Search NASA⌕ Search

SEARCH · Search NASA

Results for “external”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Efficient second harmonic generation of a diode-laser-pumped CW Nd:YAG laser using monolithic MgO:LiNbO3 external resonant cavities

56-percent efficient external-cavity-resonant second-harmonic generation of a diode-laser pumped, CW single-axial-mode Nd:YAG laser is reported. A theory of external doubling with a resonant fundamental is presented and compared to experimental results for three monolithic cavities of nonlinear MgO:LiNbO3. The best conversion efficiency was obtained with a 12.5-mm-long monolithic ring cavity doubler, which produced 29.7 mW of CW, single-axial model 532-nm radiation from an input of 52.5 mW.

Kozlovsky, William J.↗

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗

Remote measurement of ice thickness on the shuttle external tank surface

A passive technique is proposed for remote measurement of thickness of the ice layer formed on the external tank surface of the Shuttle during the T-2 hours period before launch. It is based on the comparison of the ratios of the intensities of three preselected near-IR wavelength bands scattered from the (test spot) and a neighboring (reference spot) on the tank surface. The Shuttle is uniformly illuminated by a battery of strategically located solar simulator lamps and banks of incadescent lamps during prelaunch period. Thus, there should be adequate radiation in the three selected bands incident on the external tank surface during the test period. It is planned to conduct a feasibility study of the proposed technique before recommending it to the KSC/SSC teams for adoption.

Singh, Jag J.↗

Analysis and design of optimized truncated scarfed nozzles subject to external flow effects

Rao's method for computing optimum thrust nozzles is modified to study the effects of external flow on the performance of a class of exhaust nozzles. Members of this class are termed scarfed nozzles. These are two-dimensional, nonsymmetric nozzles with a flat lower wall. The lower wall (the cowl) is truncated in order to save weight. Results from a parametric investigation are presented to show the effects of the external flowfield on performance.

Shyne, Rickey J.↗

The QBO and weak external forcing by solar activity: A three dimensional model study

A better understanding is attempted of the physical mechanisms leading to significant correlations between oscillations in the lower and middle stratosphere and solar variability associated with the sun's rotation. A global 3-d mechanistic model of the middle atmosphere is employed to investigate the effects of minor artificially induced perturbations. The aim is to explore the physical mechanisms of the dynamical response especially of the stratosphere to weak external forcing as it may result from UV flux changes due to solar rotation. First results of numerical experiments dealing about the external forcing of the middle atmosphere by solar activity were presented elsewhere. Different numerical studies regarding the excitation and propagation of weak perturbations have been continued since then. The model calculations presented are made to investigate the influence of the quasi-biennial oscillation (QBO) on the dynamical response of the middle atmosphere to weak perturbations by employing different initial wind fields which represent the west and east phase of the QBO.

Dameris, M.↗

Concept for a lunar He-3 transporter using an in-orbit modified shuttle external tank

A concept is presented for the transport of gaseous He-3 in temperature equilibrium with the liquid hydrogen and liquid oxygen in a modified lunar shuttle external tank. The concept first describes the internal modifications to accommodate He-3, and then, the external modifications to incorporate a propulsion system and an aerobrake. Estimates of the system masses and an assessment of propulsion requirements show the round trip capability. The concept also includes a description of the lunar orbit servicing and transfer operations.

Butterfield, A. J.↗

Single mode wavelength control of modulated AlGaAs lasers with external and internal etalon feedback

Single mode lasing without mode hops has been obtained for VSIS and CSP laser diodes with an external etalon attached to the laser's front facet for up to an 8 C range CW and a 4 C range pulsed, with .07 nm/C tuning. Tests of thin tapered-thickness (TTT) laser diodes show CW and pulsed single mode lasing over 10 C and 2 C ranges, respectively, with .08 nm/C tuning. An analysis of the TTT structure reveals the equivalent of an internal etalon. The time-resolved pulsed behavior for both types of lasers show single mode lasing within the proper temperature ranges with minor modes present only early in the optical pulse, if at all. The external etalon produces noticeable interference fringes in the farfield pattern, while those of the TTT lasers are smooth. Ongoing CW lifetest results indicate stability to within one longitudinal mode after a few hundred hours of operation, along with at least several thousand hours lifetime.

Maynard, William L.↗

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗

Computational results for the effects of external disturbances on transition location of bodies of revolution from subsonic to supersonic speeds and comparisons with experimental data

Computational experiments have been performed for a few configurations in order to investigate the effects of external flow disturbances on the extent of laminar flow and wake drag. Theoretical results have been compared with experimental data for the AEDC cone, for Mach numbers from subsonic to supersonic, and for both free flight and wind tunnel environments. The comparisons have been found to be very satisfactory, thus establishing the utility of the present method for the design and development of laminar flow configurations and for the assessment of wind tunnel data. In addition, results of calculations concerning the effects of unit Reynolds numbers on transition are presented. In addition to the AEDC cone, computations have been performed for an ogive body of revolution at zero angle of attack and supersonic Mach numbers. Results are presented for transition Reynolds number and wake drag for external disturbances corresponding to free air and the test section of the AEDC-VKF tunnel. These results have been found to compare quite well with wind tunnel data for cases when surface suction is applied as well as when suction is absent.

Goradia, S. H.↗

An active optimal control strategy of rotor vibrations using external forces

An active control strategy for lateral rotor vibrations using external forces is proposed. An extended state observer is used to reconstruct the full states and the unbalance distribution. An optimal controller which accommodates persistent unbalance excitation is derived with feedback of estimated states and unbalances. Numerical simulations were conducted for two separate four degree of freedom rotor systems. These simulations indicated that the proposed strategy can achieve almost complete vibration cancellation. This was shown to be true even when the number of external control forces was less than the system order so long as coordinate coupling was present. Both steady state and transient response at a constant speed are presented.

Zhu, W.↗

Analysis and design of optimized truncated scarfed nozzles subject to external flow effects

Rao's method for computing optimum thrust nozzles is modified to study the effects of external flow on the performance of a class of exhaust nozzles. Members of this class are termed scarfed nozzles. These are two-dimensional, nonsymmetric nozzles with a flat lower wall. The lower wall (the cowl) is truncated in order to save weight. Results from a parametric investigation are presented to show the effects of the external flowfield on performance.

Shyne, Rickey J.↗

Lyman alpha radiation in external galaxies

The Ly alpha line of atomic hydrogen is often a luminous component of the radiation emitted by distant galaxies. Except for those galaxies which have a substantial central source of non-stellar ionizing radiation, most of the Ly alpha radiation emitted by galaxies is generated within regions of the interstellar medium which are photoionized by starlight. Conversely, much of the energy radiated by photoionized regions is carried by the Ly alpha line. Only hot, massive stars are capable of ionizing hydrogen in the interstellar medium which surrounds them, and because such stars are necessarily short-lived, Ly alpha emission traces regions of active star formation. Researchers argue that the strength of the Ly alpha emission observed from external galaxies may be used to estimate quantitatively the dust content of the emitting region, while the Ly alpha line profile is sensitive to the presence of shock waves. Interstellar dust particles and shock waves are intimately associated with the process of star formation in two senses. First, both dust particles and shock waves owe their existence to stellar activity; second, they may both serve as agents which facilitate the formation of stars, shocks by triggering gravitational instabilities in the interstellar gas that they compress, and dust by shielding star-forming molecular clouds from the ionizing and dissociative effects of external UV radiation. By using Ly alpha observations as a probe of the dust content in diffuse gas at high redshift, we might hope to learn about the earliest epochs of star formation.

Neufeld, David A.↗

Sensitivity to the external temperature of some GPS time receivers

It has been assumed until recently that GPS time receiver units (recever+cables+antenna) have good stability and do not affect time transfer by more than 1 ns. Differences of a few nanoseconds sometimes observed during calibration campaigns have been attributed to external causes, such as multipath propagation, rather than to variations within the hardware. The characteristic feature of most comparisons of GPS time receivers is their short duration. Normally the comparison takes place, at most, over one week. To observe the behavior of GPS time receivers over a period of several months, an experiment has been organized involving three receivers of two types. All three were connected to the same atomic clock. An unexpected sensitivity to external temperature was found in one type of receiver. This effect proved to be a function of the length and type of the antenna cable. In the most unfavorable case the sensitivity was 1.8 ns/C.

Lewandowski, Wlodzimierz W.↗

Sensitivity analysis, approximate analysis, and design optimization for internal and external viscous flows

A gradient-based design optimization strategy for practical aerodynamic design applications is presented, which uses the 2D thin-layer Navier-Stokes equations. The strategy is based on the classic idea of constructing different modules for performing the major tasks such as function evaluation, function approximation and sensitivity analysis, mesh regeneration, and grid sensitivity analysis, all driven and controlled by a general-purpose design optimization program. The accuracy of aerodynamic shape sensitivity derivatives is validated on two viscous test problems: internal flow through a double-throat nozzle and external flow over a NACA 4-digit airfoil. A significant improvement in aerodynamic performance has been achieved in both cases. Particular attention is given to a consistent treatment of the boundary conditions in the calculation of the aerodynamic sensitivity derivatives for the classic problems of external flow over an isolated lifting airfoil on 'C' or 'O' meshes.

Taylor, Arthur C., III↗

Enhancements to the GRIDGEN structured grid generation system for internal and external flow applications

GRIDGEN is a government domain software package for interactive generation of multiple block grids around general configurations. Though it has been freely available since 1989, it has not been widely embraced by the internal flow community due to a misconception that it was designed for external flow use only. In reality GRIDGEN has always worked for internal flow applications, and GRIDGEN ongoing enhancements are increasing the quality of and efficiency with which grids for external and internal flow problems may be constructed. The software consists of four codes used to perform the four steps of the grid generation process. GRIDBLOCK is first used to decompose the flow domain into a collection of component blocks and then to establish interblock connections and flow solver boundary conditions. GRIDGEN2D is then used to generate surface grids on the outer shell of each component block. GRIDGEN3D generates grid points on the interior of each block, and finally GRIDVUE3D is used to inspect the resulting multiple block grid. Three of these codes (GRIDBLOCK, GRIDGEN2D, and GRIDVUE3D) are highly interactive and graphical in nature, and currently run on Silicon Graphics, Inc., and IBM RS/6000 workstations. The lone batch code (GRIDGEN3D) may be run on any of several Unix based platforms. Surface grid generation in GRIDGEN2D is being improved with the addition of higher order surface definitions (NURBS and parametric surfaces input in IGES format and bicubic surfaces input in PATRAN Neutral File format) and double precision mathematics. In addition, two types of automation have been added to GRIDGEN2D that reduce the learning curve slope for new users and eliminate work for experienced users. Volume grid generation using GRIDGEN3D has been improved via the addition of an advanced hybrid control function formulation that provides both orthogonality and clustering control at the block faces and clustering control on the block interior.

Steinbrenner, John P.↗

A millimeter-wave radiometer technique for measuring ice thickness on the surface of the Space Shuttle's external fueltank

The presence of ice on the outside surface of the external tanks of a Space Shuttle can be detrimental to the launch and it is important to detect its presence and measure its thickness. A description is given of the design of a millimeter-wave radiometer system developed for this purpose. The design is based on model calculations and measurements of the emission properties of an external tank panel, performed at 35, 94 and 140 GHz.

Ulaby, F. T.↗

Control of internal and external short circuits in lithium batteries using a composite thermal switch

A composite material has been developed, consisting of a blend of metal and fluorocarbon particles, which behaves as an electronic conductor at room temperature and which abruptly becomes an insulator at a predetermined temperature. This switching behavior results from the difference in thermal expansion coefficients between the conductive and non-conductive portions of the composite. This material was applied as a thin film between the carbon cathode in Li/SOCl2 cells, and the metallic cathode current collector. Using test articles incorporating this feature it was shown that lithium cells externally heated or internally heated during a short circuit lost rate capability and the ability to overheat well below the melting point of lithium (180 C). Thus, during an internal or external cell short circuit, the potential for thermal runaway involving reactions of molten lithium is avoided.

Mcdonald, Robert C.↗

An in-depth probabilistic study of external tank attach ring

This report deals with conducting a probabilistic study of the external tank attach ring (ETA) used as an interface between the external tank attach struts and the solid rocket booster. The ideas were to use probabilistic distributions for material, geometric, and load properties; to calculate probabilistic margins of safety; and then to compare results against the deterministic factors of safety that were used in the actual design process. The report describes how this was done and discusses some of the road blocks and data problems that were encountered during the study and provides some conclusions. A further refinement of this study is being considered for future work which would make more direct use of finite element analysis data coupled with Monte Carlo simulation. The basic conclusion herein indicates that the probabilistic margins of safety for the cases analyzed (by use of existing data) appear to support deterministic results and actually indicate higher reliabilities.

Pizzano, Frank↗