Search NASA⌕ Search

SEARCH · Search NASA

Results for “electricity use”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

International Space Station-Based Electromagnetic Launcher for Space Science Payloads

A method was developed of lowering the cost of planetary exploration missions by using an electromagnetic propulsion/launcher, rather than a chemical-fueled rocket for propulsion. An electromagnetic launcher (EML) based at the International Space Station (ISS) would be used to launch small science payloads to the Moon and near Earth asteroids (NEAs) for the science and exploration missions. An ISS-based electromagnetic launcher could also inject science payloads into orbits around the Earth and perhaps to Mars. The EML would replace rocket technology for certain missions. The EML is a high-energy system that uses electricity rather than propellant to accelerate payloads to high velocities. The most common type of EML is the rail gun. Other types are possible, e.g., a coil gun, also known as a Gauss gun or mass driver. The EML could also "drop" science payloads into the Earth's upper

Jones, Ross M.↗
NASA NTRS2012

Dual-Mode Scramjet Flameholding Operability Measurements

Flameholding measurements were made in two different direct connect combustor facilities that were designed to simulate a cavity flameholder in the flowfield of a hydrocarbon fueled dual-mode scramjet combustor. The presence of a shocktrain upstream of the flameholder has a significant impact on the inlet flow to the combustor and on the flameholding limits. A throttle was installed in the downstream end of the test rigs to provide the needed back-pressurization and decouple the operation of the flameholder from the backpressure formed by heat release and thermal choking, as in a flight engine. Measurements were made primarily with ethylene fuel but a limited number of tests were also performed with heated gaseous JP-7 fuel injection. The flameholding limits were measured by ramping inlet air temperature down until blowout was observed. The tests performed in the United Technologies Research Center (UTRC) facility used a hydrogen fueled vitiated air heater, Mach 2.2 and 3.3 inlet nozzles, a scramjet combustor rig with a 1.666 by 6 inch inlet and a 0.65 inch deep cavity. Mean blowout temperature measured at the baseline condition with ethylene fuel, the Mach 2.2 inlet and a cavity pressure of 21 psia was 1502 oR. Flameholding sensitivity to a variety of parameters was assessed. Blowout temperature was found to be most sensitive to fuel injection location and fuel flowrates and surprisingly insensitive to operating pressure (by varying both back-pressurization and inlet flowrate) and inlet Mach number. Video imaging through both the bottom and side wall windows was collected simultaneously and showed that the flame structure was quite unsteady with significant lateral movements as well as movement upstream of the flameholder. Experiments in the University of Virginia (UVa) test facility used a Mach 2 inlet nozzle with a 1 inch by 1.5 inch exit cross section, an aspect ratio of 1.5 versus 3.6 in the UTRC facility. The UVa facility tests were designed to measure the sensitivity of flameholding limits to inlet air vitiation by using electrically heated air and adding steam at levels to simulate vitiated air heaters. The measurements showed no significant difference in blowout temperature with inlet air mole fractions of steam from 0 to 6.7%.

airbreathing engines aircraft↗
NASA NTRS2008

Thermal Expansion Studies of Selected High Temperature Thermoelectric Materials

Radioisotope thermoelectric generators (RTGs) generate electrical power by converting the heat released from the nuclear decay of radioactive isotopes (typically plutonium-238) into electricity using a thermoelectric converter. RTGs have been successfully used to power a number of space missions and have demonstrated their reliability over an extended period of time (tens of years) and are compact, rugged, radiation resistant, scalable, and produce no noise, vibration or torque during operation. System conversion efficiency for state-of-practice RTGs is about 6% and specific power less than or equal to 5.1 W/kg. Higher specific power would result in more on-board power for the same RTG mass, or less RTG mass for the same on-board power. The Jet Propulsion Laboratory has been leading, under the advanced thermoelectric converter (ATEC) project, the development of new high-temperature thermoelectric materials and components for integration into advanced, more efficient RTGs. Thermoelectric materials investigated to date include skutterudites, the Yb14MnSb11 compound, and SiGe alloys. The development of long-lived thermoelectric couples based on some of these materials has been initiated and is assisted by a thermo-mechanical stress analysis to ensure that all stresses under both fabrication and operation conditions will be within yield limits for those materials. Several physical parameters are needed as input to this analysis. Among those parameters, the coefficient of thermal expansion (CTE) is critically important. Thermal expansion coefficient measurements of several thermoelectric materials under consideration for ATEC are described in this paper. The stress response at the interfaces in material stacks subjected to changes in temperature is discussed, drawing on work from the literature and project-specific tools developed here. The degree of CTE mismatch and the associated effect on the formation of stress is highlighted.

silicon germanium↗
NASA NTRS2015

Lightweight Integrated Solar Array and Transceiver

The Lightweight Integrated Solar Array and Transceiver (LISA-T) project will leverage several existing and on-going efforts at Marshall Space Flight Center (MSFC) for the design, development, fabrication, and test of a launch stowed, orbit deployed structure on which thin-film photovoltaics for power generation and antenna elements for communication, are embedded. Photovoltaics is a method for converting solar energy into electricity using semiconductor materials. The system will provide higher power generation with a lower mass, smaller stowage volume, and lower cost than the state of the art solar arrays, while simultaneously enabling deployable antenna concepts.

Thin-film photovoltaics↗
NASA NTRS2016

LED Lighting and Plant Growth: Supplemental LED Effects on Development

The growth of plants aboard the International Space Station (ISS) will play a pivotal role in advancing human space exploration to further uncharted destinations. Not only will plants be useful for oxygen production and carbon dioxide reduction, they will also serve as a supplemental food source for the astronaut diet. Research indicates that the most efficient way for these crops to be grown is by using electric lighting – specifically light-emitting diodes (LED) due to their several unique advantages. One of these advantages includes the potential for selecting certain wavelengths. By isolating certain lights, the effects of specific wavelengths on plant growth can be made clearer. This research project examined plant morphology, chlorophyll, biomass production, and nutrient synthesis in ‘Outredgeous’ red romaine lettuce grown under six LED light treatments of white (W), W + blue (B), W + green (G), W + red (R), W + far red (FR), and a Heliospectra lamp (Helio) (-composed of B+G+R+FR LEDs without W LEDS-). It was consistently found that the lettuce grown under the Helio, W + FR, W + R, and W + G treatments all showed improved physiology in terms of shoot length, shoot diameter, fresh mass, and dry mass relative to the W control. The Helio, W + FR, and W + G treatments exhibited significantly larger leaf areas while the Helio and W + FR treatments also produced more leaves on average at 28 days after planting (DAP). The W (control) and W + B treatments showed the highest accumulation of chlorophyll at 28 DAP. In conclusion, lettuce grown under the Helio treatment may be the overall most beneficial for supplementing the astronaut diet in terms of total edible biomass produced in a 28 day crop cycle.

LED↗
NASA NTRS2021

Design of Solar Sailing Trajectories Resilient to Safe Mode Events

Solar sails are an enabling technology for stand-alone small-satellite deep-space exploration. However, their always-on nature, combined with the time of flight required for deep-space missions, makes them particularly susceptible to safe mode events. Unlike missions using electric propulsion, exclusively solar sail- ing missions cannot carry extra propellant to make up for a safe mode event, and more powerful methods like expected availability cannot be directly applied. This work extends the expected availability and duty cycle approaches to solar sailing. Through an application to NASA’s Solar Cruiser mission, a 46 % increase in tra- jectory resilience is obtained at negligible change in the mission’s time of flight. Additionally, it is shown that when a safe mode event stops the spacecraft from reaching its target orbit, the developed methods reduce the expected final error by approximately an order of magnitude.

Johnson, Les↗
NASA NTRSDate not supplied

Control and Scaling Approach for the Emulation of Dynamic Subscale Torque Loads

Research and development of electrified aircraft propulsion powertrains is moving toward the use electro-mechanical systems to emulate the loads a system imparts on another. Replacing a prime mover with a model driving an electro-mechanical system capable of emulating loads that regulate the system to produce a desired response is a lower risk, lower cost alternative to using the traditional prime mover for control system verification. This paper outlines a control and scaling approach for emulating scaled dynamic torque loads using electric machine (EM) hardware for electrified aircraft propulsion research and development purposes. The approach, known as the Sliding Mode Impedance Controller with Scaling (SMICS), drives a mechanically coupled two-EM system that provides a scaled hardware representation of an electrified turbomachinery shaft. One EM reflects inertial dynamics and load of the shaft under steady-state and transient operation while the second EM represents a motor/generator connected to the shaft. This closed loop system applies impedance and sliding mode control schemes to match desired dynamics in real-time along with parameter scaling to effectively scale full scale torque inputs, a full-scale desired inertia, and sub-scale speed feedback. The result is a sub-scale hardware implementation of a coupled EM system that is command-able by a model and control system designed for a full-scale electrified aircraft propulsion powertrain. The paper elaborates on the need for closed loop control and scaling as well as impedance and sliding mode control theory, shows a derivation of the controller and scaling, its implementation, and presents a comparison of theoretical and actual simulation results acquired during hardware-in-the-loop testing of a partial turboelectric propulsion concept at the NASA Electric Aircraft Testbed (NEAT).

Santino J Bianco↗
NASA NTRS2024

Electrodynamic Dust Shield for Active Dust Mitigation of Thermal Radiators

This project sought to investigate whether the Electrodynamic Dust Shield (EDS) would work with various thermal control coatings (TCC) to remove dust off the TCC. Keeping surfaces dust free is essential for thermal radiators as the dust acts as both a blackbody and a thermal insulator so it will absorb more sunlight and prevent the radiator from radiating heat. The lack of heat rejection on dusty surfaces causes the radiator to be oversized and potentially cause catastrophic system failure due to overheating. With an EDS integrated into the radiator system, dust impacts can be mitigated by removing the dust off the surface using electric fields. This project tested dust removal, solar absorptance, emittance, and limited thermal vacuum with a TCC on an EDS which is bonded to an aluminum plate acting like a radiator. The results of various coatings suggests that the EDS can work with insulative TCC in high vacuum for removing dust, and that after removing dust, the solar absorptance can be restored to within 5-10% of its original value when the EDS works properly. More work is necessary to determine how the EDS impacts the emittance of the whole radiator system and bonding between the different layers needs to be investigated to withstand temperature cycling of the moon without delamination occurring.

Krystal Acosta↗
NASA NTRS1983

Visible light to electrical energy conversion using photoelectrochemical cells

Sustained conversion of low energy visible or near i.r. light (>1.25 eV) to electrical energy has been obtained using wet photoelectrochemical cells where there are no net chemical changes in the system. Stabilization of n-type semi-conductor anodes of CdS, CdSe, CdTe, GaP, GaAs and InP to photoanodic dissolution is achieved by employing selected alkaline solutions of Na.sub.2 S, Na.sub.2 S/S, Na.sub.2 Se, Na.sub.2 Se/Se, Na.sub.2 Te and Na.sub.2 Te/Te as the electrolyte. The oxidation of (poly) sulfide, (poly)selenide or (poly)telluride species occurs at the irradiated anode, and reduction of polysulfide, polyselenide or polytelluride species occurs at the dark Pt cathode of the photoelectrochemical cell. Optical to electrical energy conversion efficiencies approaching 15% at selected frequencies have been observed in some cells. The wavelength for the onset of photocurrent corresponds to the band gap of the particular anode material used in the cell.

Wrighton, Mark S.↗
NASA NTRS1979

Use of composites in electric vehicles

Report presents study of weight savings in electric vehicles by using alternative structural materials, particularly composites. Topics discussed include safety, aerodynamics, esthetics, and cost.

Dawe, R. H.↗
NASA NTRS1992

High efficiency thermal to electric energy conversion using selective emitters and spectrally tuned solar cells

Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1500 K. Depending on the nature of parasitic losses, overall thermal-to-electric conversion efficiencies greater than 20 percent are feasible.

Chubb, Donald L.↗
NASA NTRS1952

Preliminary Investigation of Cyclic De-Icing of an Airfoil Using an External Electric Heater

An investigation was conducted in the NACA Lewis icing research tunnel to determine the characteristics and requirements of cyclic deicing of a 65,2-216 airfoil by use of an external electric heater. The present investigation was limited to an airspeed of 175 miles per hour. Data are presented to show the effects of variations in heat-on and heat-off periods, ambient air temperature, liquid-water content, angle of attack, and. heating distribution on the requirements for cyclic deicing. The external heat flow at various icing and heating conditions is also presented. A continuously heated parting strip at the airfoil leading edge was found necessary for quick, complete, and consistent ice removal. The cyclic power requirements were found to be primarily a function of the datum temperature and heat-on time, with the other operating and meteorological variables having a second-order effect. Short heat-on periods and high power densities resulted in the most efficient ice removal, the minimum energy input, and the minimum runback ice formations. The optimum chordwise heating distribution pattern was found to consist of a uniform distribution of cycled power density in the impingement region. Downstream of the impingement region the power density decreased to the limits of heating which, for the conditions investigated, extended from 5.7 percent chord on the upper surface of the airfoil to 8.9 percent chord on the lower surface. Ice removal did not take place at a heater surface temperature of 32 F; surface temperatures of approximately 50 to 100 F were required to effect removal. Better de-icing performance and greater energy savings would be possible with a heater having a higher thermal efficiency.

Lewis, James P.↗
NASA NTRS1992

Directional solidification processing of alloys using an applied electric field

A method is provided for obtaining an alloy having an ordered microstructure which comprises the steps of heating the central portion of the alloy under uniform temperature so that it enters a liquid phase while the outer portions remain solid, applying a constant electric current through the alloy during the heating step, and solidifying the liquid central portion of the alloy by subjecting it to a temperature-gradient zone so that cooling occurs in a directional manner and at a given rate of speed while maintaining the application of the constant electric current through the alloy. The method is particularly suitable for use with nickel-based superalloys. The method of the present invention produces an alloy having superior characteristics such as reduced segregation. After subsequent precipitation by heat-treatment, the alloys produced by the present invention will have excellent strength and high-temperature resistance.

McKannan, Eugene C.↗
NASA NTRS1991

Automating a spacecraft electrical power system using expert systems

Since Skylab, Marshall Space Flight Center (MSFC) has recognized the need for large electrical power systems (EPS's) in upcoming Spacecraft. The operation of the spacecraft depends on the EPS. Therefore, it must be efficient, safe, and reliable. In 1978, as a consequence of having to supply a large number of EPS personnel to monitor and control Skylab, the Electrical power Branch of MSFC began the autonomously managed power system (AMPS) project. This project resulted in the assembly of a 25-kW high-voltage dc test facility and provided the means of getting man out of the loop as much as possible. AMPS includes several embedded controllers which allow a significant level of autonomous operation. More recently, the Electrical Division at MSFC has developed the space station module power management and distribution (SSM/PMAD) breadboard to investigate managing and distributing power in the Space Station Freedom habitation and laboratory modules. Again, the requirement for a high level of autonomy for the efficient operation over the lifetime of the station and for the benefits of enhanced safety has been demonstrated. This paper describes the two breadboards and the hierarchical approach to automation which was developed through these projects.

Lollar, L. F.↗