Search NASA⌕ Search

SEARCH · Search NASA

Results for “engine simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

UHB Engine Fan Broadband Noise Reduction Study

A study has been completed to quantify the contribution of fan broadband noise to advanced high bypass turbofan engine system noise levels. The result suggests that reducing fan broadband noise can produce 3 to 4 EPNdB in engine system noise reduction, once the fan tones are eliminated. Further, in conjunction with the elimination of fan tones and an increase in bypass ratio, a potential reduction of 7 to 10 EPNdB in system noise can be achieved. In addition, an initial assessment of engine broadband noise source mechanisms has been made, concluding that the dominant source of fan broadband noise is the interaction of incident inlet boundary layer turbulence with the fan rotor. This source has two contributors, i.e., unsteady life dipole response and steady loading quadrupole response. The quadrupole contribution was found to be the most important component, suggesting that broadband noise reduction can be achieved by the reduction of steady loading field-turbulence field quadrupole interaction. Finally, for a controlled experimental quantification and verification, the study recommends that further broadband noise tests be done on a simulated engine rig, such as the GE Aircraft Engine Universal Propulsion Simulator, rather than testing on an engine statically in an outdoor arena The rig should be capable of generating forward and aft propagating fan noise, and it needs to be tested in a large freejet or a wind tunnel.

Gliebe, Philip R.↗
NASA NTRS1995

Computational Simulation Of A Nuclear Engine

Nuclear Engine System Simulation (NESS) computer program developed to satisfy need for accurate, stand-alone software tool for preliminary design analysis of nuclear thermal propulsion (NTP) engine system. Used for rapid, preliminary detailed design analysis of both reactor and key engine systems. Principal outputs include operating characteristics and weights of reactors, engine-system parameters as performances, weights, dimensions, pressures, temperatures, and mass flows, and operating characteristics of turbopumps under both design and off-design operating conditions. Written in FORTRAN 77.

Walton, J. T.↗
NASA NTRS1955

Free-Spinning-Tunnel Investigation to Determine the Effect of Spin-Recovery Rockets and Thrust Simulation on the Recovery Characteristics of a 1/21-Scale Model of the Chance Vought F7U-3 Airplane, TED No. NACA AD 3103

An investigation of a l/21-scale model of the Chance Vought F7U-3 airplane in the co&at-load- condition has been conducted in the Langley 20-foot free-spinning tunnel, The recovery characteristics of the model were determined by use of spin-recovery rockets for the erect and inverted spinning condition. The rockets were so placed as to provide either a yawing or rolling moment about the model center of gravity. Also included in the investigation were tests to determine the effect of simulated engine thrust on the recovery characteristics of the model. On the basis of model tests, recoveries from erect and inverted spins were satisfactory when a yawing moment of 22,200 foot-pounds (full scale) was provided against the spin by rockets attached to the wing tips; the anti-spin yawing moment was applied for approximately 9 seconds, (full scale). Satisfactory recoveries were obtained from erect spins when a rolling moment of 22,200 foot-pounds (full scale) was provided with the spin (rolls right wing down in right spin). Although the inverted spin was satisfactorily terminated when a rolling moment of equal magnitude was provided, a roll rocket was not considered to be an optimum spin-recovery device to effect recoveries from inverted spins for this airplane because of resulting gyrations during spin recovery. Simulation of engine thrust had no apparent effect on the spin recovery characteristics.

Burk, Sanger H., Jr.↗
NASA NTRS1992

A simulated annealing approach to schedule optimization for the SES facility

The Shuttle Engineering Simulator (SES) is a facility which houses the software and hardware for a variety of simulation systems. The simulators include the Autonomous Remote Manipulator, the Manned Maneuvering Unit, Orbiter/Space Station docking, and shuttle entry and landing. The SES simulators are used by various groups throughout NASA. For example, astronauts use the SES to practice maneuvers with the shuttle equipment; programmers use the SES to test flight software; and engineers use the SES for design and analysis studies. Due to its high demand, the SES is busy twenty-four hours a day and seven days a week. Scheduling the facility is a problem that is constantly growing and changing with the addition of new equipment. Currently a number of small independent programs have been developed to help solve the problem, but the long-term answer lies in finding a flexible, integrated system that provides the user with the ability to create, optimize, and edit the schedule. COMPASS is an interactive and highly flexible scheduling system. However, until recently COMPASS did not provide any optimization features. This paper describes the simulated annealing extension to COMPASS. It now allows the user to interweave schedule creation, revision, and optimization. This practical approach was necessary in order to satisfy the operational requirements of the SES.

Mcmahon, Mary Beth↗
NASA NTRS1993

Space Shuttle Main Engine real time stability analysis

The Space Shuttle Main Engine (SSME) is a reusable, high performance, liquid rocket engine with variable thrust. The engine control system continuously monitors the engine parameters and issues propellant valve control signals in accordance with the thrust and mixture ratio commands. A real time engine simulation lab was installed at MSFC to verify flight software and to perform engine dynamic analysis. A real time engine model was developed on the AD100 computer system. This model provides sufficient fidelity on the dynamics of major engine components and yet simplified enough to be executed in real time. The hardware-in-the-loop type simulation and analysis becomes necessary as NASA is continuously improving the SSME technology, some with significant changes in the dynamics of the engine. The many issues of interfaces between new components and the engine can be better understood and be resolved prior to the firing of the engine. In this paper, the SSME real time simulation Lab at the MSFC, the SSME real time model, SSME engine and control system stability analysis, both in real time and non-real time is presented.

Kuo, F. Y.↗
NASA NTRS1972

An analysis of the booster plume impingement environment during the space shuttle nominal staging maneuver

An experimental study of the plume impingement heating on the space shuttle booster afterbody resulting from the space shuttle orbiter engine plumes was conducted. The 1/100-scale model tests consisted of one and two orbiter engine firings on a flat plate, a flat plate with a fin, and a cylinder model. The plume impingement heating rates on these surfaces were measured using thin film heat transfer gages. Results indicate the engine simulation is a reasonable approximation to the two engine configuration, but more tests are needed to verify the plume model of the main engine configuration. For impingment, results show models experienced laminar boundary layer convective heating. Therefore, tests at higher Reynolds numbers are needed to determine impingment heating.

Wojciechowski, C. J.↗
NASA NTRS1978

Orbiter/payload proximity operations SES Postsim report. Lateral approach and other techniques

Various approach and stationkeeping simulations (proximity operations) were conducted in the Shuttle engineering simulator (SES). This simulator is the first to dynamically include the Orbiter reaction control system (RCS) plume effects on a payload being recovered after rendezvous operations. A procedure for braking, using the simultaneous firing of both jets, was evaluated and found very useful for proximity operations. However this procedure is very inefficient in the RCS usage and requires modifications to the digital autopilot (DAP) software. A new final approach, the lateral approach technique (LAT), or the momentum vector proximity approach, was also evaluated in the simulations. The LAT, which included a tailfirst approach for braking, was evaluated successfully with both inertial and gravity stabilized payloads.

Olszewski, O.↗
NASA NTRS1992

Event-driven simulation in SELMON: An overview of EDSE

EDSE (event-driven simulation engine), a model-based event-driven simulator implemented for SELMON, a tool for sensor selection and anomaly detection in real-time monitoring is described. The simulator is used in conjunction with a causal model to predict future behavior of the model from observed data. The behavior of the causal model is interpreted as equivalent to the behavior of the physical system being modeled. An overview of the functionality of the simulator and the model-based event-driven simulation paradigm on which it is based is provided. Included are high-level descriptions of the following key properties: event consumption and event creation, iterative simulation, synchronization and filtering of monitoring data from the physical system. Finally, how EDSE stands with respect to the relevant open issues of discrete-event and model-based simulation is discussed.

Rouquette, Nicolas F.↗
NASA NTRS1961

Effects of Gyroscopic Cross Coupling Between Pitch and Yaw on the Handling Qualities of VTOL Aircraft

Gyroscopic cross coupling between pitch and yaw was simulated with a variable-stability helicopter while hovering in a yawing maneuver to ascertain the effect of cross coupling on handling qualities. Pilot ratings of the controllability of cross coupling were obtained for various combinations of longitudinal control power, angular velocity about the yaw axis, and simulated engine angular momentum. A theoretical investigation, supplemented by simulator data, was undertaken to determine the effect of longitudinal damping on the coupling controllability. Also, a comparison was made between flight and simulator data. The results indicated that for an aircraft with otherwise satisfactory longitudinal handling qualities, the level of cross coupling is satisfactory when less than 30 percent of the available longitudinal control will trim out the largest gyroscopic coupling moment which might be encountered. Increased longitudinal damping resulted in a significant increase in the controllability of pitch-yaw gyroscopic cross coupling.

Garren, John F., Jr.↗
NASA NTRS2010

Control Design for a Generic Commercial Aircraft Engine

This paper describes the control algorithms and control design process for a generic commercial aircraft engine simulation of a 40,000 lb thrust class, two spool, high bypass ratio turbofan engine. The aircraft engine is a complex nonlinear system designed to operate over an extreme range of environmental conditions, at temperatures from approximately -60 to 120+ F, and at altitudes from below sea level to 40,000 ft, posing multiple control design constraints. The objective of this paper is to provide the reader an overview of the control design process, design considerations, and justifications as to why the particular architecture and limits have been chosen. The controller architecture contains a gain-scheduled Proportional Integral controller along with logic to protect the aircraft engine from exceeding any limits. Simulation results illustrate that the closed loop system meets the Federal Aviation Administration s thrust response requirements

Csank, Jeffrey↗
NASA NTRS1981

Rub energetics of compressor blade tip seals

The rub mechanics of aircraft gas turbine engine compressor abradable blade tip seals was studied at simulated engine conditions. In 12 statistically planned, instrumented rub tests using single titanium blades and fiber-metal rubstrips the rub velocity, incursion rate, incursion depth, blade thickness, and abradable strength were varied to determine the effects on rub energy, heat split between the blade, rubstrip surface and rub debris, and blade and seal wear. The rub energies were found to be most significantly affected by the incursion rate while rub velocity and blade thickness were of secondary importance. In five additional rub tests using single nickel alloy blades and multiple titanium alloy blades, rub energy and wear effects were found to be similar for titanium and nickel alloy blades while rub energies increased for multiple blades relative to single blade test results.

Laverty, W. F.↗
NASA NTRS1992

Synchronization Of Parallel Discrete Event Simulations

Adaptive, parallel, discrete-event-simulation-synchronization algorithm, Breathing Time Buckets, developed in Synchronous Parallel Environment for Emulation and Discrete Event Simulation (SPEEDES) operating system. Algorithm allows parallel simulations to process events optimistically in fluctuating time cycles that naturally adapt while simulation in progress. Combines best of optimistic and conservative synchronization strategies while avoiding major disadvantages. Algorithm processes events optimistically in time cycles adapting while simulation in progress. Well suited for modeling communication networks, for large-scale war games, for simulated flights of aircraft, for simulations of computer equipment, for mathematical modeling, for interactive engineering simulations, and for depictions of flows of information.

Steinman, Jeffrey S.↗
NASA NTRS1993

Development and operation of a real-time simulation at the NASA Ames Vertical Motion Simulator

The Vertical Motion Simulator (VMS) facility at the NASA Ames Research Center combines the largest vertical motion capability in the world with a flexible real-time operating system allowing research to be conducted quickly and effectively. Due to the diverse nature of the aircraft simulated and the large number of simulations conducted annually, the challenge for the simulation engineer is to develop an accurate real-time simulation in a timely, efficient manner. The SimLab facility and the software tools necessary for an operating simulation will be discussed. Subsequent sections will describe the development process through operation of the simulation; this includes acceptance of the model, validation, integration and production phases.

Sweeney, Christopher↗
NASA NTRS1990

Reaction control system/remote manipulator system automation

The objectives of this project is to evaluate the capability of the Procedural Reasoning System (PRS) in a typical real-time space shuttle application and to assess its potential for use in the Space Station Freedom. PRS, developed by SRI International, is a result of research in automating the monitoring and control of spacecraft systems. The particular application selected for the present work is the automation of malfunction handling procedures for the Shuttle Remote Manipulator System (SRMS). The SRMS malfunction procedures will be encoded within the PRS framework, a crew interface appropriate to the RMS application will be developed, and the real-time data interface software developed. The resulting PRS will then be integrated with the high-fidelity On-orbit Simulation of the NASA Johnson Space Center's System Engineering Simulator, and tests under various SRMS fault scenarios will be conducted.

Hiers, Harry K.↗
NASA NTRS1999

National Cycle Program (NCP) Common Analysis Tool for Aeropropulsion

Through the NASA/Industry Cooperative Effort (NICE) agreement, NASA Lewis and industry partners are developing a new engine simulation, called the National Cycle Program (NCP), which is the initial framework of NPSS. NCP is the first phase toward achieving the goal of NPSS. This new software supports the aerothermodynamic system simulation process for the full life cycle of an engine. The National Cycle Program (NCP) was written following the Object Oriented Paradigm (C++, CORBA). The software development process used was also based on the Object Oriented paradigm. Software reviews, configuration management, test plans, requirements, design were all apart of the process used in developing NCP. Due to the many contributors to NCP, the stated software process was mandatory for building a common tool intended for use by so many organizations. The U.S. aircraft and airframe companies recognize NCP as the future industry standard for propulsion system modeling.

Follen, G.↗
NASA NTRS2003

Combustor Simulation

The goal was to perform 3D simulation of GE90 combustor, as part of full turbofan engine simulation. Requirements of high fidelity as well as fast turn-around time require massively parallel code. National Combustion Code (NCC) was chosen for this task as supports up to 999 processors and includes state-of-the-art combustion models. Also required is ability to take inlet conditions from compressor code and give exit conditions to turbine code.

Norris, Andrew↗
NASA NTRS2013

Adoption of Test Driven Development and Continuous Integration for the Development of the Trick Simulation Toolkit

This paper describes the adoption of a Test Driven Development approach and a Continuous Integration System in the development of the Trick Simulation Toolkit, a generic simulation development environment for creating high fidelity training and engineering simulations at the NASA/Johnson Space Center and many other NASA facilities. It describes what was learned and the significant benefits seen, such as fast, thorough, and clear test feedback every time code is checked-in to the code repository. It also describes a system that encourages development of code that is much more flexible, maintainable, and reliable. The Trick Simulation Toolkit development environment provides a common architecture for user-defined simulations. Trick builds executable simulations using user-supplied simulation-definition files (S_define) and user supplied "model code". For each Trick-based simulation, Trick automatically provides job scheduling, checkpoint / restore, data-recording, interactive variable manipulation (variable server), and an input-processor. Also included are tools for plotting recorded data and various other supporting tools and libraries. Trick is written in C/C++ and Java and supports both Linux and MacOSX. Prior to adopting this new development approach, Trick testing consisted primarily of running a few large simulations, with the hope that their complexity and scale would exercise most of Trick's code and expose any recently introduced bugs. Unsurprising, this approach yielded inconsistent results. It was obvious that a more systematic, thorough approach was required. After seeing examples of some Java-based projects that used the JUnit test framework, similar test frameworks for C and C++ were sought. Several were found, all clearly inspired by JUnit. Googletest, a freely available Open source testing framework, was selected as the most appropriate and capable. The new approach was implemented while rewriting the Trick memory management component, to eliminate a fundamental design flaw. The benefits became obvious almost immediately, not just in the correctness of the individual functions and classes but also in the correctness and flexibility being added to the overall design. Creating code to be testable, and testing as it was created resulted not only in better working code, but also in better-organized, flexible, and readable (i.e., articulate) code. This was, in essence the Test-driven development (TDD) methodology created by Kent Beck. Seeing the benefits of Test Driven Development, other Trick components were refactored to make them more testable and tests were designed and implemented for them.

Penn, John M.↗