham, Donald C.↗
NASA NTRS1945

Wind-Tunnel Tests of a 1/5-Scale Semispan Model of the Republic XF-12 Horizontal Tail Surface

Wind-tunnel tests of a 1/5-scale semispan model of the Republic XF-12 horizontal tail surface equipped with an internally balanced elevator were conducted in the 6- by 6-foot test section of the Langley stability tunnel. The tests included measurements of the aerodynamic characteristics of the horizontal tail with and without a beveled trailing edge and also included measurements of the tab characteristics. The variation of the aerodynamic characteristics with boundary-layer conditions and leakage in the internal-balance chambers, measurements of the boundary-layer displacement thickness near the elevator hinge axis, and pressure distributions at the mean geometric chord were also obtained. The results showed that the hinge-moment characteristics of the elevator were critical to boundary-layer conditions and internal-balance leakage. Increasing the boundary-layer displacement thickness by use of roughness strips reduced the rate of change of elevator hinge moments with tab deflection by about 20 percent. The present horizontal tail appears to be unsatisfactory for longitudinal stability with power on, however, an increase in horizontal-tail lift effectiveness should correct this difficulty. The maneuvering stick force per unit acceleration will be extremely critical to minor variations of the elevator hinge moments if the elevator is linked directly to the stick.

Denaci, H. G.↗
NASA NTRS1986

Boundary-layer transition effects on airplane stability and control

Surface contamination of laminar-flow airfoils can significantly modify the location of transition from laminar-to-turbulent boundary-layer flow. The contamination can be the result of insect debris, environmental effects such as ice crystals and moisture due to mist or rain, surface damage, or other contamination adhering to the surface. Location and mode of transition have a dominant effect on the lift-and-drag characteristics of a lifting surface. The influences of laminar boundary-layer flow behavior on airplane stability and control are examined through theoretical results and experimental (wind-tunnel and free-flight) data. For certain airfoils with a relatively steep pressure recovery it is shown that loss of laminar flow near the leading edge can result in premature separation of the turbulent boundary layer and, consequently, in loss of lift and control effectiveness. Aerodynamic modifications which minimize boundary-layer transition effects on airplane stability and control are also discussed.

Van Dam, C. P.↗
NASA NTRS1955

Investigation in the Langley Free-Flight Tunnel of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model Simulating the Convair F-102A Airplane

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model simulating the Convair F-102A airplane has been made in the Langley free-flight tunnel. The model in its basic configuration and with two modifications involving leading- edge slats and an increase in vertical-tail size was flown through a lift-coefficient range from 0.7 to the stall. Only relatively low-altitude conditions were simulated. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the lift-coefficient range investigated, except near the stall, where large values of static directional instability caused the model to be directionally divergent. An 80-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered acceptable over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Boisseau, Peter C.↗
NASA NTRS2024

Aeroelastic Stability Assessment Methodology and Application to Slat Noise Treatments on the High-Lift Common Research Model

This work supports a larger effort at NASA to reduce airframe noise and, thus, environmental noise around airports. The leading-edge slat of conventional high-lift systems is a prominent source of airframe noise, and two technologies were previously identified as promising for noise reduction without significant aerodynamic or weight penalty: the slat cove filler (SCF) and the slat gap filler (SGF). NASA fabricated a 10%-scale semispan aircraft model for wind tunnel testing based upon the High-Lift Common Research Model (CRM-HL). NASA embarked on a test campaign with the 10% CRM-HL to determine the noise reduction effectiveness and other performance metrics of 3D SCF and SGF treatments in flow conditions representative of flight. The highly flexible SCF and SGF treatments posed a risk to the model and aeroelastic instability would compromise research integrity, so aeroelastic stability assessment was required. This work briefly describes the 10% CRM-HL, design of the SCF and SGF treatments to the model, and supporting fluid structure interaction (FSI) research. Relations for static and dynamic aeroelastic similitude are then developed for convenience of reference, and simplifications are introduced of particular utility to the cases considered in this study. The similitude relations are employed to assess the stability of the treatments under wind tunnel flow conditions based upon known behaviors from the supporting research. It is shown that the treatments are safe for test under the anticipated wind tunnel flow conditions with significant margins/factors of safety. It is furthermore demonstrated that the SCF is more susceptible to aeroelastic instability than the SGF, which has implications for flight feasibility.

Similitude↗
NASA NTRS1999

Unstructured Grid Euler Method Assessment for Longitudinal and Lateral/Directional Stability Analysis of the HSR Reference H Configuration at Transonic Speeds

Transonic Euler computations, based on unstructured grid methodology, are performed for a proposed High Speed Civil Transport (HSCT) configuration, designated as the Reference H configuration within the High Speed Research (HSR) Program. The predicted results are correlated with appropriate experimental wind-tunnel data for the baseline configuration with and without control surface deflections for a range of angle of attack at M(sub infinity) = 0.95. Good correlations between the predictions and measured data have been obtained for the longitudinal aerodynamic characteristics of the baseline configuration. The incremental effects in the longitudinal aerodynamic characteristics due to horizontal rail deflections as well as wing leading-edge and trailing-edge flap deflections have also been predicted reasonably well. Computational results and correlations with data are also presented for the lateral and directional stability characteristics for a range of angle of attack at a constant sideslip angle as well as a range of sideslip angles at a constant angle of attack. In addition, the results are presented to assess the computational method performance and convergence characteristics.

Ghaffari, Farhad↗
NASA NTRS1977

Unsteady flow in a supersonic cascade with strong in-passage shocks

Linearized theory is used to study the unsteady flow in a supersonic cascade with in-passage shock waves. We use the Wiener-Hopf technique to obtain a closed-form analytical solution for the supersonic region. To obtain a solution for the rotational flow in the subsonic region we must solve an infinite set of linear algebraic equations. The analysis shows that it is possible to correlate quantitatively the oscillatory shock motion with the Kutta condition at the trailing edges of the blades. This feature allows us to account for the effect of shock motion on the stability of the cascade. Unlike the theory for a completely supersonic flow, the present study predicts the occurrence of supersonic bending flutter. It therefore provides a possible explanation for the bending flutter that has recently been detected in aircraft-engine compressors at higher blade loadings.

Goldstein, M. E.↗
NASA NTRS1978

Study of aerodynamic technology for VSTOL fighter/attack aircraft: Vertical attitude concept

The aerodynamic technology for a vertical attitude VSTOL (VATOL) supersonic fighter/attack aircraft was studied. The selected configuration features a tailless clipped delta wing with leading-edge extension (LEX), maneuvering flaps, top-side inlet, twin dry engines and vectoring nozzles. A relaxed static stability is employed in conjunction with the maneuvering flaps to optimize transonic performance and minimize supersonic trim drag. Control for subaerodynamic flight is obtained by gimballing the nozzles in combination with wing tip jets. Emphasis is placed on the development of aerodynamic characteristics and the identification of aerodynamic uncertainties. A wind tunnel test program is proposed to resolve these uncertainties and ascertain the feasibility of the conceptual design. Ship interface, flight control integration, crew station concepts, advanced weapons, avionics, and materials are discussed.

Gerhardt, H. A.↗
NASA NTRS1989

Experimental investigation of the F/A-18 vortex flows at subsonic through transonic speeds

A subsonic-to-transonic speed wind tunnel study has been conducted to deepen understanding of the nature and possibilities for control of vortical flows associated with wing leading edge extensions (LEXs) on the F/A-18 aircraft; these vortical phenomena encompass vortex breakdown and vortex interactions with vertical stabilizers. Wind tunnel results were correlated with in-flight flow visualizations as well as handling-qualities trend data from a USN F-18 with LEX fences to improve the vertical tail buffet environment. Attention is given to the sensitivity of the vortex flows to Re and Mach numbers, reduced vertical tail excitation due to the presence of a LEX fence, and the interpretation of off-body flow visualizations.

Erickson, Gary E.↗
NASA NTRS1989

Navier-Stokes simulation of the crossflow instability in swept-wing flows

The computational modeling of the transition process characteristic of flows over swept wings are described. Specifically, the crossflow instability and crossflow/T-S wave interactions are analyzed through the numerical solution of the full three-dimensional Navier-Stokes equations including unsteadiness, curvature, and sweep. This approach is chosen because of the complexity of the problem and because it appears that linear stability theory is insufficient to explain the discrepancies between different experiments and between theory and experiments. The leading edge region of a swept wing is considered in a three-dimensional spatial simulation with random disturbances as the initial conditions. The work has been closely coordinated with the experimental program of Professor William Saric, examining the same problem. Comparisons with NASA flight test data and the experiments at Arizona State University were a necessary and an important integral part of this work.

Reed, Helen L.↗