SEARCH · Search NASA

Results for “fans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1978

VSTOL tilt nacelle aerodynamics and its relation to fan blade stresses

A scale model of a VSTOL tilt nacelle with a 0.508 m single stage fan was tested in the NASA Lewis 9x15 Low Speed Wind Tunnel to ascertain inlet aerodynamic and fan aeromechanical performance over the low speed flight envelope. Fan blade stress maxima occurred at discrete rotational speeds corresponding to integral engine order vibrations of the first flatwise bending mode. Increased fan blade stress levels coincided with internal boundary layer separation occurring but became severe only when the separation location had progressed to the entry lip region of the inlet. The inlet/fan system could operate within the low speed flight envelope without incurring fan blade stress limits although boundary layer separation did occur for certain operating conditions.

Shaw, R. J.↗

NASA NTRS1979

Effect of forward velocity and crosswind on the reverse-thrust performance of a variable-pitch fan engine

Variable-pitch-fan engines may be attractive for future short-haul aircraft if sufficient reverse thrust is available for aircraft deceleration after touchdown. Thrust reversal is obtained in these engines by changing fan blade pitch about 90 deg, which causes the fan airflow to enter the fan duct nozzle and exhaust through the fan inlet. This capability would eliminate the heavy and costly thrust reverser system required for current fixed-pitch turbofan engines. NASA has, therefore, supported the development of advanced technology for a quiet, clean, high-bypass-ratio turbofan engine for future short-haul aircraft. In connection with this program, tests were conducted to determine the effect of forward velocity and angle of attack on steady-state reverse-thrust performance. Other objectives of the tests were related to the determination of the effect of forward velocity on forward-to-reverse thrust transient performance and the determination of the effectiveness of an overshoot blade angle technique to establish reverse thrust during a transient. The results of the tests are discussed.

Reemsnyder, D. C.↗

NASA NTRS1978

Prop-fan propulsion - Its status and potential

Studies have established that advanced turboprop (prop-fan) equipped aircraft will reduce fuel consumption by 15 to 30 percent compared to aircraft equipped with high-bypass turbofan engines of equivalent technology. A reduction in direct operating costs of approximately 10 percent has been identified for commercial aircraft as well as approximately 20 percent lower gross weight airplane for long endurance military missions. The prop-fan propulsion system is being investigated as part of the NASA Aircraft Energy Efficiency program which includes both analytical studies and experimental tests. The experimental work encompasses performance and acoustic wind tunnel tests on several prop-fan models. The prop-fan technology status is reviewed in the major areas of performance, installed effects, cabin noise, blade structure and maintenance cost. Also, further activities required to complete the technical validation of prop-fans are described.

Dugan, J. F., Jr.↗

NASA NTRS1979

The effect of throttling on forward radiated fan noise

A study was undertaken to evaluate the effect of operating line throttling on inlet-arc noise from high speed fans. Experimental measurements on a 1/4-scale fan stage tested in an anechoic chamber, with and without inlet turbulence control devices, were utilized to assess the effect of constant speed throttling on the forward arc radiated noise characteristics. Different effects were observed in different speed ranges with different types of inflow turbulence control. These effects were correlated with some of the current theories on fan noise generation mechanisms, and partial success was achieved in attempting to relate the various theoretical models to the observed trends. The results of this study have an important bearing on estimating the noise characteristics of new fan designs from scaling the measured characteristics of previously tested fans.

Gliebe, P. R.↗

NASA NTRS1980

Acoustic pressures on a prop-fan aircraft fuselage surface

Acoustic pressure amplitude and phase distributions on the surface of a simulated fuselage (a rigid semi-cylinder) installed in an acoustically treated wind tunnel near a Prop-Fan model were measured. The test conditions simulated the relative tip Mach number and blade loading of a full scale Prop-Fan at high altitude 0.8 Mach number cruise. Measurements were also made at equivalent microphone locations without the semi-cylinder to establish the effects of the presence of a fuselage on the sound pressure amplitudes. These effects were found to be 6 dB at 90 degrees incidence, decreasing to no effect at grazing incidence. Comparison of measurements and calculations using a Hamilton Standard Prop-Fan noise calculation computer program showed good agreement in peak level and in phase distribution. Continuous recordings were also made of a Prop-Fan RPM sweep at constant simulated flight speed and a simulated flight speed sweep at constant Prop-Fan RPM. These showed smooth variations in noise level over the tip Mach number range 0.878 to 1.143.

Magliozzi, B.↗

NASA NTRS1980

CF6 fan performance improvement

A significant portion of the NASA-sponsored Performance Improvement Program for the CF6 engine was the development of an improved fan concept. This involved aerodynamic redesign of the CF6 fan blade to increase fan efficiency while retaining the mechanical integrity, operability, and acoustic characteristics of the existing blade. A further improvement in performance was obtained by adding a fan case stiffener ring to decouple blade-case vibrational characteristics, permitting a significant reduction in running tip clearance. Engine testing was performed to establish the performance, mechanical and acoustic properties of the new design relative to the current fan, and to establish power management characteristics for the CF6-50C2/E2 engine. A significant improvement in cruise power SFC of 1.8 percent was demonstrated in Sea Level testing projected to altitude flight conditions.

Patt, R. F.↗

NASA NTRS1981

The supersonic fan engine - An advanced concept in supersonic cruise propulsion

Engine performance and mission studies were conducted for a novel turbofan engine concept incorporating a supersonic through-flow fan, and comparisons were made with two supersonic transport (SST) engine concepts of equivalent thrust and technological sophistication. It was found that in the case of an SST with a cruise speed of Mach 2.32, the through-flow fan engine may yield ranges 10 to 20% greater than the two alternatives considered. The engine has a conventional core, with the supersonic fan being driven by a concentric low-pressure turbine that is uncoupled with the single, high pressure turbine/compressor core spool. Among the topics discussed are the methods of analysis employed and perturbation studies concerning supersonic fan adiabatic efficiency, fan discharge characteristics and propulsion system weight.

Franciscus, L. C.↗

NASA NTRS1983

Inlet-fan flow field computation

The flow field of a tilt-nacelle inlet-fan combination used for V/STOL aircraft is studied. Under certain flight conditions the inlet is subjected to high angles of attack and/or yaw. This produces a non-uniform or distorted flow field at the fan-face that can lead to large blade stresses. This paper presents an analytical approach to the coupled inlet-fan problem. The nacelle is modelled by a distribution of source panels and the fan by a distribution of radial vortices. A modified actuator disc with losses and a quasi-steady rotor response is used to derive the boundary condition at the fan-face. An example of the calculation is shown.

Matwey, M. D.↗

NASA NTRS1983

V/STOL model fan stage rig design report

A model single-stage fan with variable inlet guide vanes (VIGV) was designed to demonstrate efficient point operation while providing flow and pressure ratio modulation capability required for a V/STOL propulsion system. The fan stage incorporates a split-flap VIGV with an independently actuated ID flap to permit independent modulation of fan and core engine airstreams, a flow splitter integrally designed into the blade and vanes to completely segregate fan and core airstreams in order to maximize core stream supercharging for V/STOL operation, and an EGV with a variable leading edge fan flap for rig performance optimization. The stage was designed for a maximum flow size of 37.4 kg/s (82.3 lb/s) for compatibility with LeRC test facility requirements. Design values at maximum flow for blade tip velocity and stage pressure ratio are 472 m/s (1550 ft/s) and 1.68, respectively.

Cheatham, J. G.↗

NASA NTRS1985

A supersonic fan equipped variable cycle engine for a Mach 2.7 supersonic transport

The concept of a variable cycle turbofan engine with an axially supersonic fan stage as powerplant for a Mach 2.7 supersonic transport was evaluated. Quantitative cycle analysis was used to assess the effects of the fan inlet and blading efficiencies on engine performance. Thrust levels predicted by cycle analysis are shown to match the thrust requirements of a representative aircraft. Fan inlet geometry is discussed and it is shown that a fixed geometry conical spike will provide sufficient airflow throughout the operating regime. The supersonic fan considered consists of a single stage comprising a rotor and stator. The concept is similar in principle to a supersonic compressor, but differs by having a stator which removes swirl from the flow without producing a net rise in static pressure. Operating conditions peculiar to the axially supersonic fan are discussed. Geometry of rotor and stator cascades are presented which utilize a supersonic vortex flow distribution. Results of a 2-D CFD flow analysis of these cascades are presented. A simple estimate of passage losses was made using empirical methods.

Tavares, T. S.↗

NASA NTRS1986

Aerodynamic performance of two fifteen-percent-scale wind-tunnel drive fan designs

An experimental and analytical investigation of two fan blade designs was conducted. The fan blades tested were 15 percent scale models of the blades used in the National Full Scale Aerodynamic Complex fan drive at NASA Ames Research Center. The fan blades were composed of NACA-65 and modified NACA-65-series airfoil design sections. The blades with modified 65-series sections incorporated increased thickness on the upper surface, between the leading edge and the one-half chord position. Twist and taper were the same for both blade designs. The fan blades with modified 65-series sections were found to have an increase in stall margin when they were compared with the unmodified blades. The experimental performance data agreed favorably with theoretical calculations.

Signor, D. B.↗

NASA NTRS1987

Application of advanced computational codes in the design of an experiment for a supersonic throughflow fan rotor

Increased emphasis on sustained supersonic or hypersonic cruise has revived interest in the supersonic throughflow fan as a possible component in advanced propulsion systems. Use of a fan that can operate with a supersonic inlet axial Mach number is attractive from the standpoint of reducing the inlet losses incurred in diffusing the flow from a supersonic flight Mach number to a subsonic one at the fan face. The design of the experiment using advanced computational codes to calculate the components required is described. The rotor was designed using existing turbomachinery design and analysis codes modified to handle fully supersonic axial flow through the rotor. A two-dimensional axisymmetric throughflow design code plus a blade element code were used to generate fan rotor velocity diagrams and blade shapes. A quasi-three-dimensional, thin shear layer Navier-Stokes code was used to assess the performance of the fan rotor blade shapes. The final design was stacked and checked for three-dimensional effects using a three-dimensional Euler code interactively coupled with a two-dimensional boundary layer code. The nozzle design in the expansion region was analyzed with a three-dimensional parabolized viscous code which corroborated the results from the Euler code. A translating supersonic diffuser was designed using these same codes.

Wood, Jerry R.↗

NASA NTRS1988

Large-Scale Advanced Prop-Fan (LAP)

In recent years, considerable attention has been directed toward improving aircraft fuel efficiency. Analytical studies and research with wind tunnel models have demonstrated that the high inherent efficiency of low speed turboprop propulsion systems may now be extended to the Mach .8 flight regime of today's commercial airliners. This can be accomplished with a propeller, employing a large number of thin highly swept blades. The term Prop-Fan has been coined to describe such a propulsion system. In 1983 the NASA-Lewis Research Center contracted with Hamilton Standard to design, build and test a near full scale Prop-Fan, designated the Large Scale Advanced Prop-Fan (LAP). This report provides a detailed description of the LAP program. The assumptions and analytical procedures used in the design of Prop-Fan system components are discussed in detail. The manufacturing techniques used in the fabrication of the Prop-Fan are presented. Each of the tests run during the course of the program are also discussed and the major conclusions derived from them stated.

Degeorge, C. L.↗

NASA NTRS1987

Application of advanced computational codes in the design of an experiment for a supersonic throughflow fan rotor

Wood, Jerry R.↗

NASA NTRS1988

Supersonic through-flow fan assessment

A study was conducted to assess the performance potential of a supersonic through-flow fan engine for supersonic cruise aircraft. It included a mean-line analysis of fans designed to operate with in-flow velocities ranging from subsonic to high supersonic speeds. The fan performance generated was used to estimate the performance of supersonic fan engines designed for four applications: a Mach 2.3 supersonic transport, a Mach 2.5 fighter, a Mach 3.5 cruise missile, and a Mach 5.0 cruise vehicle. For each application an engine was conceptualized, fan performance and engine performance calculated, weight estimates made, engine installed in a hypothetical vehicle, and mission analysis was conducted.

Kepler, C. E.↗

NASA NTRS1988

Measurement of the steady surface pressure distribution on a single rotation large scale advanced prop-fan blade at Mach numbers from 0.03 to 0.78

The aerodynamic pressure distribution was determined on a rotating Prop-Fan blade at the S1-MA wind tunnel facility operated by the Office National D'Etudes et de Recherches Aerospatiale (ONERA) in Modane, France. The pressure distributions were measured at thirteen radial stations on a single rotation Large Scale Advanced Prop-Fan (LAP/SR7) blade, for a sequence of operating conditions including inflow Mach numbers ranging from 0.03 to 0.78. Pressure distributions for more than one power coefficient and/or advanced ratio setting were measured for most of the inflow Mach numbers investigated. Due to facility power limitations the Prop-Fan test installation was a two bladed version of the eight design configuration. The power coefficient range investigated was therefore selected to cover typical power loading per blade conditions which occur within the Prop-Fan operating envelope. The experimental results provide an extensive source of information on the aerodynamic behavior of the swept Prop-Fan blade, including details which were elusive to current computational models and do not appear in the two-dimensional airfoil data.

Bushnell, Peter↗

NASA NTRS1950

Evaluation of a ducted-fan power plant designed for high output and good cruise fuel economy

Theoretical analysis of performance of a ducted-fan power plant designed both for high-output, high-altitude operation at low supersonic Mach numbers and for good fuel economy at lower fight speeds is presented. Performance of ducted fan is compared with performance (with and without tail-pipe burner) of two hypothetical turbojet engines. At maximum power, the ducted fan has propulsive thrust per unit of frontal area between thrusts obtained by turbojet engines with and without tail-pipe burners. At cruise, the ducted fan obtains lowest thrust specific fuel consumption. For equal maximum thrusts, the ducted fan obtains cruising flight duration and range appreciably greater than turbojet engines.

ENGINES, DUCTED PROPELLER↗

NASA NTRS1993

Survey of lift-fan aerodynamic technology

Representatives of NASA Ames Research Center asked that a summary of technology appropriate for lift-fan powered short takeoff/vertical landing (STOVL) aircraft be prepared so that new programs could more easily benefit from past research efforts. This paper represents one of six prepared for that purpose. The authors have conducted or supervised the conduct of research on lift-fan powered STOVL designs and some of their important components for decades. This paper will first address aerodynamic modeling requirements for experimental programs to assure realistic, trustworthy results. It will next summarize the results or efforts to develop satisfactory specialized STOVL components such as inlets and flow deflectors. It will also discuss problems with operation near the ground, aerodynamics while under lift-fan power, and aerodynamic prediction techniques. Finally, results of studies to reduce lift-fan noise will be presented. The paper will emphasize results from large scale experiments, where available, for reasons that will be brought out in the discussion. Some work with lift-engine powered STOVL aircraft is also applicable to lift-fan technology and will be presented herein. Small-scale data will be used where necessary to fill gaps.

Hickey, David H.↗