SEARCH · Search NASA

Results for “external surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Analyses of Transistor Punchthrough Failures

The failure of two transistors in the Altitude Switch Assembly for the Solid Rocket Booster followed by two additional failures a year later presented a challenge to failure analysts. These devices had successfully worked for many years on numerous missions. There was no history of failures with this type of device. Extensive checks of the test procedures gave no indication for a source of the cause. The devices were manufactured more than twenty years ago and failure information on this lot date code was not readily available. External visual exam, radiography, PEID, and leak testing were performed with nominal results Electrical testing indicated nearly identical base-emitter and base-collector characteristics (both forward and reverse) with a low resistance short emitter to collector. These characteristics are indicative of a classic failure mechanism called punchthrough. In failure analysis punchthrough refers to an condition where a relatively low voltage pulse causes the device to conduct very hard producing localized areas of thermal runaway or "hot spots". At one or more of these hot spots, the excessive currents melt the silicon. Heavily doped emitter material diffuses through the base region to the collector forming a diffusion pipe shorting the emitter to base to collector. Upon cooling, an alloy junction forms between the pipe and the base region. Generally, the hot spot (punch-through site) is under the bond and no surface artifact is visible. The devices were delidded and the internal structures were examined microscopically. The gold emitter lead was melted on one device, but others had anomalies in the metallization around the in-tact emitter bonds. The SEM examination confirmed some anomalies to be cosmetic defects while other anomalies were artifacts of the punchthrough site. Subsequent to these analyses, the contractor determined that some irregular testing procedures occurred at the time of the failures heretofore unreported. These testing irregularities involved the use of a breakout box and were the likely cause of the failures. There was no evidence to suggest a generic failure mechanism was responsible for the failure of these transistors.

Nicolas, David P.↗

NASA NTRS1996

Application of pneumatic lift and control surface technology to advanced transport aircraft

The application of pneumatic (blown) aerodynamic technology to both the lifting and the control surfaces of advanced transport aircraft can provide revolutionary changes in the performance and operation of these vehicles, ranging in speed regime from Advanced Subsonic Transports to the High Speed Civil Transport, and beyond. This technology, much of it based on the Circulation Control Wing blown concepts, can provide aerodynamic force augmentations of 80 to 100 (i.e., return of 80-100 pounds of force per pound of input momentum from the blowing jet). This can be achieved without use of external mechanical surfaces. Clever application of this technology can provide no-moving-part lifting surfaces (wings/tails) integrated into the control system to greatly simplify aircraft designs while improving their aerodynamic performance. Lift/drag ratio may be pneumatically tailored to fit the current phase of the flight, and takeoff/landing performance can be greatly improved by reducing ground roll distances and liftoff/touchdown speeds. Alternatively, great increases in liftoff weights and payloads are possible, as are great reductions in wing and tail planform size, resulting in optimized cruise wing designs. Furthermore, lift generation independent of angle of attack provides much promise for increased safety of flight in the severe updrafts/downdrafts of microbursts and windshears, which is further augmented by the ability to sustain flight at greatly reduced airspeeds. Load-tailored blown wings can also reduce tip vorticity during highlift operations and the resulting vortex wake hazards near terminal areas. Reduced noise may also be possible as these jets can be made to operate at low pressures. The planned presentation will support the above statements through discussions of recent experimental and numerical (CFD) research and development of these advanced blown aerodynamic surfaces, portions of which have been conducted for NASA. Also to be presented will be predicted performance of advanced transports resulting from these devices. Suggestions will be presented for additional innovative high-payoff research leading to further confirmation of these concepts and their application to advanced efficient commercial transport aircraft.

Englar, Robert J.↗

DOE OSTI2020

A Bottom-up Approach to Improve the Representation of Deep Convective Clouds in Weather and Climate Models (Final Report)

A fundamental yet outstanding question about deep cumulus convection regards how convective updrafts, downdrafts, and surface-based cold pools are inter-related within organized storms, and how these three convective components are modulated by external and internal factors. We considered this question through numerical model simulations as well as data collected during the MC3E field campaign. One of our basic hypotheses was that deep cold pools are forced by wide downdrafts which arise from wide updrafts. This “bottom-up” perspective required consideration of the external controls on updraft width, and then the internal controls on cold-pool characteristics including depth. Model experiments showed that environmental vertical wind shear (an external factor) exerts a particularly strong control on updraft width; analyses of linear and nonlinear dynamic pressure forcing readily explain this control. The experiments also showed that increases in updraft width are accompanied by corresponding increases in downdraft width and cold-pool depth. The updraft–downdraft connection is through precipitation: the wide area of precipitation that will be initiated in a wide updraft will in turn lead to a wide downdraft. The downdraft–cold pool connection is through mass continuity: at the downdraft terminus, the large downdraft mass flux through a wide downdraft must lead to a deep cold pool. Model experiments also showed that the cold-pool depth and other characteristics can be significantly modulated by microphysical processes (internal factors). Specifically, the cold-pool expansion rate, depth, and intensity was found to depend most strongly on the amount of rain evaporation near the ground. However, the sustenance of the cold pool itself depended upon the downdrafts strengthened by sublimation of graupel higher in the storm. Finally, field campaign data revealed compelling inter-relationships between the cold-pool characteristics, and downdraft transience in terms of the microphysics. For example, pulses of hail and graupel (also internal factors) within downdrafts resulted in short-lived increases in the cold-pool depth. However, the cold-pool speed appeared to be relatively independent of the cold-pool depth and intensity, suggesting limitations of density current theory to convective cold pools in nature.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1989

Advanced high-temperature batteries

The promise of very high specific energy and power was not yet achieved for practical battery systems. Some recent approaches are discussed for new approaches to achieving high performance for lithium/DeS2 cells and sodium/metal chloride cells. The main problems for the development of successful LiAl/FeS2 cells were the instability of the FeS2 electrode, which has resulted in rapidly declining capacity, the lack of an internal mechanism for accommodating overcharge of a cell, thus requiring the use of external charge control on each individual cell, and the lack of a suitable current collector for the positive electrode other than expensive molybdenum sheet material. Much progress was made in solving the first two problems. Reduction of the operating temperatures to 400 C by a change in electrolyte composition has increased the expected life to 1000 cycles. Also, a lithium shuttle mechanism was demonstrated for selected electrode compositions that permits sufficient overcharge tolerance to adjust for the normally expected cell-to-cell deviation in coulombic efficiency. Sodium/sulfur batteries and sodium/metal chloride batteries have demonstrated good reliability and long cycle life. For applications where very high power is desired, new electrolyte coinfigurations would be required. Design work was carried out for the sodium/metal chloride battery that demonstrates the feasibility of achieving high specific energy and high power for large battery cells having thin-walled high-surface area electrolytes.

Nelson, Paul A.↗

DOE OSTI2020

Review of heat transfer enhancement techniques for single phase flows

The thermal energy exchange between a flowing fluid and its confining channel is a ubiquitous process in modern society. To enhance the fluid-to-wall or wall-to-fluid heat transfer, several techniques have been developed to maximize the contact area between the fluid and the inner wall and/or disrupt the flow to enhance circulation or induce turbulence. Deployment of channels having features capable of enhancing heat transfer enables the reduction of heat exchanger size while maintaining performance. Reduction in equipment size is critical due to the ability to minimize the required volume of costly working fluids and to mitigate potential safety concerns associated with total system fluid volume. Here, a comprehensive review of single-phase heat transfer enhancement techniques is presented. The article provides a thorough comparison by analyzing the heat transfer rate, pressure drop, and other operational aspects. Single-phase heat transfer enhancement methods are divided into active and passive techniques. Active methods such as electrohydrodynamic (EHD), magnetohydrodynamics (MHD), or mechanical motion require external power to create enhancement. Passive methods such as dimples, fins, or tape inserts do not require external input and rely only on surface modification. Although active methods are more expensive and difficult to implement compared to passive techniques, it enables active control of heat transfer augmentation. Finally, this review develops and summarizes key learning data for design optimization enabled by additive manufacturing and machine learning algorithms, helping to inform these next-generation heat exchanger design methodologies for a plethora of modern applications such as electrification of vehicles, computing, and classical industries.

42 ENGINEERING↗

NASA NTRS2001

Seismoball: A Small Europa Orbiter Drop-Off Probe for Early Exploration of the Europan Surface

Recent magnetometry data received from Galileo indicate that the most likely explanation for the magnetic signature there is indeed a global conducting layer below the surface. This conducting layer is well matched by a salty, mineral rich strata beneath the Europan ice crust or a salt water ocean. Galileo imaging results show a variety of terrain types thought to contain young material; for example, lineaments, chaotic terrain, and eruption features. Additionally, Galileo images have shown indications of areas of up-welling where subsurface material periodically gets pushed to the surface due to the forces of fracturing, butting, and refreezing of the ice sheet. While Europa Orbiter will provide close-flyby high resolution images, as well as magnetometry, spectroscopy and other remote sensing data of the surface, it will not be able to provide essential engineering data like surface hardness and surface ice structure needed to support eventual landed missions. Additionally, ice chemical composition at microscopic scales can only be studied in detail through in situ instrumentation. Seismoball is a small probe designed to be injected into a surface intersect orbit around Europa. Using small reverse thrusters, the probe will be capable of nulling the high horizontal injection velocity as it approaches the 2 km surface injection altitude, thus allowing it to fall to the surface at an impact velocity of < 100m/sec (much less than the DS-2 impact velocities). The external breakaway thruster structure and crushable exterior shell absorb the impact energy while allowing the science instrument suite to remain intact. JPL has already started analyzing the entry dynamics and designing/building a small, low mass probe which will withstand the impact g-forces and fit as a 'carry-on' on board the Europa Orbiter. The probe will carry a suite of 5-6 micro-instruments for imaging the surface (both microscopic and far-field), surface and shallow subsurface ice temperatures, surface hardness, crustal dynamics and periodicity, and compositional chemistry. If selected, this flight development activity will provide a unique science opportunity and adjunct to the primary Orbiter science mission. The final flight system will be designed to accommodate orbiter mass, volume, and power interface constraints, as well as entry dynamics, g-load mitigation, and arbitrary landing orientation.

Tamppari, L.↗

NASA NTRS2022

FY22 X-Hab: Colorado School of Mines: Planetary Resource & In-Situ Material Habitat Outfitting for Space Exploration (PRISM-HOUSE)

The Colorado School of Mines (CSM) was awarded a project under the Moon to Mars eXploration Systems and Habitation (M2M X-Hab) Academic Innovation Challenge on June 10, 2021 for the proposed Planetary Resource & In-Situ Material Habitat Outfitting for Space Exploration (PRISM-HOUSE) lunar habitat system. The project deliverables have been executed concurrently with coursework in the CSM Space Resources program, specifically for the Space Resources Project I & II classes. A team was established in the fall semester of 2021 and a Systems Engineering process was followed to brainstorm initial concepts, determine objectives, flow down top-level requirements, and identify areas for which the project could best further the understanding of the overall system through targeted detailed design and design evaluation testing. This report summarizes the overall project, as well as specific work completed in the spring semester of 2022. PRISM-HOUSE is a lunar habitat system that is deployed on the lunar surface robotically and supports safe, long-term human occupancy while maximizing the use of in-situ resources and minimizing the mass of supplies and equipment that must be delivered from Earth. In this report, the team provides an overview and description of the objectives, the system, and how the current design was selected from various alternatives, as well as the resulting products of systems engineering tasks such as product and specification trees and flow-down requirements. A review of current risks and planned mitigation are reviewed. Four key PRISM-HOUSE systems are explored: the inflatable Habitat, External Structures & Environmental Protection (ESEP), Human Interior Goods (HIG), and ECLSS & Remote Outfitting (E&RO); for each, the team provides a detailed system description and an overview of analyses performed supporting final design, followed by a review of each Design Evaluation Test (DET) performed and resulting conclusions. The report closes with a suggestion of next steps.

Peter Corwin↗

NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

While oxygen will probably be the first fluid liquefied from in-situ developed propellants, hydrogen will also be a sought-after commodity on both the Lunar and Martian surfaces. General hydrogen liquefaction processes are not significantly affected by the atmosphere on Mars and similar processes can be applied on both surfaces. However, hydrogen will require different processes than oxygen (which can be directly liquefied into its final use tank) due to the different spin states the hydrogen nucleus (i.e. parahydrogen and orthohydrogen) can have as well as the significant sensible energy that has to be removed prior to the actual phase change. Due to the low efficiency of 20 K class cryocoolers and high sensible heat removal requirements at higher temperatures, significant benefits can be obtained by precooling the hydrogen gas in a variety of manners. The benefits of three concepts are explored to take advantage of different precooling technics as well as accounting for sensible, latent, and para to ortho conversion heating requirements. Process concepts are shown that can reduce the base input power requirements for heat removal by more than 67% and the radiator area by similar amounts. A majority of the technology development for these processes has already begun, both within NASA and externally, with the few gaps being identified.

ISRU↗

NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

ISRU↗

DOE OSTI2025

UV + Damp Heat Induced Power Losses in Fielded Utility N-Type Si PV Modules

A recent trend in commercial PV modules is a transition to n-type silicon cells, including passivated emitter rear totally diffused (n-PERT), tunnel oxide passivated contact (TOPCon), and silicon heterojunction (SHJ). There is evidence via lab studies that some of these cells are more susceptible to UV induced degradation (UVID), yet there is a lack of confirmation that such degradation occurs in the field. Current IEC standards designed to screen for early module failures require only minimal UV exposure (15 kWh/m2 280-400 nm, ~2-3 months equivalent outdoor exposure). Here, we investigate fielded n-PERT silicon (Si) modules from a commercial utility that show power losses of ~2%/year. We present a comprehensive picture of the physics and chemistry of degradation supported by both module and cell electronic characterization (EL, PL, IV, EQE, and DLIT) and materials-level morphological and chemical analysis (SEM, EDS, XPS, FTIR, and HPLC). All sampled site modules show short circuit current (Isc) and open circuit voltage (Voc) losses when compared to unfielded spares, with the most severely degraded also having losses in fill factor (FF). We identify two different degradation modes contributing to overall power loss: (1) external quantum efficiency (EQE) measurements show losses in the blue range of the spectra, indicative of cell surface recombination losses, and (2) variations in high series resistance (Rs) at the cell level that are correlated with compositional differences in cell metallization. Using unfielded spares, we were able to reproduce Voc, Isc, and EQE losses via a minimum UV stress of 67.5 kWh/m2 (280-400 nm), 4.5x the exposure currently required in IEC 61215-2 (MQT 10). Degradation continued with additional UV dosage equivalent to the fielded modules (405 kWh/m2 total), with power loss leveling out at an average of 6.1%. Subsequent 1000 h of 85% RH/85degrees C damp heat testing showed that cells exposed to UV underwent additional severe series resistance degradation, even those without the susceptible paste composition seen in the field, whereas non-UV exposed cells saw little change. We attribute this to higher concentrations of acetic acid generated on the UV exposed area of the module, leading to degradation of the gridline/cell interface and high Rs. This study is unique in that it reproduces field observed utility scale UVID with an accelerated test and supports the need for standards development for longer UV exposure combined with other stress factors to catch materials interplay within a module package.

14 SOLAR ENERGY↗

NASA NTRS2001

Bridgman Growth of Detached GeSi Crystals

The growth of detached crystals by the Bridgman technique, in which the growing crystal is not in contact with the crucible wall, has been observed both on earth and in microgravity conditions. Such detachment has particularly been in evidence in microgravity experiments, where the pressure head of the molten sample is absent. At present, the mechanisms contributing to the detachment are not completely understood and until recently detachment has not been reproducibly obtained. Key parameters which must be considered are the contact angle between the melt and the crucible and the growth angle. Another essential parameter is the pressure difference between the annular gap around the solid below the melt and the volume above the melt. Here we present results of the growth of Ge(0.98)Si(0.02) using adjustments in the applied temperature profile to control the pressure difference between the bottom and top of the melt. The technique is less susceptible to sample contamination than controlling the pressure by connecting the crucible to external gas sources. Using this technique, a pressure difference is created by decreasing the temperature in the volume above the melt while the sample is molten but prior to growth. A maximum pressure difference approximately equal to the pressure head of the molten sample can thus be obtained. Several GeSi crystals were grown in pyrolitic boron nitride crucibles. When a pressure difference was applied, samples were reproducibly grown mostly detached. For comparison, samples were also grown in a configuration in which gas could pass freely between the gap below the melt and the volume above the melt and no pressure difference could be established. These samples were initially attached. Existence of detachment was determined both by measuring the radius of the samples with a profilometer and by observations of the sample surfaces with optical and electron microscopy. The gap thickness between the crucible and detached crystal was on the order of 10 micron. The surfaces of the attached areas of the crystals had the same shape as the interior crucible wall whereas in the detached areas the crystal facets could usually be observed.

Volz, M. P.↗

NASA NTRS2002

NASA Tech Briefs, April 2002

The contents include: 1) Application Briefs; 2) Sneak Preview of Sensors Expo; 3) The Complexity of the Diagnosis Problem; 4) Design Concepts for the ISS TransHab Module; 5) Characteristics of Supercritical Transitional Mixing Layers; 6) Electrometer for Triboelectric Evaluation of Materials; 7) Infrared CO2 Sensor With Built-In Calibration Chambers; 8) Solid-State Potentiometric CO Sensor; 9) Planetary Rover Absolute Heading Detection Using a Sun Sensor; 10) Concept for Utilizing Full Areas of STJ Photodetector Arrays; 11) Development of Cognitive Sensors; 12) Enabling Higher-Voltage Operation of SOl CMOS Transistors; 13) Estimating Antenna-Pointing Errors From Beam Squints; 14) Advanced-Fatigue-Crack-Growth and Fracture- Mechanics Program; 15) Software for Sequencing Spacecraft Actions; 16) Program Distributes and Tracks Organizational Memoranda; 16) Flat Membrane Device for Dehumidification of Air; 17) Inverted Hindle Mount Reduces Sag of a Large, Precise Mirror; 18) Heart-Pump-Outlet/Cannula Coupling; 19) Externally Triggered Microcapsules Release Drugs In Situ; 20) Combinatorial Drug Design Augmented by Information Theory; 21) Multiple-Path-Length Optical Absorbance Cell; 22) Model of a Fluidized Bed Containing a Mixture of Particles; 23) Refractive Secondary Concentrators for Solar Thermal Systems; 24) Cold Flow Calorimeter; 25) Methodology for Tracking Hazards and Predicting Failures; 26) Estimating Heterodyne-Interferometer Polarization Leakage; 27) An Efficient Algorithm for Propagation of Temporal- Constraint Networks; 28) Software for Continuous Replanning During Execution; 29) Surface-Launched Explorers for Reconnaissance/Scouting; 30) Firmware for a Small Motion-Control Processor; 31) Gear Bearings and Gear-Bearing Transmissions; and 32) Linear Dynamometer With Variable Stroke and Frequency.

Source record↗

NASA NTRSDate not supplied

Additive Manufacturing (AM) for Propulsion Component and System Applications

NASA MSFC is developing several areas of additive manufacturing (AM) for propulsion component and system applications. These developments include new AM process and material development, large-scale AM pathfinder component fabrication and hot-fire testing, AM-centric design methodology, modeling and simulation, post-processing advancements, and new design applications of AM in aerospace. Some specific areas NASA has focused is the development and commercial infusion of AM supply chain for materials such as copper-alloy GRCop (Cu-Cr-Nb), Hydrogen-resistant alloys (NASA HR-1, JBK-75), refractory-based alloys (C-103, W, Mo, new formulations), and bimetallic and multi-metallic AM processes. Additional efforts have been focused on large scale AM demonstrating complex thin-wall structures up to 60” diameter using directed energy deposition. Material characterization, properties and component hot-fire testing has been completed using many of these newly developed AM alloys/processes. NASA has also focused on improvements to post-processing including powder removal, surface enhancements, and support removal to further realize cost and schedule benefits to the overall supply chain. These developments are part of the NASA Rapid Analysis and Manufacturing Propulsion Technology (RAMPT), Low Cost Upper Stage Propulsion (LCUSP) and Long Life Additive Manufacturing (LLAMA) projects, in addition to internal IRAD, and external collaborations.

Additive Manufacturing↗

NASA NTRS2001

Health Monitoring Technology for Thermal Protection Systems on Reusable Hypersonic Vehicles

Integrated subsystem health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles (RLVs) in order to reduce life cycle costs, to increase safety margins, and to improve mission reliability. This talk summarizes a joint effort between NASA Ames and industry partners to develop rapid non-contact diagnostic tools for health and performance monitoring of thermal protection systems (TPS) on future RLVs. The specific goals for TPS health monitoring are to increase the speed and reliability of TPS inspections for improved operability at lower cost. The technology being developed includes a 3-D laser scanner for examining the exterior surface of the TPS, and a subsurface microsensor suite for monitoring the health and performance of the TPS. The sensor suite consists of passive overlimit sensors and sensors for continuous parameter monitoring in flight. The sensors are integrated with radio-frequency identification (RFID) microchips to enable wireless communication of-the sensor data to an external reader that may be a hand-held scanner or a large portal. Prototypes of the laser system and both types of subsurface sensors have been developed. The laser scanner was tested on Shuttle Orbiter Columbia and was able to dimension surface chips and holes on a variety of TPS materials. The temperature-overlimit microsensor has a diameter under 0.05 inch (suitable for placement in gaps between ceramic TPS tiles) and can withstand 700 F for 15 minutes.

Milos, Frank S.↗

NASA NTRS1994

Ultraviolet illuminated molecular cloud boundaries: Extended (C II) 158 micrometer emission toward L1630

The construction of a large scale map of the 158 micrometer C+ line toward the L1630/Orion B molecular cloud, covering an approximately 35' by 45' area which includes the NGC 2024 H II region, zeta-Ori, the reflection nebula NGC 2023, and the Horsehead nebula, is reported. Emission in the C II line is very widespread. The line was detected at levels in excess of a few 0.0001 erg/sq cm/s/sr over almost the entire mapped region. Extended emission associated with the NGC 2024 H II region and its envelope accounts for more than half of the C II flux. Over this approximately 1.5 by 2.5 pc region, the amount of gas phase carbon in the form of C+ is comparable to the amount of carbon in CO. This result, together with the C II distribution implies that C II emission arises on the surface of clumps throughout the cloud rather than in a single layer at the H II region boundary. Away from the H II region, most of the C II emission comes from the western edge of the L1630 cloud and probably results from excitation by external OB stars. The overall extent of the C II emission is comparable to that of millimeter molecular lines but the distributions are different in detail. The difference in C II and molecular line distributions, in particular, the larger extent of the C II emission west of NGC 2024 implies large variations in the ratio of the C II and J = 1 towards 0 intensities. Models of photon dominated regions can explain the relation between C II and CO intensities only if the cloud edges and cloud interior are considered separately. A method for using C II and radio continuum emission to characterize the relationship between OB stars and photon dominated regions is proposed.

Jaffe, D. T.↗

NASA NTRS1994

Ultraviolet-illuminated molecular cloud boundaries: Extended (C II) 158 micron emission toward L1630

We have made a large-scale map of the 158 micrometers C(+) line toward the L1630/Orion B molecular cloud. The map covers a approximately 35 min x 45 min area which includes the NGC 2024 H II region, zeta Ori, the reflection nebula NGC 2023, and the Horsehead nebula. Emission in the (C II) line is very widespread. The line was detected at levels in excess of a few 10(exp -4) ergs/sq cm/s/sr over almost the entire mapped region. Extended emission associated with the NGC 2024 H II region and its envelope accounts for more than half of the (C II) flux. Over this approximately 1.5 x 2.5 pc region, the amount of gas-phase carbon in the form of C(+) is comparable to the amount of carbon in CO. This result, together with the (C II) distribution, implies that (C II) emission arises on the surfaces of clumps throughout the cloud rather than in a single layer at the H II region boundary. Away from the H II region, most of the (C II) emission comes from the western edge of the L1630 cloud and probably results from excitation by external OB stars. The overall extent of the (C II) emission is comparable to that of millimeter molecular lines, but the distributions are different in detail. The difference in (C II) and molecular line distributions, in particular, the larger extent of the (C II) emission west of NGC 2024 implies large variations in the radio of the (C II) and CO J = 1 goes to 0 intensities. Models of photon-dominated regions can explain the relation between (C II) and CO intensities only if one considers the cloud edges and cloud interior separately. We propose a method for using (C II) and radio continuum emission to characterize the relationship between OB stars and photon-dominated regions.

Jaffe, D. T.↗

DOE OSTI2020

Custom NEON AOP reflectance mosaics and maps of shade masks, canopy water content

This mosaic of visible to shortwave infrared (VSWIR) data was derived from the assignable asset NEON AOP radiance data that was collected by LBNL’s Watershed Function SFA during the summer of 2018 (DOI: 10.15485/1617204). This atmospheric correction was completed to take into account site-specific terrain variability in the 334 km2 survey area centered around Crested Butte, CO. The atmospheric correction was completed using ACORN atmospheric correction software executed on 200 x 200 pixel kernels rather than line by line in order to capture local flight altitude conditions. Manual cloud delineation removed any small shaded areas that occurred within the data collection areas. Mosaics were developed based on preference for days that were in close timing proximity to the coincident ground campaign and with mosaicing criteria that minimized the angle between the sun and the sensor to retrieve the most consistent reflectance (min_phase_refl_tiled). Finally, we generated shade masks based on the geometry between the sun angle at time of flight, the ground surface, and the sensor. Here we provide the orthomosaiced estimated reflectance data (min_phase_refl_tiled.tif), canopy water content (wtrl), estimated atmospheric water vapor (wtrv), the observational data (obs) for this particular mosaic, the estimated visibility (vis), shade masks derived from the digital surface elevation model (shade) and the digital terrain model (shade_tch) added to the canopy height model (DOI: 10.15485/1617203), and a wavelength metadata file. Each image file is provided as a GeoTiff with internal tiling and LZW compression. These data can also be found on Google Earth Engine for extraction, download, and analysis of smaller extents (Google Earth Engine data is linked in external link table).

2018 NEON and 2025 CHESS Campaigns↗

NASA NTRS2024

Tracing Presolar Grain Populations Through Matrix Alteration Histories

Primitive meteorites preserve remnants of evolved stars as presolar grains, from asymptotic and red giant branch stars, novae and supernovae. These grains retain records of the formation mechanisms of the stellar environment from which they condensed, as well as physical and chemical processes in the interstellar medium (ISM), solar nebula and the parent bodies in which they are found. Consequently, their study can refine our understanding of the solar system and external stellar and planetary systems. However, presolar grains and their records can be altered, re-equilibrated with the surrounding matrix, and eventually lost through aqueous and thermal processing on the meteorite parent body. NanoSIMS is the most rapid and effective method for in situ identification of presolar grains via their highly anomalous isotopic ratios. Previous studies have measured variations in presolar grain populations between different matrix regions within the same meteorite thin section. However, most of these studies do not identify if there are any ties between these variations in presolar grain populations and the chemical and mineralogical differences in measured matrix regions. Therefore, the goal of this study is to determine if there is measurable variations in the degree of alteration of different matrix regions within the same thin section, and if mineralogical and chemical changes in matrix regions can be used as indicators for presolar grain preservation. Such a correlation could improve the efficiency of presolar grain identification during searches across large surface areas. To do this, we carried out coordinated scanning electron microscope (SEM) and NanoSIMS analyses, using a new SEM method which measures the ppm concentration of 100 nm to 5 μm sized Mg-, S-, Al-, C- and Ca-rich matrix grains.

presolar grains↗