Search NASA⌕ Search

SEARCH · Search NASA

Results for “engine modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

Aircraft flying in regions of high ice crystal concentrations are susceptible to the buildup of ice within the compression system of their gas turbine engines. This ice buildup can restrict engine airflow and cause an uncommanded loss of thrust, also known as engine rollback, which poses a potential safety hazard. The aviation community is conducting research to understand this phenomena, and to identify avoidance and mitigation strategies to address the concern. To support this research, a dynamic turbofan engine model has been created to enable the development and evaluation of engine icing detection and control-based mitigation strategies. This model captures the dynamic engine response due to high ice water ingestion and the buildup of ice blockage in the engines low pressure compressor. It includes a fuel control system allowing engine closed-loop control effects during engine icing events to be emulated. The model also includes bleed air valve and horsepower extraction actuators that, when modulated, change overall engine operating performance. This system-level model has been developed and compared against test data acquired from an aircraft turbofan engine undergoing engine icing studies in an altitude test facility and also against outputs from the manufacturers customer deck. This paper will describe the model and show results of its dynamic response under open-loop and closed-loop control operating scenarios in the presence of ice blockage buildup compared against engine test cell data. Planned follow-on use of the model for the development and evaluation of icing detection and control-based mitigation strategies will also be discussed. The intent is to combine the model and control mitigation logic with an engine icing risk calculation tool capable of predicting the risk of engine icing based on current operating conditions. Upon detection of an operating region of risk for engine icing events, the control mitigation logic will seek to change the engines operating point to a region of lower risk through the modulation of available control actuators while maintaining the desired engine thrust output. Follow-on work will assess the feasibility and effectiveness of such control-based mitigation strategies.

engine control↗
NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

Aircraft flying in regions of high ice crystal concentrations are susceptible to the buildup of ice within the compression system of their gas turbine engines. This ice buildup can restrict engine airflow and cause an uncommanded loss of thrust, also known as engine rollback, which poses a potential safety hazard. The aviation community is conducting research to understand this phenomena, and to identify avoidance and mitigation strategies to address the concern. To support this research, a dynamic turbofan engine model has been created to enable the development and evaluation of engine icing detection and control-based mitigation strategies. This model captures the dynamic engine response due to high ice water ingestion and the buildup of ice blockage in the engines low pressure compressor. It includes a fuel control system allowing engine closed-loop control effects during engine icing events to be emulated. The model also includes bleed air valve and horsepower extraction actuators that, when modulated, change overall engine operating performance. This system-level model has been developed and compared against test data acquired from an aircraft turbofan engine undergoing engine icing studies in an altitude test facility and also against outputs from the manufacturers customer deck. This paper will describe the model and show results of its dynamic response under open-loop and closed-loop control operating scenarios in the presence of ice blockage buildup compared against engine test cell data. Planned follow-on use of the model for the development and evaluation of icing detection and control-based mitigation strategies will also be discussed. The intent is to combine the model and control mitigation logic with an engine icing risk calculation tool capable of predicting the risk of engine icing based on current operating conditions. Upon detection of an operating region of risk for engine icing events, the control mitigation logic will seek to change the engines operating point to a region of lower risk through the modulation of available control actuators while maintaining the desired engine thrust output. Follow-on work will assess the feasibility and effectiveness of such control-based mitigation strategies.

engine control↗
NASA NTRS1978

Alternatives for jet engine control

General goals of the research were classified into two categories. The first category involves the use of modern multivariable frequency domain methods for control of engine models in the neighborhood of a quiescent point. The second category involves the use of nonlinear modelling and optimization techniques for control of engine models over a more extensive part of the flight envelope. In the frequency domain category, works were published in the areas of low-interaction design, polynomial design, and multiple setpoint studies. A number of these ideas progressed to the point at which they are starting to attract practical interest. In the nonlinear category, advances were made both in engine modelling and in the details associated with software for determination of time optimal controls. Nonlinear models for a two spool turbofan engine were expanded and refined; and a promising new approach to automatic model generation was placed under study. A two time scale scheme was developed to do two-dimensional dynamic programming, and an outward spiral sweep technique has greatly speeded convergence times in time optimal calculations.

Leake, R. J.↗
NASA NTRS2023

Modeling Turboshaft Engines for the Revolutionary Vertical Lift Technology Project, Expanded

Turboshaft engine performance and weight models were developed to support conceptual propulsion and vehicle mission design and performance under the Revolutionary Vertical Lift Technology (RVLT) Project in 2019 by Snyder in Reference 7. These models were developed using open data sources, assuming present and future technology levels, and range from 650 to 5,000 output shaft horsepower (485 to 3,730 kW). This paper expands on the previous research, extending the power ranges from 200 to 15000 output shaft horsepower (150 to 11,200 kW) and documenting the methodology, assumptions, and engine performance realizes important benefits for NASA and the aviation community. NASA concept-vehicle study efforts using these baseline propulsion models can be more readily shared among the government, industry, and university community to support present and future work. Assessing the benefits of advanced technologies and new configurations can be facilitated using these models, which helps guide technology investment. As the various conceptual vehicle and mission analysis simulations are developed, these models can be used directly for broader systems analysis studies, including optimization within the propulsion model itself. To expand on the previous effort, the turboshaft engine is briefly discussed, highlighting the specific components, and expected performance characteristics over the updated power range and technology levels considered. Additional engine configurations will also be discussed as they vary based on power output and assumed technology level. Engine performance, such as airflow, power output and weight are updated, noting important trends for system studies. Finally, the effect of advanced propulsion technologies on public reference models including RVLT concept vehicles are reported along with the tools and software methods used to complete the analysis.

VTOL↗
NASA NTRSDate not supplied

Modeling Turboshaft Engines for the Revolutionary Vertical Lift Technology Project, Expanded

Turboshaft engine performance and weight models were developed to support conceptual propulsion and vehicle mission design and performance under the Revolutionary Vertical Lift Technology (RVLT) Project in 2019 by Snyder in Ref. 1. These models were developed using open data sources, assuming present and future technology levels, and range from 650 to 5,000 output shaft horsepower (485 to 3,730 kW). This paper expands on the previous research, extending the power ranges from 200 to 15000 output shaft horsepower (150 to 11,200 kW) and documenting the methodology, assumptions, and engine performance realizes important benefits for NASA and the aviation community. NASA concept vehicle study efforts using these baseline propulsion models can be more readily shared among the government, industry, and university community to support present and future work. Assessing the benefits of advanced technologies and new configurations can be facilitated using these models, which helps guide technology investment. As the various modeling conceptual vehicle and mission analysis environments advance, these models can be used directly for broader systems analysis studies, including optimization within the propulsion model itself. To expand on the previous effort, the turboshaft engine is briefly discussed, highlighting the specific components, and expected performance characteristics over the updated power range and technology levels considered. Additional engine configurations will also be discussed as they vary based on power output and assumed technology level. Engine performance, such as airflow, power output and weight will be updated, noting trends that are important for system studies. Finally, the effect of advanced propulsion technologies on RVLT concept vehicles are also reported along with the tools and software methods used to complete the analysis.

VTOL↗
NASA NTRSDate not supplied

Modeling Turboshaft Engines for the Revolutionary Vertical Lift Technology Project, Expanded

Turboshaft engine performance and weight models were developed to support conceptual propulsion and vehicle mission design and performance under the Revolutionary Vertical Lift Technology (RVLT) Project in 2019 by Snyder in Ref. 1. These models were developed using open data sources, assuming present and future technology levels, and range from 650 to 5,000 output shaft horsepower (485 to 3,730 kW). This paper expands on the previous research, extending the power ranges from 200 to 15000 output shaft horsepower (150 to 11,200 kW) and documenting the methodology, assumptions, and engine performance realizes important benefits for NASA and the aviation community. NASA concept-vehicle study efforts using these baseline propulsion models can be more readily shared among the government, industry, and university community to support present and future work. Assessing the benefits of advanced technologies and new configurations can be facilitated using these models, which helps guide technology investment. As the various modeling conceptual vehicle and mission analysis environments advance, these models can be used directly for broader systems analysis studies, including optimization within the propulsion model itself. To expand on the previous effort, the turboshaft engine is briefly discussed, highlighting the specific components, and expected performance characteristics over the updated power range and technology levels considered. Additional engine configurations will also be discussed as they vary based on power output and assumed technology level. Engine performance, such as airflow, power output and weight will be updated, noting trends that are important for system studies. Finally, the effect of advanced propulsion technologies on RVLT concept vehicles are also reported along with the tools and software methods used to complete the analysis

VTOL↗
NASA NTRS1979

Alternatives for jet engine control

The research is classified in two categories: (1) the use of modern multivariable frequency domain methods for control of engine models in the neighborhood of a set-point, and (2) the use of nonlinear modelling and optimization techniques for control of engine models over a more extensive part of the flight envelope. Progress in the first category included the extension of CARDIAD (Complex Acceptability Region for Diagonal Dominance) methods developed with the help of the grant to the case of engine models with four inputs and four outputs. A suitable bounding procedure for the dominance function was determined. Progress in the second category had its principal focus on automatic nonlinear model generation. Simulations of models produced satisfactory results where compared with the NASA DYNGEN digital engine deck.

Sain, M. K.↗
NASA NTRS2002

NASA Marshall Engineering Thermosphere Model

This Technical Memorandum describes the NASA Marshall Engineering Thermosphere Model-Version 2.0 (MET-V 2.0) and contains an explanation on the use of the computer program along with an example of the MET-V 2.0 model products. The MET-V 2.0 provides an update to the 1988 version of the model. It provides information on the total mass density, temperature, and individual species number densities for any altitude between 90 and 2,500 km as a function of latitude, longitude, time, and solar and geomagnetic activity. A description is given for use of estimated future 13-mo smoothed solar flux and geomagnetic index values as input to the model. Address technical questions on the MET-V 2.0 and associated computer program to Jerry K. Owens, Spaceflight Experiments Group, Marshall Space Flight Center, Huntsville, AL 35812 (256-961-7576; e-mail Jerry.Owens@msfc.nasa.gov).

Owens, J. K.↗
NASA NTRS2003

Engineering-Level Model Atmospheres For Titan and Mars

An engineering-level atmospheric model for Titan has been developed for use in NASA s systems analysis studies of aerocapture and entry, descent and landing (EDL) applications in potential missions to Titan. Analogous to highly successful Global Reference Atmospheric Models for Earth (GRAM) and Mars (Mars-GRAM), the new model is called Titan-GRAM. Like GRAM and Mars-GRAM, an important feature of Titan-GRAM is its ability to simulate quasi-random perturbations for Monte-Carlo analyses in developing guidance, navigation and control algorithms, and for thermal systems design. Titan-GRAM features and sample results will be presented. Features of Mars-GRAM especially related to EDL applications will also be presented and illustrated.

Justus, C. G.↗
NASA NTRS2006

Next-generation concurrent engineering: developing models to complement point designs

Concurrent Engineering Design teams have made routine the rapid development of point designs for space missions. The Jet Propulsion Laboratory's Team X is now evolving into a next generation CED; nin addition to a point design, the team develops a model of the local trade space. The process is a balance between the power of model-developing tools and the creativity of human experts, enabling the development of a variety of trade models for any space mission.

trade space exploration↗
NASA NTRS1982

Computer program for a four-cylinder-Stirling-engine controls simulation

A four cylinder Stirling engine, transient engine simulation computer program is presented. The program is intended for controls analysis. The associated engine model was simplified to shorten computer calculation time. The model includes engine mechanical drive dynamics and vehicle load effects. The computer program also includes subroutines that allow: (1) acceleration of the engine by addition of hydrogen to the system, and (2) braking of the engine by short circuiting of the working spaces. Subroutines to calculate degraded engine performance (e.g., due to piston ring and piston rod leakage) are provided. Input data required to run the program are described and flow charts are provided. The program is modular to allow easy modification of individual routines. Examples of steady state and transient results are presented.

Daniels, C. J.↗
NASA NTRS1986

Four-Cylinder Stirling Engine Control Simulation

Four-cylinder, Stirling-engine, transient-engine-simulation computer program developed. Program intended for control analysis. Associated engine model simplified to shorten computer calculation time. Model includes engine mechanical-drive dynamics and vehicle-load effects. Computer program also includes subroutines that allow acceleration of engine by addition of hydrogen to system and braking of engine by short circuiting of working spaces.

Daniele, C. J.↗
NASA NTRS1992

Overview of magnetic suspension research at Langley Research Center

An overview of research in small- and large-gap magnetic suspension systems at LaRC is presented. The overview is limited to systems which have been built as laboratory models or engineering models. Small-gap systems applications include the Annular Momentum Control Device (AMCD), which is a momentum storage device for the stabilization and control of spacecraft, and the Annular Suspension and Pointing System (ASPS), which is a general purpose pointing mount designed to provide orientation, mechanical isolation, and fine pointing space experiments. These devices are described and control and linearization approaches for the magnetic suspension systems for these devices are discussed. Large-gap systems applications at LaRC have been almost exclusively wind tunnel magnetic suspension systems. A brief description of these efforts is also presented.

Groom, Nelson J.↗
NASA NTRS1993

Measuring Fluctuating Pressures With Recessed Gauges

Report discusses use of pressure gauges mounted in recesses in interior wall of model scramjet engine. Consists of brief memorandum plus excerpts from NASA Technical Paper 3189, "Unsteady Pressure Loads In A Generic High-Speed Engine Model." Focuses mainly on factors affecting accuracy of gauge readings.

Parrott, Tony L.↗
NASA NTRS1992

Performances of the Imaging Proportional Counter of the Stellar X-ray Polarimeter

The Stellar X-ray Polarimeter (SXRP) will be mounted on the focal plane of one of the two SODART telescopes aboard the Russian mission Spectrum-X-gamma. The SXRP employs the same Imaging Proportional Counters for both the Bragg and the scattering stages. An account is presently given of the main characteristics of these detectors and their performance, on the basis of tests at the technical-model and engineering model levels of development.

Costa, E.↗
NASA NTRS1995

Research project for increasing pool of minority engineers

The Tennessee State University (TSU) Research Project for Increasing the Pool of Minority Engineers is designed to develop engineers who have academic and research experiences in technical areas of interest to NASA. These engineers will also have some degree of familiarity with NASA Lewis Research Center as a result of interaction with Lewis engineers, field trips and internships at Lewis. The Research Project has four components, which are: (1) Minority Introduction to Engineering (MITE), a high school precollege program, (2) engineering and technology previews, (3) the NASA LeRC Scholars program which includes scholarships and summer internships, and (4) undergraduate research experiences on NASA sponsored research. MITE is a two-week summer engineering camp designed to introduce minority high school students to engineering by exposing them to: (1) engineering role models (engineering students and NASA engineer), (2) field trips to engineering firms, (3) in addition to introducing youth to the language of the engineer (i.e., science, mathematics, technical writing, computers, and the engineering laboratory). Three MITE camps are held on the campus of TSU with an average of 40 participants. MITE has grown from 25 participants at its inception in 1990 to 118 participants in 1994 with participants from 17 states, including the District of Columbia, and 51 percent of the participants were female. Over the four-year period, 77 percent of the seniors who participated in MITE have gone to college, while 53 percent of those seniors in college are majoring in science, engineering or mathematics (SEM). This first Engineering and Technology Previews held in 1993 brought 23 youths from Cleveland, Ohio to TSU for a two-day preview of engineering and college life. Two previews are scheduled for 1994-1995. The NASA LeRC Scholars program provides scholarships and summer internships for minority engineering students majoring in electrical or mechanical engineering. Presently six (6) engineering students are in the Scholars program. The average GPA for the scholars is 3.239. Each scholar must maintain a minimum GPA of 3.000/4.000. NASA LeRC Fred Higgs has been awarded a GEM Fellowship. In addition, he will be presenting a paper entitled 'Design of Helical Spring Using Probabilistic Design Methodology' at the Middle Tennessee Section ASME Student Design Presentations in Nashville on March 23rd and at the National Conference on Undergraduate Research to be held at Union College, Schenectady, New York on April 20-22, 1995. Each of the scholars is working on one of the three NASA sponsored research projects in the college.

Rogers, Decatur B.↗
NASA NTRS1999

High Speed Civil Transport Aircraft Simulation: Reference-H Cycle 1, MATLAB Implementation

The mathematical model and associated code to simulate a high speed civil transport aircraft - the Boeing Reference H configuration - are described. The simulation was constructed in support of advanced control law research. In addition to providing time histories of the dynamic response, the code includes the capabilities for calculating trim solutions and for generating linear models. The simulation relies on the nonlinear, six-degree-of-freedom equations which govern the motion of a rigid aircraft in atmospheric flight. The 1962 Standard Atmosphere Tables are used along with a turbulence model to simulate the Earth atmosphere. The aircraft model has three parts - an aerodynamic model, an engine model, and a mass model. These models use the data from the Boeing Reference H cycle 1 simulation data base. Models for the actuator dynamics, landing gear, and flight control system are not included in this aircraft model. Dynamic responses generated by the nonlinear simulation are presented and compared with results generated from alternate simulations at Boeing Commercial Aircraft Company and NASA Langley Research Center. Also, dynamic responses generated using linear models are presented and compared with dynamic responses generated using the nonlinear simulation.

Sotack, Robert A.↗